Justwise Boston 833/1757 Datasheet

Boston Tall Unit with Mirror
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 36.5cm
Depth - 36.5cm
Height - 171.5cm
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
833/1757
Issue 2 - 21/04/11

1
Safety and Care Advice
-
Please read these instructions fully before starting assembly
Important
Clean using a damp cloth or a
proprietary domestic furniture
polish. Do not use abrasive
cleaners.
This product should not be
discarded
with household waste.
Take to your local authority waste
disposal only.
Care and maintenance
From time to time check that
there are no loose screws on
this unit.
It is essential that this unit is
securely fixed to a wall!
Installation should only be
carried out by a competent
person, using suitable tools in a
safe manner.
Wall fixing
Before securing this item to the
wall, please ensure the fixings
you intend to use are suitable
for your wall type, and will
safety secure the weight of the
unit, plus any future contents.
Please be reminded of the
dangers that may arise, if it is
not correctly installed.
Keep these instructions for
future use.
Dispose of all packaging
carefully and responsibly.
Do not use this item if any
components are missing or
During assembly children
should be kept away from the
product due to possible risk of
injury.
damaged.
Check you have all the
components and tools listed
on page 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Do not stand or put excessive
weight on the product, this
could cause damage.
Parts of the assembly will be
easier with 2 people.
To ensure an easier assembly,
we strongly advise that all fittings
are only finger tightened during
initial assembly. Only upon
completion of the assembly
should all fixing points be fully
tightened.
We do not
recommend the
use of power
drill/drivers for
inserting screws.
as this could damage the unit.
Only use hand screwdrivers.
Glass safety
This product complies with
BS7449: 1991
Product stock ref: BK101M
The glass used with this product is annealed mirror glass of a
nominal thickness of 3 mm. It is not required to comply with BS 6206.
If a glass component is chipped or broken, replace with glass of the
type described on this label. Consult the manufacturer, retailer or
agent with regard to obtaining a manufacturing specification and
shape for replacement glass quoting the model number and batch
number or date of manufacture.
Imported by:
Justwise Group Ltd
6 The Shires
Shire Hill Industrial Estate
Saffron Walden
Essex
CB11 3AP
P/O No: K10776/10

Please check you have all the parts listed below
Components - Parts
4Top panel x 1
(36.5x36.5cm)
5Panel x 2
(33.8x31.4cm)
6Stretcher x 4
(28x2.2cm)
7Adjustable shelf x 2
(31.9 x31.4cm)
8Fixed shelf x 1
(29x30.5cm)
1 Front panel x 1
(169.3x33.4cm)
2 Back panel x 1
(169.3x33.4cm)
3 Side panel x 2
(152x28.7cm)
2
Inside
FRONT
FRONT
If you have damaged or missing components,
call the Customer Helpline: 08456 400800

Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
3
Eye protection
(when using a drill
or hammer)
Drill
A
40mm Wood dowel x 16
30mm Wood dowel x 4
B
30mm screw x 12
C
D E F
I
16mm knob screw x 2
G
Door knob x 2
H
Shelf support pin x 8 Adjustable feet x 4
Wall strap x 2
12mm Screw x 2
Suitable drill bit
(for use with wall plug
(only for use when wall fixing)
of your choice)
Please check you have all the parts listed below
Phillips screwdriver
(medium & large) Ruler/tape
measur
Rule - Use this ruler to help correctly identify the screws
Tools required

Preparing stretchers
Fit wood dowels into
the holes in both ends of
stretchers .
Step 1
Attaching stretchers
Lay back panel flat onto
the floor with the fixing
holes facing up.
Locate stretchers onto
back panel by aligning
the wood dowels as shown.
Locate sheft onto back
panel by aligning the
wood dowels as shown.
Note: The grooves in
stretchers must face
in to the middle of the
back panel as shown.
Step 2
4
A
6
Fit wood dowels into
the holes in both ends of
shelf .
D
8
2
6
2
6
6
Top
Groove
to face
down
Groove
to face
down
6
2
2
8
6
6
Groove
to face
up
Groove
to face
up
Bottom
2
8
2
8
6
6
6
6
A
A
A
D
D
A
Assembly Instructions

5
Attaching top and
bottom panels
Assemble top panel to
back panel using
screws .
Note: The front of the top
panel has been
labelled for easier
identification.
Assembly Instructions
Step 3
Fitting side panels
Carefully slide side panels
into the grooves in
stretchers .
Ensure the side
panels also fit down into
the grooved edge of back
panel .
Step 4
Top
Bottom
4
4
B
B
5
5
2
4
2
B
Assemble both panels
to back panel
using screws .
5 2
B
3
3
3
66
6
6
2
6
2
B
5
5
8
8
FRONT
Note:
4

6
Assembly Instructions
Step 5
3
8
3
1
Attaching door knobs
Attach door knobs
to the upper and lower
doors using screws .
G
F
Attaching front panel
With help, carefully lower
front panel down into
position.
Note: Ensure the wood
dowels are aligned and
ensure side panels fit
inside the grooves in
front panel .
Secure front panel
using screws , through
top panel and panels .
Screw height adjustable
feet into the bottom of
front and back panels
and .
Step 6
1
1
3
1
B
G
F
F
G
1
I
4
B
5
B
5
B
B
I
I
I
I
Adjustable feet
2
4
I
1
2
5

8
Assembly Instructions
Step 7
7
H
7
H
Fitting shelves
Fit shelf support pins
at the desired height in
upper and lower cabinets.
Locate shelves onto
the support pins.
Note: The front edges of
shelves have been
labelled for easier
identification.
H
7
FR
ON
T
7
Labelled
underneath
FR
ON
T
Labelled
underneath

Assembly Instructions
Step 8
Assembly is complete.
If you need help for have damaged or missing parts, call the Customer helpline:08456 400800
Justwise Group Ltd., 6 The Shires, Shirehill Industrial Estate, Saffron Walden, Essex. CB11 3AP
Fixing to the wall
It is recommended that the
unit is fixed to the wall to
ensure stability.
Assemble wall straps
to the back of the unit
using screws .
With help, move the
unit to the desired
location.
Mark the fixing hole
locations on the wall and
remove the unit.
Drill the wall and fit suitable
plugs for your wall type.
Note: Wall plugs are not
supplied.
Re-position the unit and
secure the wall straps to
the wall.
Note: Screws are not
supplied.
pipes or cables.
Warning: Before
drilling. Check the
wall for hidden
C
E
C
C
E
E