JVC KD-R862BT User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
B5A-0112-00 [U]
KD-R862BT
CD RECEIVER
INSTRUCTION MANUAL Please read all instructions carefully before
operation to obtain the best possible performance
from the unit.
JS_JVC_KD_R862BT_U_C00.indd 1JS_JVC_KD_R862BT_U_C00.indd 1 17/7/2014 11:42:22 AM17/7/2014 11:42:22 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
CONTENTS BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short
circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to
evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate. (
3 )
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
CD / USB / iPod / ANDROID 5
RADIO 7
AUX 8
Pandora® (Applicable for Australia or
New Zealand models only) 9
iHeartRadio® (Applicable for Australia
or New Zealand models only) 10
BLUETOOTH® 11
AUDIO SETTINGS 17
DISPLAY SETTINGS 19
MORE INFORMATION 19
TROUBLESHOOTING 21
INSTALLATION /
CONNECTION 24
SPECIFICATIONS 26
How to read this manual
• Operations are explained mainly
using buttons on the faceplate.
• [
XX ] indicates the selected items.
• (
XX ) indicates references are
available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse
side of the faceplate)
JS_JVC_KD_R862BT_U_EN_1.indd 2JS_JVC_KD_R862BT_U_EN_1.indd 2 17/7/2014 12:00:08 PM17/7/2014 12:00:08 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power. —
Adjust the volume Turn the volume knob. Press or .
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press repeatedly.
• Press , then turn the volume knob within 2 seconds.
Press SOURCE repeatedly.
Change the display
information
Press repeatedly. (
21 )—
Attach
How to reset
Detach
Your preset adjustments
will also be erased.
Remote control (RM-RK52)Faceplate
Volume knob
(turn/press) Loading slot
Detach
button
Display window
How to replace the battery
Pull out the insulation sheet
when using for the first time.
Remote sensor (Do not expose
to bright sunlight.)
JS_JVC_KD_R862BT_U_EN_1.indd 3JS_JVC_KD_R862BT_U_EN_1.indd 3 17/7/2014 12:00:11 PM17/7/2014 12:00:11 PM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
1 Press and hold .
2 Turn the volume knob to select [ DEMO ], then press the knob.
3 Turn the volume knob to select [ DEMOOFF ], then press the knob.
4 Press to exit.
Set the clock
1 Press and hold .
2 Turn the volume knob to select [ CLOCK ], then press the knob.
3 Turn the volume knob to select [ CLOCKSET ], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [ 24H/ 12H ], then press the knob.
6 Turn the volume knob to select [ 12 HOUR ] or [ 24 HOUR ], then press the
knob.
7 Press to exit.
To return to the previous setting item, press .
Set the basic settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
1
2
Default: XX
SETTINGS
BEEP ON
:Activates the keypress tone.; OFF :Deactivates.
SRC SELECT
AM
* ON :Enables AM in source selection.; OFF :Disables.
SW1 * ON :Enables SW1 in source selection.; OFF :Disables.
SW2 * ON :Enables SW2 in source selection.; OFF :Disables.
PANDORA * ON :Enables PANDORA in source selection.; OFF :Disables.
IHEART * ON :Enables IHEARTRADIO in source selection.; OFF :Disables.
AUX * ON :Enables AUX in source selection.; OFF :Disables.
F/W UPDATE
SYSTEM / BLUETOOTH
F/W xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
CLOCK
CLOCK SYNC AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Data System signal.;
OFF :Cancels.
CLOCK DISP ON :The clock time is shown on the display even when the unit is turned
off.;
OFF :Cancels.
* Not displayed when the corresponding source is selected.
3
JS_JVC_KD_R862BT_U_EN_1.indd 4JS_JVC_KD_R862BT_U_EN_1.indd 4 17/7/2014 12:00:12 PM17/7/2014 12:00:12 PM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD / USB / iPod / ANDROID
To On the faceplate On the remote control
Reverse / Fast-forward*3Press and hold . Press and hold .
Select a track/file Press .Press .
Select a folder*4Press . Press .
Repeat play*5Press repeatedly.
TRACK RPT / RPT OFF : Audio CD or JVC Playlist Creator (JPC) /
JVC Music Control (JMC) file (
20 )
TRACK RPT / FOLDER RPT / RPT OFF : MP3/WMA/AAC/WAV file
ONE RPT / ALL RPT / RPT OFF : iPod or ANDROID
Random play*5Press repeatedly.
ALL RND / RND OFF : Audio CD
FOLDERRND / ALL RND / RND OFF : MP3/WMA/AAC/WAV file or JPC / JMC
file
SONG RND / ALL RND / RND OFF : iPod or ANDROID
*1
Do not leave the cable inside the car when not using.
*2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
(
20 )
*3
For ANDROID: Applicable only when [ AUTO MODE ] is selected. ( 6 )
*4
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.
*5
For iPod/ ANDROID: Applicable only when [ HEAD MODE ]/ [ AUTO MODE ] is selected. ( 6 )
Start playback
The source changes automatically and
playback starts.
CD
Eject disc Label side
USB input terminal
USB 2.0 cable
*1
(commercially available)
Micro USB 2.0 cable
*1
(commercially available)
(Accessory of the iPod/
iPhone)*
1
USB
iPod/iPhone
ANDROID*2
JS_JVC_KD_R862BT_U_EN_1.indd 5JS_JVC_KD_R862BT_U_EN_1.indd 5 17/7/2014 12:00:13 PM17/7/2014 12:00:13 PM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
To On the faceplate
Select control
mode
While in iPod source, press repeatedly.
HEAD MODE : Control from the unit.
IPHONE MODE : Control from the iPod/iPhone. However, you
can still play/pause or file skip from the unit.
While in ANDROID source, press
repeatedly.
AUTO MODE : Control from the unit (using JVC MUSIC
PLAY application).
AUDIO MODE : Control other media player applications
from the Android device (without using JVC
MUSIC PLAY application). However, you can
still play/pause or file skip from the unit.
Select music
drive
Press repeatedly.
The stored songs in the following start playback.
• Selected internal or external memory of a smartphone
(Mass Storage Class).
• Selected drive of a multiple drives device.
Change the playback speed of the Audiobook
While listening to the iPod and [ HEADMODE ] is selected ( Select control mode )....
1 Press and hold .
2 Turn the volume knob to select [ IPOD ], then press the knob.
3 Press the volume knob to select [ AUDIOBOOKS ].
4 Turn the volume knob to make a selection, then press the knob.
0.5×SPEED / 1×SPEED / 2×SPEED : Select the desired playback speed of the
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
5 Press to exit.
To return to the previous setting item, press .
Select a file from a folder/list
1 Press .
2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA/AAC/WAV or JPC / JMC file:
Turn the volume knob quickly.
For iPod:
You can search for a file according to the first character.
Press or turn the volume knob quickly to select the
desired character (A to Z/ 0to9/ OTHERS).
• Select “OTHERS” if the first character is other than Ato Z,
0 to 9.
• To return to the previous setting item, press .
• To cancel, press and hold .
• For iPod, applicable only when [
HEADMODE ] is selected. (  Select
control mode
)
• For ANDROID, applicable only when [
AUTO MODE ] is selected.
(
Select control mode )
CD / USB / iPod / ANDROID
JS_JVC_KD_R862BT_U_EN_1.indd 6JS_JVC_KD_R862BT_U_EN_1.indd 6 17/7/2014 12:00:14 PM17/7/2014 12:00:14 PM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
1 Press repeatedly to select FM, AM, SW1 or SW2.
2 Press (or press on RM-RK52) to search for a station automatically.
(or)
Press and hold (or press and hold on RM-RK52) until “M” flashes,
then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM/SW1/SW2.
Store a station
While listening to a station....
Press and hold one of the number buttons (1to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press
2 Turn the volume knob to select a preset number, then press the knob to
confirm.
Other settings
1 Press and hold .
2 Turn the volume knob to select [ TUNER ], then press the
knob.
3 Turn the volume knob to make a selection ( see the
following table
) , then press the knob.
4 Repeat step 3until the desired item is selected/
activated or follow the instructions stated on the
selected item.
5 Press to exit.
To return to the previous setting item, press .
Default: XX
RADIO TIMER Turns on the radio at a specific time regardless of the
current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the
timer will be turned on.
2 FM / AM / SW1 / SW2 :Select the FM, AM, SW1 or SW2
band.
3 01 to 18 (for FM)/ 01 to 06 (for AM/SW1/SW2):Select
the preset station.
4 Set the activation day*
1
and time.
“
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [
OFF ] is selected for [ AM/SW1/SW2 ] in [ SRCSELECT ]
after Radio Timer for AM/SW1/SW2 is selected. (
4 )
SSM SSM01–06 / SSM07–12 / SSM13–18 :
Automatically presets up to 18 stations for FM. “SSM”
stops flashing when the first 6 stations are stored. Select
SSM07–12 / SSM13–18 to store the following 12
stations.
*1
Selectable only when [ ONCE ] or [ WEEKLY ] is selected in step 1 .
JS_JVC_KD_R862BT_U_EN_2.indd 7JS_JVC_KD_R862BT_U_EN_2.indd 7 12/8/2014 2:29:12 PM12/8/2014 2:29:12 PM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
Use a portable audio player
1 Connect a portable audio player (commercially available).
2 Select [ ON ] for [ AUX ] in [ SRC SELECT ]. ( 4 )
3 Press repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
3.5mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
AUX
Default: XX
LOCAL SEEK ON :Searches only AM/SW1/SW2 stations with good reception.;
OFF :Cancels.
• Settings made are applicable only to the selected source/station. Once
you change the source/station, you need to make the settings again.
IF BAND AUTO :Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.);
WIDE :Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
MONO ON :Improves the FM reception, but the stereo effect will be lost.;
OFF :Cancels.
NEWS-STBY *
2
ON :The unit will temporarily switch to News Programme if available.;
OFF :Cancels.
REGIONAL *
2
ON : Switches to another station only in the specific region using the “AF”
control.;
OFF :Cancels.
AF SET *
2
ON : Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor.;
OFF : Cancels.
TI SET *
2
ON : Allows the unit to temporarily switch to Traffic Information if
available (“TI” lights up). ;
OFF :Cancels.
PTY SEARCH *
2
Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
PTY code : NEWS , AFFAIRS , INFO , SPORT , EDUCATE , DRAMA , CULTURE , SCIENCE ,
VARIED , POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),
CLASSICS , OTHER M (music), WEATHER , FINANCE , CHILDREN , SOCIAL , RELIGION ,
PHONE IN , TRAVEL , LEISURE , JAZZ , COUNTRY , NATION M (music), OLDIES , FOLK M
(music),
DOCUMENT
*2
Only for FM source.
JS_JVC_KD_R862BT_U_EN_2.indd 8JS_JVC_KD_R862BT_U_EN_2.indd 8 12/8/2014 2:29:15 PM12/8/2014 2:29:15 PM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora® (Applicable for Australia or New Zealand models only)
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [
ON ] for [ PANDORA ] in [ SRC SELECT ]. ( 4 )
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
The source changes to PANDORA and broadcast starts.
To On the faceplate On the remote control
Playback / pause Press the volume knob. Press .
Skip a track Press T. Press I.
Thumbs up or
thumbs down*2
Press . Press .
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Create and save a new station
1 Press .
2 Turn the volume knob to select [ NEW STATION ], then press the knob.
3 Turn the volume knob to select [ FROM TRACK ] or [ FROM ARTIST ], then
press the knob.
A new station is created based on the current song or artist.
4 Press and hold number button 1, 4, 5or 6to store.
To select a stored station, press number button 1, 4, 5or 6.
Search for a registered station
1 Press .
2 Turn the volume knob to make a selection, then press the knob.
[
BYDATE ]: According to the registered date.
[
A-Z ]: Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold .
Bookmark a song or artist information
1 Press and hold the volume knob.
2 Turn the volume knob to make a selection, then press the knob.
[
THIS TRACK ]: Current song information
[
THIS ARTIST ]: Current artist information
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this
unit.
USB input terminal
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_R862BT_U_EN_1.indd 9JS_JVC_KD_R862BT_U_EN_1.indd 9 17/7/2014 12:00:15 PM17/7/2014 12:00:15 PM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iHeartRadio® (Applicable for Australia or New Zealand models only)
Preparation:
Install the latest version of iHeart Link for JVC application on your device (iPhone/ iPod
touch), then create an account and log in to iHeartRadio.
• Select [
ON ] for [ IHEART ] in [ SRC SELECT ]. ( 4 )
Start listening
1 Open the iHeart Link application on your device.
2 Connect your device to the USB input terminal.
3 Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically
To On the faceplate On the remote control
Playback / pause Press the volume knob. Press .
Skip a track for custom station Press T. Press I.
Thumbs up or thumbs down
for custom station*2
Press . Press .
Create a new/custom station Press and hold the volume
knob.
—
Add to favorite stations for live
station
Press 1.—
Scan for live station Press 4.—
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Search for a station
1 Press .
2 Turn the volume knob to select a category, then
press the knob.
3 Turn the volume knob to the desired station, then
press the knob.
When a city list appears, you can skip cities in
alphabetical order.
To cancel, press and hold .
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character
search.
You can search through the list quickly according to
the first character (A to Z).
2 Turn the volume knob or press to select the
character to be search for.
3 Press the volume knob to start searching.
To cancel, press and hold .
USB input terminal
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_R862BT_U_EN_1.indd 10JS_JVC_KD_R862BT_U_EN_1.indd 10 17/7/2014 12:00:15 PM17/7/2014 12:00:15 PM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pair a Bluetooth device
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit
and the device.
1 Press to turn on the unit.
2 Search and select “JVC UNIT” on the Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
• Refer also to the manual supplied with your Bluetooth device.
3 Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkey which appears on the unit and Bluetooth device is the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL–YES” “BACK–NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing. (
15)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the Bluetooth
connection is established.
• Up to five devices can be registered (paired) in total.
• Only one Bluetooth device can be connected at any time.
• This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device
to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you
reset the unit. To delete the paired device,
15 , [ DELETE PAIR ].
• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request
(via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed
the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected devcie is turned on.
– [
AUTO CNNT ] is set to [ ON ]. ( 15 )
– JVC MUSIC PLAY application is installed on the Android device.
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the microphone
angle
Secure using cord clamps
(not supplied) if necessary.
Microphone input jack
Microphone
(supplied)
Rear panel
JS_JVC_KD_R862BT_U_EN_2.indd 11JS_JVC_KD_R862BT_U_EN_2.indd 11 7/8/2014 10:45:22 AM7/8/2014 10:45:22 AM

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
– All the buttons flash.
– The unit answers the call automatically if [
AUTO ANSWER ] is set to a selected time. (  13 )
During a call:
– If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
To On the faceplate On the remote control
Answer a call Press or the volume knob. Press .
Reject a call Press and hold or the volume
knob.
Press and hold .
End a call Press and hold or the volume
knob.
Press and hold .
Adjust the phone
volume
[
00 ] to [ 50 ] (Default: [ 15 ]*)
Turn the volume knob during a call.
• This adjustment will not affect the
volume of the other sources.
—
Switch between hands-
free and private talk
modes
Press the volume knob during a call.
• Operations may vary according to the
connected Bluetooth mobile phone.
—
* Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.
Improve the voice quality
While talking on the phone....
1 Press and hold .
2 Turn the volume knob to make a selection
( see the following table ) , then press the
knob.
3 Repeat step 2until the desired item is
selected or activated.
4 Press to exit.
To return to the previous setting item, press
.
Default:
XX
MIC LEVEL –10
— +10 ( –4 ):The sensitivity of
the microphone increases as the number
increased.
NOISE RDCT –5 — +5 ( 0 ):Adjust the noise reduction
level until the least noise is being heard
during a phone conversation.
ECHO CANCEL –5 — +5 ( 0 ):Adjust the echo
cancellation delay time until the least
echo is being heard during a phone
conversation.
BLUETOOTH®
JS_JVC_KD_R862BT_U_EN_f.indd 12JS_JVC_KD_R862BT_U_EN_f.indd 12 25/8/2014 4:08:11 PM25/8/2014 4:08:11 PM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also
possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to make a selection (see the following table), then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow the instructions stated on
the selected item.
To return to the previous setting item, press .
RECENT CALL
1 Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the volume knob to call.
PHONEBOOK
1 Press to select the desired letter (A to Z, 0to9, and OTHERS).
• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the
unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Turn the volume knob to make a selection
(see the following table), then press the
knob.
3 Repeat step 2until the desired item is
selected or activated.
To return to the previous setting item, press
.
Default:
XX
SETTINGS
AUTO ANSWER 01 SEC
— 30 SEC :The unit answers
incoming call automatically in
the selected time (in seconds).;
OFF :Cancels.
BLUETOOTH®
JS_JVC_KD_R862BT_U_EN_1.indd 13JS_JVC_KD_R862BT_U_EN_1.indd 13 7/8/2014 10:14:24 AM7/8/2014 10:14:24 AM

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DIAL NUMBER 1 Turn the volume knob to select a number (0 to 9) or character ( , #,
+).
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
VOICE Speak the name of the contact you want to call or the voice command to
control the phone functions.
(  Make a call using voice recognition )
Make a call using voice recognition
1 Press and hold to activate the connected phone.
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of
iPhone.
Delete a contact
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [ RECENTCALL ], then press the knob.
3 Turn the volume knob to select a contact.
4 Press and hold to enter delete mode.
5 Turn the volume knob to select [ DELETE ] or [ DELETE ALL ], then press
the knob.
DELETE : Selected name or phone number in step 3is deleted.
DELETE ALL : All names or phone numbers in [ RECENTCALL ]in step 2is
deleted.
6 Turn the volume knob to select [ YES ], then press the knob.
• To return to the previous setting item, press .
• Not applicable for mobile phone that supports PBAP.
BLUETOOTH®
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1to 6).
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [ RECENTCALL ], [ PHONEBOOK ], or
[
DIALNUMBER ], then press the knob.
3 Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
4 Press and hold one of the number buttons (1to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select [
DIALNUMBER ] in step 2
and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1to 6).
3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
Bluetooth mode settings
1 Press and hold .
2 Turn the volume knob to select [ BLUETOOTH ], then press the knob.
3 Turn the volume knob to make a selection ( 15) , then press the
knob.
4 Repeat step 3until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_R862BT_U_EN_1.indd 14JS_JVC_KD_R862BT_U_EN_1.indd 14 7/8/2014 10:14:27 AM7/8/2014 10:14:27 AM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold .
“BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING
PHONE” “PIN IS 0000” scrolls on the display.
2 Search and select “JVC UNIT” on the Bluetooth device within
3minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same
passkey appears on the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” “[Device Name]” appears and
Bluetooth compatibility check starts.
If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device
to allow phonebook access to continue.
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*1and/or “A.STREAM OK”*2and/or
“PBAP OK”*3: Compatible
*1
Compatible with Hands-Free Profile (HFP)
*2
Compatible with Advanced Audio Distribution Profile (A2DP)
*3
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has
been deleted, and the unit exits check mode.
• To cancel, press and hold to turn off the power, then turn
on the power again.
Default: XX
PHONE *1 Selects the phone or audio device to connect or disconnect.
“” appears in front of the device name when connected.
AUDIO *1
APPLICATION *1 Shows the connected phone name using the JVC Smart Music Control * 2
app. “ ” appears in front of the device name when connected.
DELETE PAIR 1 Turn the volume knob to select a device to delete, then press the
knob.
2 Turn the volume knob to select [ YES ] or [ NO ], then press the knob.
SET PINCODE
(0000)
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the PIN code.
3 Press the volume knob to confirm.
AUTO CNNCT ON :The unit automatically reconnect when the last connected
Bluetooth device is within range.;
OFF :Cancels.
AUTO PAIR ON :The unit automatically pair supported Bluetooth device (iPhone/
iPod touch/ Android device) when it is connected through USB input
terminal.Depending on the operating system of the connected device,
this function may not work. ;
OFF :Cancels.
INITIALIZE YES :Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.).;
NO :Cancels.
INFORMATION MY  BT  NAME : Displays the unit name (JVCUNIT).;
MY  ADDRESS : Shows address of this unit.
*1
You can only connect another Bluetooth device by disconnecting the connected Bluetooth
device first. “ ” disappears when disconnected.
*2
JVC Smart Music Control is designed to view JVC car receiver status and perform simple
control operations on Android smart phones.
For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>.
JS_JVC_KD_R862BT_U_EN_2.indd 15JS_JVC_KD_R862BT_U_EN_2.indd 15 8/8/2014 3:48:56 PM8/8/2014 3:48:56 PM

16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Internet radio via Bluetooth
Listen to Pandora
Preparation:
Select [
ON ] for [ PANDORA ] in [ SRC SELECT ]. ( 4)
You can listen to Pandora on your smart phone
(Android OS) through Bluetooth on this unit.
1 Open the Pandora application on your device.
2 Connect your Bluetooth audio player via
Bluetooth connection. ( 
11 )
3 Press repeatedly to select PANDORA.
The source switches and broadcast starts
automatically.
You can operate Pandora in the same way as Pandora
for iPod/iPhone. ( 
9 )
Listen to iHeartRadio
Preparation:
Select [
ON ] for [ IHEART ] in [ SRC SELECT ]. ( 4)
You can listen to iHeartRadio on your smart phone
(Android OS) through Bluetooth on this unit.
1 Open the iHeart Link application on your smart
phone.
2 Connect your smart phone via Bluetooth
connection. (
11 )
3 Press repeatedly to select
IHEARTRADIO.
The source switches and broadcast starts
automatically.
You can operate iHeartRadio in the same way as
iHeartRadio for iPod/iPhone. ( 
10 )
BLUETOOTH — Audio
Audio player via Bluetooth
1 Press repeatedly to select BTAUDIO (or press SOURCE on RM-RK52).
2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback / pause Press .Press .
Select group or folder Press . Press .
Reverse /
Forward skip
Press .Press .
Reverse / Fast-forward Press and hold .Press and hold .
Repeat play Press repeatedly.
TRACKRPT , ALLRPT , RPTOFF
—
Random play Press repeatedly.
GROUPRND , ALLRND , RNDOFF
—
Operations and display indications may differ according to their availability on the
connected device.
JS_JVC_KD_R862BT_U_EN_1.indd 16JS_JVC_KD_R862BT_U_EN_1.indd 16 17/7/2014 12:00:17 PM17/7/2014 12:00:17 PM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
Default: XX
EQSETTING
EQPRESET FLAT
/ HARD ROCK / JAZZ / POP / R&B / TALK / USER1 / USER2 /
VOCALBOOST / BASSBOOST / CLASSICAL / DANCE :Selects a preset
equalizer.
EASYEQ 1 USER1 / USER2 :Select a preset name.
2 Adjust your own sound settings.
SUB.W SP
*1*2
: 00 to +06 (Default: 03
SUB.W
*1*3
: –08 to +08 00
BASS  LVL : –06 to +06 00
MID  LVL: –06 to +06 00
TRE  LVL : –06 to +06 00 )
PRO EQ 1 USER1 / USER2 :Select a preset name.
2 BASS / MIDDLE / TREBLE :Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
BASS Frequency: 60 / 80 / 100 / 200HZ
(
Default: 80HZ
Level: –06 to +06 00
Q: Q1.0 / Q1.25 / Q1.5 / Q2.0 Q1.0 )
MIDDLE Frequency: 0.5 / 1.0 / 1.5 / 2.5KHZ (Default: 1.0KHZ
Level: –06 to +06 00
Q: Q0.75 / Q1.0 / Q1.25 Q1.25 )
TREBLE Frequency: 10.0 / 12.5 / 15.0 / 17.5KHZ (Default: 10.0KHZ
Level: –06 to +06 00
Q: QFIX QFIX )
*1
Displayed only when [ SUB.W ] is set to [ ON ]. (  18 )
*2
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ]. (  18 )
*3
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ]. (  18 )
To On the faceplate
Select a preset
equalizer
Press repeatedly.
Press , then turn the volume knob
within 2seconds.
Preset equalizer : FLAT (default), HARD ROCK , JAZZ , POP ,
R&B , TALK , USER1 , USER2 , VOCAL BOOST , BASS BOOST ,
CLASSICAL , DANCE
Store your own
sound settings
1 Press and hold .
2 Turn the volume knob to select [ EASY EQ ], then
press the knob.
3 Turn the volume knob to select [ USER1 ] or
[
USER2 ], then press the knob.
4 Turn the volume knob to make a selection,
then press the knob.
For settings, refer to step 2of [
EASYEQ ].
• To return to the previous setting item, press .
• To exit, press .
Other settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_R862BT_U_EN_2.indd 17JS_JVC_KD_R862BT_U_EN_2.indd 17 7/8/2014 3:00:28 PM7/8/2014 3:00:28 PM

18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO
BASS BOOST +01
/ +02 : Selects your preferred bass boost level.; OFF :Cancels.
LOUD 01 / 02 :Boosts low or high frequencies to produce a well-balanced
sound at low volume.;
OFF :Cancels.
SUB.W LEVEL
*4
SPK-OUT
*5
00 to +06 ( +03 ):Adjusts the output level of the
subwoofer connected via speaker lead. (
 25 )
PRE-OUT
*6
–08 to +08 ( 00 ):Adjusts the output level of the
subwoofer connected to the lineout terminals (REAR/
SW) through an external amplifier. (
 25 )
SUB.W
*6
ON / OFF : Turns on or off the subwoofer output.
SUB.W  LPF
*4
THROUGH :All signals are sent to the subwoofer. ; LOW  55HZ /
MID  85HZ / HIGH120HZ :Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.WPHASE
*4
REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [
THROUGH ] is selected for
[
SUB.W  LPF ].)
FADER R06 — F06 ( 00 ):Adjusts the front and rear speaker output balance.
BALANCE
*7
L06 — R06 ( 00 ):Adjusts the left and right speaker output balance.
VOL ADJUST –05 — +05 ( 00 ):Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP GAIN LOW  POWER :Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGHPOWER :The maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF :Cancels.
SPK/PRE  OUT Selects the appropriate setting to get the desired output. ( See the
following table
.)
*4
Displayed only when [ SUB.W ] is set to [ ON ].
*5
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ].
*6
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ].
*7
This adjustment will not affect the subwoofer output.
SPK/PRE OUT
Connection via lineout terminals (  25 )
Setting Lineout terminal
FRONT REAR/SW
REAR/REAR Front speakers output Rear speakers output
REAR/SUB.W Front speakers output Subwoofer output
SUB.W/SUB.W Front speakers output Subwoofer output
Connection via speaker leads (  25 )
Setting Rear speaker lead
L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output
REAR/SUB.W Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output (Mute)
If [ SUB.W/SUB.W ] is selected:
– [
HIGH120HZ ] is selected in [ SUB.W  LPF ] and [ THROUGH ] is not available.
– [
R01 ] is selected in [ FADER ] and selectable range is [ R06 ]to [ 00 ]
AUDIO SETTINGS
JS_JVC_KD_R862BT_U_EN_1.indd 18JS_JVC_KD_R862BT_U_EN_1.indd 18 7/8/2014 10:14:43 AM7/8/2014 10:14:43 AM

ENGLISH 19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: XX
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the [ BRIGHTNESS ]
setting.
OFF :Selects the day adjustments.; ON :Selects the night adjustments.;
DIMMER TIME :Adjusts the dimmer on and off time.
Turn the volume knob to adjust the [
ON ] time, then press the knob.
Turn the volume knob to adjust the [
OFF ] time, then press the knob.
(Default: [
ON ]: 18:00 or 6:00 PM
[
OFF ]: 6:00 or 6:00 AM)
AUTO :Changes between the day and night adjustments when you turn off or
on the car headlights.*
1
BRIGHTNESS Sets the button and display brightness for day and night separately.
1 DAY / NIGHT :Select day or night.
2 Select a zone for setting. ( Illustration above )
3 Set the brightness level ( 00 to 31 ). (Default: DAY : 31 ; NIGHT : 15 )
SCROLL * 2 ONCE :Scrolls the display information once.; AUTO :Repeats scrolling at
5-second intervals.;
OFF :Cancels.
*1
The illumination control wire connection is required. ( 25 )
*2
Some characters or symbols will not be shown correctly (or will be blanked).
DISPLAY SETTINGS
About discs and audio files
• This unit can only play the following CDs:
• This unit can play back multi-session discs; however, unclosed sessions will be skipped
during playback.
•
Unplayable discs:
- Discs that are not round.
- Discs with coloring on the recording surface or discs that are dirty.
- Recordable/ReWritable discs that have not been finalized.
- 8 cm CD. Attempting to insert using an adapter may cause malfunction.
•
DualDisc playback: The Non-DVD side of a “DualDisc” does not comply with the “Compact
Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product
cannot be recommended.
•
Playable files:
- File extensions: MP3(.mp3), WMA(.wma), AAC (.m4a)
- Bit rate: MP3: 8kbps — 320kbps
WMA: 32kbps — 192kbps
AAC: 8kbps — 320kbps
- Sampling frequency:
MP3: 48kHz, 44.1kHz, 32kHz, 24kHz, 22.05kHz, 16kHz, 12kHz, 11.025kHz, 8kHz
WMA: 8kHz — 48kHz
AAC: 8kHz — 48kHz
- Variable bit rate (VBR) files.
•
Maximum number of characters for file/folder name:
It depends on the disc format used (includes 4 extension characters—<.mp3>, <.wma> or
<.m4a>).
- ISO 9660 Level 1 and 2: 32 characters
- Romeo: 32 characters
- Joliet: 32 characters
- Windows long file name: 32 characters
MORE INFORMATION
JS_JVC_KD_R862BT_U_EN_1.indd 19JS_JVC_KD_R862BT_U_EN_1.indd 19 7/8/2014 10:14:43 AM7/8/2014 10:14:43 AM

20
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
About USB devices
• This unit can play MP3/WMA/AAC/WAV files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- AAC Tag: 64 characters
- WAV Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder
without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• It is not possible to browse video files on the “Videos” menu in
[HEAD MODE] .
• The song order displayed on the selection menu of this unit may differ from that of the iPod/
iPhone.
• If some operations are not performed correctly or as intended, visit:
<http://www.jvc.net/cs/car/>.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory
(AOA)2.0.
• If the Android device supports both mass storage class device and AOA2.0, this unit always
playback via AOA2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>.
About Pandora
• Pandora is available only in the U.S., Australia and New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired, or some or all of the services may
become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at [email protected].
About iHeartRadio
• iHeartRadio® is available only in the U.S., Australia and New Zealand.
• iHeartRadio® is a third-party service, therefore the specifications are subject to change
without prior notice. Accordingly, compatibility may be impaired or some or all of the
services may become unavailable.
• Some functions of iHeartRadio® cannot be operated from this unit.
About Bluetooth
• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able
to connect to this unit.
• This unit may not work with some Bluetooth devices.
• Signal conditions vary, depending on the surroundings.
• For more information about Bluetooth, visit the following JVC website:
<http://www.jvc.net/cs/car/>.
About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and Android
TM
application JVC Music
Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music
Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site:
<http://www.jvc.net/cs/car/>.
MORE INFORMATION
JS_JVC_KD_R862BT_U_EN_1.indd 20JS_JVC_KD_R862BT_U_EN_1.indd 20 17/7/2014 12:00:19 PM17/7/2014 12:00:19 PM