Jura Z6 User manual

Z6 – Quick Reference Guide

2
Z6 – Quick Reference Guide
Z6 – Quick Reference Guide
J
These short instructions do not replace the ‘Z6 Instructions for Use’.
Make sure you read and observe the safety information and war-
nings first in order to avoid hazards.
You can initiate the rinse operation manually at any time.
Precondition: ‘Please select product’ is displayed.
TPlace a receptacle under the dual spout.
TPress the Rotary Switch.
‘Maintenance status’
TPress the Rotary Switch.
‘Clean’
TTurn the Rotary Switch until ‘Rinse’ is displayed.
TPress the Rotary Switch to initiate the rinse operation.
‘Machine is rinsing’, ‘Milk system is being rinsed’, water
flows out of the dual spout.
The rinse stops automatically. ‘Please select product’
appears on the display.
15 minutes after milk preparation, the milk system is automatically
rinsed. Therefore always place a receptacle under the dual spout
after preparing milk.
15 minutes after milk preparation, ‘Milk system is being rinsed’
appears, water flows out of the dual spout. The rinse stops automa-
tically. Your Z6 is once more ready for use.
To ensure that the milk system in the dual spout always works pro-
perly, you must clean it daily when you have been preparing milk.
Rinsing the machine
Automatic milk system
rinsing
Cleaning the milk system

3
Z6 – Quick Reference Guide
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EJURA milk system cleaner is available from specialised dealers.
ETo clean the milk system, use the container supplied.
Precondition: ‘Clean the milk system’ is displayed.
TPress the Rotary Switch.
‘Clean the milk system’
TPress the Rotary Switch again.
TPress the ‘Start’ button.
TPress the ‘Start’ button again.
‘Cleaning agent for milk system’
TRemove the milk pipe from the milk container or carton.
TAdd 1 capful of milk system cleaner to the outer, rectangular
part of the container.
TPlace the container under the dual spout.
TConnect the milk pipe to the container.
ETo connect the milk pipe to the container correctly, the pipe
must be fitted with a connector.
TSlide the dual spout down to fix the container in place.
TPress the ‘Next’ button.
‘Milk system is being cleaned’, the dual spout and the pipe
are cleaned. Water flows out of the dual spout.
The operation stops automatically. ‘Milk system cleaning
complete’ appears briefly on the display.
The dual spout must be dismantled and rinsed daily if milk has been
prepared to make sure it functions perfectly and also in the interests
of hygiene.
CAUTION

4
Z6 – Quick Reference Guide
TRemove the milk pipe and rinse it thoroughly under running
water.
TPress the releasing devices and pull the cover of the dual
spout up and off.
TRemove the milk system from the dual spout.
TDismantle the milk system into its individual parts.
TRinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250 ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
TReassemble the milk system.

5
Z6 – Quick Reference Guide
TFit the assembled individual parts back in the dual spout and
press it firmly.
TFit the cover of the dual spout. Make sure the cover of the
dual spout is correctly fitted.
TConnect the milk pipe to the dual spout.
Your Z6 no longer has to be descaled if you are using the CLARIS
Smart filter cartridge. If you did not insert the filter cartridge the first
time you used the machine, you can do this now as follows.
Precondition: ‘Please select product’ is displayed.
TRemove and empty the water tank.
TFit the filter cartridge extension supplied on top of a CLARIS
Smart filter cartridge.
TInsert the filter cartridge with its extension into the water
tank.
TTurn the filter cartridge clockwise until it audibly clicks into
place.
TFill the water tank with fresh, cold water and reinsert the
tank.
EThe machine automatically detects that you have just inserted
the filter cartridge.
‘Use filter’ / ‘Saved’
‘Filter is being rinsed’, the filter is rinsed. The water flows
directly into the drip tray.
Inserting the filter

6
Z6 – Quick Reference Guide
‘Empty drip tray’
TEmpty the drip tray and put it back into the machine.
‘Use filter’, ‘Filter rinsing complete’
‘Please select product’ appears on the display. Your Z6 is
once more ready for use.
EOnce the filter cartridge stops working (depending on the
water hardness setting), the Z6 will prompt you to change the
filter.
ECLARIS Smart filter cartridges are available from specialised
dealers.
Precondition: ‘Change filter’ is displayed.
TPress the Rotary Switch.
‘Change the filter’
TPress the Rotary Switch again.
TRemove and empty the water tank.
TTurn the filter cartridge anticlockwise and remove it along
with the extension from the water tank.
TFit the filter cartridge extension on top of a new CLARIS
Smart filter cartridge.
TInsert the filter cartridge with its extension into the water
tank.
TTurn the filter cartridge clockwise until it audibly clicks into
place.
TFill the water tank with fresh, cold water and reinsert the
tank.
EThe machine automatically detects that you have just chan-
ged the filter cartridge.
‘Change the filter’ / ‘Saved’
Changing the filter

7
Z6 – Quick Reference Guide
‘Filter is being rinsed’, the filter cartridge is rinsed. The water
flows directly into the drip tray.
‘Empty drip tray’
TEmpty the drip tray and put it back into the machine.
‘Change the filter’, ‘Filter rinsing complete’
‘Please select product’ appears on the display. Your Z6 is
once more ready for use.
After 180 preparations or 80 switch-on rinses, the Z6 will prompt you
to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
EThe cleaning programme lasts approximately 20 minutes.
EDo not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EJURA cleaning tablets are available from specialised dealers.
Precondition: ‘Clean machine’ is displayed.
TPress the Rotary Switch.
‘Clean’
TPress the Rotary Switch again.
‘Clean’
TPress the ‘Start’ button.
TPress the ‘Start’ button again.
‘Empty coffee grounds container’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Press the Rotary Switch’
TPlace a receptacle under the dual spout.
TPress the Rotary Switch.
‘Machine is being cleaned’, water flows out of the dual spout.
The operation is interrupted, ‘Add cleaning tablet’.
TOpen the cover of the filler funnel for ground coffee.
Cleaning the machine
CAUTION

8
Z6 – Quick Reference Guide
TInsert a JURA cleaning tablet into the filler funnel.
TClose the cover of the filler funnel.
‘Press the Rotary Switch’
TPress the Rotary Switch.
‘Machine is being cleaned’, water flows out of the dual spout
repeatedly.
The operation stops automatically.
‘Empty coffee grounds container’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Please select product’ appears on the display. Cleaning is
now complete.
The Z6 builds up deposits of limescale over time and automatically
prompts you to descale it when necessary. The degree of calcifica-
tion depends on the hardness of your water.
EIf you are using a CLARIS Smart filter cartridge, you will not be
prompted to descale.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
TAvoid contact with the skin or eyes.
TRinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dama-
ged and/or traces could be left behind in the water.
TUse only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
TAllow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
TClean up any splashes immediately.
Descaling the machine
JCAUTION
CAUTION
CAUTION
CAUTION

9
Z6 – Quick Reference Guide
EThe descaling programme lasts approximately 45 minutes.
EJURA descaling tablets are available from specialised dealers.
Precondition: ‘Decalcify machine’ is displayed.
TPress the Rotary Switch.
‘Descale’
TPress the Rotary Switch again.
‘Descale’
TPress the ‘Start’ button.
TPress the ‘Start’ button again.
‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Pour descaling agent into water tank’
TRemove and empty the water tank.
TCompletely dissolve the contents of one blister (3 JURA des-
caling tablets) in a receptacle holding 600 ml of lukewarm
water. This may take several minutes.
TPour the solution into the empty water tank and insert it into
the machine.
‘Press the Rotary Switch’
TPlace a receptacle under the hot water spout.
TPress the Rotary Switch.
‘Machine is being descaled’, water flows out of the hot water
spout repeatedly.
The operation is interrupted, ‘Empty drip tray’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’

10
Z6 – Quick Reference Guide
TEmpty the receptacle and place it under the hot water and
dual spouts.
TRemove the water tank and rinse it thoroughly.
TFill the water tank with fresh, cold water and reinsert the
tank.
‘Press the Rotary Switch’
TPress the Rotary Switch.
‘Machine is being descaled’, the descaling operation is con-
tinued, water flows out of the dual spout and the hot water
spout.
‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Please select product’ appears on the display. Descaling is
now complete.
EIf the descaling operation stops unexpectedly, rinse the water
tank thoroughly.