Justwise 633/7863 User manual

633/7863
Assembly Instructions – Please keep for future reference
Important – Please read these instructions fully before starting assembly
Dimensions
Length - 200cm
Width - 142.5cm
Height - 185cm
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 02/11/11
Double High Sleeper Bunk Bed

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
1
Important
1) Please note the maximum mattress height is indicated on the corner post inside the opening at the
top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.
3) Maximum thickness of the mattress is 20cm: The top of the mattress shall not come above the line
marked on the bed.
4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are
loose.
5) Recommended size of the mattress for the top bunk is 135×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) The upper bed of bunk beds are not suitable for children under six years due to the risk of injury
from falls.
8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or
hung on a bunk bed.
Warning
1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance
between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2007
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Place the product on flat and
steady surface during use.
• Keep these instructions for
further use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing points
be fully tightened.
Mattress height safety notice
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Dispose of all packaging
carefully and responsibly.
• Safety: To avoid any risk of
suffocation to animals or
children dispose of the plastic
bags immediately.
• From time to time check that
there are no loose screws on
this unit.
• Cleaning: As with all surfaces
clean with a damp cloth and
mild detergent, do not use
bleach or abrasive products.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

Please check you have all the parts listed below
Components - Parts
2
1Corner post x 2 (Ø4.5 x 184.7cm)
2Corner post x 2 (Ø4.5 x 184.7cm)
3End panel x 2 (141.9 x 39.8cm)
4Lower stretcher (short) x 2 (2 x 133.9cm)
Rear guard (191 x 42cm)
6
Lower stretcher (long) (190.4 x 3cm)
7
8Front guard (191 x 42cm)
5Side support x 2 (Ø1.9 x 134.3cm)
9Rear support x 2 (Ø1.3 x 90cm)
10 Central support (193.5 x 6.4cm)
11 Ladder (151 x 35.7cm)
12 Lower bed slats (with hole) x 4(1.6 x140cm) 13 Lower bed slats x 20 (1.6 x 140cm)
If you have damaged or missing components,
call the Customer Helpline: 08456 400800

Components - Fittings
0
Ruler – Use this ruler to help correctly identify the screws
510 2015 4035
30
25 80
75
7060 65
45 50 55 160155150140 145120 125 130 135
85 90 10095 115110105 165 170
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
3
ABC
D E F
GHJ
K L M
OP
M6 x 15mm Allen screw x 12 M6 x 65mm Allen screw x 9 Curved washer(small) x 19
M6 x 45mm Screw x 4 M8 x 65mm Allen screw x 4
M6 x 35mm Allen screw x 2 M6 x 10mm Screw x 56
Plastic cap x 4 Curved washer(large) x 8 Rubber washer x 8
Nut x 10
Plastic plug x 2 Allen key x 2 Allen key x 1
N
M6 x 25mm Screw x 4

Step 1
Assembly Instructions
Assembling side frames
4
Lay corner posts and
, end panel , side
support and short
lower stretcher flat on
the floor as shown.
Note: The holes in end
panel must be at the
top.
Insert end panel into
the large holes in posts
and .
Secure using fixings
and .
Note: Do not fully
tighten screws .
Assemble side support
in between the corner
posts using screws .
Note: Do not fully tighten
screws .
Assemble short lower
stretcher in between
the corner posts using
fixings and .
Note: Do not fully
tighten screws .
Insert end caps into
the top of the corner
posts.
Repeat for the other side
frame.
1
Note: Hole at top
1
3
AC
D
3
4
3
3
1
A
C
A
4
B
B
D
C
1
2
3
4
5
AC
D
BC
Top
Bottom
L
2
5
2
5
L
L
L

Step 2
Assembling rear guard
and stretchers
5
HE
BC
JE
BC
BC
JE
HE
G
F
F
2
6
2
2
6
79
7
L
9
9
L
L
Two people are needed
here.
With help, stand both
side frames upright.
Assemble rear guard
in between the side
frames as shown.
Note: Do not fully tighten
any screws during the
assembly.
Secure at the top using
fixings and as
shown.
Secure at the bottom
using fixings
and as shown.
Note: Plastic washers
are located in between
the rear guard and the
side frames.
Assemble long lower
stretcher in between
the side frames using
fixings and .
Assemble rear supports
in between rear guard
and long stretcher
using screws .
6
B C
E F G H
J
F
B C
L
7
9
67
G
F
Assembly Instructions

Step 3
Assembling front guard
and central support
At this stage, choose if
you want the ladder on
the right hand side or left
hand side.
According to which side
you want the ladder,
assemble front guard
in between the side
frames as shown.
Secure at the top using
fixings and .
Secure at the bottom
using fixings
and .
Assemble central support
in between the side
frames using fixings
and .
Note: Ensure the ends
of the central support
bend ‘up’ as shown!
6
8
E F G H
J
BC
CB
EJ
EH
F
G
8
1
F
Alternative
assembly
8
CB
EJ
EH
F
F
G
1
10
J
A
J
A
3
10
3
A
J
10
10
A
J
10
End to bend up!
End to bend up!
Assembly Instructions

Step 4
7
Assemble ladder to
front guard using
fixings and .
Note: fixings are
located inside the frame
as shown.
Attaching ladder
11
J
C K
8
J
J
K
C
11
8
J
K
C
11
8
Assembly Instructions

Step 5
Assembling slats
(with holes)
8
Assemble slats in the
locations shown, using
screws and .
Note: Screws are
used at each end.
Screws secure into
central support in the
middle.
12
L
L
M
L
8
12
12
8
M
12
10
10
M
L
M
10
Assembly Instructions
L
L
L
L
L
L
L
M
M
M

Step 6
Assembling slats
Assembly is complete.
9
Assemble slats using
screws as shown.
Plastic plugs can be
used to cover the un-used
holes in corner posts
as shown.
13
N
L
1
L
13
8
N
N
N
N
13 L
1
1
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Justwise Group LTD., 6 The Shires, Shire Hill Industrial Estate, Saffron Walden Essex. CB11 3AP