JVC SA-DV60E User manual

LLT0012
SA-DV60U
This instruction manual has been
manufactured from 100% recycled paper.
INSTRUCTIONS
DV INTERFACE BOARD
For Customer Use:
Enter below the Serial No. on the
board in the space below. Retain this
information for future reference.
Model No. SA-DV60U
Serial No.
DV IN/OUT
VCR CONTROL
This section of instruction manual is specially edited for service
purpose with modified contents.
It is not recommended to use, this section for the substitution of
the original book in the merchandise.
CAUTION
Some of the pages are common to both U and E models,
and some are located on the right section.
Follow the pages indicated (U-**) when reading through.
NOTE
CONTROLS, CONNECTORS
AND INDICATORS
SYSTEM CONFIGURATION,
CONNECTIONS
INSTALLATION SPECIFICATIONS
SWITCH THE SETTINGS
OF THE D9 DEVICE
PRECAUTIONS FOR USE
OF DV INPUT/OUTPUT
LLT0013
SA-DV60E
This instruction manual has been manufactured from 100% recycled paper.
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
DV INTERFACE BOARD
DV IN/OUT
VCR CONTROL
This section of instruction manual is specially edited for service
purpose with modified contents.
It is not recommended to use, this section for the substitution of
the original book in the merchandise.
Some of the pages are common to both U and E models,
and some are located on the left section.
Follow the pages indicated (E-**) when reading through.
CAUTION
NOTE
CONTROLS, CONNECTORS
AND INDICATORS
SYSTEM CONFIGURATION,
CONNECTIONS
INSTALLATION SPECIFICATIONS
SWITCH THE SETTINGS
OF THE D9 DEVICE
PRECAUTIONS FOR USE
OF DV INPUT/OUTPUT
E
U
All manuals and user guides at all-guides.com
all-guides.com

(E-2)
Port
DV IN/OUT
VCR CONTROL
Cable
Shielded Twist Pair Cable
Twist Pair Cable
Length
4.5 meters
5 meters
Supplement (SA-DV60E)
This equipment is in conformity with the provisions and protection requirements of the correspond-
ing European Directives, This equipment is designed for professional video appliances and can
be used in the following environments:
• Controlled EMC environment (for example purpose built broadcasting or recording studio), and
the rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)
In order to keep the best performance and furthermore for electromagnetic compatibility we
recommend to use cables not exceeding the following length:
— MEMO —
All manuals and user guides at all-guides.com

(U-2)
This unit is a DV interface board designed to be installed in the BR-D80U, BR-D85U or BR-
D750U video cassette recorder models or in the BR-D50U, BR-D350U or BR-D51U video
cassette player models to enable the input and output (only output in the case of the player) of
DV signals.
Thank you for purchasing the JVC SA-DV60U DV Interface Board.
SA-DV60U
DV CAMCORDER
DV RECORDER
NONLINEAR EDITOR
DV INTERFACE BOARD
Connection with D-9 recorder
Connection with D-9 player
D-9
IEEE1394
DV(25 Mbps) D-9(50 Mbps)
1
DV D9 .......................................... Linear editing system
2
D9 DV nonlinear editing system... Capture, writing back
3
DV D9 .......................................... Dubbing system
Applications:
This unit makes possible the following digital editing/dubbing operations.
Image of DV D-9 Interface
CAUTION
With the D9 devices carrying the following or previous serial numbers, a malfunction
described below is observed when each device is connected to a nonlinear editor.
•With certain nonlinear editors, the time code at the edit-out point may be disturbed as
a result of writing back from the nonlinear editor to the D9 device.
BR-D85U: No. xxxx0508 or before
BR-D80U: No. xxxx0466 or before
(E-3)
This unit is a DV interface board designed to be installed in the BR-D80E, BR-D85E, BR-D85EC
or BR-D750E video cassette recorder models or in the BR-D50E, BR-D50EC, BR-D350E or BR-
D51E video cassette player models to enable the input and output (only output in the case of the
player) of DV signals.
Thank you for purchasing the JVC SA-DV60E DV Interface Board.
SA-DV60E
DV CAMCORDER
DV RECORDER
NONLINEAR EDITOR
DV INTERFACE BOARD
Connection with D-9 recorder
Connection with D-9 player
D-9
IEEE1394
DV(25 Mbps) D-9(50 Mbps)
1DV D9 .......................................... Linear editing system
2D9 DV nonlinear editing system... Capture, writing back
3DV D9 .......................................... Dubbing system
Applications: This unit makes possible the following digital editing/dubbing operations.
Image of DV D-9 Interface
CAUTION
With the D9 devices carrying the following or previous serial numbers, a malfunction
described below is observed when each device is connected to a nonlinear editor.
•With certain nonlinear editors, the time code at the edit-out point may be disturbed as
a result of writing back from the nonlinear editor to the D9 device.
BR-D85E: No. xxxx0673 or before
BR-D85EC: No. xxxx0370 or before
BR-D80E: No. xxxx0362 or before
E
U
All manuals and user guides at all-guides.com

(U-3)
Components
This unit is composed of a circuit board and connector panel.
Circuit board .............. x 1
Connector panel ........ x 1 (with connection wires)
1
[CN302] Connect to the 7-pin plug of the connector
panel.
2
[CN202] Connect to the 6-pin plug of the connector
panel.
3
Ejector Used to eject the board.
Push this part in when inserting the board.
Circuit Board
(DV I/O Board)
Connector Panel
1. Controls, Connectors and Indicators
123
3
DV I/O
DV IN/OUT
VCR CONTROL
1
2
6-pin plug
7-pin plug
1
DV IN/OUT connector
Input and output of IEEE1394 standard digital signals.
In addition to the digital video and digital audio signals,
this connector can also be used to exchange timecode
signals and control signal input from a DV (i.Link)-
compatible PC.
2
VCR CONTROL (RS-422 interface) connector
Connect to the REMOTE (9-pin) connector on the D9
main body in order to exchange commands between
the D9 and DV devices through the DV I/O board.
During playback of a D9 device, this connector sends
the timecode signal of the D9 device to the DV device
through the DV I/O board.
Accessories
1. RS-422 cable ..... x 1 (Both millimeter screws and inch screws are provided in the package.)
2. Ferrite core ......... x 1 (To be attached when using headphones)
☞
See page 8
(E-10)
(E-4)
(E-5)
2. System Configuration, Connections
System Configuration and Connection Examples for different Applications
A system for digital editing and/or dubbing can be configured and connected by referring to the
following examples according to the available units and the required function.
䡵Operate the connected units correctly by referring to their instruction manuals.
䡵Cables for connection between units are not provided.
Please purchase the applicable connector cables as required.
䡵DV connection target models
GY-DV500E *
1,
*
3
GY-DV550E
GY-DV700WE *
1
BR-DV600E *
3
BR-DV600EA
DV nonlinear editor *
2
*1. The GY-DV500E and GY-DV700WE models are not capable of DV input recording through
the DV input. Refer to their instruction manuals for details.
*2. For the DV nonlinear editors, please consult your nearest JVC dealer.
*3. Precautions for connection of the GY-DV500E or BR-DV600E
(1) Time codes cannot be dubbed.
(2) When the DV device is switched from the Still mode to the Play mode, audio may be
interrupted momentarily. This is not a malfunction.
(3) Sets having serial numbers other than those shown below cannot be connected to this
unit. For information concerning their upgrade versions, please consult your local JVC-
authorized service agent.
Model Name Last 5 digits of S/No.
GY-DV500E xxx14590 and after
xxx54590 and after
xxx30401 and after
GY-DV500EC xxx10281 and after
xxx50281 and after
Model Name Last 5 digits of S/No.
GY-DV500ECK xxx30251 and after
BR-DV600E xxx11535 and after
xxx51535 and after
BR-DV600EC xxx10001 and after
xxx50001 and after
E
All manuals and user guides at all-guides.com

(U-4)
2. System Configuration, Connections
System Configuration and Connection Examples for different Applications
A system for digital editing and/or dubbing can be configured and connected by referring to the
following examples according to the available units and the required function.
䡵Operate the connected units correctly by referring to their instruction manuals.
䡵Cables for connection between units are not provided.
Please purchase the applicable connector cables as required.
䡵DV connection target models
GY-DV500U *
2
GY-DV550U
GY-DV700WU BR-DV600U *
2
BR-DV600UA DV nonlinear editor *
1
*1. For the DV nonlinear editors, please consult your nearest JVC dealer.
*2. Precautions for connection of the GY-DV500U or BR-DV600U
(1) Time codes cannot be dubbed.
(2) When the DV device is switched from the Still mode to the Play mode, audio may be
interrupted momentarily. This is not a malfunction.
(3) Sets having serial numbers other than those shown below cannot be connected to this
unit. For information concerning their upgrade versions, please consult your local JVC-
authorized service agent.
AC IN 120V 50/60Hz
VIDEOOUT
REF
VIDEOIN
YLINE
R-Y
B-YY/C358
Y
R-Y
B-YY/C358
LINE-2
LINE-1
VIDEO AUDIO
MONITOROUT
TIMECODE
ON
OFF 75Ω
DIAGNOSTIC
REMOTE(9P)
VIDEOCONTROL
AUD-1
AUD-2
AUD-1
AUD-2
AUDIOIN AUDIO OUT
LEVEL
-6dB +4dB
LEVEL
-6dB +4dB
IN OUT
DVIN/OUT
VTRCTRL
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSONSCREEN
TIMECODESYSTEM
STANDBY
TIMECODEVIDEOCONTROL
MENU SET SELECTMETERMODE
FINE TRACKING TIMECODEGEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTOOFF
DFEMP JOG
GEN
VIDEOCASSETTE RECORDER
BR-D80U
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
P.READ
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
STATUSSHUTTER
MENU
FILTER
1 3200k
2 5600k
3 5600k+ND
POWER
NG
GAIN OUTPUT WHT.BAL
VTR
ON OFF
ALARM
MONITOR
SAVESTBY
HML
BARSCAM
AUTOKNEE
PRSTAB
ON
OFF
CH-1 CH-2
AUDIO
LEVEL
AUTOIRIS LOLUX
BACKL
NORMAL
SPOTL
STRETCH
NORMAL
COMPRESS
FULLAUTOBLACK
V.IN/A.MONI A.OUT COUNTER
DV CTL
TC
UB
CH-1/2
CH-3/4
Y/C
(CPN)
LINE
L
R
MIX
MIX
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET
SELECT
SHIFT
MENU
HOLD SHIFT A. DUB
ADVANCE PRESET
REW STOP FF
REC PLAY
PAUSE
ON/OFF
MENU
OVER
OVER
HMSF
AUDLOCK
SP
32k 48k
SLAVE PB NDF
SERVO RF
DEW
AUTOOFF
HOLD
CH2/4
CH1/3
VIDEO CASSETTE RECORDER BR-DV600UA
dB
4030 20 10 0
LAP IN OUT SERVO LAP IN OUT SERVO
LAP RESET LAPRESET TOTAL
RECORDER
EJECT
PLAYER
EJECT
P
AUX
CONTINUE START END V.SPEED EVENT
RENUMBER
RIPPLE
MAN.TAKE
LEARN
MENU
REC REW FF STOP
STBOFF
SEARCH PAUSE
/STILL
PLAY
REC REW FF STOP
STBOFF
SEARCHPAUSE
/STILL
PLAY
ASSEM VIDEO AUD-1 AUD-2
SPLIT
TC
SPLIT CANCEL LAST
ED
REC
EE
OUT
IN
OUT
IN ENTRY
PREVIEW AUTOEDIT GOTOREVIEW
SHIFT ALLSTOP
MAX
MIN
MONITOR
MAX
MIN
MONITOR
FWD
REV
STILL
X-1 X1
FWD
REV
STILL
X-1 X1
RECORDER
PLAYER
HOUR MIN SEC FRAME HOUR MIN SEC FRAME
PR
VITC
LTC
CTL
VITC
LTC
CTL
BUMP
PREROLL
7
5
3
ON
OFF
EVENTNo.
V.SPEED
A.SPLIT
DURATION
IN
OUT
IN
OUT
EDITING CONTROL UNIT
RM—G820U
+–
Mini DV
(VIDEO/AUDIO)
DV cable (4P-4P)
Mini DV
tape
DV recorder
BR-DV600UA
Player
Editing control unit RM-G820U
D9 editing recorder BR-D80U
DV camcorder GY-DV500U
Front panel
Rear panel
DV connector DV connector
SA-DV60U
VCR CONTROL
not connected
REMOTE(9P)
REMOTE(9P)
VIDEO OUT
SYNC
IN
9P-9P remote cable
9P-9P remote cable
Recorder
•For data bump, select the recorder
device and use its Learning function.
•The pre-roll time should be set to
more than 5 seconds.
Model Name Last 5 digits of S/No.
GY-DV500U xxx16552 and after
xxx56552 and after
xxx31501 and after
Model Name Last 5 digits of S/No.
BR-DV600U xxx12040 and after
xxx52040 and after
(1) DV D9 linear editing system
The editing precision of the player device of the system described below is +1( ) frame.
+1
–0
(E-6)
AC IN 120V 50/ 60Hz
VIDEOOUT
REF
VIDEOIN
YLINE
R-Y
B-YY/C358
Y
R-Y
B-YY/C358
LINE-2
LINE-1
VIDEO AUDIO
MONITOROUT
TIMECODE
ON
OFF 75Ω
DIAGNOSTIC
REMOTE(9P)
VIDEOCONTROL
AUD-1
AUD-2
AUD-1
AUD-2
AUDIOIN AUDIO OUT
LEVEL
-6dB +4dB
LEVEL
-6dB +4dB
IN OUT
DVIN/OUT
VTRCTRL
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1 TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSONSCREENTIMECODESYSTEM
STANDBY
TIMECODEVIDEOCONTROL
MENU SET SELECTMETERMODE
FINE TRACKING TIME CODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEOCASSETTE RECORDER
BR-D80U
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKING
DA1
P.READ
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
STATUSSHUTTER
MENU
FILTER
1 3200k
2 5600k
3 5600k+ND
POWER
NG
GAINOUTPUTWHT.BAL
VTR
ON OFF
ALARM
MONITOR
SAVESTBY
HML
BARSCAM
AUTOKNEE
PRSTAB
ON
OFF
CH-1 CH-2
AUDIO
LEVEL
AUTOIRIS LOLUX
BACKL
NORMAL
SPOTL
STRETCH
NORMAL
COMPRESS
FULLAUTOBLACK
V.IN/A.MONI A.OUT COUNTER
DV CTL
TC
UB
CH-1/2
CH-3/4
Y/C
(CPN)
LINE
L
R
MIX
MIX
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET
SELECT
SHIFT
MENU
HOLD SHIFT A. DUB
ADVANCE PRESET
REW STOP FF
REC PLAY
PAUSE
ON/OFF
MENU
OVER
OVER
HMSF
AUDLOCK
SP
32k 48k
SLAVE PB NDF
SERVO RF
DEW
AUTO OFF
HOLD
CH 2/4
CH 1/3
VIDEO CASSETTE RECORDER BR-DV600UA
dB4030 20 10 0
LAP IN OUT SERVO LAP IN OUT SERVO
LAP RESET LAP RESET TOTAL
RECORDER
EJECT
PLAYER
EJECT
P
AUX
CONTINUE START END V.SPEED EVENT
RENUMBER
RIPPLE
MAN.TAKELEARN
MENU
REC REW FF STOP
STBOFF
SEARCHPAUSE
/STILL
PLAY
REC REW FF STOP
STBOFF
SEARCHPAUSE
/STILL
PLAY
ASSEM VIDEO AUD-1 AUD-2
SPLIT
TC
SPLIT CANCEL LAST
ED
REC
EE
OUT
IN
OUT
IN ENTRY
PREVIEW AUTOEDIT GOTO REVIEW
SHIFT ALLSTOP
MAX
MIN
MONITOR
MAX
MIN
MONITOR
FWD
REV
STILL
X-1 X1
FWD
REV
STILL
X-1 X1
RECORDER
PLAYER
HOUR MIN SEC FRAME HOUR MIN SEC FRAME
PR
VITC
LTC
CTL
VITC
LTC
CTL
BUMP
PREROLL
7
5
3
ON
OFF
EVENTNo.
V.SPEED
A.SPLIT
DURATION
IN
OUT
IN
OUT
EDITING CONTROL UNIT
RM—G820U
+–
Mini DV
(VIDEO/AUDIO)
DV cable (4P-4P)
Mini DV
tape
DV recorder
BR-DV600EA
Player
Editing control unit RM-G820E
D9 editing recorder BR-D80E
DV camcorder GY-DV500E
(1) DV D9 linear editing system
Front panel
Rear panel
DV connector DV connector
SA-DV60E
VCR CONTROL
not connected
REMOTE(9P)
REMOTE(9P)
VIDEO OUT
SYNC
IN
9P-9P remote cable
9P-9P remote cable
Recorder
•For data bump, select the recorder
device and use its Learning function.
•The pre-roll time should be set to
more than 5 seconds.
The editing precision of the player device of the system described below is +1 frame.
+1
–0
( )
2. System Configuration, Connections (continued)
E
U
All manuals and user guides at all-guides.com

(U-5)
2. System Configuration, Connections (continued)
AC IN 120V 50/ 60Hz
VIDEOOUT
REF
VIDEOIN
YLINE
R-Y
B-YY/C358
Y
R-Y
B-YY/C358
LINE-2
LINE-1
VIDEO AUDIO
MONITOROUT
TIMECODE
ON
OFF 75Ω
DIAGNOSTIC
REMOTE(9P)
VIDEOCONTROL
AUD-1
AUD-2
AUD-1
AUD-2
AUDIOIN AUDIO OUT
LEVEL
-6dB +4dB
LEVEL
-6dB +4dB
IN OUT
DVIN/OUT
VTRCTRL
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSONSCREENTIMECODESYSTEM
STANDBY
TIMECODEVIDEOCONTROL
MENU SET SELECTMETER MODE
FINE TRACKING TIME CODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEOCASSETTE RECORDER
BR-D80U
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
P.READ
D9 editing recorder BR-D80U
Front panel
Rear panel
DV connector
SA-DV60U
REMOTE(9P) VCR CONTROL
DV cables (4P-4P, 6P-4P)
9P-9P remote cable
Capturing
Writing back
(VIDEO/AUDIO)
Nonlinear editor
(2) D9 DV nonlinear editing system
Note on the screws
Both millimeter screws and inch screws are
provided in the package. Connect the cable
by attaching the inch screws as described in
the attached document.
Rear panel:
Inch screws Connector panel: Inch screws
AC IN 120V 50/ 60Hz
VIDEOOUT
REF
VIDEOIN
YLINE
R-Y
B-YY/C358
Y
R-Y
B-YY/C358
LINE-2
LINE-1
VIDEO AUDIO
MONITOROUT
TIMECODE
ON
OFF 75Ω
DIAGNOSTIC
REMOTE(9P)
VIDEOCONTROL
AUD-1
AUD-2
AUD-1
AUD-2
AUDIOIN AUDIO OUT
LEVEL
-6dB +4dB
LEVEL
-6dB +4dB
IN OUT
DVIN/OUT
VTRCTRL
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2
DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSONSCREENTIMECODESYSTEM
STANDBY
TIMECODEVIDEOCONTROL
MENU SET SELECTMETER MODE
FINE TRACKING TIME CODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEOCASSETTE RECORDER
BR-D80U
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
P.READ
D9 editing recorder BR-D80U
Front panel
Rear panel
DV connector
SA-DV60U
REMOTE(9P) VCR CONTROL
DV cable (4P-4P)
9P-9P remote cable
(VIDEO/AUDIO)
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
STATUSSHUTTER
MENU
FILTER
1 3200k
2 5600k
3 5600k+ND
POWER
NG
GAINOUTPUTWHT.BAL
VTR
ON OFF
ALARM
MONITOR
SAVESTBY
HML
BARSCAM
AUTOKNEE
PRSTAB
ON
OFF
CH-1 CH-2
AUDIO
LEVEL
AUTOIRIS LOLUX
BACKL
NORMAL
SPOTL
STRETCH
NORMAL
COMPRESS
FULLAUTOBLACK
DV camcorder GY-DV500U
V.IN/A.MONI A.OUT COUNTER
DV CTL
TC
UB
CH-1/2
CH-3/4
Y/C
(CPN)
LINE
L
R
MIX
MIX
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET
SELECT
SHIFT
MENU
HOLD SHIFT A. DUB
ADVANCE PRESET
REW STOP FF
REC PLAY
PAUSE
ON/OFF
MENU
OVER
OVER
HMSF
AUDLOCK
SP
32k 48k
SLAVE PB NDF
SERVO RF
DEW
AUTO OFF
HOLD
CH 2/4
CH 1/3
VIDEO CASSETTE RECORDER BR-DV600UA
dB4030 20 10 0
DV recorder BR-DV600UA
DV connector
DV connector
(3) DV D9 dubbing system
Connect either one
of the DV recorder
or the Camcorder to
the interface board
(E-7)
2. System Configuration, Connections (continued)
AC IN 120V 50/ 60Hz
VIDEOOUT
REF
VIDEOIN
YLINE
R-Y
B-YY/C358
Y
R-Y
B-YY/C358
LINE-2
LINE-1
VIDEO AUDIO
MONITOROUT
TIMECODE
ON
OFF 75Ω
DIAGNOSTIC
REMOTE(9P)
VIDEOCONTROL
AUD-1
AUD-2
AUD-1
AUD-2
AUDIOIN AUDIO OUT
LEVEL
-6dB +4dB
LEVEL
-6dB +4dB
IN OUT
DVIN/OUT
VTRCTRL
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSONSCREENTIMECODESYSTEM
STANDBY
TIMECODEVIDEOCONTROL
MENU SET SELECTMETERMODE
FINE TRACKING TIMECODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEOCASSETTE RECORDER
BR-D80U
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
P.READ
D9 editing recorder BR-D80E
Front panel
Rear panel
DV connector
SA-DV60E
REMOTE(9P) VCR CONTROL
DV cables (4P-4P, 6P-4P)
9P-9P remote cable
Capturing
Writing back
(VIDEO/AUDIO)
Nonlinear editor
(2) D9 DV nonlinear editing system
Note on the screws
Both millimeter screws and inch screws are
provided in the package. Connect the cable
by attaching the inch screws as described in
the attached document.
Rear panel:
millimeter
screws
Connector panel:
millimeter screws
AC IN 120V 50/ 60Hz
VIDEOOUT
REF
VIDEOIN
YLINE
R-Y
B-YY/C358
Y
R-Y
B-YY/C358
LINE-2
LINE-1
VIDEO AUDIO
MONITOROUT
TIMECODE
ON
OFF 75Ω
DIAGNOSTIC
REMOTE(9P)
VIDEOCONTROL
AUD-1
AUD-2
AUD-1
AUD-2
AUDIOIN AUDIO OUT
LEVEL
-6dB +4dB
LEVEL
-6dB +4dB
IN OUT
DVIN/OUT
VTRCTRL
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSONSCREENTIMECODESYSTEM
STANDBY
TIMECODEVIDEOCONTROL
MENU SET SELECT
METERMODE
FINE TRACKING TIME CODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEOCASSETTE RECORDER
BR-D80U
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
P.READ
D9 editing recorder BR-D80E
Front panel
Rear panel
DV connector
SA-DV60E
REMOTE(9P) VCR CONTROL
DV cable (4P-4P)
9P-9P remote cable
(VIDEO/AUDIO)
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
STATUSSHUTTER
MENU
FILTER
1 3200k
2 5600k
3 5600k+ND
POWER
NG
GAINOUTPUTWHT.BAL
VTR
ON OFF
ALARM
MONITOR
SAVESTBY
HML
BARSCAM
AUTOKNEE
PRSTAB
ON
OFF
CH-1 CH-2
AUDIO
LEVEL
AUTOIRIS LOLUX
BACKL
NORMAL
SPOTL
STRETCH
NORMAL
COMPRESS
FULLAUTOBLACK
DV camcorder GY-DV500E
V.IN/A.MONI A.OUT COUNTER
DV CTL
TC
UB
CH-1/2
CH-3/4
Y/C
(CPN)
LINE
L
R
MIX
MIX
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET
SELECT
SHIFT
MENU
HOLD SHIFT A. DUB
ADVANCE PRESET
REW STOP FF
REC PLAY
PAUSE
ON/OFF
MENU
OVER
OVER
HMSF
AUDLOCK
SP
32k 48k
SLAVE PB NDF
SERVO RF
DEW
AUTO OFF
HOLD
CH 2/4
CH 1/3
VIDEO CASSETTE RECORDER BR-DV600UA
dB4030 20 10 0
DV recorder BR-DV600EA
DV connector
DV connector
(3) DV D9 dubbing system
Connect either one
of the DV recorder
or the Camcorder to
the interface board
E
U
All manuals and user guides at all-guides.com
all-guides.com

(U-6)
Screw
Top cover
Screw
Board stopper
Lugs
Lugs
1
2
Installation procedures
1. Loosen two screws on the upper
surface of the VCR as shown on
the left and remove the top
cover. The screws cannot be
pulled out.
Handle with care. The sharp
edges of the top cover and
VCR chassis may hurt your
hands.
2. Remove the board stopper.
1) Loosen the screw slightly.
2) Move the board stopper in the
direction shown by the arrow.
3. Lift up the rear side of the board
stopper and remove it.
Six lugs are installed in the
chassis in areas in contact
with the top cover. When
removing the top cover, be
careful not to remove these
lugs as well.
WARNING
Make sure that the VCR is OFF and its power cord unplugged from the power outlet before
proceeding with the installation. Otherwise, a fire or electric shock hazard may result.
3. Installation
CAUTION
Although installation is possible by adopting the following procedures, such work is
accompanied with a risk of electric shock or injury and special tools are required. It is
therefore recommended to have any installation work performed by a JVC-authorized
agent. Please note that there will be a fee for any installation work.
(E-8)
(U-7)
3. Installation (continued)
AC IN 100V 50/ 60Hz
VIDEO OUT
Y
R-Y
B-YY/C 358
LINE-2
LINE-1
VIDEO AUDIO
MONITOR OUT
TIME CODE
DA1
DA2
DA1
DA2
AUDIO IN AUDIO OUT
LEVEL
- 6dB + 4dB
LEVEL
- 6dB + 4dB
IN OUT
Screw
Cover
AC IN 100V 50/ 60Hz
VIDEO OUT
Y
R-Y
B-YY/C 358
LINE-2
LINE-1
VIDEO AUDIO
TIME CODE
DA1
DA2
DA1
DA2
AUDIO IN AUDIO OUT
LEVEL
- 6dB + 4dB
LEVEL
- 6dB + 4dB
IN OUT
DV IN/OUT
VTR CTRL
ScrewConnector
section
Cables
Board
4. Remove one screw on the rear
panel of the VCR and remove
the cover for installation of
options. Use the removed screw
to install the connector section.
5. Pass the cables connected to
the connector section through
the inside of the VCR, install the
unit as shown and secure it with
the screw removed in procedure
4.
6. Insert the board in the slot with
the correct board orientation.
Insert the board in the 5th slot
counted from the rear side.
If the SA-D80U or SA-D50U has
already been installed in that
slot, replace it with this board.
(E-9)
All manuals and user guides at all-guides.com

(U-8)
7. Connect the cables to the connection pins CN302 (for 7-pin plug) and
CN202 (for 6-pin plug) on the DV I/O board section.
3. Installation (continued)
Clamps Cables
Ferite core
Head phone
Phones
8. Fix the connected cables with clamps (3 points) as shown in the figure.
9. Re-install the board stopper and secure it.
10. Replace the top cover on the VCR and tighten the screws loosened in
procedure 1 to secure it.
11. Attach the ferrite core.
If you use headphones, attach the ferrite core, provided in the package, as
shown above.
(E-10)
—MEMO —
All manuals and user guides at all-guides.com

(U-9)
4.
Switch Settings and Connection of a D9 or DV Device
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE / STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSON SCREENTIME CODESYSTEM
STAND BY
TIME CODEVIDEO CONTROL
MENU SET SELECTMETER MODE
FINE TRACKING TIME CODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEO CASSETTE RECORDER
BR-D80
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
INT/EXT switch
VIDEO INPUT switch
AUDIO INPUT switch
Connection
•To perform timecode dubbing from a D9 device to a DV device, be sure to connect the
REMOTE (9-pin) connector on the D9 main body and the VCR CONTROL connector on the
SA-DV60U using the provided 9-pin cable.
•Timecode dubbing from a DV device to a D9 device does not need the 9-pin cable.
Settings
䡵When using a D9 device as the recorder:
Set the switches on the D9 device as follows.
Always set the VIDEO INPUT and AUDIO
INPUT switches as shown below. The use
of other settings may lead to a malfunction.
Be sure to turn the unit OFF before chang-
ing the positions of the VIDEO INPUT and
AUDIO INPUT switches. Otherwise, noise
may be produced during output.
1. Settings for recording a DV input signal
on the D9 device
•Front panel
VIDEO INPUT switch: Set to DIG.
AUDIO INPUT switch: Set to DIG.
2. Settings for timecode dubbing from the
BR-DV600UA to the D9 device
•Front panel
VIDEO INPUT switch: Set to DIG.
AUDIO INPUT switch: Set to DIG.
•Time code switch:
INT/EXT switch: Set to EXT.
•Menu switch
No. 409 EXT REGEN TC: Set to VITC.
䡵When using a DV device as the recorder:
Set the switches on the DV device as follows.
1. Settings for recording DV input signals
on a DV device
Set the input of the DV device to IEEE1394
(digital).
2. Settings for timecode dubbing from a D9
device to the BR-DV600UA
•Menu switches
No. 460 TC DUPLICATE (1394): Set to ON.
No. 416 NON DROP/DROP:
Set according to the recording mode of
the D9 device.
MEMO
•Timecode dubbing is not available with the
BR-DV600U.
3. Settings for recording timecodes from the
BR-DV600UA as sub-timecodes
•Menu switch
No. 450 SUB TC (VITC) REC: Set to ON.
No.451 VITC OUT SELECT: Set to SUB TC.
(E-11)
4.
Switch Settings and Connection of a D9 or DV Device
POWER
ON
OFF
HM FS
COUNTER
CTL
TC
UB
REMOTE
LOCAL
9PIN
AUDIO
MONITOR
AUDIO
INPUT
VIDEO
INPUT
DA1
MIX
DA2
DIG
LINE
Y/C
(CPN)
DIG
ANA
REC PLAY PAUSE/ STILL
REW STOP FF
EJECT SEARCH
PHONES LEVEL
AUDIO REC LEVEL
DA-2DA-1
TRACKING
SERVO VIDEO1 VIDEO2 USER
OTHERSON SCREENTIME CODESYSTEM
STAND BY
TIME CODEVIDEO CONTROL
MENU SET SELECTMETER MODE
FINE TRACKING TIME CODE GEN.
SET HOLD
COUNTER
RESET
SYSTEM
PHASE
SC
PHASE
VIDEO
PHASE
INT REC PRESET
REGENFREEEXT
CHANNEL
CONDITION
CTL SERVO AUTO OFF
DFEMP JOG
GEN
VIDEO CASSETTE RECORDER
BR-D80
OVER OVER
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-25
-30
-40
-60
-15
-16
-17
-18
-19
-20
-21
-22
-23
-24
0
-4
-8
-12
-16
-20
-30
-40
-60
-25
STILL
X-1
REV FWD
X1
DA2/TRACKINGDA1
INT/EXT switch
VIDEO INPUT switch
AUDIO INPUT switch
Connection
•To perform timecode dubbing from a D9 device to a DV device, be sure to connect the
REMOTE (9-pin) connector on the D9 main body and the VCR CONTROL connector on the
SA-DV60E using the provided 9-pin cable.
•Timecode dubbing from a DV device to a D9 device does not need the 9-pin cable.
Settings
䡵When using a D9 device as the recorder:
Set the switches on the D9 device as follows.
Always set the VIDEO INPUT and AUDIO
INPUT switches as shown below. The use
of other settings may lead to a malfunction.
Be sure to turn the unit OFF before chang-
ing the positions of the VIDEO INPUT and
AUDIO INPUT switches. Otherwise, noise
may be produced during output.
1. Settings for recording a DV input signal
on the D9 device
•Front panel
VIDEO INPUT switch: Set to DIG.
AUDIO INPUT switch: Set to DIG.
2. Settings for timecode dubbing from the
BR-DV600EA to the D9 device
•Front panel
VIDEO INPUT switch: Set to DIG.
AUDIO INPUT switch: Set to DIG.
•Time code switch:
INT/EXT switch: Set to EXT.
•Menu switch
No. 409 EXT REGEN TC: Set to VITC.
䡵When using a DV device as the recorder:
Set the switches on the DV device as follows.
1. Settings for recording DV input signals
on a DV device
Set the input of the DV device to IEEE1394
(digital).
2. Settings for timecode dubbing from a D9
device to the BR-DV600EA
•Menu switches
No. 460 TC DUPLICATE (1394): Set to ON.
MEMO
•Timecode dubbing is not available with the
BR-DV600E.
•The GY-DV500E and G-DY700WE models
are not capable of DV input recording.
3. Settings for recording timecodes from the
BR-DV600EA as sub-timecodes
•Menu switch
No. 450 SUB TC (VITC) REC: Set to ON.
No.451 VITC OUT SELECT: Set to SUB TC.
E
U
All manuals and user guides at all-guides.com

(U-10)
5. Precautions for Use of DV Input/Output
1. When a signal recorded in WIDE mode is dubbed from a D9 device to a DV device, the
WIDE ID signal will be lost.
When viewing a dubbed tape on a widescreen monitor, set the monitor to the WIDE mode
manually.
2. A copy-guarded signal cannot be dubbed because both the video and audio are muted.
3. With certain DV devices, when the audio output of the D9 device is high, the OVER
indicator on the DV device may light up while the signal meter on the D9 device does not
indicate an OVER level. This is due to an error in the accuracy of the meter of the DV
device or a difference in the dynamic range between the devices, and not to a malfunction
of the SA-DV60U.
4. When the audio input is a 4-channel signal with a 32k sampling frequency, the audio will
be recorded only in channels 1 and 2, and not in channels 3 and 4.
5. When a D9 device is supplied with DV input and the connected DV device is in Still or
Search mode, the audio signal of the DV input is muted.
6. The DIP switch (S301) on the SA-DV60U has been preset at the factory as shown below.
Do not alter the setting of this switch.
S301
SA-DV60U
Switch bits 3 & 8 at low positions.
All other switch bits at high positions.
1
2
3
4
5
6
7
8
7. Although with certain DV devices the audio EE output from the DV device may be out of
phase, recording is performed normally.
8. It is not possible to perform editing between D9 devices.
(E-12)
5. Precautions for Use of DV Input/Output
1. When a signal recorded in WIDE mode is dubbed from a D9 device to a DV device, the
WIDE ID signal will be lost.
When viewing a dubbed tape on a widescreen monitor, set the monitor to the WIDE mode
manually.
2. A copy-guarded signal cannot be dubbed because both the video and audio are muted.
3. With certain DV devices, when the audio output of the D9 device is high, the OVER
indicator on the DV device may light up while the signal meter on the D9 device does not
indicate an OVER level. This is due to an error in the accuracy of the meter of the DV
device or a difference in the dynamic range between the devices, and not to a malfunction
of the SA-DV60E.
4. When the audio input is a 4-channel signal with a 32k sampling frequency, the audio will
be recorded only in channels 1 and 2, and not in channels 3 and 4.
5. When a D9 device is supplied with DV input and the connected DV device is in Still or
Search mode, the audio signal of the DV input is muted.
6. The DIP switch (S301) on the SA-DV60E has been preset at the factory as shown below.
Do not alter the setting of this switch.
S301
SA-DV60E
Switch bit 3 at low position.
All other switch bits at high positions.
1
2
3
4
5
6
7
8
7. Although with certain DV devices the audio EE output from the DV device may be out of
phase, recording is performed normally.
8. It is not possible to perform editing between D9 devices.
E
U
All manuals and user guides at all-guides.com