Juniper SRX 5800 Installation instructions

SRX5800 Services Gateway
Hardware Guide
Published: 2014-06-03
Copyright © 2014, Juniper Networks, Inc.

Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
SRX5800 Services Gateway Hardware Guide
Copyright © 2014, Juniper Networks, Inc.
All rights reserved. Printed in USA.
Revision History
August 2008—530-025322-01 Revision 01 Initial release
October 2008—530-025322-01 Revision 02 Corrected system description section
October 2008—530-025322-01 Revision 03 Minor change to Routing Engine section
April 2009—530-029952-01 Revision 01 Added Flex IOC and port modules
July 2009—530-029952-01 Revision 02
November 2010—Added high-capacity AC power supplies
February 2011—Revised installation procedure
March 2012—Added procedure for adding SPCs to a chassis cluster
August 2012—Added MTU values for IOCs
August 2012—Revised HA LED descriptions
December 2012—Added high-capacity DC power supplies, moved card content into SRX5600 and SRX5800 Services Gateway Card Guide
June 2012—Corrected DC input circuit breaker rating
June 2013—Corrected DC input circuit breaker rating and incorporated additional warnings that the chassis must be connected to earth
ground
December 2013—Added new MPC and 3 new MIC cards
February 2014—Updated the IOC replacement procedure to include the reboot step after inserting the IOC
May 2014—Added the steps to copy certificates when replacing a routing engine in a chassis cluster.
June 2014—Added the EMC compliance requirements in Israel and the procedure to perform initial software configuration using J-Web
The information in this document is current as of the date on the title page.
SOFTWARE LICENSE
The terms and conditions for using this software are described in the software license contained in the acknowledgment to your purchase
order or, to the extent applicable, to any reseller agreement or end-user purchase agreement executed between you and Juniper Networks.
By using this software, you indicate that you understand and agree to be bound by those terms and conditions.
Generally speaking, the software license restricts the manner in which you are permitted to use the software and may contain prohibitions
against certain uses. The software license may state conditions under which the license is automatically terminated. You should consult
the license for further details.
For complete product documentation, please see the Juniper Networks Web site at www.juniper.net/techpubs.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networks
software. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted at
http://www.juniper.net/support/eula.html. By downloading, installing or using such software, you agree to the terms and conditions of
that EULA.
Copyright © 2014, Juniper Networks, Inc.ii

Table of Contents
AboutThisGuide..................................................xi
Objectives......................................................xi
Audience.......................................................xi
DocumentationConventions.......................................xi
SRX Series Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . xiii
ObtainingDocumentation........................................xiv
DocumentationFeedback........................................xiv
RequestingTechnicalSupport.....................................xiv
Part 1 SRX5800 Services Gateway Overview
Chapter 1 Introduction to the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . 3
SRX5800 Services Gateway Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SRX5800 Services Gateway Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3
SRX5800 Services Gateway Component Redundancy . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2 SRX5800 Services Gateway Hardware Components . . . . . . . . . . . . . . . . . . . 7
SRX5800ServicesGatewayChassis....................................7
SRX5800 Services Gateway Rack-Mounting Hardware . . . . . . . . . . . . . . . . . . . . 10
SRX5800 Services Gateway Card Cage and Slots . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SRX5800 Services Gateway Midplane Description . . . . . . . . . . . . . . . . . . . . . . . . 12
SRX5800 Services Gateway Interface Card Description . . . . . . . . . . . . . . . . . . . . 13
SRX5800 Services Gateway SPC Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SRX5800 Services Gateway Host Subsystem Description . . . . . . . . . . . . . . . . . . . 17
SRX5800 Services Gateway SCB Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SRX5800 Services Gateway Routing Engine Description . . . . . . . . . . . . . . . . . . . . 19
SRX5800 Services Gateway Craft Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SRX5800 Services Gateway Craft Interface Overview . . . . . . . . . . . . . . . . . . 20
SRX5800 Services Gateway Craft Interface Alarm LEDs and Alarm
Cutoff/LampTestButton......................................21
SRX5800 Services Gateway Craft Interface Host Subsystem LEDs . . . . . . . 22
SRX5800 Services Gateway Craft Interface Power Supply LEDs . . . . . . . . . . 23
SRX5800 Services Gateway Craft Interface Card OK/Fail LEDs . . . . . . . . . . 23
SRX5800 Services Gateway Craft Interface Fan LEDs . . . . . . . . . . . . . . . . . . 24
SRX5800 Services Gateway Craft Interface Online Buttons . . . . . . . . . . . . . 24
SRX5800 Services Gateway Craft Interface Alarm Relay Contacts . . . . . . . . 26
SRX5800 Services Gateway Power System Description . . . . . . . . . . . . . . . . . . . . 27
SRX5800 Services Gateway Power System Overview . . . . . . . . . . . . . . . . . . 28
SRX5800 Services Gateway High-Capacity AC Power Supply . . . . . . . . . . . . 31
SRX5800 Services Gateway High-Capacity AC Power Supply LEDs . . . . . . . 33
SRX5800 Services Gateway Standard-Capacity AC Power Supply . . . . . . . 34
iiiCopyright © 2014, Juniper Networks, Inc.

SRX5800 Services Gateway Standard-Capacity AC Power Supply LEDs . . . 35
SRX5800 Services Gateway High-Capacity DC Power Supply . . . . . . . . . . . 36
SRX5800 Services Gateway High-Capacity DC Power Supply LEDs . . . . . . . 38
SRX5800 Services Gateway Standard-Capacity DC Power Supply . . . . . . . 39
SRX5800 Services Gateway Standard-Capacity DC Power Supply LEDs . . 40
SRX5800 Services Gateway Cooling System Description . . . . . . . . . . . . . . . . . . . 41
SRX5800 Services Gateway Cable Manager Description . . . . . . . . . . . . . . . . . . . 43
Part 2 Setting Up the SRX5800 Services Gateway
Chapter 3 SRX5800 Services Gateway Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Overview of Installing the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . 47
Chapter 4 Preparing the Site for the SRX5800 Services Gateway Installation . . . . . . 49
Site Preparation Checklist for the SRX5800 Services Gateway . . . . . . . . . . . . . . 49
SRX5800 Services Gateway Rack Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 50
SRX5800 Services Gateway Rack Size and Strength Requirements . . . . . . . 51
Spacing of Rack-Mounting Bracket Holes for the SRX5800 Services
Gateway...................................................52
Connection to Building Structure for the SRX5800 Services Gateway
Rack ......................................................52
Clearance Requirements for SRX5800 Services Gateway Airflow and
HardwareMaintenance.......................................52
SRX5800 Services Gateway Cabinet Requirements . . . . . . . . . . . . . . . . . . . . . . . 53
SRX5800 Services Gateway Cabinet Size and Clearance Requirements . . . 54
SRX5800 Services Gateway Cabinet Airflow Requirements . . . . . . . . . . . . . 54
Chapter 5 Unpacking the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Tools and Parts Required to Unpack the SRX5800 Services Gateway . . . . . . . . . 57
Unpacking the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Verifying the SRX5800 Services Gateway Parts Received . . . . . . . . . . . . . . . . . . 59
Chapter 6 Installing the SRX5800 Services Gateway Mounting Hardware . . . . . . . . . 63
Installing the SRX5800 Services Gateway Mounting Hardware for a Four-Post
RackorCabinet.................................................63
Installing the SRX5800 Services Gateway Mounting Hardware in an Open-Frame
Rack..........................................................65
Chapter 7 Installing the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Tools Required to Install the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . 69
Removing Components from the SRX5800 Chassis Before Installing It in the
Rack .........................................................69
Removing the Power Supplies Before Installing the SRX5800 Services
GatewayChassis............................................70
Removing the Cable Manager Before Installing the SRX5800 Services
GatewayChassis.............................................71
Removing Fan Trays Before Installing the SRX5800 Services Gateway
Chassis ....................................................72
Copyright © 2014, Juniper Networks, Inc.iv
SRX5800 Services Gateway Hardware Guide

Removing Cards Before Installing the SRX5800 Services Gateway
Chassis ....................................................74
Installing the SRX5800 Services Gateway Chassis in the Rack . . . . . . . . . . . . . . . 76
Reinstalling Components in the SRX5800 Services Gateway Chassis After
InstallingItintheRack...........................................79
Reinstalling Power Supplies After Installing the SRX5800 Services Gateway
Chassis....................................................79
Reinstalling Fan Trays After Installing the SRX5800 Services Gateway
Chassis....................................................80
Reinstalling Cards After Installing the SRX5800 Services Gateway
Chassis....................................................82
Reinstalling the Cable Manager After Installing the SRX5800 Services
GatewayChassis............................................84
Chapter 8 Connecting the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . 87
Tools and Parts Required for SRX5800 Services Gateway Connections . . . . . . . 87
Connecting the SRX5800 Services Gateway to Management and Alarm
Devices .......................................................88
Connecting the SRX5800 Services Gateway to a Network for Out-of-Band
Management...............................................88
Connecting the SRX5800 Services Gateway to a Management Console or
anAuxiliaryDevice..........................................89
Connecting an SRX5800 Services Gateway to an External Alarm-Reporting
Device ....................................................90
Connecting Network Cables to SRX5800 Services Gateway IOCs and Port
Modules .......................................................91
Chapter 9 Grounding and Providing Power to the SRX5800 Services Gateway . . . . . 95
Tools and Parts Required for SRX5800 Services Gateway Grounding and Power
Connections ...................................................95
Grounding the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Connecting Power to an AC-Powered SRX5800 Services Gateway . . . . . . . . . . . 97
Powering On an AC-Powered SRX5800 Services Gateway . . . . . . . . . . . . . . . . . 101
Connecting Power to a DC-Powered SRX5800 Services Gateway . . . . . . . . . . . 102
Powering On a DC-Powered SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . 105
Powering Off the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Chapter 10 Configuring Junos OS for the SRX5800 Services Gateway . . . . . . . . . . . . 109
SRX5800 Services Gateway Software Configuration Overview . . . . . . . . . . . . . 109
Initially Configuring the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . . . 110
Performing Initial Software Configuration Using J-Web . . . . . . . . . . . . . . . . . . . . . 113
Configuring Root Authentication and the Management Interface from the
CLI .......................................................114
Configuring Interfaces, Zones, and Policies with J-Web . . . . . . . . . . . . . . . . . 114
ConfiguringtheHostname....................................115
ConfiguringInterfaces........................................115
Configuring Zones and Assigning Interfaces . . . . . . . . . . . . . . . . . . . . . . 116
ConfiguringSecurityPolicies..................................116
vCopyright © 2014, Juniper Networks, Inc.
Table of Contents

Part 3 SRX5800 Services Gateway Hardware Maintenance,
Replacement, and Troubleshooting Procedures
Chapter 11 Maintaining the SRX5800 Services Gateway Hardware Components . . . 121
Tools and Parts Required to Maintain the SRX5800 Services Gateway . . . . . . . . 121
Routine Maintenance Procedures for the SRX5800 Services Gateway . . . . . . . . 121
Maintaining the SRX5800 Cooling System Components . . . . . . . . . . . . . . . . . . . 122
Maintaining the Air Filter on the SRX5800 Services Gateway . . . . . . . . . . . . 122
Maintaining the Fan Trays on the SRX5800 Services Gateway . . . . . . . . . . . 123
Maintaining the SRX5800 Services Gateway Host Subsystem and SCBs . . . . . . 123
Maintaining the SRX5800 Packet Forwarding Engine Components . . . . . . . . . . 125
Maintaining Interface Cards and SPCs on the SRX5600 Services
Gateway ..................................................125
Maintaining MICs and Port Modules on the SRX5800 Services Gateway . . . 127
Maintaining SRX5800 Services Gateway Network Cables . . . . . . . . . . . . . . 128
Handling and Storing SRX5800 Services Gateway Cards . . . . . . . . . . . . . . . . . . 129
SRX5800 Services Gateway Card Terminology . . . . . . . . . . . . . . . . . . . . . . . 129
Holding an SRX5800 Services Gateway Card . . . . . . . . . . . . . . . . . . . . . . . . 130
Storing an SRX5800 Services Gateway Card . . . . . . . . . . . . . . . . . . . . . . . . . 132
Maintaining SRX5800 Services Gateway Power Supplies . . . . . . . . . . . . . . . . . . 133
Chapter 12 Troubleshooting the SRX5800 Services Gateway Hardware
Components.....................................................135
Troubleshooting Resources for the SRX5800 Services Gateway . . . . . . . . . . . . . 135
Troubleshooting the SRX5800 Services Gateway with the Junos OS CLI . . 135
Troubleshooting the SRX5800 Services Gateway with Chassis and Interface
AlarmMessages............................................136
Troubleshooting the SRX5800 Services Gateway with Alarm Relay
Contacts ..................................................136
Troubleshooting the SRX5800 Services Gateway with the Craft Interface
LEDs .....................................................136
Troubleshooting the SRX5800 Services Gateway with the Component
LEDs .....................................................137
Juniper Networks Technical Assistance Center . . . . . . . . . . . . . . . . . . . . . . . 138
Troubleshooting the SRX5800 Services Gateway Cooling System . . . . . . . . . . . 138
Troubleshooting SRX5800 Services Gateway Interface Cards . . . . . . . . . . . . . . 139
Troubleshooting SRX5800 Services Gateway MICs and Port Modules . . . . . . . . 140
Troubleshooting SRX5800 Services Gateway SPCs . . . . . . . . . . . . . . . . . . . . . . . 141
Troubleshooting the SRX5800 Services Gateway Power System . . . . . . . . . . . . 142
Chapter 13 Replacing SRX5800 Services Gateway Hardware Components . . . . . . . . 145
SRX5800 Services Gateway Field-Replaceable Units . . . . . . . . . . . . . . . . . . . . . 146
Tools and Parts Required to Replace SRX5800 Services Gateway Hardware
Components ..................................................146
Replacing the SRX5800 Services Gateway Craft Interface . . . . . . . . . . . . . . . . . 148
Disconnecting the Alarm Relay Wires from the SRX5800 Services Gateway
Craft Interface .............................................148
Removing the SRX5800 Services Gateway Craft Interface . . . . . . . . . . . . . 148
Installing the SRX5800 Services Gateway Craft Interface . . . . . . . . . . . . . . 149
Copyright © 2014, Juniper Networks, Inc.vi
SRX5800 Services Gateway Hardware Guide

Connecting the Alarm Relay Wires to the SRX5800 Services Gateway Craft
Interface ..................................................150
Replacing an SRX5800 Services Gateway Fan Tray . . . . . . . . . . . . . . . . . . . . . . . 150
Removing an SRX5800 Services Gateway Fan Tray . . . . . . . . . . . . . . . . . . . . 151
Installing an SRX5800 Services Gateway Fan Tray . . . . . . . . . . . . . . . . . . . . 153
Replacing the SRX5800 Services Gateway Air Filter . . . . . . . . . . . . . . . . . . . . . . 155
Removing the SRX5800 Services Gateway Air Filter . . . . . . . . . . . . . . . . . . . 155
Installing the SRX5800 Services Gateway Air Filter . . . . . . . . . . . . . . . . . . . 156
Replacing SRX5800 Services Gateway Host Subsystem Components . . . . . . . . 157
Taking the SRX5800 Services Gateway Host Subsystem Offline . . . . . . . . . 157
Operating and Positioning the SRX5800 Services Gateway SCB
Ejectors...................................................158
Replacing an SRX5800 Services Gateway SCB . . . . . . . . . . . . . . . . . . . . . . 158
Removing an SRX5800 Services Gateway SCB . . . . . . . . . . . . . . . . . . . 159
Installing an SRX5800 Services Gateway SCB . . . . . . . . . . . . . . . . . . . 160
Replacing the SRX5800 Services Gateway Routing Engine . . . . . . . . . . . . . 162
Removing the SRX5800 Services Gateway Routing Engine . . . . . . . . . 163
Installing the SRX5800 Services Gateway Routing Engine . . . . . . . . . . 164
Replacing Connections to SRX5800 Services Gateway Routing Engine Interface
Ports.........................................................167
Replacing the Management Ethernet Cable on an SRX5800 Services
Gateway ..................................................167
Replacing the SRX5800 Services Gateway Console or Auxiliary Cable . . . . 167
Replacing SRX5800 Services Gateway IOCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Removing an SRX5800 Services Gateway IOC . . . . . . . . . . . . . . . . . . . . . . . 168
Installing an SRX5800 Services Gateway IOC . . . . . . . . . . . . . . . . . . . . . . . . 170
Replacing SRX5800 Services Gateway Flex IOCs . . . . . . . . . . . . . . . . . . . . . . . . . 173
Removing an SRX5800 Services Gateway Flex IOC . . . . . . . . . . . . . . . . . . . 173
Installing an SRX5800 Services Gateway Flex IOC . . . . . . . . . . . . . . . . . . . . 175
Replacing SRX5800 Services Gateway Port Modules . . . . . . . . . . . . . . . . . . . . . . 177
Removing an SRX5800 Services Gateway Port Module . . . . . . . . . . . . . . . . 177
Installing an SRX5800 Services Gateway Port Module . . . . . . . . . . . . . . . . . 179
Replacing SRX5800 Services Gateway MPCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Removing an SRX5800 Services Gateway MPC . . . . . . . . . . . . . . . . . . . . . . 181
Installing an SRX5800 Services Gateway MPC . . . . . . . . . . . . . . . . . . . . . . . 183
Replacing SRX5800 Services Gateway MICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Removing an SRX5800 Services Gateway MIC . . . . . . . . . . . . . . . . . . . . . . . 185
Installing an SRX5800 Services Gateway MIC . . . . . . . . . . . . . . . . . . . . . . . 188
Installing MPCs and MICs in an Operating SRX5800 Services Gateway Chassis
Cluster .......................................................190
Replacing an SRX5800 Services Gateway Network Interface Cable . . . . . . . . . . 193
Removing an SRX5800 Services Gateway Network Interface Cable . . . . . . 193
Installing an SRX5800 Services Gateway Network Interface Cable . . . . . . . 194
Replacing SRX5800 Services Gateway SPCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Removing an SRX5800 Services Gateway SPC . . . . . . . . . . . . . . . . . . . . . . 196
Installing an SRX5800 Services Gateway SPC . . . . . . . . . . . . . . . . . . . . . . . 198
Replacing SPCs in an Operating SRX5800 Services Gateway Chassis Cluster . . 203
viiCopyright © 2014, Juniper Networks, Inc.
Table of Contents

Replacing SRX5800 Services Gateway XFP and SFP Transceivers . . . . . . . . . . 206
Removing an SRX5800 Services Gateway SFP or XFP Transceiver . . . . . . 206
Installing an SRX5800 Services Gateway SFP or XFP Transceiver . . . . . . . 207
Upgrading an SRX5800 Services Gateway from Standard-Capacity to
High-CapacityPowerSupplies...................................208
Replacing an SRX5800 Services Gateway AC Power Supply . . . . . . . . . . . . . . . . 211
Removing an SRX5800 Services Gateway AC Power Supply . . . . . . . . . . . . 211
Installing an SRX5800 Services Gateway AC Power Supply . . . . . . . . . . . . . 214
Replacing an SRX5800 Services Gateway DC Power Supply . . . . . . . . . . . . . . . 216
Removing an SRX5800 Services Gateway DC Power Supply . . . . . . . . . . . . 216
Installing an SRX5800 Services Gateway DC Power Supply . . . . . . . . . . . . 219
Replacing an SRX5800 Services Gateway AC Power Supply Cord . . . . . . . . . . . 224
Disconnecting an SRX5800 Services Gateway AC Power Supply Cord . . . . 224
Connecting an SRX5800 Services Gateway AC Power Supply Cord . . . . . . 224
Replacing an SRX5800 Services Gateway DC Power Supply Cable . . . . . . . . . . 226
Disconnecting an SRX5800 Services Gateway DC Power Supply Cable . . . 226
Connecting an SRX5800 Services Gateway DC Power Supply Cable . . . . . 227
Replacing the SRX5800 Services Gateway Cable Manager . . . . . . . . . . . . . . . . 229
Removing the SRX5800 Services Gateway Cable Manager . . . . . . . . . . . . 230
Installing the SRX5800 Services Gateway Cable Manager . . . . . . . . . . . . . 230
Part 4 Appendixes
Appendix A Safety and Regulatory Compliance Information . . . . . . . . . . . . . . . . . . . . . . 235
SRX5800 Services Gateway Definition of Safety Warning Levels . . . . . . . . . . . . 235
SRX5800 Services Gateway General Safety Guidelines and Warnings . . . . . . . . 237
Additional SRX5800 Services Gateway Warnings . . . . . . . . . . . . . . . . . . . . . . . . 238
QualifiedPersonnelWarning.....................................238
RestrictedAccessAreaWarning..................................239
Preventing Electrostatic Discharge Damage to the SRX5800 Services
Gateway......................................................241
SRX5800 Services Gateway Fire Safety Requirements and Fire Suppression
Equipment....................................................243
SRX5800 Services Gateway Installation Safety Guidelines and Warnings . . . . 244
ChassisLiftingGuidelines........................................244
Installation Instructions Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Rack-Mounting Requirements and Warnings . . . . . . . . . . . . . . . . . . . . . . . . 246
Ramp Warning ................................................249
SRX5800 Services Gateway Laser and LED Safety Guidelines and Warnings . . 250
GeneralLaserSafetyGuidelines..................................250
Class1LaserWarning...........................................251
Class1LEDProductWarning......................................251
LaserBeamWarning............................................252
Radiation from Open Port Apertures Warning . . . . . . . . . . . . . . . . . . . . . . . . 253
SRX5800 Services Gateway Maintenance and Operational Safety Guidelines
andWarnings .................................................254
BatteryHandlingWarning.......................................254
JewelryRemovalWarning........................................255
LightningActivityWarning.......................................256
Copyright © 2014, Juniper Networks, Inc.viii
SRX5800 Services Gateway Hardware Guide

OperatingTemperatureWarning..................................257
ProductDisposalWarning.......................................258
SRX5800 Services Gateway Electrical Safety Guidelines and Warnings . . . . . . 259
InCaseofElectricalAccident.....................................259
General Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . 260
DC Power Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . 264
SRX5800 Services Gateway Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . 270
SRX5800 Services Gateway Compliance Statements for EMC
Requirements..................................................271
Canada.......................................................271
EuropeanCommunity ...........................................271
Israel.........................................................272
Japan ........................................................272
UnitedStates..................................................272
Appendix B SRX5800 Services Gateway Environmental Specifications . . . . . . . . . . . 273
SRX5800 Services Gateway Environmental Specifications . . . . . . . . . . . . . . . . 273
Appendix C SRX5800 Services Gateway Power Guidelines, Requirements, and
Specifications ...................................................275
Calculating Power Requirements for the SRX5800 Services Gateway . . . . . . . . 275
SRX5800 Services Gateway Chassis Grounding Specifications . . . . . . . . . . . . . 280
SRX5800 Services Gateway Chassis Grounding Point Specifications . . . . 280
SRX5800 Services Gateway Grounding-Cable Lug Specification . . . . . . . . 281
SRX5800 Services Gateway Grounding Cable Specifications . . . . . . . . . . . 282
SRX5800 Services Gateway AC Power Specifications and Requirements . . . . . 282
SRX5800 Services Gateway AC Power Supply Specifications . . . . . . . . . . . 282
AC Power Circuit Breaker Requirements for the SRX5800 Services
Gateway..................................................283
AC Power Cord Specifications for the SRX5800 Services Gateway . . . . . . 284
SRX5800 Services Gateway DC Power Specifications and Requirements . . . . 286
SRX5800 Services Gateway DC Power Supply Specifications . . . . . . . . . . 286
DC Power Circuit Breaker Requirements for the SRX5800 Services
Gateway..................................................287
DC Power Source Cabling for the SRX5800 Services Gateway . . . . . . . . . . 287
DC Power Cable Specifications for the SRX5800 Services Gateway . . . . . 289
DC Power Cable Lug Specifications for the SRX5800 Services Gateway . . 289
SRX5800 Services Gateway Electrical Wiring Guidelines . . . . . . . . . . . . . . . . . . 290
Appendix D Cable and Wire Guidelines and Specifications for the SRX5800 Services
Gateway ........................................................293
Network Cable Specifications and Guidelines for the SRX5800 Services
Gateway .....................................................293
Signal Loss in Multimode and Single-Mode Fiber-Optic Cable for the
SRX5800ServicesGateway..................................293
Attenuation and Dispersion in Fiber-Optic Cable for the SRX5800 Services
Gateway..................................................294
Calculating Power Budget for Fiber-Optic Cable for the SRX5800 Services
Gateway..................................................295
ixCopyright © 2014, Juniper Networks, Inc.
Table of Contents

Calculating Power Margin for Fiber-Optic Cable for the SRX5800 Services
Gateway..................................................295
Routing Engine Interface Cable and Wire Specifications for the SRX5800
ServicesGateway...........................................297
Alarm Relay Contact Wire Specifications for the SRX5800 Services
Gateway..................................................298
Console Port Cable and Wire Specifications for the SRX5800 Services
Gateway..................................................298
AppendixE CableConnectorPinouts.........................................299
RJ-45 Connector Pinouts for the SRX5800 Services Gateway Routing Engine
Ethernet Port .................................................299
RJ-45 Connector Pinouts for the SRX5800 Services Gateway Routing Engine
AuxiliaryandConsolePorts......................................300
Appendix F Contacting Customer Support and Returning the SRX5800 Services
GatewayHardware...............................................301
Return Procedure for the SRX5800 Services Gateway . . . . . . . . . . . . . . . . . . . . 301
Locating SRX5800 Services Gateway Component Serial Numbers . . . . . . . . . . 302
Listing the SRX5800 Services Gateway Component Serial Numbers with
theCommand-LineInterface.................................302
Locating the SRX5800 Services Gateway Chassis Serial Number Label . . 304
Locating the SRX5800 Services Gateway Power Supply Serial Number
Label ....................................................304
Locating the SRX5800 Services Gateway Craft Interface Serial Number
Label ....................................................305
Contacting Customer Support to Obtain Return Materials Authorization for the
SRX5800ServicesGateway.....................................306
Information You Might Need to Supply to JTAC . . . . . . . . . . . . . . . . . . . . . . 306
ContactingCustomerSupport....................................306
Packing the SRX5800 Services Gateway or a Component for Shipment . . . . . . 307
Required Tools and Parts for Packing the SRX5800 Services Gateway . . . 307
Packing the SRX5800 Services Gateway for Shipment . . . . . . . . . . . . . . . . 308
Packing SRX5800 Services Gateway Components for Shipment . . . . . . . . 309
Part 5 Index
Index ............................................................313
Copyright © 2014, Juniper Networks, Inc.x
SRX5800 Services Gateway Hardware Guide

About This Guide
•Objectives on page xi
•Audience on page xi
•Documentation Conventions on page xi
•SRX Series Documentation and Release Notes on page xiii
•Obtaining Documentation on page xiv
•Documentation Feedback on page xiv
•Requesting Technical Support on page xiv
Objectives
This guide describes hardware components and installation, basic configuration, and
basic troubleshooting procedures for the Juniper Networks SRX5800 Services Gateway.
It explains how to prepare your site for services gateway installation, unpack and install
the hardware, power on the services gateway, perform initial software configuration, and
perform routine maintenance. After completing the installation and basic configuration
procedures covered in this guide, see the Junos OS configuration guides for information
about further Junos OS configuration.
Audience
This guide is designed for network administrators who are installing and maintaining a
Juniper Networks SRX5800 Services Gateway or preparing a site for services gateway
installation. To use this guide, you need a broad understanding of networks in general
and the Internet in particular, networking principles, and network configuration. Any
detailed discussion of these concepts is beyond the scope of this guide.
Documentation Conventions
Table 1 on page xii defines the notice icons used in this guide.
xiCopyright © 2014, Juniper Networks, Inc.

Table 1: Notice Icons
DescriptionMeaningIcon
Indicates important features or instructions.Informational note
Indicates a situation that might result in loss of data or hardware damage.Caution
Alerts you to the risk of personal injury or death.Warning
Alerts you to the risk of personal injury from a laser.Laser warning
Indicates helpful information.Tip
Alerts you to a recommended use or implementation.Best practice
Table 2 on page xii defines the text and syntax conventions used in this guide.
Table 2: Text and Syntax Conventions
ExamplesDescriptionConvention
To enter configuration mode, type the
configure command:
user@host> configure
Represents text that you type.Bold text like this
user@host> show chassis alarms
No alarms currently active
Represents output that appears on the
terminal screen.
Fixed-width text like this
•A policy term is a named structure
that defines match conditions and
actions.
•Junos OS CLI User Guide
•RFC 1997, BGP Communities Attribute
•Introduces or emphasizes important
new terms.
•Identifies guide names.
•Identifies RFC and Internet draft titles.
Italic text like this
Configure the machine’s domain name:
[edit]
root@# set system domain-name
domain-name
Represents variables (options for which
you substitute a value) in commands or
configuration statements.
Italic text like this
Copyright © 2014, Juniper Networks, Inc.xii
SRX5800 Services Gateway Hardware Guide

Table 2: Text and Syntax Conventions (continued)
ExamplesDescriptionConvention
•To configure a stub area, include the
stub statement at the [edit protocols
ospf area area-id] hierarchy level.
•The console port is labeled CONSOLE.
Represents names of configuration
statements, commands, files, and
directories; configuration hierarchy levels;
or labels on routing platform
components.
Text like this
stub <default-metric metric>;Encloses optional keywords or variables.< > (angle brackets)
broadcast | multicast
(string1 |string2 |string3)
Indicates a choice between the mutually
exclusive keywords or variables on either
side of the symbol. The set of choices is
often enclosed in parentheses for clarity.
| (pipe symbol)
rsvp { # Required for dynamic MPLS onlyIndicates a comment specified on the
same line as the configuration statement
to which it applies.
# (pound sign)
community name members [
community-ids ]
Encloses a variable for which you can
substitute one or more values.
[ ] (square brackets)
[edit]
routing-options {
static {
route default {
nexthop address;
retain;
}
}
}
Identifies a level in the configuration
hierarchy.
Indention and braces ( { } )
Identifies a leaf statement at a
configuration hierarchy level.
; (semicolon)
GUI Conventions
•In the Logical Interfaces box, select
All Interfaces.
•To cancel the configuration, click
Cancel.
Represents graphical user interface (GUI)
items you click or select.
Bold text like this
In the configuration editor hierarchy,
select Protocols>Ospf.
Separates levels in a hierarchy of menu
selections.
>(bold right angle bracket)
SRX Series Documentation and Release Notes
For a list of related SRX Series documentation, see
http://www.juniper.net/techpubs/software/junos/. If the information in the latest release
notes differs from the information in the documentation, follow the Junos OS Release
Notes.
xiiiCopyright © 2014, Juniper Networks, Inc.
About This Guide

Obtaining Documentation
To obtain the most current version of all Juniper Networks technical documentation, see
the product documentation page on the Juniper Networks website at
http://www.juniper.net/ .
To order printed copies of this guide and other Juniper Networks technical documents,
or to order a documentation CD that contains this guide, contact your sales representative.
Copies of the Management Information Bases (MIBs) available in a software release are
included in the documentation CDs and are at www.juniper.net/techpubs/.
Documentation Feedback
We encourage you to provide feedback, comments, and suggestions so that we can
improve the documentation. You can send your comments to
[e-mail], or fill out the documentation feedback form at
http://www.juniper.net/techpubs/docbug/docbugreport.html. If you are using e-mail, be
sure to include the following information with your comments:
•Document Name
•Document part number
•Page number
•Software release version (not required for Network Operations Guides [NOGs])
Requesting Technical Support
Technical product support is available through the Juniper Networks Technical Assistance
Center (JTAC). If you are a customer with an active J-Care or JNASC support contract,
or are covered under warranty, and need postsales technical support, you can access
our tools and resources online or open a case with JTAC.
•JTAC policies—For a complete understanding of our JTAC procedures and policies,
review the JTAC User Guide located at
http://www.juniper.net/customers/support/downloads/710059.pdf.
•Product warranties—For product warranty information, visit
http://www.juniper.net/support/warranty/.
•JTAC Hours of Operation—The JTAC centers have resources available 24 hours a day,
7 days a week, 365 days a year.
Self-Help Online Tools and Resources
For quick and easy problem resolution, Juniper Networks has designed an online
self-service portal called the Customer Support Center (CSC) that provides you with the
following features:
Copyright © 2014, Juniper Networks, Inc.xiv
SRX5800 Services Gateway Hardware Guide

•Find CSC offerings: http://www.juniper.net/customers/support/
•Search for known bugs: http://www2.juniper.net/kb/
•Find product documentation: www.juniper.net/techpubs/
•Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/
•Download the latest versions of software and review release notes:
http://www.juniper.net/customers/csc/software/
•Search technical bulletins for relevant hardware and software notifications:
https://www.juniper.net/alerts/
•Join and participate in the Juniper Networks Community Forum:
http://www.juniper.net/company/communities/
•Open a case online in the CSC Case Manager: http://www.juniper.net/cm/
To verify service entitlement by product serial number, use our Serial Number Entitlement
(SNE) Tool located at https://tools.juniper.net/SerialNumberEntitlementSearch/.
Opening a Case with JTAC
You can open a case with JTAC on the Web or by telephone.
•Use the Case Manager tool in the CSC at http://www.juniper.net/cm/ .
•Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).
For international or direct-dial options in countries without toll-free numbers, visit us at
http://www.juniper.net/support/requesting-support.html.
xvCopyright © 2014, Juniper Networks, Inc.
About This Guide

Copyright © 2014, Juniper Networks, Inc.xvi
SRX5800 Services Gateway Hardware Guide

PART 1
SRX5800 Services Gateway Overview
•Introduction to the SRX5800 Services Gateway on page 3
•SRX5800 Services Gateway Hardware Components on page 7
1Copyright © 2014, Juniper Networks, Inc.

Copyright © 2014, Juniper Networks, Inc.2
SRX5800 Services Gateway Hardware Guide

CHAPTER 1
Introduction to the SRX5800 Services
Gateway
•SRX5800 Services Gateway Description on page 3
•SRX5800 Services Gateway Physical Specifications on page 3
•SRX5800 Services Gateway Component Redundancy on page 5
SRX5800 Services Gateway Description
The SRX5800 Services Gateway is a high-performance, highly scalable, carrier-class
security device with multi-processor architecture.
The services gateway provides 12 slots that you can populate with 2 or 3 Switch Control
Boards (SCBs) and up to 12 additional cards of the following types:
•Services Processing Cards (SPCs) provide the processing capacity to run integrated
services such as firewall, IPsec, and IDP.
•Modular PIC Concentrators (MPCs) provide Ethernet interfaces that connect the
services gateway to your network.
•I/O cards (IOCs) provide Ethernet interfaces that connect the services gateway to your
network.
•Flex IOCs are similar to IOCs, but have slots for port modules that allow you greater
flexibility in adding different types of Ethernet ports to your services gateway.
Related
Documentation
SRX5800 Services Gateway Physical Specifications on page 3•
•SRX5800 Services Gateway Chassis on page 7
•SRX5800 Services Gateway Card Cage and Slots on page 11
•SRX5800 Services Gateway Component Redundancy on page 5
SRX5800 Services Gateway Physical Specifications
Table 3 on page 4 summarizes the physical specifications for the services gateway
chassis.
3Copyright © 2014, Juniper Networks, Inc.

Table 3: Physical Specifications
ValueDescription
27.75 in. (70.5 cm) highHeightChassis dimensions
17.37 in. (44.1 cm) wideWidth
23.0 in. (58.4 cm) deep from front-mounting bracket to
chassis rear
27.8 in. (70.6 cm) total depth including cable management
system
Depth, with standard-capacity power
supplies
25.5 in. (64.8 cm) deep from front-mounting bracket to
chassis rear
30.3 in. (77.0 cm) total depth including cable management
system
Depth, with high-capacity AC power
supplies
27.8 in. (70.6 cm) deep from front-mounting bracket to
chassis rear
32.6 in. (82.8 cm) total depth including cable
management system
Depth, with high-capacity DC power
supplies
Chassis with midplane, fan tray, air filter, and cable
manager: 150 lb (60.4 kg)
Maximum configuration: 400 lb (182 kg)
Services gateway weight
2.4 lb (1.1 kg)Routing Engine weight
9.6 lb (4.4 kg)SCB weight
13.1 lb (5.9 kg)MPC weight (with two MICs)
13.1 lb (5.9 kg)IOC weight
1.1 lb (0.5 kg)Craft interface weight
4.2 lb (1.9 kg)Fan tray weight
1.0 lb (0.5 kg)Air filter weight
0.3 lb (0.14 kg)Cable management weight
3.8 lb (1.7 kg)Standard-capacity DC power supply weight
12.0 lb (5.5 kg)High-capacity DC power supply weight
5.0 lb (2.3 kg)Standard-capacity AC power supply weight
12.0 lb (5.5 kg)High-capacity AC power supply weight
Copyright © 2014, Juniper Networks, Inc.4
SRX5800 Services Gateway Hardware Guide