Jupiter Avionics JA95-N60 User manual

Rev B Page i
JA95-N60 Audio Controller
Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A
Jupiter Avionics Corporation
1959 Kirschner Road
Kelowna BC
Canada V1Y 4N7
Tel: [phone]
Toll-Free: 1 855 478 2232
www.jupiteravionics.com

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev APage ii
Copyright 2022 Jupiter Avionics Corp.
All rights reserved
Jupiter Avionics Corporation (JAC) permits a single copy of this manual to be printed or downloaded for the express use
of an installing agency. Any such electronic or printed copy of this manual must contain the complete text of this copyright
notice. Any unauthorized commercial distribution of this manual is strictly prohibited. Except as described above, no part
of this manual may be reproduced, copied, transmitted, disseminated, downloaded, or stored in any storage medium for
any purpose without the express prior written consent of JAC.
RECORD OF REVISIONS
Revision
Rev Date
Description
ECR
A
Jun 2022
Initial release, Serial number 1001 and higher.
8614
Prepared:
DGB/MPB
Checked:
Approved:
IMPORTANT:
Information in this document is subject to change without notice.
To confirm the current revision status of this manual, visit the JAC website:
www.jupiteravionics.com
JAC
KDV
07-25-22 JAC
MQS
07-25-22

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page iii
Table of Contents
SECTION 1 - DESCRIPTION ................................................................................................................................................. 1
1.1 System Overview .................................................................................................................................................... 1
1.2 Features Overview .................................................................................................................................................. 1
1.3 Inputs and Outputs .................................................................................................................................................. 1
1.3.1 Inputs............................................................................................................................................................... 1
1.3.2 Outputs ............................................................................................................................................................ 1
1.4 Specifications .......................................................................................................................................................... 2
1.4.1 Electrical Specifications................................................................................................................................... 2
1.4.2 Mechanical Specifications ............................................................................................................................... 3
1.4.3 Configuration Connector ................................................................................................................................. 3
1.4.4 Product Configuration Software Version ......................................................................................................... 4
1.4.5 Flammability of Materials ................................................................................................................................ 4
1.4.6 Environmental Specifications .......................................................................................................................... 4
SECTION 2 – INSTALLATION............................................................................................................................................... 5
2.1 Introduction.............................................................................................................................................................. 5
2.2 Continued Airworthiness ......................................................................................................................................... 5
2.3 Unpacking and Inspecting Equipment..................................................................................................................... 5
2.3.1 Warranty .......................................................................................................................................................... 5
2.4 Installation Procedures............................................................................................................................................ 5
2.4.1 Installation Limitations ..................................................................................................................................... 5
2.4.2 Cabling and Wiring .......................................................................................................................................... 5
2.4.3 Mechanical Installation .................................................................................................................................... 6
2.4.4 Legend Replacement ...................................................................................................................................... 6
2.4.5 Post Installation Checks .................................................................................................................................. 6
2.5 Adjustments and Configuration using ProCS™ ...................................................................................................... 6
2.5.1 Configuration Cabling Requirements .............................................................................................................. 7
2.5.2 ProCS™ Setup................................................................................................................................................ 7
2.5.3 Configurable Settings ...................................................................................................................................... 7
2.5.4 Other Configuration Features.......................................................................................................................... 9
2.6 Installation Kit .......................................................................................................................................................... 9
2.6.1 Recommended Crimp Tools ........................................................................................................................... 9
2.7 Installation Drawings ............................................................................................................................................. 10
2.7.1 Generation of Custom Drawings ................................................................................................................... 10
SECTION 3 – OPERATION.................................................................................................................................................. 11
3.1 Introduction............................................................................................................................................................ 11
3.2 System Diagram.................................................................................................................................................... 11
3.3 Front Panel Controls ............................................................................................................................................. 12
(1) Transceiver Switches .................................................................................................................................... 12
(2) Configuration Connector (io) ......................................................................................................................... 12
(3) Transmit Annunciator - TX ............................................................................................................................ 13
(4) Transmit Selector .......................................................................................................................................... 13
(5) AUX Legend .................................................................................................................................................. 13
3.4 Normal Operation Mode ........................................................................................................................................ 13
3.4.1 Panel Lighting................................................................................................................................................ 13
3.4.2 Receiving....................................................................................................................................................... 13
3.4.3 Transmitting (Transmit Operation) ................................................................................................................ 14
3.5 Emergency Operation Mode ................................................................................................................................. 14
3.5.1 Auto Emergency Mode.................................................................................................................................. 14
Appendix A - Installation Drawings.................................................................................................................................. A1
A1 Introduction............................................................................................................................................................ A1
A2 Installation Drawings ............................................................................................................................................. A1
Appendix B - Certification Documents ............................................................................................................................ B1
B1 Airworthiness Approval ......................................................................................................................................... B2
B2 Instructions for Continued Airworthiness .............................................................................................................. B2
B3 Environmental Qualification Form ......................................................................................................................... B3

Rev A Page 1
JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
SECTION 1 - DESCRIPTION
1.1 System Overview
The JA95-N60 Audio Controller - Five Transceiver - Expander - NVG is a compact, lightweight panel that allows
connection of up to 4 additional radios to the aircraft audio system. The JA95-N60 is compatible with the transceiver
connections of any of Jupiter’s JA9x series of audio controllers as well as any civil aviation audio controller.
The JA95-N60 is set up on a per-installation basis using a configuration cable and a PC running the product
configuration tool to download system configuration settings via the configuration connector (io) without the necessity
of removing the unit from the panel. To facilitate future customizations and certification, no software or complex
electronic devices are used in the JA95-N60 design.
1.2 Features Overview
Many of the JA95-N60 input and output levels are adjustable, and several audio paths are selectable.
A configuration connector is provided on the faceplate of the JA95-N60 for configuration of audio levels and routing.
The JA95-N60 has two modes of operation: Normal Mode and Emergency Mode.
The JA95-N60 supports up to five transceivers, each selectable from a rotary switch.
The JA95-N60 allows transmit access for one audio panel.
The JA95-N60 has NVIS Green A Legends and Annunciators.
1.3 Inputs and Outputs
Refer to the JA95-N60 connector maps for the mating connector designators and pin assignments for the
input and output signals.
1.3.1 Inputs
Name
Qty
Type
CONFIG DATA TO JA95
1
Data signal
LIGHTS INPUT
1
Analog control signal
TX MIC HI/LO
1
Audio signal
MODE SELECT
1
Multi format signal
TX PTT INPUT
1
Active low discrete (Feature selected from ProCS)
POWER INPUT
1
14 to 28 Vdc power supply
RX HI/LO
5
Audio signal
1.3.2 Outputs
Name
Qty
Type
CONFIG DATA FROM JA95
1
Data signal
MIC HI/LO
5
Audio signal
TX PTT 5 Active low discrete
(PA PTT feature selected from ProCS)
RX OUTPUT HI/LO
1
Audio signal (Feature selected from ProCS)

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 2
1.4 Specifications
1.4.1 Electrical Specifications
Power Input
Primary nominal voltage 28 Vdc
Secondary nominal voltage 14 Vdc
Maximum voltage 32.2 Vdc
Minimum voltage 10.2 Vdc
Emergency voltage 9.0 Vdc
Input current at 28 Vdc ≤ 0.7 A
Input current at 14 Vdc ≤ 1.4 A
Input current at 9 Vdc ≤ 2.4 A
1.4.1.1 Audio Performance
Rated Input Level
Microphone input level 250 mVrms ±10%
Rated Output Level
RX rated output 7.75 Vrms±10%
RX rated output,
in emergency mode or with power input ≤6 Vdc 2.10 Vrms±10%
Microphone rated output 250 mVrms±10%
Audio Frequency Response
Audio output audio frequency response ≤3dB from 300 to 6000 Hz
Spurious Responses
Audio output spurious response attenuation ≥50 dB
Distortion Characteristics
Audio output distortion at rated power ≤10%
Input Impedance
Microphone input Impedance 150 Ω±10%
Receive Audio input Impedance 1000 Ω±10%
Output Impedance
RX output Impedance ≤60 Ω
Transceiver Microphone output Impedance ≤80 Ω
Output Load
RX Output load 600 Ω±10%
Transceiver Microphone load 150 Ω±10%
Input to output Crosstalk and Bleed-through Level
Input to Output crosstalk ≤55 dB
Input to Input Crosstalk Level
Input to Input crosstalk ≤60 dB

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 3
Input to Microphone Output Crosstalk.
Input to Microphone Output crosstalk ≤1.0 mV
Audio Noise Level without Signal
Noise level below the rated output ≥60 dB
Listening Test Loud and Clear
1.4.1.2 Audio Performance, Other
RECEIVE AUDIO input circuitry type differential
RX output HI / LO output circuitry type single ended
MIC output circuitry type differential
1.4.1.3 Discrete Signals
Active low control input, active signal level ≤+3 Vdc
Active low control input, inactive signal level ≥+10 Vdc
Active low control input, active signal level 0.1 to 10 mA
Active low control input signals have internal pull-up resistor
Active low control output, active output ≤+2 Vdc
Active low control output active signal sinks ≤1 Adc
1.4.1.4 Lights Input
LIGHTS INPUT ranges 0 to 28, 0 to 14 and 0 to 5 Vdc
LIGHTS INPUT current 10 mA max.
1.4.2 Mechanical Specifications
Height 1.875 in [47.6 mm] max
Behind panel depth 5.48 in [139 mm] max
Faceplate width 5.75 in [146 mm]max
Behind panel width 5.00 in [127 mm]max
Weight 1.64 lb [0.74 kg] max
Material brushed aluminum with conversion
coating
Connectors (4): J1 One 37-pin D-Sub male
J2 One 50-pin D-Sub male
J3 One 4 pole 3.5mm stereo jack
J4 One 4-40 stud, 0.5 in max
Mounting 4 Dzus fasteners
Bonding ≤2.5 mΩ
Installation kit part number INST-JA95
1.4.3 Configuration Connector
The JA95-N60 configuration connector communication standard for CONFIG DATA TO JA95 data input signal and
CONFIG DATA FROM JA95 data output signal is RS-232.

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 4
1.4.4 Product Configuration Software Version
Configuration of the JA95-N60requires the Product Configuration Software (ProCS) version v0.70.1or later. Refer
to the release notes from https://www.jupiteravionics.com/productsoftware.php or contact Jupiter Avionics to ensure
the correct version is used.
1.4.5 Flammability of Materials
The JA95-N60 complies with the requirements of RTCA/DO-160G Sec 26.3.3 "Flammability", through equivalent
flammability testing of materials and the Small Parts Exemption.
1.4.6 Environmental Specifications
The JA95-N60 Audio Controller - Five Transceiver - Expander - NVG has been qualified to the environmental
conditions listed below. Environmental categories for which TSO compliance has been demonstrated are listed in the
Environmental Qualification Form in Appendix B of this manual.
Temperature:
Operating -45 °C to +70 °C
Ground Survival -55 °C to +85 °C
Altitude 50,000 ft
Humidity Cat A (48 hours)
Shock, Crash Safety 6 g, 20 g for 11 ms

Rev A Page 5
JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
SECTION 2 – INSTALLATION
2.1 Introduction
This section contains unpacking and inspection procedures, installation information, and post-installation checks.
2.2 Continued Airworthiness
Maintenance of the JA95-N60 is on condition only. Scheduled inspection and/or periodic maintenance of this unit is
not required.
2.3 Unpacking and Inspecting Equipment
Unpack the equipment carefully. Check for shipping damage and report any problems to the relevant carrier. Confirm
that the Authorized Release Certificate or Certificate of Conformance is included. Complete the on-line warranty card
from the Jupiter Avionics Corporation (JAC) website - www.jupiteravionics.com/warranty
2.3.1 Warranty
This product manufactured by JAC is warranted to be free of defects in workmanship or performance for 2 years from
the date of installation by an approved JAC dealer or agency. This warranty covers the cost of all materials and labour
to repair or replace the unit, but does not include the cost of transporting the defective unit to and from JAC or its
designated warranty repair centre, or of removing and replacing the defective unit in the aircraft. This warranty does
not cover failures due to abuse, misuse, accident, or unauthorized alteration or repairs.
THIS WARRANTY IS VOID IF THE PRODUCT IS NOT INSTALLED BY AN AUTHORIZED JAC DEALER. If the on-
line warranty card is not completed, the product will be warranted from the date of manufacture.
Contact JAC for return authorization, and for any questions regarding this warranty and how it applies to your unit(s).
JAC is the final arbiter concerning warranty issues.
2.4 Installation Procedures
WARNING: Loud noise can cause hearing damage. Set the headset volume to minimum before
conducting tests, and slowly increase the volume to a comfortable listening level.
CAUTION: The power input circuitry of the unit may be damaged if the installation does not conform to the
wiring instructions in this manual.
2.4.1 Installation Limitations
The conditions and tests for CAN TSO approval of the JA95-N60 are minimum performance standards. Those
installing the JA95-N60, on or in a specific type or class of aircraft, must determine that the aircraft installation
conditions are within TSO standards. The JA95-N60 may be installed only by following the applicable airworthiness
requirements.
2.4.2 Cabling and Wiring
All wire shall be selected in accordance with the original aircraft manufacturer’s maintenance instructions, or AC43.13-
1B Change 1, Paragraphs 11-76 through 11-78. Unshielded wire types shall qualify to MIL-W-22759 as specified in
AC43.13-1B Change 1, Paragraphs 11-85, 11-86, and listed in Table 11-11. For shielded wire applications, use Tefzel
MIL-C-27500 shielded wire with tag ring or equivalent (for shield terminations) to make the most compact and easily
terminated interconnect. Follow the Connector Map in Appendix A of this manual.

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 6
Allow 3” from the end of the shielded wiring to the shield termination to allow the connector hood to be easily installed.
Refer to the Interconnect drawing in Appendix A of this manual for shield termination details. Note that this unit has a
‘clamshell’ hood that is installed after the wiring is complete.
Maintain wire segregation and route wiring in accordance with the original aircraft manufacturer’s maintenance
instructions.
Unless otherwise noted, all wiring shall be a minimum of 24 AWG, except power and ground lines, which shall be a
minimum of 22 AWG. Refer to the Interconnect drawing for additional specifications. Check that the ground
connection is clean and well secured, and that it shares no path with any electrically noisy aircraft accessories such
as blowers, turn-and-bank instruments, or similar loads.
2.4.3 Mechanical Installation
The JA95-N60 can be mounted in any attitude and location with adequate space for the front panel and sufficient
clearance for the connector and wiring harness. It requires no direct cooling.
2.4.4 Legend Replacement
The JA95-N60 NVIS Green A compliant illuminated legends are field replaceable. For further information, refer to the
‘Legend Replacement’ document in Appendix A of this manual.
2.4.5 Post Installation Checks
2.4.5.1 Voltage/Resistance checks.
Do not attach this unit until the following conditions are met:
a) Check P1 pin 19 for lights buss voltage.
b) Check P2 pin 17 for +28 Vdc or +14 Vdc relative to ground.
c) Check P2 pin 34 for continuity to ground (less than 0.5 Ω).
d) Check all pins for shorts to ground or adjacent pins.
2.4.5.2 Configuration
Ensure that the JA95-N60 contains the correct configuration settings. This may be done at the factory, on the
maintenance bench or in the aircraft before the power on checks are performed. Refer to section 2.5.1.
2.4.5.3 Power on Checks.
Power up the aircraft’s systems and confirm normal operation of all functions of the JA95-N60. Refer to
Section 3 (Operation) for specific operational details.
a) Confirm radio operation for both receive and transmit. Check yoke or cyclic switch action. Check the radio
selection and inputs. Do not proceed until the radios are functioning correctly.
b) Unusual buzzes, hums or other background audio are symptomatic of multiple grounds, or noisy external
systems such as blowers or pumps sharing wiring with the audio system. If a transmitter fails to key or
correctly modulate it is often the result of not connecting all required grounds to the radio or external audio
system.
c) Check the Emergency operation.
d) Check that all configurations settings are correct.
When all performance checks are satisfied, complete the necessary regulatory documentation before releasing the
aircraft for service. Refer to Appendix B.
2.5 Adjustments and Configuration using ProCS™
All the JA95-N60 internal adjustments are set from the Product Configuration Software ProCS™. Configuration data is
sent to the JA95-N60 via the front panel connector (io), using the Configuration Cables and a computer running the
ProCS™ software. For configuration requirements, see section 2.5.1.

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 7
For full information on the configuration process, and for installation of ProCS™ on your computer, refer to the
ProCS™ manual on the Jupiter Avionics website - www.jupiteravionics.com/productsoftware.
2.5.1 Configuration Cabling Requirements
To configure the JA95-N60, it is necessary to load the Product Configuration Software ProCS™ onto a Windows-
based computer as described in the ProCS™ manual.
The cables required to configure the JA95-N60 are not included with the unit.
Quantity Description JA95-N60
1 USB A to RS232 9-Pin Cable CAB-USB-0002
1 Configuration Cable JA99-001
2.5.2 ProCS™ Setup
The ProCS™ JA95-N60 menu item 'ProCS Setup' provides a drawing showing the cabling arrangement for
connecting the JA95-N60 to a computer running the ProCS™.
2.5.3 Configurable Settings
A standard unit is shipped from the factory with all internal adjustments configured to the default levels. At installation,
it may be desirable to change some of these settings to suit the local operating environment.
Note: To properly configure the JA95-N60, power must be applied to the unit.
Within ProCS™, the configurable settings are grouped together into the following sections:
2.5.3.1 Front Panel Switches
The Front Panel Switches window is used to specify the text for each legend.

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 8
2.5.3.2 Radios
2.5.3.3 Receive Levels
2.5.3.4 Transmit Levels
The Transceiver MIC output signals can be adjusted from
0.010 to 1.000 Vrms. (Default 250 mVrms)
The Radios window is used to define the
radios for the transceivers.
The receive level of each of the RX inputs can be
adjusted from 1 to 10 Vrms.
(Default 7.75 Vrms)
When the Transmit Timeout check box is checked the
transmit time-out is enabled (Default not checked)

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 9
2.5.3.5 Sidetone Levels
2.5.3.6 Audio Muting
2.5.3.7 Lighting Voltage Selection
2.5.4 Other Configuration Features
In the JA95-N60 Product Information Window, the model number, serial number and check sum of the JA95-N60
Audio Controller - Five Transceiver - Expander - NVG can be viewed.
2.6 Installation Kit
The kit required to install this unit is not included with the unit.
The installation kit (Part # INST-JA95) consists of the following:
Quantity Description JAC Part #
2 TAG ring CON-5500-0625
1 D-Sub 37-pin connector, hood and 37 crimp pins CON-3420-0037
1 D-Sub 50-pin connector, hood and 50 crimp pins CON-3420-0050
2 Heat Shrink Tubing WIR-HTSK-1000
2.6.1 Recommended Crimp Tools
Standard D-Sub Crimp Tool Chart
Tool Type
Hand crimping tool
Positioner
Insertion/extractor tool
POSITRONIC
9507-0-0-0
9502-5-0-0
4711-2-0-0
DANIELS
AFM 8
K13-1
91067-2
MIL-SPEC
M22520/2-01
M22520/2-08
M81969/1-02
The Receive Sidetone Level can be adjusted from 0 to -12 dB
of the rated phone Level. (Default -6 dB)
To select Audio Muting during Transmit, check the box as shown.
The lights input may be +5 Vdc, +14 Vdc or +28Vdc
(Default +28 Vdc).

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 10
2.7 Installation Drawings
The drawings and documents required for Installation can be found in Appendix A of this manual.
2.7.1 Generation of Custom Drawings
The interconnects and connector maps in Appendix A of this manual are generic drawings based on the standard
version of the JA95-N60. However, if a unit has been configured using JAC’s ProCS™ software to change switch
legends or lighting voltages, the software can be used to generate fully customized interconnects and connector
maps for use by the installer.

Rev A Page 11
JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
SECTION 3 – OPERATION
3.1 Introduction
This section contains the system diagram and operating instructions for the JA95-N60.
3.2 System Diagram
The JA95-N60 Audio Controller - Five Transceiver - Expander - NVG is a compact, lightweight panel that allows
connection of up to 4 additional radios to the aircraft audio system. The JA95-N60 is compatible with the transceiver
connections of any of Jupiter’s JA9x series of audio controllers as well as any civil aviation audio controller.
The text on the JA95-N60 legend (shown here as AUX) should be selected to match the text on the main panel
legend representing the expanded transceiver position.

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 12
3.3 Front Panel Controls
Note: The NVIS Green A compatible legends and deadfront annunciator are removable and may be
replaced with custom ordered parts. The controls will be referred to by the default legend and annunciator
names as shown below.
1. Transceiver switches and associated legends
2. Music/configuration input connector and legend
3. Transmit annunciator (deadfront)
4. Transmit selector
5. AUX Legend
(1) Transceiver Switches
These are five white two-position toggle
switches. When a switch is set to the ‘up’
position, audio from the associated
transceiver is routed to the phones.
The legends (above the switches) are
interchangeable to allow customization.
(Default – AUX1, AUX2, AUX3, AUX4, AUX5.)
(2) Configuration Connector (io)
This connector is used during installation to change configuration settings.
CAUTION:
Attempting to connect an incompatible plug or device could damage the unit , the attached
device, or both. If in doubt, check with your installing agency.
1
2
3
4
5

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 13
(3) Transmit Annunciator - TX
This is a deadfront annunciator that will illuminate when
the JA95-N60 is transmitting.
The default legend is ‘TX’, but it is interchangeable to allow customization.
(4) Transmit Selector
This is a rotary six-position control that is used to
select transmission via one of the five transceivers.
Each of the transmit selector positions is linked by a
white line to the corresponding transmit select
annunciator, transceiver switch and legend.
The appropriate annunciator will light green to show
which transceiver is selected for transmit –
‘AUX3’ in this example.
Note: Transmission on any of the transceivers linked to the JA95-N60 is only possible if the designated
transceiver (AUX in these examples) is selected on the main audio panel.
(5) AUX Legend
This is a customizable legend that is intended to remind the
operator which transceiver on the main audio panel must be
selected to allow transmission on the JA95-N60 Expander - NVG
Panel.
The default legend is ‘AUX’, but it is interchangeable to allow customization to match the legend on the main audio
panel.
3.4 Normal Operation Mode
Note: Numbers in parentheses refer to the front panel controls shown in section 3.2.
The JA95-N60 is in Normal mode when suitable electrical power is supplied to the unit.
3.4.1 Panel Lighting
The legends and annunciators will be illuminated (when appropriate) and dim through the aircraft lighting buss.
3.4.2 Receiving
Note: Transmission on any of the transceivers linked to the JA95-N60 is only possible if the designated
transceiver (AUX in these examples) is selected on the main audio panel.
When the JA95-N60 receives an incoming transmission on a transceiver or receiver that has been selected, either by
the white transceiver receive switches (1) or the transmit selector (4), the incoming audio will be directed to the user’s
phones.

JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Rev A Page 14
3.4.3 Transmitting (Transmit Operation)
Note: Transmission on any of the transceivers linked to the JA95-N60 is only possible if the designated
transceiver (AUX in these examples) is selected on the main audio panel.
To select a transceiver, rotate the Transmit Select Switch until it aligns with the line leading to the Transceiver Select
switch legend (see 1) - default legends AUX1, AUX2, AUX3, AUX4, or AUX5. The corresponding Transmit Select
annunciator will illuminate.
When the TX PTT input is activated, the unit will transmit on the selected transceiver, and the deadfront Transmit
Annunciator (3) will illuminate ‘TX’. All MIC and sidetone audio will be routed to the RX OUTPUT.
3.5 Emergency Operation Mode
Emergency mode is entered automatically if power to the unit is lost.
3.5.1 Auto Emergency Mode
If the unit is in emergency mode because power has been lost to the unit, the AUX1 transceiver will be routed to the
RX OUTPUT. The TX microphone and TX transmit key are connected to the AUX1 transceiver. No other function in
the JA95-N60 will operate when power is lost. All indicator LEDs, legends and annunciators will be dark.

Rev A Page A1
JA95-N60 Audio Controller - Five Transceiver - Expander - NVG
Installation and Operating Manual
Appendix A - Installation Drawings
A1 Introduction
The drawings necessary for installation and troubleshooting of the JA95-N60 Audio Controller - Five Transceiver -
Expander - NVG are in this Appendix, as listed below.
Note: A fully customized set of Connector Maps and Interconnects can be created using the ProCS software.
Refer to the ProCS™ manual for further information.
A2 Installation Drawings
DOCUMENT Rev
JA95-N60 Connector Map A
JA95-N60 Interconnect A
JA95-N60 Mechanical Installation A
JA95-N60 Equipment Block Diagram A
Reference Documents
TOL-CUST-EXTR Legend Replacement A

JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT
TITLE
APPROVED
PREPARED
CHECKED
L00N3
NCAGE CODE PART NO. SHEET
DOC NO.
CONFIDENTIAL & PROPRIETARY
TO JUPITER AVIONICS CORP.
Audio Controller - Five Transceiver - Expander - NVG
P1 Connector Map
JA95-N60 1/3
JA95-N60 Connector Map Rev A.dwg
TAT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
18 19
36 37
SPARE 1 AUX 1 RX HI AUX 2 RX HI AUX 3 RX HI AUX 4 RX HI AUX 5 RX HI SPARE 2 SPARE 3 SPARE 4 SPARE 5 SPARE 6 SPARE 7 SPARE 8 SPARE 9 SPARE 10 SPARE 11 SPARE 12 RX OUTPUT HI LIGHTS INPUT
SPARE 13 AUX 1 RX LO AUX 2 RX LO AUX 3 RX LO AUX 4 RX LO AUX 5 RX LO SPARE 14 SPARE 15 SPARE 16 SPARE 17 SPARE 18 SPARE 19 SPARE 20 SPARE 21 SPARE 22 SPARE 23 SPARE 24 RX OUTPUT LO
P1
37 PIN FEMALE DMIN
MATING CONNECTOR
COM RX
RECEIVE CONNECTOR
VIEW IS FROM REAR OF MATING CONNECTOR

JUPITER AVIONICS TEMPLATE AUTOCAD PORTRAIT SIZEA REV B.DWT
TITLE
APPROVED
PREPARED
CHECKED
L00N3
NCAGE CODE PART NO. SHEET
DOC NO.
CONFIDENTIAL & PROPRIETARY
TO JUPITER AVIONICS CORP.
Audio Controller - Five Transceiver - Expander - NVG
P2 Connector Map
JA95-N60 2/3
JA95-N60 Connector Map Rev A.dwg
TAT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
AUX 1 PTT
AUX 1 MIC HI AUX 1 MIC LO AUX 2 MIC HI AUX 2 MIC LO AUX 3 MIC HI AUX 3 MIC LO AUX 4 MIC HI AUX 4 MIC LO AUX 5 MIC HI AUX 5 MIC LO SPARE 11 SPARE 12 TX MIC HI TX MIC LO SPARE 13 SPARE 14 SPARE 15 SPARE 16 SPARE 17 SPARE 18 SPARE 19 SPARE 20 SPARE 21 SPARE 22 SPARE 23 SPARE 24 SPARE 25 SPARE 26 SPARE 29 SPARE 30
AUX 2 PTT AUX 3 PTT AUX 4 PTT AUX 5 PTT SPARE 1 SPARE 2 SPARE 4 SPARE 3 SPARE 5 SPARE 6 SPARE 7 SPARE 8 SPARE 9 SPARE 10 POWER INPUT
POWER GROUND
P2
50 PIN FEMALE DMIN
MATING CONNECTOR
PTT OUT
MIC OUT
VIEW IS FROM REAR OF MATING CONNECTOR
SPARE 27 SPARE 28
TRANSMIT CONNECTOR
TX PTT INPUT