JVC VN-T16U User manual

LST1367-001B
HD IP CAMERA
VN-T16U QUICK GUIDE
Thank you for purchasing this product.
Before operating this unit, please read the "INSTRUCTIONS", "QUICK GUIDE" and
"SAFETY PRECAUTIONS" carefully to ensure the best possible performance.
For Customer Use:
Enter below the Serial No. which is located on the
body. Retain this information for future reference.
Model No. VN-T16U
Serial No.

1
Contents
1 Introduction ........................................................................................................................................................................2
Unpack Everything.........................................................................................................................................................2
Operationg Precautions .................................................................................................................................................2
Prepare for Installation................................................................................................................................................... 3
Mount the Camera .........................................................................................................................................................3
Dimensions and Connect the Wiring..............................................................................................................................4
Network Setup................................................................................................................................................................6
Setting IP ................................................................................................................................................................6
Connecting the Camera to a Personal Computer ...................................................................................................6
Using “IP Finder” to Search Camera’s IP Address .........................................................................................................9
2 Warnings..........................................................................................................................................................................10
3 Dimensions.......................................................................................................................................................................10
4 Specifications...................................................................................................................................................................11
Contents of this manual
Windows and Internet Explorer are registered trademarks of Microsoft
Corporation in the U.S.
Pentium is a registered trademark of Intel Corporation in the U.S.
AMD is trademark of Advanced Micro Devices Inc. in the U.S.
Product names of other companies described in this manual are trademarks
or registered trademarks of the respective companies. Symbols such as ™,
® and © are omitted in this manual.
Design, specifications and other contents described in this manual are
subject to change for improvements without prior notice.

2
1 Introduction
Thank you for purchasing the camera. Before installing it, please verify your model and read this guide carefully. See the
INSTRUCTIONS located on CD-ROM for more information about setting up your camera.
This manual is designed for administrators and users of the network camera. Please read it carefully before use. All
requirements should be followed before using this camera. Keep this document for future reference.
Unpack Everything
HD IP CAMERA
WARRANTY CARD
SAFETY PRECAUTIONS
QUICK GUIDE
8-PIN TERMINAL BLOCK for alarm input/output
CD-ROM containing INSTRUCTIONS and IP Finder software
Operating Precautions
■Storage and Operating Environment
This camera has designed for indoor use. It cannot be
used outdoors.
Do not install the camera in following places
･In a place exposed to rain or moisture.
･In a place with vapor or oil, for example in a kitchen.
･When the ambient temperature rises above or falls
below the acceptable range (from -10℃to 50℃)
･In a place at which corrosive gases are emitted.
･Near a source of radiation, X-rays, strong radio waves or
magnetism.
･In a place subject to vibration.
･In a place with excessive dirt.
■Maintenance
Wipe the camera with a dry, soft cloth to remove any dirt.
Do not use benzene or thinner to wipe the camera. Doing
so may melt the surface or cause it to fog. For tough stains,
wipe with a neutral detergent diluted with water, followed
by wiping with a dry cloth.
■Power supply
Please make sure the power source is DC 12 V / AC 24 V
/ PoE. Only connect the camera to this power system.
The AC 24 V and DC 12 V power supply shall conform to
the following: Class 2 only (For USA), Isolated power
supply only (For Europe).
When using AC 24 V power supply, do not connect the
power cable to commercial power supply. If it is connected
by mistake, the internal circuit may be damaged. Do not
use the camera and make sure to send it to the nearest
JVC dealer for inspection.
■Real Time Clock
The real time clock of the camera will be initialized by
power off over 3 days. In such case, please set data/time
manually, or set NTP server.
If the real time clock is initialized, event log, data in SD
card, and mail sent by the camera do not show correct
time.
■SD Card
SD card is fragile and not reliable for long term use. Our
company will not be liable for damages resulting from the
use of SD card. Frequent back up of data is
recommended. Data of SD card will be lost by troubles
below.
･Electrical or Mechanical Shock to SD card.
･Power off or ejecting of SD card during recording.
･Rewriting times exceeds upper limit of the SD card (The
upper limit depends on grade of the SD card.)

3
■Energy Conservation
When the camera is not in use for a long time, turn off the
power for safety and energy conservation reasons.
■Copyright Protection
With the exception of the user being the copyright holder
or when permission such as for duplication has been
granted by the copyright holder, permission is required in
principle for the duplication, modification, or transmission
of copyrighted material.
Unauthorized duplication, modification, or transmission of
copyrighted material may constitute a copyright
infringement, and the user may be liable to compensate
for any damages. When using copyrighted material, be
sure to check the license agreement of the copyrighted
material thoroughly.
When rights or rights holders are involved with regard to
the targeted duplicating subject, permission may be
required for shooting or using (processing) it. Be sure to
check the licensing conditions thoroughly.
■Disclaimer
We will not be responsible for any inconveniences or
disturbances caused in the event of privacy invasion as a
result of camera footages of this product.
■Others
Because the camera controls auto exposure by shutter
speed, flicker can be shown by fluorescent light. To
reduce the flicker, please select PAL mode if the power is
50Hz, or NTSC mode if the power is 60Hz. (Refer to
INSTRUCTIONS “4 Overview of Navigation and Controls”
- “Video Type”)
Prepare for Installation
Select the lens to use with your camera. This camera supports the use of a manual iris or DC iris
lens. When using a DC iris lens, it should be connected to the camera via the 4-pin square socket
located at the side of the camera.
Mount the Camera
1. Attach the camera to a pending mount.
Insert the screws on the camera stand into either of the screw holes on the base. Then tighten
them up.
2. Mount the camera onto the ceiling/wall and fasten it securely.
3. Connect the Safety Wire (Fall Prevention Wire, not supplied) to the camera and the wall/ceiling.
Warning
To prevent the camera from falling off, ensure that it is connected to a firm place
(ceiling slab or channel) using a Safety Wire (Fall Prevention Wire is not
supplied).
Pay also careful attention to the length, strength, wiring, and material (insulating
properties) of a Safety Wire (fall prevention wire) to be used. The length should
be as short as possible within the permissible range of the mounting length. The
wire should be strong enough to withstand the total weight of this product and the
fixer. (Pay also attention to the finishing at the end of the wire.) The thickness of
the wire’s end of camera side should be less than 1 mm.
Caution
Must be isolated camera and the wall/ceiling which are connected by a Safety
Wire (Fall Prevention Wire).

4
Dimensions and Connect the Wiring
Lens is not provided.
2
3
Safety Wire (Fall Prevention Wire,
not provided)

5
1. CS mount: connect the 1/3-type CS mount lens with the camera
2. Screw: lock Back focus Adjustment
3. Back focus Adjustment
4. Base: connect the camera with the tripod
5. SD card slot: insert a SD card into this slot for recording and storage
6. Video: not supported (for factory use only)
7. RJ45 Ethernet Connector/ PoE: insert the RJ45 cable for network connection. It also supports
PoE (Power over Ethernet).
8. Default Button: reset all of the camera parameters to factory default by pushing 5 seconds.
9. Reset Button: restart the system.
10.Power Indicator: Red light indicates power connection.
11.I/O Connector: Input/Output Connector
12.Power Terminal
Note
Connectors and field wiring terminals for external Class 2 circuits provided with
marking indicating minimum Class of wiring to be used. Class 2 shall be marked
adjacent to the field wiring terminals.
Caution
To avoid damage to the camera, never connect more than one type of power supply
(PoE or DC12V or AC24V power plug) at the same time.
A/I
Audio in
GND
A/O
Audio out
GND
AO
Alarm out
COM
AI
Alarm in
GND

6
Network Setup
Setting IP This is a network-based camera and must be assigned an IP address first.
The camera’s default IP address is 192.168.0.2 and sub mask is 255.255.255.0. To change IP
address, open Network Settings page described later.
If your network uses a DHCP server, an IP address can be assigned automatically from the DHCP
server by enabling DHCP in the Network Settings page described later.
Connecting the Camera to a Personal Computer
1. Connect the network cable to the camera and then turn on the camera’s power.
2. Set the personal computer’s IP address. The camera’s default IP address is 192.168.0.2 and sub
mask is 255.255.255.0.
3. Check that the camera and computer are connected by Pinging the IP address you have set. To
do this, start a command prompt (Windows: from the Start Menu, select Program. Then select
Accessories and choose Command Prompt.) Type: Ping 192.168.0.2. If the message “Reply
from…” appears, it means the connection is done.
4. Start Internet Explorer and enter IP address: 192.168.0.2. A login window will appear. Enter the
default user name: admin and password: jvc to log in.
5. Images of the camera can be viewed through Internet Explorer. Before viewing, follow these
steps to enable the display.
a. Enable Cookies as shown below:
In Internet Explorer, click Internet Options on the Tools menu.
On the Privacy tab, move the settings slider to Low or Accept All Cookies.
Click OK.
b. When a proxy server is used, click Internet Options on the Tools menu of Internet Explorer,
select Connect tab, click LAN button, and set proxy server.
c. Change Security in Internet options as shown below:
On tool menu, click Internet Option.
Press the Security tab.
If the camera operates inside the Intranet, click the Intranet icon. If the camera operates on
the Internet, click the Internet icon.

7
In Windows 7 only, Click【Tools】【Internet Options】【Security】
Enable Protected Mode (require restarting Internet Explorer) Unchecked
Click Custom Level. This will open the Security Settings –Internet Zone screen.
Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:
【Download signed ActiveX controls】Prompt (recommended)
【Download unsigned ActiveX controls】Prompt
【Initialize and script ActiveX not marked as safe for scripting】Prompt

8
【Automatic prompting for ActiveX controls】Enable
【Run ActiveX controls and plug-ins】Enable
【Script ActiveX controls marked safe for scripting*】Enable
Press OK to save the settings. Close all Internet Explorer windows and start a new window.
This will allow the new settings to take effect.

9
6. Type your setting IP address into the browser.
7. Then you should be able to see the camera image screen.
Using “IP Finder” to Search Camera’s IP Address
The IP Finder is a tool which helps users to find VN-T16/216 series network cameras in the LAN
which your computer is connected. Please note that IP Finder is only compatible with Windows 7,
windows Vista and Windows XP.
1. Insert the CD-ROM in the CD-ROM drive.
2. Copy the IP Finder’s folder to your computer.
3. Double click the IpFinder.exe in your computer’s IP Finder folder. An IP Finder window will pop
out. The window will display a list of IP cameras which you are using currently.
4. Press Search to search cameras.

10
2 Warnings
Installation and maintenance should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
DANGER! AC24V models require the use of CSA Certified/UL Listed Class 2 power adapters to
ensure compliance with electrical safety standards. Power over Ethernet (PoE) should meet the
IEEE 802.3af. PoE standard.
3 Dimensions

11
4 Specifications
Operational Specifications
Image device
1/2.7-type Mega-pixel CMOS sensor
Sensitivity
Color: 0.6 lx, B/W: 0.6 lx (50％F1.2)
Day/Night
Easy D/N
Auto Gain Control
Off/On, selectable
Auto Iris Control
AES (Automatic Electric Shutter)
White Balance
ATW (2800K～8500K) and Manual
Electric Shutter
NTSC: 1/30~1/10000 sec
PAL: 1/25~1/10000 sec
Noise Reduction
Yes
Motion detection
Yes
Lens Mount
1/3-type CS mount
(with easy back focus adjustment)
BLC
Yes
Audio
Line in/out
Alarm
1 in / 1 out (Alarm out spec: 0.5 A / AC 120 V max)
IP Specifications
Video Compression
H.264 & MPEG4 & MJPEG
Video Streaming
Real time stream:
1080P H.264 or 720P H.264+D1 or D1+D1
Independent controllable frame rate and
bandwidth. Constant or variable bitrate control
Resolution
NTSC: 1080P(1920 x 1080), 720P(1280 x 720),
D1(720 x 480), 4CIF(704 x 480), VGA(640 x 480),
CIF(352 x 240), QVGA(320 x 240)
PAL: 1080P(1920 x 1080), 720P(1280 x 720),
D1(720 x 576), 4CIF(704 x 576), VGA(640 x 480),
CIF(352 x 288), QVGA(320 x 240)
Image Frame Rate
NTSC: Up to 30 fps
PAL: Up to 25 fps

12
Security
Multiple user access levels with password
protection
Users
1 Administrator, 5 Users
Video Access from Web
Browser
Full control of all camera settings available to
administrator
Minimum Web
Browsing Requirements
Windows XP or Windows 7 as OS,
Internet Explorer Version 6.0-9.0,
CPU: Intel Pentium 4 2.4 GHz or equivalent AMD,
Memory: 1 GB or above
Supported Protocols
IPv4, HTTP, TCP, RTSP, RTP, ICMP, UDP, IGMP,
RTCP, FTP, DNS, DHCP, ARP
Network interface
RJ-45, 100BASE-TX/10BASE-T,
FULL/HALF/Auto negotiation
Surveillance Protocol
ONVIF Compatible (pass compliance test tool)
Onboard Storage
SDHC (suggest class 10)
Electrical
Power Supply
PoE IEEE 802.3af Class 0, DC 12 V, AC 24 V
Power Consumption
PoE 0.13 A, DC 12 V 550 mA
Mechanical
Dimension
56 mm (H) x 69 mm (W) x 125 mm (L)
Weight
390 g
Connectors
Power Input: spring terminal
Network: RJ45 connector
Audio In/out: removable terminal block
Alarm In/out: removable terminal block
Environmental
Operating Temperature
-10 °C to 50 °C
Operating Humidity
20 % to 90 % (without condensation)
Storage Temperature
-20 °C to 60 °C

13

14

15
©2012 JVC KENWOOD Corporation