JUNO JDA 5330 Technical manual

1
Montage- und Gebrauchsanweisung
für den Dunstabzug
Instruction on mounting and use of the cooker hood
JDA 5330

2
A
BBC
CC
D
D
Abb. 1
Fig. 1
Abb. 2 - Fig. 2
Abb. 3 - Fig. 3
F

3
E
F
G
H
SS
Abb. 4 - Fig. 4
Abb. 5 - Fig. 5 Abb. 6 - Fig. 6

7
View of the hood - Fig. 1
1) Motor speed switch
2) Light switch
3) Extractable drawer
4) Metal grease filter
5) Cooking surface lighting
Use
The hood may be used in 2 ways:
External exhausting system
The air is expelled outside by means of
a pipe to be connected to the coupling
flange A (fig. 2).
Connecting the exhausting pipe
ThecouplingringAhasadiameterof120mm.
We suggest to use Ø 120 mm exhausting
pipe.
Recycling version (filtering)
Theairispurifiedbymeansofacarbonfilter
and then returned to the room.
Theactivecarbonfiltercanbeorderedfrom
the supplier.
To install the filter, proceed as follow:
fitthefilterinto itsseat B andfix withthetwo
hooks C (fig. 3).
The filtered air is discharged above the top
cabinet.
Thebaffleplate D (fig.2)can befitted tothe
outlet hole using the screws supplied.
Installation
When installed, the hood must be not less
than 43 cm. above electric burners or 65
cm. above gas or mixed-fuel burners.
Warning!
— Thehoodcannotbeconnectedtofluesof
other appliances that run on energy
sources other than electricity.
— When the hood is used at the same time of
otherappliancesthatrunonenergysources
otherthanelectricity,provisionmustbemade
for an adequate supply of air.
— No food must be cooked flambé
underneath the hood.
The use of an unprotected flame is
dangerousforthefiltersandcouldcause
fires.
Therefore,neveruseanopenflameunder
thehood.Whenfryingfoods,neverleave
the pan alone because the cooking oil
could flare up.
— Please, keep to the provisions of official
directivesregardingthequestionoffume
discharge.
— The manufacturers refuse to accept any
responsibility for damage to the hood or
its catching on fire because of failure to
observe the above instructions.
Suggestions for the installation and
use of the hood
— The horizontal sections of the pipe must
be slanted slightly downwards (about
10%) to ensure the condensed vapour
not to come back on the motor of the
hood.
— The best performance of the unit is
obtained in the exhaust mode, therefore
inthelimitsofthepossibilitiesitisadvised
tousetheexternalexhaust(suction)type.
— Thebestperformancesareobtainedwith
short pipes (max. 4 m) and with few
curves.
Electric connection
Before completing any connection, make
surethehousevoltagecorrespondswiththe
voltage indicated on the label affixed inside
the hood.
The hood is supplied with a standard plug;
connect it to a correspondingly standard
socket.
In the case is intended to connect the
appliance permanently to the mains after
having removed the plug supplied, must be
fitted a two-pole switch conforming to
regulations with an opening distance
between contacts of not less than 3mm.
The manufacturers are not liable for any
problems caused by the user’s failure to
observe the above instructions.

8
ventilator(leftswitch)andoneforilluminating
the work surface (right switch).
Maintenance
Before performing any maintenance
operation, disconnect the hood from the
electricity.
Metal grease filter
Wash the filter, in a dishwasher or with
detergent and water, periodically according
to how often the appliance is used, but at
least once every30 days.
Before refitting the filter ensure that it is
perfectly dry.
Removing the Grease Filters - Fig. 3
a. Remove the pull-out drawer completely.
b. Press the side handles (F) towards the
opposite side and remove the filters.
Putting the Filters Back in Place
a. Remove the pull-out drawer completely
and mount the grease filter so that it
covers the drawer.
b. Closethedrawerandinstalltheremaining
grease filter.
Active Carbon Filter
Thisfiltereliminatestheodoursandvapours
which form during cooking.
Whenusedinnormalconditionsitshouldbe
replaced at intervals of 6-8 months.
Thesefiltercanbeorderedfromthesupplier
The carbon filter cannot be washed or
regenerated.
To dismount the filter proceed as follows:
Pressthetwobuttons C (fig.3),pullthefilter
slightly forwards and remove it.
Attention
Failureto observe therules for cleaningthe
appliance and changing and cleaning the
filters may cause fires.
Therefore, we recommend observing these
instructions.
Fixing the hood
Apply the scheme supplied (Nº 49A) on the
right of the cabinet so that the lines marked
by the arrows match the cabinet ensuring
that they meet at the back and under.
Make two Ø 2 mm holes at points 1 and
2 (fig. 4).
Carry out the same operation on the left.
Fix the hood to the cabinet using screws E
(4,5x16)suppliedwiththeappliance (fig.4).
UsetheshimFsuppliedwiththehoodfor16
mm cupboard side panels.
FittheshimFtotheleftandtotherightofthe
fixing curves of the hood and hook them in
the holes.
Adjusting the removable drawer
The hood may be mounted in cabinets with
different depths.
The back of the drawer can be adjusted so
thatthefrontoftheremovabledraweristhe
same depth as the cabinet.
Proceed as follows: unscrew the screws G,
move the square plates H as required and
tighten the screw G (fig. 5).
Operation
Thehoodmodel JDA 5330isfittedwithtwo
motors.
The speed of the motors is adjusted by
means of a 4-SPEED switch.
Use the high speed switch only in case of
high concentration of vapour.
The hood should be switched ON several
minutesbeforeyoustartcookingandshould
be allowed to run until all the vapours have
been eliminated.
Theswitchingplateisfittedwithtwoswitches
one for continuous adjustment of the
Light switch
Speedswitch

9
Replacing the lamps
— Disconnect the hood from the electricity.
— Opening the Light Cover Support (fig. 6)
a. Remove the pull-out drawer
completely.
b. Push the B knobs inwards toward
each other (in the “Open” direction as
indicated on the plastic knob itself).
— Alwaysreplaceburnt-outlampswitholive
shaped lamps max 40Watts-E14.
— Re-close the light cover support.
— BeforecallingforRepairServicebecause
the hood fails to light up, make sure the
lamp is well-inserted.
Cleaning
Tocleantheoutsideofthehooduseacloth
moistenedwithdenaturedalcoholorneutral
liquid detergents.
Never use products containing abrasive.
Wipe brushed stainless steel in the same
directionasthebrushingtoavoidscratching.

10
ELECTROLUXHAUSGERÄTEGMBH
Rennbahnstraße 72-74
60528 Frankfurt L 921 Ed. 02/97