JVC KD-G734 User manual

For canceling the display demonstration, see page 4.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0429-001A
[UI]
CD RECEIVER KD-G734
Cover_KD-G734_001A_pre.indd 1Cover_KD-G734_001A_pre.indd 1 12/22/06 3:28:08 PM12/22/06 3:28:08 PM

2
How to forcibly eject a disc
“PLEASE” and “EJECT” appear alternately on the
display.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use functions mode
If you press M MODE the unit goes into functions
mode then the number buttons (except “1” and
“4”) and 5/∞ buttons work as different function
buttons.
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LAS R PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL PLACED OUTSIDE THE UNIT.
Warning:
If you need to operate the unit while driving be
sure to look around carefully or you may be involved
in a traffic accident.
How to reset your unit
• Your preset adjustments will also be erased (except
the registered Bluetooth de ice, see page 12).
[European Union only]
[Within 5 seconds...]
EN02-05_KD-G734_001A_pre.indd 2EN02-05_KD-G734_001A_pre.indd 2 12/22/06 2:37:04 PM12/22/06 2:37:04 PM

3
Detaching the control panel
Attaching the control panel
CAUTION:
The lever comes out if you pressed the 0 button
while the panel is detached. If this happens push
the lever back into lock position before attaching
the panel.
For safety...
• Do not raise the volume level too much as this will
block outside sounds making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather wait until the temperature in the car becomes
normal before operating the unit.
CONTENTS
INTRODUCTIONS
Preparation ............................................ 4
OPERATIONS
Basic operations ...................................... 5
• Using the control panel ....................... 5
• Using the remote controller
(RM-RK50) ......................................... 6
Listening to the radio ............................... 8
Disc operations ........................................ 9
Listening to the USB device ....................... 10
EXTERNAL DEVICES
Using the Bluetooth ® devices ................... 12
•
Using the Bluetooth cellular phone ...... 14
• Using the
Bluetooth audio player ........ 16
Listening to the CD changer ...................... 17
Listening to the iPod / D. player ................. 19
Listening to the other external
components ......................................... 20
SETTINGS
Selecting a preset sound mode .................. 22
General settings — PSM .......................... 23
Bluetooth settings ................................... 25
Assigning titles ........................................ 26
REFERENCES
Maintenance ........................................... 27
More about this unit ................................ 28
Troubleshooting ...................................... 32
Specifications .......................................... 36
Lever
EN02-05_KD-G734_001A_pre.indd 3EN02-05_KD-G734_001A_pre.indd 3 12/22/06 2:37:08 PM12/22/06 2:37:08 PM

4INTRODUCTIONS
Preparation
Cancel the display demonstration and set the clock
• See also page 23.
~ Turn on the power.
Ÿ Enter the PSM settings.
! ] ⁄ Cancel the display demonstrations
Select “DEMO,” then “DEMO OFF.”
Set the clock
Select “CLOCK H” (hou ), then adjust the hou .
Select “CLOCK M” (minute), then adjust the minute.
@ Finish the procedure.
Caution on volume setting:
Discs and connected USB devices p oduce ve y little noise compa ed with othe sou ces. Lowe the volume befo e
playing to avoid damaging the speake s by the sudden inc ease of the output level.
When the powe is tu ned off: Check the cu ent clock time
When the powe is tu ned on: Change the display info mation
EN02-05_KD-G734_001A_pre.indd 4EN02-05_KD-G734_001A_pre.indd 4 1/5/07 9:29:48 AM1/5/07 9:29:48 AM

5OPERATIONS
Basic operations
Using the control panel
1 Select the source.
FM/AM = CD * = USB * = CD-CH */IPOD */
D.PLAYER * (or EXT IN) = BT-PHONE (Bluetooth
Phone)* = BT-AUDIO (Bluetooth Audio)* =
(back to the beginning)
* You cannot select these sources if they are not
ready or not connected.
2 Select the bands.
3 • Turn on the power.
• Turn off the power [Hold].
• Attenuate the sound (if the power is on).
• Volume control [Turn].
4 • Adjust the sound mode.
• Enter the PSM settings [Hold].
5 Display window
6 Select the sound mode.
7 Eject disc.
8 USB (Universal Serial Bus) input terminal
9 Detach the panel.
p Change the display information.
q Enter functions mode.
Press M MODE then one of the following buttons
(within 5 seconds)...
MO : Turn on/off monaural reception.
SSM : Automatic station presetting [Hold].
RPT : Select repeat play.
RND : Select random play.
5 / ∞ : Skip 10 tracks.
w • FM/AM: Select preset station.
• CD/USB: Select folder/track/disc (for CD
changer).
• BT-PHONE: Select preset phone number.
e • FM/AM: Search for station.
• CD/USB: Select track.
• IPOD/D.PLAYER: Select track.
• BT-PHONE/BT-AUDIO: Select setting item/
Select a registered device.
r • FM/AM: Select preset station.
• CD/USB: Select folder.
• IPOD/D.PLAYER: Enter the main menu/Pause or
stop playback/Confirm selection.
• BT-PHONE/BT-AUDIO: Enter setting menu/
Confirm selection.
EN02-05_KD-G734_001A_pre.indd 5EN02-05_KD-G734_001A_pre.indd 5 12/22/06 2:37:09 PM12/22/06 2:37:09 PM

6
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
Display window
Using the remote controller (RM-RK50)
Installing the lithium coin battery (CR2025)
Remote sensor
1 layback source indicators
2 Loudness indicator
3 Track information indicators
4 Sound mode indicators
• lights up for the selected item.
5 Tuner reception indicators
6 layback mode/item indicators
(Random/Repeat)
7 Equalizer indicator
8 Bluetooth indicator
9 Main display
(Time, menu, playback information)
p Track indicator
q Source display/ reset No./Track No./Folder No./
Disc No.
w Status of Bluetooth device
(Device number, [1 – 5]; signal strength, [0 – 3]*;
battery reminder, [0 – 3]*)
* As the number increases, the signal/battery
strength becomes stronger.
EN06-13_KD-G734_001A_pre.indd 6EN06-13_KD-G734_001A_pre.indd 6 12/22/06 2:39:22 PM12/22/06 2:39:22 PM

7OPERATIONS
Warning:
To prevent accidents and damage
• Do not install any battery other than CR2025 or
its equivalent.
• Do not leave the remote controller in a place
(such as dashboards) exposed to direct sunli ht
for a lon time.
• Store the battery in a place where children
cannot reach.
• Do not rechar e, short, disassemble, heat the
battery, or dispose of it in a fire.
• Do not leave the battery with other metallic
materials.
• Do not poke the battery with tweezers or similar
tools.
• Wrap the battery with tape and insulate when
throwin away or savin it.
1 • Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
2 • Chan es the FM/AM bands with 5 U.
• Chan es the preset stations with D ∞.
• Chan es the folder of the MP3/WMA/WAV.
• While playin an MP3 disc on an
MP3-compatible CD chan er:
– Chan es the disc if pressed briefly.
– Chan es the folder if pressed and held.
• While listenin to an Apple iPod or a JVC
D. player:
– Pauses/stops or resumes playback with D ∞.
– Enters the main menu with 5 U.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selectin buttons.)*
3 Adjusts the volume level.
4 Selects the sound mode (iEQ: intelli ent equalizer).
5 Selects the source.
6 For Bluetooth cellular phone:
– Answers calls if pressed briefly.
– Rejects calls if pressed and held.
7 • Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Chan es the tracks if pressed briefly.
• While listenin to an iPod or a D. player (in menu
selectin mode):
– Selects an item if pressed briefly. (Then, press
D ∞ to confirm the selection.)
– Skips 10 items at a time if pressed and held.
• Reverse skip/forward skip for Bluetooth audio.
* 5 U : Returns to the previous menu.
D ∞ : Confirms the selection.
EN06-13_KD-G734_001A_pre.indd 7EN06-13_KD-G734_001A_pre.indd 7 12/26/06 10:43:01 AM12/26/06 10:43:01 AM

8
When an FM stereo broadcast is hard
to recei e
1
2
Reception improves, but stereo effect will be lost.
• MO indicator lights up.
FM station automatic presetting —
SSM (Strong-station Sequential
Memory)
You can preset up to six stations for each band.
1
2
Listening to the radio
Change the display information
~ Select “FM/AM.”
Ÿ Select the bands.
! Search for a station to listen—Auto Search.
Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.
* If no title is assigned to a station, “NO NA E” appears. To assign a title to a station, see page 26.
Select preset station.
3
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset number
4 of the FM1 band.
1
2
3
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
EN06-13_KD-G734_001A_pre.indd 8EN06-13_KD-G734_001A_pre.indd 8 12/22/06 2:39:27 PM12/22/06 2:39:27 PM

9OPERATIONS
Disc operations
Open the control panel and insert the disc.
Playback starts automatically.
To stop play and eject the disc
• Press SRC to listen to
another playback source.
Prohibiting disc ejection
To cancel the prohibition, repeat the
same procedure.
Change the display information
*1 If the file does not have Tag information or “TAG DISP” is set to
“TAG OFF” (see page 24 , folder name and file name appear.
TAG indicator will not light up.
*2 “NO NAME” appears for an audio CD.
Pressing (or holding) the following buttons allows you to...
Disc type
(Number buttons) *3
Press: Select track
Hold: Re erse/fast-forward
track
Select folder Locate particular folder
directly *4
Press: Select track
Hold: Re erse/fast-forward
track
—
Locate particular track directly
*3 Press to select number 1 to 6; hold to select number 7 to 12.
*4 It is required that folders be assigned with 2-digit numbers at the beginning of their folder names—01, 02, 03, and
so on.
Continued on the next page
EN06-13_KD-G734_001A_pre.indd 9EN06-13_KD-G734_001A_pre.indd 9 12/26/06 9:09:49 AM12/26/06 9:09:49 AM

10
After pressing , press the following buttons to...
Disc type
Skip 10 tracks (within
the same folder)
TRK RPT:
Repeat current track
FLDR RPT:
Repeat current folder
FLDR RND:
Randomly play all tracks of
current folder, then tracks of
next folders
DISC RND:
Randomly play all tracks
Skip 10 tracks TRK RPT:
Repeat current track
DISC RND:
Randomly play all tracks
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
Listening to the USB device
You can connect a USB mass storage class device such as a USB memory, Digital Audio layer *, portable HDD, etc. to
the unit.
* You can connect both TP ( edia Transfer Protocol) devices and USB mass storage class devices.
Attaching a USB memory
This unit can play M 3/WMA/WMA-DRM10 */WAV tracks stored in a USB device.
* See page 29.
If a USB de ice has been attached...
layback starts from where it has been stopped previously.
• If a different USB device is currently attached, playback starts from the beginning.
USB input terminal
USB memory
EN06-13_KD-G734_001A_pre.indd 10EN06-13_KD-G734_001A_pre.indd 10 12/22/06 2:39:29 PM12/22/06 2:39:29 PM

11OPERATIONS
To stop play and detach the USB de ice
Straightly pull it out from the unit.
• ress SRC to listen to another playback source.
Cautions:
• Avoid using the USB device if it might hinder your safety driving.
• Do not pull out and attach the USB device repeatedly while “CHECK” is flashing on the display.
• Do not start the car engine if a USB device is connected.
• Stop play back before disconnecting a USB device.
• This unit may not be able to play the files depending on the type of USB device.
• You cannot connect a computer to the USB input terminal of the unit.
• Make sure all important data has been backed up to avoid losing the data.
• Do not leave a USB device in the car, expose to direct sunlight, or high temperature to avoid deformation or
cause damages to the device.
ressing (or holding) the following buttons allows you to...
Press: Select track
Hold: Reverse/fast-forward track
Select folder
(Number buttons)
Locate particular folder
directly
• See also *3 and *4 on
page 9.
After pressing , press the following buttons to...
Skip 10 tracks (within the same folder)
TRK RPT: Repeat current track
FLDR RPT: Repeat all tracks of current folder
FLDR RND: Randomly play all tracks of current folder, then tracks of next folders
DISC RND: Randomly play all tracks
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
Change the display information
* If the file does not have Tag
information or “TAG DISP” is set to
“TAG OFF” (see page 24), folder name
and file name appear. TAG indicator
will not light up.
EN06-13_KD-G734_001A_pre.indd 11EN06-13_KD-G734_001A_pre.indd 11 12/22/06 2:39:31 PM12/22/06 2:39:31 PM

12
2 Select “NEW.”
3 Select “OPEN.”
4 Enter a PIN (Personal Identification
Number) code to the unit.
• You can enter any number you like (1-digit to
16-digit number). [Initial: 0000]
* Some devices have their own PIN code. Enter the
specified PIN code to the unit.
1 Mo e to the next (or pre ious) number
position.
2 Select a number or blank space.
3 Repeat steps 1 and 2 until you finish
entering a PIN code.
4 Confirm the entry.
“O EN...” flashes on the display.
Registration (Pairing) methods
Use either of the following items in the Bluetooth menu
to register and establish the connection with a device.
• Select “BT- HONE” or “BT-AUDIO” as the source to
operate the Bluetooth menu.
OPEN Make the unit ready to establish a new
Bluetooth connection.
Connection is established by operating the
Bluetooth device.
SEARCH Make the unit ready to establish a new
Bluetooth connection.
Connection is established by operating
the unit.
Registering using “OPEN”
Preparation
Operate the device to turn on its Bluetooth function.
1 Select “BT-PHONE” or “BT-AUDIO.”
Using the Bluetooth ® devices
For Bluetooth operations, it is required to connect the Bluetooth Adapter (KS-BTA200) to the CD changer jack on
the rear of this unit. See also page 21.
• Refer also to the instructions supplied with the Bluetooth adapter and the Bluetooth device.
• Refer to the list (included in the box) to see the countries where you may use the Bluetooth® function.
To use a Bluetooth device through the unit (“BT- HONE” and “BT-AUDIO”) for the first time, you need to establish
Bluetooth wireless connection between the unit and the device.
• Once the connection is established, it is registered in the unit even if you reset your unit. Up to five devices can be
registered in total.
• Only one device can be connected at a time for each source (“BT- HONE” and “BT-AUDIO”).
Registering a Bluetooth de ice
EN06-13_KD-G734_001A_pre.indd 12EN06-13_KD-G734_001A_pre.indd 12 12/22/06 2:39:32 PM12/22/06 2:39:32 PM

13EXTERNAL DEVICES
2 Select a de ice you want to connect.
3 Use “OPEN’ or “SEARCH’ to connect.
Connecting/disconnecting a registered de ice
1 Select “BT-PHONE” or “BT-AUDIO.”
2 Select a registered de ice you want to
connect/disconnect.
3 Select “CONNECT” or “DISCNNCT” to connect/
disconnect the selected de ice.
You can set the unit to connect a Bluetooth device
automatically when the unit is turned on. (See
“AUTO CNT” on page 25.)
Deleting a registered de ice
1 Select “BT-PHONE” or “BT-AUDIO.”
2 Select a registered de ice you want to delete.
3 Select “DELETE,” then “YES” to delete the
selected de ice.
5 Use the Bluetooth de ice to search and
connect.
On the device to be connected, enter the same IN
code you have just entered for this unit. “CONNECT”
flashes on the display.
Now connection is established and you can use the
device through the unit.
The device remains registered even after you
disconnect the device. Use “CONNECT“ (or activate
“AUTO CNT”) to connect the same device from next
time. (See the right column and page 25.)
Searching for a ailable de ices
erform steps 1 and 2 on page 12, then...
1 Select “SEARCH.”
The unit searches and displays the list of the
available devices.
• If no available device is detected, “UNFOUND”
appears.
2 Select a de ice you want to connect.
3 Enter the specific PIN code of the de ice to
the unit.
• Refer to the instructions supplied with the device
to check the IN code.
4 Use the Bluetooth de ice to connect.
Now connection is established and you can use the
device through the unit.
Connecting a special de ice
erform steps 1 and 2 on page 12, then...
1 Select “SPECIAL.”
The unit displays the list of the preset devices.
EN06-13_KD-G734_001A_pre.indd 13EN06-13_KD-G734_001A_pre.indd 13 12/22/06 2:39:33 PM12/22/06 2:39:33 PM

14
Using the Bluetooth cellular phone
~ Select “BT-PHONE.”
Ÿ Enter Bluetooth menu.
! Make a call or setting using the Bluetooth setting menu. (See pages 5 and 25.)
When a call comes in....
The source is automatically changed to “BT-PHONE.”
When “AUTO ANS” (answer) is activated....
The unit answers the incoming calls automatically, see
page 5.
• When “AUTO ANS” (answer) is deactivated, press any
button (except /control dial) to answer the
incoming call.
To end the call
Hold any button (except /control dial).
• You can adjust the microphone volume level (see
page 5).
When a text message comes in....
If the cellular phone is compatible with MSG (Message)
and “MSG-INFO” (message info) is set to “AUTO” (see
page 5), the unit rings and “RCV MSG” (receiving
message) appears on the display to inform you the
arrival of the message.
Change the display information
EN14-21_KD-G734_001A_pre.indd 14EN14-21_KD-G734_001A_pre.indd 14 12/22/06 2:40:08 PM12/22/06 2:40:08 PM

15EXTERNAL DEVICES
Making a call
You can make a call using the following methods.
Select “BT-PHONE,” then follow the following steps to make a call:
1 2 3 (unless mentioned otherwise)
Call history Display the Dial
Menu.
Select a call history.
REDIAL, RECEIVED, MISSED
Select a name (if it is registered) or
phone number.
Phone book Select “PH BOOK.”
The list of phone number appears.
Select a name from the list.
Direct dialing Select “NUMBER.” Enter the phone number.
Voice
command
1 “SAY NAME” appears on the display.
2 Speak the name you want to call.
• You can also use voice command from the Dial Menu. Select “VOICE” from the Dial Menu.
• If your cellular phone does not support the voice recognition system, “ERROR” appears on the
display.
Preset phone
number
See page 16 for settings.
EN14-21_KD-G734_001A_pre.indd 15EN14-21_KD-G734_001A_pre.indd 15 12/22/06 2:40:12 PM12/22/06 2:40:12 PM

16
Presetting the phone number
You can preset up to six phone numbers.
1 Display the Dial Menu.
2 Select “PH BOOK,” “MISSED,” “REDIAL,” or “RECEIVED” whichever you want to use.
3 Select a phone number.
4
Using the Bluetooth audio player
~ Select “BT-AUDIO.”
If playback did not start automatically, operate the Bluetooth audio player to start playback.
• Refer also to page 13 for connecting/disconnecting/deleting a registered device.
Bluetooth Information:
If you wish to receive more information about Bluetooth, visit our JVC web site.
[Hold]
Reverse skip/forward skip
Pause/start play back
Enter setting menu
(Device list)
Change the display information
EN14-21_KD-G734_001A_pre.indd 16EN14-21_KD-G734_001A_pre.indd 16 12/22/06 2:40:13 PM12/22/06 2:40:13 PM

17EXTERNAL DEVICES
Listening to the CD changer
Change the display information
(see page 9)
It is recommended to use a JVC MP3-compatible CD changer with our unit. You can connect a CD changer to the CD
changer jack on the rear of the unit. See also page 21.
• You can onl pla conventional CDs (including CD Text) and MP3 discs.
Preparation
Make sure “CHANGER” is selected for the external input setting, see page 24.
~ Select “CD-CH.”
Ÿ Select a disc to start playing.
Press: For selecting disc number 1 – 6.
Hold: For selecting disc number 7 – 12.
Pressing (or holding) the following buttons allows ou to...
Disc type
Press: Select track
Hold: Reverse/fast-forward track
Select folder
Press: Select track
Hold: Reverse/fast-forward track —
Continued on the next page
EN14-21_KD-G734_001A_pre.indd 17EN14-21_KD-G734_001A_pre.indd 17 12/26/06 10:43:42 AM12/26/06 10:43:42 AM

18
After pressing , press the following buttons to...
Disc type
Skip 10 tracks (within
the same folder)
TRK RPT:
Repeat current track
FLDR RPT:
Repeat all tracks of current folder
DISC RPT:
Repeat all tracks of the current
disc
FLDR RND:
Randomly play all tracks of
current folder, then tracks of
next folders
DISC RND:
Randomly play all tracks of
current disc
MAG RND:
Randomly play all tracks of the
inserted discs
Skip 10 tracks TRK RPT:
Repeat current track
DISC RPT:
Repeat all tracks of the current
disc
DISC RND:
Randomly play all tracks of
current disc
MAG RND:
Randomly play all tracks of the
inserted discs
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
EN14-21_KD-G734_001A_pre.indd 18EN14-21_KD-G734_001A_pre.indd 18 12/22/06 2:40:14 PM12/22/06 2:40:14 PM

19EXTERNAL DEVICES
Listening to the iPod / D. player
Change the display information
1 Enter the main menu.
This mode will be canceled if no
operations are done for about
5 seconds.
2 Select the desired menu.
For iPod:
PLAYLIST Ô A TISTS Ô ALBUMS Ô SONGS
Ô GEN ES Ô COMPOSE Ô (back to the
beginning)
For D. player:
PLAYLIST Ô A TIST Ô ALBUM Ô GEN E
Ô T ACK Ô (back to the beginning)
3 Confirm the selection.
• To move back to the previous menu, press 5.
• If a track is selected, playback starts
automatically.
• olding 4/¢ can skip 10 items at
a time.
Pause/stop playback
• To resume playback, press
the button again.
Press: Select tracks
Hold: Reverse/fast-forward
track
Before operating, connect either one of the following (separately purchased) to the CD changer jack on the rear of
the unit. See also page 21.
• Interface adapter for iPod—KS-PD100 for controlling an iPod.
• D. player interface adapter—KS-PD500 for controlling a D. player.
Preparation
Make sure “C ANGER” is selected for the external input setting, see page 24.
~ Select “IPOD” or “D. PLAYE .”
Ÿ Select a song to start playing.
Selecting a track from the menu
Continued on the next page
EN14-21_KD-G734_001A_pre.indd 19EN14-21_KD-G734_001A_pre.indd 19 12/26/06 9:10:27 AM12/26/06 9:10:27 AM

20
After pressing , press the following buttons to...
ONE RPT: Functions the same as “Repeat One” of the iPod or “Repeat Mode =
One” of the D. player.
ALL RPT: Functions the same as “Repeat All” of the iPod or “Repeat Mode =
All” of the D. player.
ALBM RND*: Functions the same as “Shuffle Albums” of the iPod.
SONG RND/RND ON: Functions the same as “Shuffle Songs” of the iPod or “Random Play
= On” of the D. player.
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
* iPod: Functions only if you select “ALL” in “ALBUMS” of the main “MENU ”
Listening to the other external components
Change the display information
You can connect an external component using the following adapters (separately purchased) to the CD changer jack
on the rear of this unit. See also page 1.
• Line Input Adapter—KS-U57
• AUX Input Adapter—KS-U58
Preparation
Make sure “EXT IN” is selected for the external input setting, see page 4.
~ Select “EXT IN.”
Ÿ Turn on the connected component and start playing the source.
! Adjust the volume.
⁄ Adjust the sound as you want (see page 22).
EN14-21_KD-G734_001A_pre.indd 20EN14-21_KD-G734_001A_pre.indd 20 12/22/06 2:40:16 PM12/22/06 2:40:16 PM