JVC KA-790G User manual

Please read the following before getting started:
Thank you for purchasing this JVC product.
Before operating this unit, please read the instructions
carefully to ensure the best possible performance.
Transportation
Do not drop or hit this unit against a hard object when
transporting.
Maintenance
䡵 Wipe the external cabinet of the unit with a soft cloth. Do not
wipe the body with benzene or thinner. Doing so may cause the
surface to melt or turn cloudy. When it is extremely dirty, soak the
cloth in a solution of neutral detergent, wipe the body with it, and
then use a clean cloth to remove the detergent.
STUDIO ADAPTER
KA-790G INSTRUCTIONS
LST1095-001A
Information for Userson Disposal of Old Equipment
[European Union]
Thissymbol indicatesthat the electricaland electronic
equipment should not bedisposed as generalhousehold
waste atitsend-of-life. Instead, the product should behanded
over to the applicable collection point for the recycling of
electricaland electronic equipment for proper treatment,
recovery and recycling in accordance with yournational
legislation.
By disposing of thisproduct correctly, youwill help to conserve
naturalresourcesand will help prevent potentialnegative
effectson the environment and humanhealth which could
otherwisebecaused byinappropriate waste handling of this
product. For more information about collection point and
recycling of thisproduct, please contact your localmunicipal
office, yourhousehold waste disposalservice or the shop
where youpurchased the product.
Penaltiesmaybeapplicable
for incorrect disposalofthiswaste, in accordance with national
legislation.
(Business users)
If youwish to dispose of thisproduct, please visit our web
page http://www.jvc.euto obtain information about the take-
back of the product.
[Other Countriesoutside the European Union]
If youwish to dispose of thisproduct, pleasedosoin
accordance with applicable national legislation or other rules
in your country for the treatment of old electricaland
electronic equipment.
Attention:
Thissymbol isonly valid in the European Union.
Dear Customer,
This apparatus is in conformance with the valid European directives and
standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
Sehr geehrter Kunde, sehr geehrte Kundin,
dieses Gerät stimmt mit den gültigen europäischen Richtlinien und
Normen bezüglich elektromagnetischer Verträglichkeit und
elektrischer Sicherheit überein.
Die europäische Vertretung für die Victor Company of Japan,
Limited ist:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Deutschland

General
Supplied Accessories
Dimensional Outline Drawing (Unit: mm)
* The specifications and appearance of this product are subject to changes for further improvement without prior notice.
Specifications
Mass :Approx. 5.4 kg
Allowable operating
temperature
:0 Ito 40 I(32 Jto 104 J)
Allowable operating humidity :30 % RH to 80 % RH
Allowable storage
temperature
:-20 Ito 60 I(-4 Jto 122 J)
Instructions 1
Warranty Card (For USA and Canada) 1
400 262
280 5.4
285.4
107.45 48 22 96
(=3xP16) (=6xP16)

Memo :
●Other than when attaching or detaching the camera, be
sure to tighten the two screws on the sides. It could be
dangerous especially during transportation when it is more
unstable. Make sure that the screws are fixed in place
before transporting.
●Be careful not to get your fingers caught when opening and
closing this unit.
●When transporting this unit by itself or when a camera is
loaded, be sure to hold the bars on both sides of this unit.
Do not hold the handle on the camera when transporting.
This unit may fall off from the camera and cause injuries.
1 Mount this unit on your tripod using a suitable
mounting hole.
2 Loosen the two screws on the sides and open this
unit.
Note :
●For your safety, use a tripod that is able to withstand a load
of 20 kgand above.
3 Check that the front mount clip is not sticking out.
If the clip is sticking out, pull the lock lever while pressing the
safety lever to release the lock.
4 Align the mounting bracket with the pin position and
slide the camera in.
Attach firmly until it clicks into place.
Installation
2
1
To Tr i p o d
Open
Safety Lever
Lock Lever
Locked Released
Front Mount Clip
Click
Rear Mounting Bracket
Front Mounting Bracket
Pin

5 Connect the cables and close this unit.
6 Tighten the two screws on the sides firmly.
7 Bundle the cables.
If necessary, remove the cap and bundle the cables with a
cable clamp.
8 Attach the VF-HP790G, accessories, etc.
Memo :
●For details, refer to the [INSTRUCTIONS] of VF-HP790G.
5
6
Close
7Cap
Cable Clamp
2010 Victor Company of Japan, Limited LST1095-001A