JVC KD-R951BT User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
FRANÇAIS
GET0983-001A [E/EN]
KD-R951BT / KD-R852BT / KD-R851BT
CD RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR CD
MANUEL D’INSTRUCTIONS
Please read all instructions carefully before
operation to obtain the best possible performance
from the unit.
Veuillez lires les instructions attentivement avant
d’utiliser l’appareil afin d’obtenir les meilleures
performances possibles de l’appareil.
JS_JVC_KD_R951BT_E_C001A.indd 1JS_JVC_KD_R951BT_E_C001A.indd 1 12/3/2013 12:11:15 PM12/3/2013 12:11:15 PM
Downloaded from www.vandenborre.be

i
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household
waste.
Old electrical and electronic equipment and batteries should be recycled at a facility capable of
handling these items and their waste byproducts.
Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling
and waste disposal will help conserve resources whilst preventing detrimental effects on our health
and the environment.
Notice: The sign “Pb” below the symbol for batteries indicates that this battery contains lead.
Information sur l’élimination des anciens équipements électriques et électroniques et piles
électriques (applicable dans les pays de l’Union Européenne qui ont adopté des systèmes de
collecte sélective)
Les produits et piles électriques sur lesquels le pictogramme (poubelle barrée) est apposé ne
peuvent pas être éliminés comme ordures ménagères.
Les anciens équipements électriques et électroniques et piles électriques doivent être recyclés sur
des sites capables de traiter ces produits et leurs déchets.
Contactez vos autorités locales pour connaître le site de recyclage le plus proche. Un recyclage
adapté et l’élimination des déchets aideront à conserver les ressources et à nous préserver des leurs
effets nocifs sur notre santé et sur l’environnement.
Remarque: Le symbole “Pb“ ci-dessous sur des piles électrique indique que cette pile contient du
plomb.
For Israel
The marking of products using lasers
The label is attached to the chassis/case and says that the component uses laser beams that have been classified
as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous
radiation outside the unit.
Marquage des produits utilisant un laser
L’étiquette est attachée au châssis/boîtier de l’appareil et indique que l’appareil utilise des rayons laser de
classe 1. Cela signifie que l’appareil utilise des rayons laser d’une classe faible. Il n’y a pas de danger de radiation
accidentelle hors de l’appareil.
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC
Declaration of Conformity with regard to the EMC Directive 2004/108/EC
Declaration of Conformity with regard to the RoHS Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
EU Representative:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany
Déclaration de conformité vis à vis de la Directive 1999/5/CE de R&TTE
Déclaration de conformité se rapportant à la directive EMC 2004/108/EC
Déclaration de conformité se rapportant à la directive RoHS 2011/65/EU
Fabricant:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
Représentants dans l’UE:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany
JS_JVC_KD_R951BT_E_S001A.indd iJS_JVC_KD_R951BT_E_S001A.indd i 12/9/2013 4:00:11 PM12/9/2013 4:00:11 PM
Downloaded from www.vandenborre.be

ii
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
English
Hereby, JVC KENWOOD declares that this
unit KD-R951BT/KD-R852BT/KD-R851BT is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
Français
Par la présente JVC KENWOOD déclare que
l’appareil KD-R951BT/KD-R852BT/KD-R851BT est
conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Par la présente, JVC KENWOOD déclare que
ce KD-R951BT/KD-R852BT/KD-R851BT est
conforme aux exigences essentielles et aux autres
dispositions de la directive 1999/5/CE qui lui sont
applicables.
Deutsch
Hiermit erklärt JVC KENWOOD, dass sich
dieser KD-R951BT/KD-R852BT/KD-R851BT in
Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet.
(BMWi)
Hiermit erklärt JVC KENWOOD die
Übereinstimmung des Gerätes KD-R951BT/
KD-R852BT/KD-R851BT mit den grundlegenden
Anforderungen und den anderen relevanten
Festlegungen der Richitlinie 1999/5/EG. (Wien)
Nederlands
Hierbij verklaart JVC KENWOOD dat het
toestel KD-R951BT/KD-R852BT/KD-R851BT in
overeenstemming is met de essentiële eisen en
de andere relevante bepalingen van richtlijn
1999/5/EG.
Bij deze verklaat JVC KENWOOD dat deze
KD-R951BT/KD-R852BT/KD-R851BT voldoet aan
de essentiële eisen en aan de overige relevante
bepalingen van Richtlijn 1999/5/EC.
Italiano
Con la presente JVC KENWOOD dichiara che questo
KD-R951BT/KD-R852BT/KD-R851BT è conforme
ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Español
Por medio de la presente JVC KENWOOD declara
que el KD-R951BT/KD-R852BT/KD-R851BT cumple
con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva
1999/5/CE.
Português
JVC KENWOOD declara que este KD-R951BT/
KD-R852BT/KD-R851BT está conforme com os
requisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Polska
JVC KENWOOD niniejszym oświadcza, że
KD-R951BT/KD-R852BT/KD-R851BT spełnia
zasadnicze wymogi oraz inne istotne
postanowienia dyrektywy 1999/5/EC.
Český
JVC KENWOOD tímto prohlašuje, že tento
KD-R951BT/KD-R852BT/KD-R851BT je ve shodě
se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Magyar
Alulírott, JVC KENWOOD, kijelenti, hogy a jelen
KD-R951BT/KD-R852BT/KD-R851BT megfelel
az 1999/5/EC irányelvben meghatározott
alapvető követelményeknek és egyéb vonatkozó
előírásoknak.
Svenska
Härmed intygar JVC KENWOOD att denna
KD-R951BT/KD-R852BT/KD-R851BT stär l
överensstämelse med de väsentliga egenskapskrav
och övriga relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Suomi
JVC KENWOOD vakuuttaa täten että KD-R951BT/
KD-R852BT/KD-R851BT tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten
ja sitä koskevien direktiivin muiden ehtojen
mukainen.
Slovensko
S tem JVC KENWOOD izjavlja, da je ta KD-R951BT/
KD-R852BT/KD-R851BT v skladu z osnovnimi
zahtevami in ostalimi ustreznimi predpisi Direktive
1999/5/EC.
Slovensky
Spoločnosť JVC KENWOOD týmto vyhlasuje,
že KD-R951BT/KD-R852BT/KD-R851BT spĺňa
zákldné požiadavky a ďalšie prislušné ustanovenia
Direktĺvy 1999/5/EC.
Dansk
Undertegnede JVC KENWOOD erklærer harved,
at følgende udstyr KD-R951BT/KD-R852BT/
KD-R851BT overholder de væsentlige krav og
øvrige relevante krav i direktiv 1999/5/EF.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ JVC KENWOOD ΔΗΛΩΝΕΙ
ΟΤΙ KD-R951BT/KD-R852BT/KD-R851BT
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ
ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/EK.
Eesti
Sellega kinnitab JVC KENWOOD, et see KD-R951BT/
KD-R852BT/KD-R851BT vastab direktiivi 1999/5/EC
põhilistele nõudmistele ja muudele asjakohastele
määrustele.
Latviešu
Ar šo, JVC KENWOOD, apstiprina, ka KD-R951BT/
KD-R852BT/KD-R851BT atbilst Direktīvas
1999/5/EK galvenajām prasībām un citiem tās
nosacījumiem.
Lietuviškai
Šiuo, JVC KENWOOD, pareiškia, kad šis KD-R951BT/
KD-R852BT/KD-R851BT atitinka pagrindinius
Direktyvos 1999/5/EB reikalavimus ir kitas svarbias
nuostatas.
Malti
Hawnhekk, JVC KENWOOD, jiddikjara li dan
KD-R951BT/KD-R852BT/KD-R851BT jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Українська
Компанія JVC KENWOOD заявляє, що цей виріб
KD-R951BT/KD-R852BT/KD-R851BT відповідає
ключовим вимогам та іншим пов’язаним
положенням Директиви 1999/5/EC.
Turkish
Bu vesileyle JVC KENWOOD, KD-R951BT/
KD-R852BT/KD-R851BT ünitesinin, 1999/5/EC
Direktifinin başlıca gereksinimleri ve diğer ilgili
hükümleri ile uyumlu olduğunu beyan eder.
JS_JVC_KD_R951BT_E_S001A.indd iiJS_JVC_KD_R951BT_E_S001A.indd ii 12/3/2013 12:10:57 PM12/3/2013 12:10:57 PM
Downloaded from www.vandenborre.be

2
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CONTENTS BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the USB device or iPod/iPhone if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
•
Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to
evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate.
( 3)
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
CD / USB / iPod 5
RADIO 7
AUX 8
BLUETOOTH® 9
AUDIO SETTINGS 13
DISPLAY SETTINGS 15
MORE INFORMATION 16
TROUBLESHOOTING 17
SPECIFICATIONS 19
INSTALLATION /
CONNECTION 20
How to read this manual
• Operations are explained mainly
using buttons on the faceplate of
KD-R852BT / KD-R851BT .
• English language is used for
the display explanation in this
manual.
•
[XX] indicates the selected items.
•
( XX) indicates references are
available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse
side of the faceplate)
JS_JVC_KD_R951BT_E_02_EN.indd 2JS_JVC_KD_R951BT_E_02_EN.indd 2 12/9/2013 4:02:35 PM12/9/2013 4:02:35 PM
Downloaded from www.vandenborre.be

3
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASICS
To Do this (on the faceplate) Do this (on the remote control)
Turn on the power Press B/SOURCE.
• Press and hold to turn off the power. ( not available )
Adjust the volume Turn the volume knob. Press VOL + or VOL –.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press B/SOURCE repeatedly.
• Press B/SOURCE, then turn the volume knob within 2 seconds.
Press SOURCE repeatedly.
Change the display
information
Press DISP repeatedly.
( 17)
• Press and hold to scroll the current display information. ( not available )
Attach
How to reset
Detach
Your preset adjustments
will also be erased.
Remote control (RM-RK52) (not supplied)
KD-R951BT can be remotely controlled with an
optionally purchased remote control.
Faceplate
KD-R951BT
KD-R951BT
Volume knob
(turn/press) Loading slot
Detach
button
Display window
ENGLISH |
How to replace the battery
Pull out the insulation sheet
when using for the first time.
Remote sensor (Do not expose
to bright sunlight.)
JS_JVC_KD_R951BT_E_05_EN.indd 3JS_JVC_KD_R951BT_E_05_EN.indd 3 12/16/2013 10:26:38 AM12/16/2013 10:26:38 AM
Downloaded from www.vandenborre.be

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
1 Press and hold MENU.
2 Turn the volume knob to select [DEMO] , then press the knob.
3 Turn the volume knob to select [DEMO OFF] , then press the knob.
4 Press MENU to exit.
Set the clock
1 Press and hold MENU.
2 Turn the volume knob to select [CLOCK] , then press the knob.
3 Turn the volume knob to select [CLOCK SET] , then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [24H/ 12H] , then press the knob.
6 Turn the volume knob to select [12 HOUR] or [24 HOUR] , then press the
knob.
7 Press MENU to exit.
Set the basic settings
1 Press and hold MENU.
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Press MENU to exit.
To return to the previous setting item or hierarchy, press GT/P.
1
2
Default: XX
CLOCK
CLOCK ADJ AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Data System signal.;
OFF :Cancels.
CLOCK DISP ON :The clock time is shown on the display even when the unit is turned
off.;
OFF :Cancels.
SETTINGS
BEEP ON
:Activates the keypress tone.; OFF :Deactivates.
SRC SELECT
AM
* ON :Enables AM in source selection.; OFF :Disables.
AUX * ON :Enables AUX in source selection.; OFF :Disables.
LANGUAGE Selects the display language for menu and Tag information (folder name,
file name, song title, artist name, album name) if applicable.
ENGLISH :Display language is English.
РУССКИЙ :Display language is Russian.
F/W UPDATE
SYSTEM / BLUETOOTH
F/W xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
* Not displayed when the corresponding source is selected.
3
JS_JVC_KD_R951BT_E_02_EN.indd 4JS_JVC_KD_R951BT_E_02_EN.indd 4 12/3/2013 12:11:26 PM12/3/2013 12:11:26 PM
Downloaded from www.vandenborre.be

5
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD / USB / iPod
To Do this
Select a track/file Press S/T(or press H/Ion RM-RK52).
Select a folder *3Press 1K/2J(or press J/Kon RM-RK52).
Reverse/
Fast-forward
Press and hold S/T(or press and hold H/Ion RM-RK52).
Repeat play *4Press 4Brepeatedly to make a selection.
• Audio CD or JVC Playlist Creator (JPC) / JVC Music Control (JMC) file ( 16) :
TRACKRPT, RPT OFF
• MP3/WMA/WAV file: TRACKRPT, FOLDER RPT, RPT OFF
• iPod: ONE RPT, ALL RPT, RPT OFF
Random play *4Press 3Arepeatedly to make a selection.
• Audio CD: ALL RND, RND OFF
• MP3/WMA/WAV file or JPC / JMC file: FOLDERRND, ALL RND, RND OFF
• iPod: SONG RND, ALL RND, RND OFF
*1Do not leave the cable inside the car when not using.
*2You can still play/pause, file skip, fast forward or reverse files from the unit.
*3Only for MP3/WMA/WAV files. This does not work for iPod.
*4For iPod: Applicable under
[HEAD MODE] only.
Start playback
The source changes automatically and
playback starts.
CD
USB
iPod/iPhone
Press 5 iPod MODE repeatedly to select the
control mode (
[HEAD MODE] / [IPHONE MODE] ).
HEAD MODE : From the unit.
IPHONE MODE : From the iPod/iPhone.*2
Eject disc Label side
USB input terminal
USB input terminal USB 2.0 cable
*1
(commercially available)
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_R951BT_E_04_EN.indd 5JS_JVC_KD_R951BT_E_04_EN.indd 5 12/12/2013 10:42:15 AM12/12/2013 10:42:15 AM
Downloaded from www.vandenborre.be

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select a track/file from a list
For iPod: Applicable only when [HEAD MODE] is selected. ( 5)
1 Press MENU.
2 Turn the volume knob to make a selection, then press the knob.
• MP3/WMA/WAV file: Select the desired folder, then a file.
• iPod or JPC / JMC file: Select the desired file from the list (PLAYLISTS,
ARTISTS, ALBUMS, SONGS, PODCASTS*, GENRES, COMPOSERS*,
AUDIOBOOKS*).
*
Only for iPod.
If you have many files....
You can search through them quickly (on step 2above) by turning the
volume knob quickly.
• Not applicable for iPod.
Select a song by name
While listening to the iPod and [HEAD MODE] is selected ( 5) ....
If you have many folders or tracks/files, you can search through them
quickly according to the first character (A to Z, 0 to 9 and OTHERS).
• “OTHERS” appear if the first character is other than Ato Z, 0 to 9.
1 Press MENU.
2 Turn the volume knob to select the desired list, then press the
knob.
3 Press 1K/2Jor turn the volume knob quickly to select the desired
character.
4 Turn the volume knob to select the desired folder or track/file, then
press the knob.
Change the USB drive
When a smartphone (Mass Storage Class) is connected to the USB input
terminal, you can select its internal memory or external memory (such as an
SD card) to playback the stored songs.
You can also select the desired drive to playback when a multiple drives
device is connected.
Press 5 iPod MODE repeatedly to select the desired drive.
(or)
1 Press and hold MENU.
2 Turn the volume knob to select [USB/IPOD] , then press the knob.
3 Turn the volume knob to select [USB] , then press the knob.
4 Press the volume knob to select [DRIVECHANGE] .
The next drive is selected automatically.
Repeat steps 1to 4to select the following drives.
Selectable items:
[DRIVE  1] to [DRIVE  5]
Change the playback speed of the Audiobook
While listening to the iPod and [HEAD MODE] is selected ( 5) ....
1 Press and hold MENU.
2 Turn the volume knob to select [USB/IPOD] , then press the knob.
3 Turn the volume knob to select [IPOD] , then press the knob.
4 Turn the volume knob to make a selection, then press the knob.
BOOK NORMAL / BOOK FASTER / BOOK SLOWER : Select the desired playback
speed of the Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
• To return to the previous setting item or hierarchy, press GT/P.
• To cancel, press MENU.
CD / USB / iPod
JS_JVC_KD_R951BT_E_02_EN.indd 6JS_JVC_KD_R951BT_E_02_EN.indd 6 12/9/2013 4:02:44 PM12/9/2013 4:02:44 PM
Downloaded from www.vandenborre.be

7
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient
signal strength.
Search for a station
1 Press B/SOURCE to select FM or AM.
2 Press S/T(or press H/Ion RM-RK52) to search for a station
automatically.
(or)
Press and hold S/T(or press and hold H/Ion RM-RK52) until
“M” flashes, then press repeatedly to search for a station manually.
Store a station
You can store up to 18 stations for FM and 6 stations for AM.
While listening to a station....
Press and hold one of the number buttons (1to 6) to store.
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the
knob.
The preset number flashes and “MEMORY” appears.
• To select a stored station: Press one of the number buttons (1to6).
(or)
Press MENU, then turn the volume knob to select a preset number and
press the knob to confirm.
Search for your favorite program (PTY Search)
Available only for FM source.
1 Press and hold GT/P.
2 Turn the volume knob to select a PTY code, then press the knob to
start searching.
If there is a station broadcasting a program of the same PTY code as
you have selected, that station is tuned in.
PTY code: NEWS , AFFAIRS , INFO , SPORT , EDUCATE , DRAMA , CULTURE , SCIENCE , VARIED ,
POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS , OTHER M
(music),
WEATHER , FINANCE , CHILDREN , SOCIAL , RELIGION , PHONE IN , TRAVEL , LEISURE ,
JAZZ , COUNTRY , NATION M (music), OLDIES , FOLK M (music), DOCUMENT
Activate TA Standby Reception
Available only for FM source.
Press GT/P.
The unit will temporarily switch to Traffic Announcement (TA) (if
available) from any source other than AM.
• To deactivate, press GT/P again.
Other settings
1 Press and hold MENU.
2 Turn the volume knob to select [TUNER] , then press the knob.
3 Turn the volume knob to make a selection ( 8) , then press the
knob.
4 Press MENU to exit.
To return to the previous setting item or hierarchy, press GT/P.
JS_JVC_KD_R951BT_E_02_EN.indd 7JS_JVC_KD_R951BT_E_02_EN.indd 7 12/3/2013 12:11:28 PM12/3/2013 12:11:28 PM
Downloaded from www.vandenborre.be

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
Use a portable audio player
1 Connect a portable audio player
(commercially available).
2 Select [ON] for [AUX] in [SRC SELECT] . ( 4)
3 Press B/SOURCE to select AUX.
4 Turn on the portable audio player and
start playback.
Use a 3-core plug head stereo mini
plug for optimum audio output.
3.5mm stereo mini plug with “L” shaped
connector (commercially available)
Portable audio
player
Auxiliary input jack
AUX
Default: XX
RADIO TIMER Turns on the radio at a specific time regardless of the current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the timer will be turned on.
2 FM / AM :Select the FM or AM band.
3 01 to 18 (for FM)/ 01 to 06 (for AM):Select the preset station.
4 Set the activation day*
1
and time.
• “
M ” lights up when complete.
*
1
Selectable only when [ONCE] or [WEEKLY] is selected in step 1 .
Radio Timer will not activate for the following cases.
• The unit is turned off.
•
[OFF] is selected for [AM] in [SRC SELECT] after Radio Timer for AM is selected. ( 4)
SSM SSM 01 – 06
/ SSM 07 – 12 / SSM 13 – 18 :Automatically presets up to 18 stations for FM. “SSM” stops
flashing when the first 6 stations are stored. Select
SSM 07 – 12 / SSM 13 – 18 to store the following 12
stations.
IF BAND *2 AUTO :Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo
effect may be lost.);
WIDE :Subjects to interference noises from adjacent FM stations, but sound quality
will not be degraded and the stereo effect will remain.
MONO *2 ON :Improves the FM reception, but the stereo effect will be lost.; OFF :Cancels.
NEWS-STBY *2 ON :The unit will temporarily switch to News Programme if available.; OFF :Cancels.
REGIONAL *2 ON : Switches to another station only in the specific region using the “AF” control.; OFF :Cancels.
AF SET *2 ON : Automatically searches for another station broadcasting the same program in the same Radio Data
System network with better reception when the current reception is poor.;
OFF : Cancels.
*2Only for FM source.
JS_JVC_KD_R951BT_E_02_EN.indd 8JS_JVC_KD_R951BT_E_02_EN.indd 8 12/3/2013 2:25:24 PM12/3/2013 2:25:24 PM
Downloaded from www.vandenborre.be

9
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Pair a Bluetooth device
When connecting a Bluetooth device to the
unit for the first time, perform pairing between
the unit and the device. Once the pairing is
completed, the Bluetooth device will remain
registered in the unit even if you reset the unit.
• Up to five devices can be registered (paired)
in total.
• A maximum of two Bluetooth phones and
one Bluetooth audio device can be connected
at any time.
•
This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not
automatically connect to the unit after
pairing. Connect the device to the unit
manually. Refer to the instruction manual of
the Bluetooth device for more information.
1 Press B/SOURCE to turn on the unit.
2 Search and select “JVC UNIT” on the
Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may
need to enter the Personal Identification
Number (PIN) code immediately after
searching.
3 Perform (A) or (B) depending on what
scrolls on the display.
• For some Bluetooth devices, pairing
sequence may vary from the steps
described below.
(A) “[Device Name]” “XXXXXX”
“VOL–YES” “BACK–NO”
• “XXXXXX” is a 6-digit passkey randomly
generated during each pairing.
You can operate Bluetooth devices using this
unit.
Connect the microphone
If you turn off the unit or detach the control
panel during a phone call conversation,
the Bluetooth connection is disconnected.
Continue the conversation using your mobile
phone.
Supported Bluetooth profiles
– Hands-Free Profile (HFP1.5)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile
(AVRCP1.3)
– Object Push Profile (OPP)
– Phonebook Access Profile (PBAP)
– Serial Port Profile (SPP)
Adjust the
microphone angle
Secure using cord clamps (not
supplied) if necessary.
Microphone input jack
Microphone
(supplied)
Rear panel
Ensure that the passkey which appears
on the unit and Bluetooth device is the
same.
Press the volume knob to confirm the
passkey.
Operate the Bluetooth device to confirm
the passkey.
(B) “[Device Name]” “VOL–YES”
“BACK–NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on
the display, enter the PIN code “0000”
into the Bluetooth device.
You can change to a desired PIN code
before pairing.
( 13)
• If only “PAIRING” appears, operate the
Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing
is completed.
• “ ” or “ ” will light up when a Bluetooth
mobile phone is connected.
• “ ” will light up when a Bluetooth audio
player is connected.
Bluetooth compatibility check mode
You can check the connectivity of the
supported profile between the Bluetooth
device and the unit.
• Make sure there is no Bluetooth device
connected.
1 Press and hold .
“BLUETOOTH” “CHECK MODE” appears.
“SEARCH NOW USING PHONE” “PIN IS
0000” scrolls on the display.
JS_JVC_KD_R951BT_E_02_EN.indd 9JS_JVC_KD_R951BT_E_02_EN.indd 9 12/9/2013 4:02:53 PM12/9/2013 4:02:53 PM
Downloaded from www.vandenborre.be

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Bluetooth mobile phone
To Do this
Receive a call Press or the volume knob.
On RM-RK52: Press J/K/ H/I.
• When
[AUTO ANSWER] is set to the selected time, the unit answers
incoming call automatically.
( 11)
Reject an incoming
call
Press and hold or the volume knob.
On RM-RK52: Press and hold J/K/ H/I.
End a call Press and hold or the volume knob.
On RM-RK52: Press and hold J/K/ H/I.
Activate or deactivate
hands-free mode
Press the volume knob during a call.
•
Operations may vary according to the connected Bluetooth mobile
phone.
Adjust the phone
volume
Turn the volume knob during a call.
Phone volume:
[00] to [50] (Default: [15] )
• This adjustment will not affect the volume of the other sources.
Switch between two
connected phones
Press repeatedly.
• Not applicable during a call.
Improve the sound quality during a call
While talking on the phone....
1 Press and hold MENU.
2 Turn the volume knob to make a selection (see the following table), then press the knob.
3 Press MENU to exit.
To return to the previous setting item or hierarchy, press GT/P.
Default:
XX
MIC LEVEL –20 — +08 ( 0 ):The sensitivity of the microphone increases as the number increased.
NOISE RDCT –05 —– 20 ( –10 ):Adjust the noise reduction level until the least noise is being heard during a
phone conversation.
ECHO CANCEL 1 — 10 ( 4 ):Adjust the echo cancellation delay time until the least echo is being heard during a phone
conversation.
BLUETOOTH®
2 Search and select “JVC UNIT” on the Bluetooth
device within 3minutes.
3 Perform (A), (B) or (C) depending on what
appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey):
Ensure that the same passkey appears on
the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on
the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to
confirm pairing.
After pairing is successful, “PAIRING OK” “[Device
Name]” appears and Bluetooth compatibility check
starts.
If “CONNECT NOW USING PHONE” appears, operate
the Bluetooth device to allow phonebook access to
continue.
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*1and/or
“A.STREAM OK”*2and/or “PBAP OK”*3: Compatible
*1Compatible with Hands-Free Profile (HFP)
*2Compatible with Advanced Audio Distribution
Profile (A2DP)
*3Compatible with Phonebook Access profile
(PBAP)
After 30 seconds, “PAIRING DELETED” appears to
indicate that pairing has been deleted, and the unit
exits check mode.
• To cancel, press and hold B/SOURCE to turn off
the power, then turn on the power again.
JS_JVC_KD_R951BT_E_04_EN.indd 10JS_JVC_KD_R951BT_E_04_EN.indd 10 12/11/2013 4:01:48 PM12/11/2013 4:01:48 PM
Downloaded from www.vandenborre.be

11
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
SETTINGS Default: XX
AUTO ANSWER 01 SEC
— 30 SEC :The unit answer incoming call automatically in the
selected time (seconds).;
OFF :Cancels.
RING TONE IN UNIT: The unit rings to notify you when a call/text message comes in.
(Default ring tone is different according to the paired device.)
•
CALL: Selects your preferred ring tone ( TONE 1 — 5 ) for incoming calls.
•
MESSAGE: Selects your preferred ring tone ( TONE 1 — 5 ) for incoming
text messages.
IN PHONE: The unit uses the connected phones’ ring tone to notify you
when a call/text message comes in. (The connected phone will ring if it does
not support this feature.)
RING COLOR
(for KD-R951BT )
COLOR  01 — COLOR  29 ( COLOR 06 ): Display zone will change to the
selected color during a call or when a text message comes in.;
OFF :Cancels.
MSG NOTICE * ON: The unit rings and “RCV MESSAGE” appears to notify you of an incoming
text message.;
OFF :Cancels.
* Functionality depends on the type of the phone used.
Text message notification
When the phone receives a text message, the unit rings and “RCV MESSAGE”
appears.
• You cannot read, edit, or send a message through the unit.
• To clear the message, press any button.
Use Voice Recognition
1 Press and hold .
The connected phone (which has been paired the earliest) is activated.
However, if priority device is connected, pressing and holding
activate the priority device.
( 12, PRIORITY)
2 Speak the name of the contact you want to call or the voice command
to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
•
This unit also supports the intelligent personal assistant function of iPhone.
Bluetooth mode operations
1 Press to enter Bluetooth mode.
2 Turn the volume knob to make a selection (see the following
table), then press the knob.
3 Press MENU to exit.
To return to the previous setting item or hierarchy, press GT/P.
RECENT CALL
1 Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M”
indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call
number.
2 Press the volume knob to call.
PHONEBOOK
1 Turn the volume knob to select a name, then press the knob.
2 Turn the volume knob to select a phone number, then press the
knob to call.
• If the phone supports PBAP, the phonebook of the connected
phone is automatically transferred to the unit when pairing. If the
phone does not support PBAP, “SEND P.BOOK MANUALLY” appears.
Transfer the phonebook manually.
(  13, P.BOOK WAIT)
• This unit can display only non-accent letters. (Accent letters such as
“Ú” is showns as “U”.)
• If the phonebook contains many contacts,
(  12, Select a
contact by name).
DIAL NUMBER
1 Turn the volume knob to select a number (0 to 9) or character ( ,
#, +).
2 Press S/ T to move the entry position.
Repeat steps
1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
VOICE Speak the name of the contact you want to call or the voice command
to control the phone functions.
( Use Voice Recognition)
JS_JVC_KD_R951BT_E_06_EN_f.indd 11JS_JVC_KD_R951BT_E_06_EN_f.indd 11 1/8/2014 2:19:32 PM1/8/2014 2:19:32 PM
Downloaded from www.vandenborre.be

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select a contact by name
• You can search through the contacts quickly according to the first
letter (A to Z, 0 to 9, and OTHERS).
• “OTHERS” appears if the first character is other than A to Z, 0 to 9.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [PHONEBOOK] , then press the
knob.
3 Press 1K/2Jto select the desired letter.
4 Turn the volume knob to select a name, then press the knob.
5 Turn the volume knob to select a phone number, then press the
knob to call.
To return to the previous setting item or hierarchy, press T/P.
Store a contact in memory
You can store up to 6 contacts.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [RECENT CALL] , [PHONEBOOK] , or
[DIAL NUMBER] , then press the knob.
3 Turn the volume knob to select a contact or enter a phone
number.
If a contact is selected, press the volume knob to show the phone
number.
4 Press and hold one of the number buttons (1to 6).
“MEMORY P(selected preset number)” appears when the contact
is stored.
To erase a contact from the preset memory, select [DIAL NUMBER] in
step
2 and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1to 6).
3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
BLUETOOTH®
Delete a contact
Not applicable for mobile phone that supports PBAP.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [RECENT CALL] or [PHONEBOOK] , then press
the knob.
3 Turn the volume knob to select a contact or a phone number.
4 Press and hold T/P.
5 Turn the volume knob to select [DELETE] or [DELETE ALL] , then press the
knob.
DELETE : Selected name or phone number in step 3is deleted.
DELETE ALL : All names or phone numbers from the selected menu in step 2
is deleted.
6 Turn the volume knob to select [YES] or [NO] , then press the knob.
Bluetooth mode settings
1 Press and hold MENU.
2 Turn the volume knob to select [BLUETOOTH] , then press the knob.
3 Turn the volume knob to make a selection (see the following table),
then press the knob.
4 Press MENU to exit.
To return to the previous setting item or hierarchy, press T/P.
Default:
XX
PHONE
Selects the phone or audio device to connect or disconnect.
“” appears in front of the device name.
AUDIO
APPLICATION
Shows the connected phone name using the JVC Smart Music Control * 1
app. “ ” appears in front of the device name.
DELETE PAIR 1 Turn the volume knob to select a device to delete, then press the knob.
2 Turn the volume knob to select [YES] or [NO] , then press the knob.
PRIORITY Selects a device to be connected as priority device. “ ” appears in front of
the device name set as priority.
•
“NO PAIR” appears if there is no registered device found.
JS_JVC_KD_R951BT_E_06_EN.indd 12JS_JVC_KD_R951BT_E_06_EN.indd 12 1/6/2014 12:24:03 PM1/6/2014 12:24:03 PM
Downloaded from www.vandenborre.be

13
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Bluetooth audio player
Operations and display indications may differ
according to their availability on the connected
device.
To Do this
Playback 1 Press B/SOURCE to
select BTAUDIO.
2 Operate the Bluetooth
audio player to start
playback.
Pause or resume
playback Press MENU (or press
on RM-RK52).
Select group or
folder
Press 1K/2J(or press
J/Kon RM-RK52).
Reverse/forward
skip
Press S/T(or press
H/Ion RM-RK52).
Reverse/
fast-forward
Press and hold S/T
(or press and hold H/I
on RM-RK52).
Repeat play Press 4 repeatedly to
make a selection.
TRACKRPT, ALLRPT,
RPTOFF
Random play Press 3 repeatedly to
make a selection.
GROUPRND, ALLRND,
RNDOFF
AUDIO SETTINGS
1 Press and hold MENU.
2 Turn the volume knob to make a selection
(see the following table), then press the
knob.
Repeat step 2until the desired item is
selected.
3 Press MENU to exit.
To return to the previous setting item or
hierarchy, press T/P.
Default:
XX
EQ SETTING
EQ PRESET FLAT
/ HARD ROCK / JAZZ / POP / R&B /
TALK / USER1 / USER2 / VOCAL BOOST /
BASS BOOST / CLASSICAL /
DANCE :Selects a preset equalizer.
EASY EQ
Default: 00
1 USER1 / USER2 :Select a preset name.
2 Adjust your own sound settings.
(For KD-R852BT / KD-R851BT )
SUB.W
*1
: –08 to +08
BASS
 LVL : –06 to +06
MID
 LVL: –06 to +06
TRE
 LVL : –06 to +06
(For KD-R951BT )
SUB.W
*1
: –08 to +08
BASS
 LVL : –10 to +10
MID
 LVL: –10 to +10
TRE
 LVL : –10 to +10
P.BOOK
WAIT
* 2
Copies up to 400 numbers from the
phonebook memory of a connected
phone.
SET PINCODE
(0000)
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a
number.
2 Press S/ T to move the entry
position.
Repeat steps
1 and 2 until you finish
entering the PIN code.
3 Press the volume knob to confirm.
AUTO CNNCT ON :The unit automatically reconnect
when the Bluetooth device is within
range.;
OFF :Cancels.
INITIALIZE YES :Initializes all the Bluetooth settings
(including stored pairing, phonebook,
and etc.).;
NO :Cancels.
INFORMATION MY  BT  NAME : Displays the unit name
(JVCUNIT).;
MY  ADDRESS : Shows
address of this unit.
*1JVC Smart Music Control is designed to view
JVC car receiver status and perform simple
control operations on Android smart phones.
For JVC Smart Music Control operations, visit
JVC website: <http://www.jvc.net/cs/car/>.
*2Selectable only when the connected phone
supports OPP.
JS_JVC_KD_R951BT_E_06_EN.indd 13JS_JVC_KD_R951BT_E_06_EN.indd 13 1/6/2014 12:24:07 PM1/6/2014 12:24:07 PM
Downloaded from www.vandenborre.be

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
PRO EQ
(for
KD-R852BT /
KD-R851BT )
1 USER1 / USER2 :Select a preset name.
2 BASS / MIDDLE / TREBLE :Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
BASS Frequency: 60 / 80 / 100 / 200 Hz Default: ( 80 Hz )
Level:
–06 to +06 ( 00 )
Q:
Q1.0 / Q1.25 / Q1.5 / Q2.0 ( Q1.0 )
MIDDLE Frequency: 0.5 / 1.0 / 1.5 / 2.5 kHz Default: ( 1.0 kHz )
Level:
–06 to +06 ( 00 )
Q:
Q0.75 / Q1.0 / Q1.25 ( Q1.25 )
TREBLE Frequency: 10.0 / 12.5 / 15.0 / 17.5 kHz Default: ( 10.0 kHz )
Level:
–06 to +06 ( 00 )
Q:
Q FIX ( Q FIX )
PRO EQ
(for
KD-R951BT )
1 USER1 / USER2 :Select a preset name.
2 BASS / MID BASS / MID / MID HIGH / HIGH :Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
BASS Frequency: 63 / 80 / 100 / 125 Hz Default:( 80 Hz )
Level:
–10 to +10 ( 00 )
Q:
Q1.0 / Q1.25 / Q1.5 / Q2.0 ( Q1.25 )
MID BASS Frequency: 200 / 250 / 315 / 400 Hz Default:( 250 Hz )
Level:
–10 to +10 ( 00 )
Q:
Q1.0 / Q1.25 / Q1.5 / Q2.0 ( Q1.25 )
MID Frequency: 630 / 800 Hz / 1.0 / 1.25 kHz Default:( 800 Hz )
Level:
–10 to +10 ( 00 )
Q:
Q0.75 / Q1.0 / Q1.25 / Q2.0 ( Q1.0 )
MID HIGH Frequency: 2.0 / 2.5 / 3.15 / 4.0 kHz Default:( 2.5 kHz )
Level:
–10 to +10 ( 00 )
Q:
Q0.75 / Q1.0 / Q1.25 / Q2.0 ( Q1.0 )
HIGH Frequency: 6.3 / 8.0 / 10.0 / 12.5 kHz Default:( 8.0 kHz )
Level:
–10 to +10 ( 00 )
Q:
Q0.75 / Q1.0 / Q1.25 / Q2.0 ( Q1.0 )
AUDIO
BASS BOOST +01
/ +02 : Selects your preferred bass boost level.; OFF :Cancels.
LOUD 01 / 02 :Boosts low or high frequencies to produce a well-balanced sound at
low volume.;
OFF :Cancels.
AUDIO SETTINGS
SUB.W LEVEL
*1
–08 — +08 ( 00 ):Adjusts the subwoofer output level.
SUB.W
*2
ON / OFF : Turns on or off the subwoofer output.
SUB.W  LPF
*1
THROUGH :All signals are sent to the subwoofer. ; LOW  55Hz /
MID  85Hz / HIGH 120Hz :Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
HPF *3 OFF :All signals are sent to the front/rear speakers.; LOW  100Hz /
MID  120Hz / HIGH 150Hz :Audio signals with frequencies lower than
100Hz/ 120Hz/ 150Hz are cut off from the front/rear speakers.
FADER
*4*5
R06 — F06 ( 00 ):Adjusts the front and rear speaker output balance.
BALANCE
*4
L06 — R06 ( 00 ):Adjusts the left and right speaker output balance.
VOL ADJUST –05 — +05 ( 00 ):Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP GAIN LOW  POWER :Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGH POWER :The maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF :Cancels.
L/O MODE
*6
SUB.W / REAR :Selects whether rear speakers or a subwoofer are
connected to the REAR/SW line out terminals on the rear panel (through an
external amplifier).
*1For
KD-R852BT / KD-R851BT : Displayed only when [L/O  MODE] is set to
[SUB.W] and [SUB.W] is set to [ON] .
*2For
KD-R852BT / KD-R851BT : Displayed only when [L/O MODE] is set to
[SUB.W] .
*3For
KD-R951BT .
*4This adjustment will not affect the subwoofer output.
*5If you are using a two-speaker system, set the fader level to
[00] .
*6For
KD-R852BT / KD-R851BT .
JS_JVC_KD_R951BT_E_02_EN.indd 14JS_JVC_KD_R951BT_E_02_EN.indd 14 12/3/2013 12:11:30 PM12/3/2013 12:11:30 PM
Downloaded from www.vandenborre.be

15
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DISPLAY SETTINGS
KD-R852BT / KD-R851BTKD-R951BT
1 Press and hold MENU.
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
Repeat step
2until the desired item is selected.
3 Press MENU to exit.
To return to the previous setting item or hierarchy, press GT/P.
Default: XX
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the [BRIGHTNESS]
setting.
AUTO :Changes between the day and night adjustments when you turn off or
on the car headlights.*
1
; ON :Selects the night adjustments.; OFF :Selects the
day adjustments.
BRIGHTNESS Sets the button, display and USB input terminal brightness for day and night
separately.
1 DAY / NIGHT :Select day or night.
2 Select a zone for setting. ( Illustration above)
3 Set the brightness level ( 00 to 31 ).
(Default:
KD-R951BT : DAY : 31 ; NIGHT : 11
KD-R852BT / KD-R851BT : BUTTON ZONE : DAY : 25 ; NIGHT : 09
DISP ZONE : DAY : 31 ; NIGHT : 12 )
SCROLL * 2 ONCE :Scrolls the display information once.; AUTO :Repeats scrolling at
5-second intervals.;
OFF :Cancels.
*1
The illumination control wire connection is required. ( 21)
*2
Some characters or symbols will not be shown correctly (or will be blanked).
Default: XX
COLOR (for KD-R951BT )
PRESET You can select a color for [ ALL ZONE ], [ ZONE 1 ], [ DISP ZONE ], or
[
ZONE 2 ] separately. For [ ALL ZONE ], you can also select a color pattern.
Default color:
ALL ZONE : [ COLOR 06 ], ZONE 1 : [ COLOR 06 ],
DISP ZONE : [ COLOR 01 ], ZONE 2 : [ COLOR 27 ]
1 Select a zone for setting. ( Illustration on left column)
2 Select a color for the selected zone.
•
COLOR 01 to COLOR 29
• USER : The color you have created for [ DAY COLOR ] or
[
NIGHT COLOR ] is shown.
•
COLOR FLOW 01 to COLOR FLOW 03 : Color changes at different
speeds.
•
SPECTRUM / GROOVE / TECHNO / EMOTION / RELAX /
NIGHT SWEEP : The selected color pattern is shown.* (Selectable
only when [
ALL ZONE ] is selected in step 1 .)
* If one of these color pattern is selected, the [
ZONE 1 ], [ DISP ZONE ],
[
ZONE 2 ] illumination color will change to the default color.
DAY COLOR Store your own day and night colors for different zone.
1 Select a zone for setting. ( Illustration on left column)
2 RED / GREEN / BLUE :Select a primary color.
3 00 to 31 :Select the level.
Repeat steps
2 and 3 for all the primary colors.
• Your setting is stored to
[USER] in [PRESET] .
• If
[00] is selected for all primary colors for [DISP ZONE] , nothing
appears on the display.
NIGHT COLOR
COLOR GUIDE ON
:Changes the button, display and USB input terminal illumination
when settings are performed on menu and list search. Display zone will
automatically change depending on volume level.;
OFF :Cancels.
[NIGHT COLOR] or [DAY COLOR] is changed by turning on or off your car’s
headlight.
JS_JVC_KD_R951BT_E_02_EN.indd 15JS_JVC_KD_R951BT_E_02_EN.indd 15 12/9/2013 4:03:01 PM12/9/2013 4:03:01 PM
Downloaded from www.vandenborre.be

16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
About discs and audio files
• This unit can only play the following CDs:
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped during playback.
•
Unplayable discs:
- Discs that are not round.
- Discs with coloring on the recording surface or discs that
are dirty.
- Recordable/ReWritable discs that have not been
finalized.
- 8 cm CD. Attempting to insert using an adapter may
cause malfunction.
•
DualDisc playback: The Non-DVD side of a “DualDisc”
does not comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD side of a DualDisc
on this product cannot be recommended.
•
Playable files:
- File extensions: MP3(.mp3), WMA(.wma)
- Bit rate: MP3: 8kbps — 320kbps
WMA: 32kbps — 192kbps
- Sampling frequency:
MP3: 48kHz, 44.1kHz, 32kHz, 24kHz, 22.05kHz,
16kHz, 12kHz, 11.025kHz, 8kHz
WMA: 8kHz — 48kHz
- Variable bit rate (VBR) files.
•
Maximum number of characters for file/folder name:
It depends on the disc format used (includes 4 extension
characters—<.mp3> or <.wma>).
- ISO 9660 Level 1 and 2: 32 characters
- Romeo: 32 characters
- Joliet: 32 characters
- Windows long file name: 32 characters
MORE INFORMATION
About USB devices
• This unit can play MP3/WMA/WAV files stored on a USB
mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5m
may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- WAV Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders
(999 files per folder including folder without unsupported
files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is
other than 5V and exceeds 1A.
About iPod/iPhone
• Made for
- iPod touch (1st, 2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th and 7th generation)
- iPhone, iPhone 3G, 3GS, 4, 4S, 5
• It is not possible to browse video files on the “Videos” menu
in
[HEAD MODE] .
• The song order displayed on the selection menu of this unit
may differ from that of the iPod/iPhone.
• If some operations are not performed correctly or as
intended, visit: <http://www.jvc.net/cs/car/>.
About Bluetooth
• Depending on the Bluetooth version of the device, some
Bluetooth devices may not be able to connect to this unit.
• This unit may not work with some Bluetooth devices.
Signal conditions vary, depending on the surroundings.
• For more information about Bluetooth, visit the following
JVC website: <http://www.jvc.net/cs/car/>.
About JVC Playlist Creator and JVC Music
Control
• This unit supports the PC application JVC Playlist Creator
and Android
TM
application JVC Music Control.
• When you play audio file with song data added using the
JVC Playlist Creator or JVC Music Control, you can search for
audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available
from the following web site:
<http://www.jvc.net/cs/car/>.
Available Cyrillic letters
Available characters
Display indications
JS_JVC_KD_R951BT_E_02_EN.indd 16JS_JVC_KD_R951BT_E_02_EN.indd 16 12/3/2013 12:11:30 PM12/3/2013 12:11:30 PM
Downloaded from www.vandenborre.be

17
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Change the display information
Press DISP repeatedly.
FM or AM Station name (PS)*
1
Frequency Program type (PTY)*
1
*
2
Title*
1
*
2
Day/Clock (back to the beginning)
*1
For FM Radio Data System stations only.
*2
If unavailable, “NO PTY” / “NO TEXT” appears.
CD or USB Playing time Day/Clock Disc name*
3
Album title/Artist*
4
Track
title*
5
Folder/file name*
6
(back to the beginning)
*3
Only for CD-DA: If not recorded, “NO NAME” appears.
*4
Only for MP3/WMA/WAV files: If not recorded, “NO NAME” appears.
*5
If not recorded, “NO NAME” appears.
*6
Only for MP3/WMA/WAV files.
USB-IPOD Playing time Day/Clock Album title/Artist*
7
Track title*
7
(back to
the beginning)
*7
If not recorded, “NO NAME” appears.
AUX AUX Day/Clock
BT AUDIO Playing time Day/Clock Album title/Artist*
8
Track title*
8
(back to
the beginning)
*8
If not recorded, “NO NAME” appears.
MORE INFORMATION
Symptom Remedy
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHK WIRING
THEN RESET UNIT” /
“WARNING CHK WIRING THEN
RESET UNIT” appears and no
operations can be done.
Check to be sure the terminals of the speaker wires are
insulated properly, then reset the unit. If this does not
solve the problem, consult your nearest service center.
Source cannot be selected. Check the
[SRC SELECT] setting. ( 4)
Radio reception is poor. /
Static noise while listening to
the radio.
• Connect the antenna firmly.
• Pull the antenna out all the way.
Correct characters are not
displayed.
This unit can only display uppercase letters, numbers, and
a limited number of symbols. The unit can also display
uppercase Cyrillic letters.
( 16)
“PLEASE” and “EJECT” appear
alternately.
Press , then insert the disc correctly.
“IN DISC” appears. Make sure nothing is blocking the loading slot when you
eject the disc.
Disc cannot be ejected. Press and hold to forcibly eject the disc. Be careful not
to drop the disc when it is ejected.
Playback order is not as
intended.
The playback order is determined by the file name (USB) or
the order in which files were recorded (disc).
Elapsed playing time is not
correct.
This depends on the recording process earlier.
“NOT SUPPORT” appears and
track skips.
Check whether the track is a playable format.
( 16)
TROUBLESHOOTING
JS_JVC_KD_R951BT_E_02_EN.indd 17JS_JVC_KD_R951BT_E_02_EN.indd 17 12/3/2013 12:11:30 PM12/3/2013 12:11:30 PM
Downloaded from www.vandenborre.be

18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy
“CANNOT PLAY” flashes and/
or connected device cannot
be detected.
• Check whether the connected device is compatible with this
unit and ensure the files are in supported formats.
( 16)
• Reattach the device.
“READING” keeps flashing. • Do not use too many hierarchical levels and folders.
• Reload the disc or reattach the USB device.
The iPod/iPhone does not
turn on or does not work.
• Check the connection between this unit and iPod/iPhone.
• Detach and reset the iPod/iPhone using hard reset.
Bluetooth®
No Bluetooth device
is detected.
• Search from the Bluetooth device again.
• Reset the unit.
( 3)
Pairing cannot be
made.
• Make sure you have entered the same PIN code to both the
unit and Bluetooth device.
• Delete pairing information from both the unit and the
Bluetooth device, then perform pairing again.
( 9)
“PAIRING FULL”
appears.
The number of registered devices has reached its limit. Retry
after deleting an unnecessary device.
( 12, DELETE PAIR)
“PLEASE WAIT”
appears.
The unit is preparing to use the Bluetooth function. If the
message does not disappear, turn off and turn on the unit,
then connect the device again.
“BT DEVICE NOT
FOUND” appears.
The unit failed to search for the registered Bluetooth devices
during
[AUTO CNNCT] . Turn on Bluetooth from your device
and connect manually.
( 13)
Echo or noise occurs. • Adjust the microphone unit’s position. ( 9)
• Check the [ECHO CANCEL] setting. ( 10)
Phone sound quality
is poor.
• Reduce the distance between the unit and the Bluetooth
device.
• Move the car to a place where you can get a better signal
reception.
Symptom Remedy
Bluetooth®
“NOT SUPPORT” appears. The connected phone does not support Voice
Recognition feature.
“ERROR” appears. Try the operation again. If “ERROR” appears again,
check if the device supports the function you have
tried.
The unit does not respond
when you try to copy the
phonebook to the unit.
You may have tried to copy the same entries (as
stored) to the unit. Press
DISP or GT/P to exit.
Sound is being interrupted or
skipped during playback of a
Bluetooth audio player.
• Reduce the distance between the unit and the
Bluetooth audio player.
• Turn off, then turn on the unit and try to connect
again.
• Other Bluetooth devices might be trying to connect
to the unit.
The connected Bluetooth
audio player cannot be
controlled.
• Check whether the connected Bluetooth audio
player supports Audio/Video Remote Control Profile
(AVRCP). (Refer to the instructions of your audio
player.)
• Disconnect and connect the Bluetooth player again.
“H/W ERROR” appears. Reset the unit and try the operation again. If “H/W
ERROR” appears again, consult your nearest service
center.
“BT ERROR PLS UPDATE”
appears.
Update the Bluetooth firmware.
( 4)
If you still have troubles, reset the unit. ( 3)
JS_JVC_KD_R951BT_E_02_EN.indd 18JS_JVC_KD_R951BT_E_02_EN.indd 18 12/9/2013 4:11:40 PM12/9/2013 4:11:40 PM
Downloaded from www.vandenborre.be