JVC KD-X462BT User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
ไทย
B5A-2627-10 [M]
KD-X462BT / KD-X368BT
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
ตัวรับสื่อดิจิตอล
คูมือการใชงาน
JS_JVC_KD_X462BT_M_C_10.indd 1JS_JVC_KD_X462BT_M_C_10.indd 1 8/24/2018 9:27:25 AM8/24/2018 9:27:25 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2ENGLISH
BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings
and Cautions in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe driving.
• Do not ingest the battery, Chemical Burn Hazard.
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
(page 36). Turn off the unit when parking at a low ceiling area.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CONTENTS
BEFORE USE 2
BASICS 3
GETTING STARTED 5
1 Cancel the demonstration
2 Set the clock and date
3 Set the basic settings
RADIO 7
AUX 9
USB/iPod/ANDROID 9
Spotify 11
BLUETOOTH® 13
AUDIO SETTINGS 21
DISPLAY SETTINGS 27
REFERENCES 29
Maintenance
More information
TROUBLESHOOTING 32
INSTALLATION/
CONNECTION 34
SPECIFICATIONS 38
How to read this manual
• Operations are explained mainly using buttons on the faceplate of KD-X462BT and KD-X368BT.
• English indications are used for the purpose of explanation. You can select the display language from the menu. (Page 6)
• [XX] indicates the selected items.
• (Page XX) indicates references are available on the stated page.
JS_JVC_KD_X462BT_M_EN_1.indd 2JS_JVC_KD_X462BT_M_EN_1.indd 2 6/5/2018 11:05:56 AM6/5/2018 11:05:56 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate
Turn on the power Press BSRC.
• Press and hold to turn off the power.
Adjust the volume Turn the volume knob.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. The volume level returns to the previous level before muting or pause.
Select a source • Press BSRC repeatedly.
• Press BSRC, then turn the volume knob within 2 seconds.
Change the display information Press repeatedly. (Page 30)
Select an item 1 Turn the volume knob to select an item.
2 Press the knob to confirm.
Attach
How to reset
Detach
Faceplate
Reset the unit
within 5 seconds
after detaching the
faceplate.
KD-X462BT:
Volume knob
Remote sensor
(Do not expose to
bright sunlight.)
Detach button
Source button
Display window
JS_JVC_KD_X462BT_M_EN_1.indd 3JS_JVC_KD_X462BT_M_EN_1.indd 3 6/5/2018 11:05:59 AM6/5/2018 11:05:59 AM

4ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASICS
To On the faceplate
Turn on the power Press SRC-B.
• Press and hold to turn off the power.
Adjust the volume Press VOL +/– .
• Press and hold VOL + to continuously increase the volume to 15.
Press *ENTER to mute the sound or pause playback.
• Press again to cancel. The volume level returns to the previous level before muting or pause.
Select a source • Press SRC-Brepeatedly.
• Press SRC-B, then press VOL +/– within 2 seconds.
Change the display information Press repeatedly. (Page 31)
Select an item 1 Press VOL +/– to select an item.
2 Press *ENTER to confirm.
Attach
How to reset
Detach
Faceplate
Reset the unit
within 5 seconds
after detaching the
faceplate.
KD-X368BT:
Detach button
Source button
Display window
Symbolic button
Remote sensor
(Do not expose to
bright sunlight.)
JS_JVC_KD_X462BT_M_EN_1.indd 4JS_JVC_KD_X462BT_M_EN_1.indd 4 6/5/2018 11:06:00 AM6/5/2018 11:06:00 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASICS
Remote control (RM-RK52)
Aim the remotely control directly at the remote sensor on
the unit. (Page 3 or 4)
To On the remote control
Adjust the volume Press VOL + or VOL – .
• Press and hold VOL + to continuously
increase the volume to 15.
Press dto mute the sound or pause
playback.
• Press again to cancel. The volume
level returns to the previous level
before muting or pause.
Select a source Press SOURCE repeatedly.
Pull out the insulation
sheet when using for
the first time.
How to replace the battery
GETTING STARTED
For key layout on the faceplate, see page 3 or page 4.
Cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to [YES] , see
page 6), the display shows:
KD-X462BT:
“CANCEL DEMO” “PRESS” “VOLUME KNOB”
1 Press the volume knob.
[YES] is selected for the initial setup.
2 Press the volume knob again.
“DEMO OFF” appears.
KD-X368BT:
“CANCEL DEMO” “PRESS ENTER”
1 Press *ENTER.
[YES] is selected for the initial setup.
2 Press *ENTER again.
“DEMO OFF” appears.
Set the clock and date
1 Press and hold .
2 Perform ‘Select an item (page3 or 4)’ operation to select [CLOCK] .
3 Perform ‘Select an item (page3 or 4)’ operation to adjust the clock.
[CLOCKADJUST] set the hour and minute [CLOCKFORMAT] [12H] or [24H]
4 Perform ‘Select an item (page3 or 4)’ operation to set the date.
[DATESET] set the day, month and year
5 Press to exit.
To return to the previous setting item, press .
1
2
JS_JVC_KD_X462BT_M_EN_1.indd 5JS_JVC_KD_X462BT_M_EN_1.indd 5 6/5/2018 11:06:01 AM6/5/2018 11:06:01 AM

6ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Set the basic settings
1 Press and hold .
2 Perform ‘Select an item (page3 or 4)’ operation to select an
item (see the following table).
3 Repeat step 2 until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[SYSTEM]
[KEY BEEP] (Not applicable when 3-way crossover is selected.)
[ON]: Activates the keypress tone. ; [OFF]: Deactivates.
[SOURCE SELECT]
[AM SRC]*[ON]: Enables AM in source selection. ; [OFF]: Disables. (Page 7)
[SW1 SRC]*[ON]: Enables SW1 in source selection. ; [OFF]: Disables. (Page 7)
[SW2 SRC]*[ON]: Enables SW2 in source selection. ; [OFF]: Disables. (Page 7)
[SPOTIFY SRC]*[ON]: Enables SPOTIFY/SPOTIFY BT in source selection. ; [OFF]: Disables.
(Page 11)
[BUILT-IN AUX]*[ON]: Enables AUX in source selection. ; [OFF]: Disables. (Page 9)
[F/W UPDATE]
[UPDATE SYSTEM]
[F/W UP xxxx] [YES]: Starts upgrading the firmware. ; [NO]: Cancels (upgrading is not
activated).
For details on how to update the firmware, visit
<http://www.jvc.net/cs/car/>.
* Not displayed when the corresponding source is selected.
3
[FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ;
[NO]: Cancels.
[CLOCK]
[TIME SYNC] [ON]: The clock time is automatically set using the Clock Time (CT) data
in FM Radio Data System signal. ; [OFF]: Cancels.
[CLOCK DISPLAY] [ON]: The clock time is shown on the display even when the unit is
turned off. ; [OFF]: Cancels.
[ENGLISH] Select the display language for menu and music information if applicable.
By default, [ENGLISH] is selected.
[ESPANOL]
GETTING STARTED
JS_JVC_KD_X462BT_M_EN_1.indd 6JS_JVC_KD_X462BT_M_EN_1.indd 6 6/5/2018 11:06:02 AM6/5/2018 11:06:02 AM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
For key layout on the faceplate, see page 3 or page 4.
Search for a station
1 Press source button repeatedly to select FM, AM, SW1 or SW2.
2 Press S/ T(or press H/ Ion the remote control) to search for a
station automatically.
(or)
Press and hold S/ T(or press and hold H/ Ion the remote
control) until “M” flashes, then press repeatedly to search for a station
manually.
• “ST” or “STEREO” lights up when receiving an FM stereo broadcast with
sufficient signal strength.
• The unit switches to FM alarm automatically when receiving an alarm
signal from FM broadcast.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM/SW1/SW2.
Store a station
While listening to a station...
Press and hold one of the number buttons (1 to 6).
(or)
1 Press and hold the following button until “PRESETMODE” flashes.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
2 Perform ‘Select an item (page3 or 4)’ operation to select a
preset number.
“MEMORY” appears once the station is stored.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press .
2 Perform ‘Select an item (page3 or 4)’ operation to select a
preset number.
Other settings
1 Press and hold .
2 Perform ‘Select an item (page3 or 4)’ operation to select an item (see
the table on page8).
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_X462BT_M_EN_1.indd 7JS_JVC_KD_X462BT_M_EN_1.indd 7 6/5/2018 11:06:03 AM6/5/2018 11:06:03 AM

8ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Default: [XX]
[TUNERSETTING]
[RADIO TIMER] Turns on the radio at a specific time regardless of the current source.
1 [ONCE]/[DAILY]/[WEEKLY]/[OFF]: Select how often the timer will be
turned on.
2 [FM]/[AM]/[SW1]/[SW2]: Select the source.
3 [01] to [18] (for FM)/[01] to [06] (for AM/SW1/SW2): Select the preset
station.
4 Set the activation day*1 and time.
“
 ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AMSRC]/[SW1SRC]/[SW2SRC] in [SOURCESELECT]
after Radio Timer for AM/SW1/SW2 is selected. (Page 6)
[SSM] [SSM01–06]/[SSM07–12]/[SSM13–18]: Automatically presets up to 18
stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select
[SSM07–12]/[SSM13–18] to store the following 12 stations.
[LOCAL SEEK] [ON]: Searches only AM/SW1/SW2 stations with good reception. ;
[OFF]: Cancels.
• Settings made are applicable only to the selected source/station. Once you
change the source/station, you need to make the settings again.
[IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.) ; [WIDE]: Subjects to
interference noises from adjacent FM stations, but sound quality will not be
degraded and the stereo effect will remain.
[MONO SET] [ON]: Improves the FM reception, but the stereo effect will be lost. ;
[OFF]: Cancels.
[NEWSSET]*2 [ON]: The unit will temporarily switch to News Programme if available. ;
[OFF]: Cancels.
RADIO
[REGIONAL]*2 [ON]: Switches to another station only in the specific region using the “AF”
control. ; [OFF]: Cancels.
[AF SET]*2 [ON]: Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception when
the current reception is poor. ; [OFF]: Cancels.
[TI]*2 [ON]: Allows the unit to temporarily switch to Traffic Information if available
(“TI” lights up) while listening to all sources except in AM/SW1/SW2. ;
[OFF]: Cancels.
[PTY SEARCH]*2 Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you have
selected, that station is tuned in.
*1 Selectable only when [ONCE] or [WEEKLY] is selected in step 1.
*2 Selectable only when in FM source.
PTY code
[NEWS], [AFFAIRS], [INFO], [SPORT], [EDUCATE], [DRAMA], [CULTURE], [SCIENCE], [VARIED],
[POP M] (music), [ROCK M] (music), [EASY M] (music), [LIGHT M] (music), [CLASSICS],
[OTHER M] (music), [WEATHER], [FINANCE], [CHILDREN], [SOCIAL], [RELIGION], [PHONE IN],
[TRAVEL], [LEISURE], [JAZZ], [COUNTRY], [NATION M] (music), [OLDIES], [FOLK M] (music),
[DOCUMENT]
JS_JVC_KD_X462BT_M_EN_1.indd 8JS_JVC_KD_X462BT_M_EN_1.indd 8 6/5/2018 11:06:03 AM6/5/2018 11:06:03 AM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
USB/iPod/ANDROID
Start playback
The source changes automatically and playback starts.
KD-X368BT:
KD-X462BT:
*1 Do not leave the cable inside the car when not using.
*2 You can control Android device using the Android device itself via other media player
applications installed in the Android device.
Preparation:
You can listen to music from a portable audio player via the auxiliary input
jack.
• Select
[ON] for [BUILT-IN AUX] in [SOURCESELECT] . (Page 6)
Start listening
1 Connect a portable audio player (commercially available).
2 Press source button repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
3.5 mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
AUX
Auxiliary input jack
3.5 mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
KD-X368BT:
KD-X462BT:
USB input terminal
USB input terminal
USB 2.0 cable*1
(commercially available)
USB cable*1
(commercially available)
Accessory of the iPod/iPhone*1
USB
iPod/iPhone
ANDROID*2
JS_JVC_KD_X462BT_M_EN_1.indd 9JS_JVC_KD_X462BT_M_EN_1.indd 9 6/5/2018 11:06:03 AM6/5/2018 11:06:03 AM

10 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
For key layout on the faceplate, see page 3 or page 4.
To On the faceplate On the remote control
Reverse/
Fast-forward*3
Press and hold S/ T. Press and hold H/ I.
Select a file Press S/ T. Press H/ I.
Select a folder*4 Press 2J/ 1K. Press J/ K.
Repeat play*3*5 Press 4repeatedly.
[TRACK REPEAT] / [FOLDER REPEAT] / [ALL REPEAT] : MP3/WMA/AAC/
WAV/FLAC file
[ONE REPEAT] / [ALL REPEAT] / [REPEAT OFF] : iPod
Random play*3*5 Press 3repeatedly.
[FOLDERRANDOM] / [ALL RANDOM] / [RANDOM OFF] : MP3/WMA/AAC/
WAV/FLAC file
[SONG RANDOM] / [ALL RANDOM] / [RANDOM OFF] : iPod
*3 Not applicable for ANDROID.
*4 This does not work for iPod/ANDROID.
*5 For iPod: Applicable only when [HEAD MODE] is selected.
USB/iPod/ANDROID
Select music drive
While in USB source, press 5MODE repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass
Storage Class).
• Selected drive of a multiple drive device.
Settings to use JVC Remote application
JVC Remote application is designed to control the JVC car receiver’s
operations from the iPhone/iPod (via USB input terminal).
Preparation:
• Install the latest version of JVC Remote application on your
device before connecting.
• For more information, visit <http://www.jvc.net/cs/car/>.
You can make the settings in the same way as connection via
Bluetooth. (Page 19)
Select control mode
While in iPodUSB source (or iPodBT source), press 5MODE
repeatedly.
[HEAD MODE] : Control iPod from this unit.
[IPHONE MODE] : Control iPod using the iPod itself. However, you can
still perform play/pause, file skip, fast-forward or fast-
reverse from this unit.
JS_JVC_KD_X462BT_M_EN_1.indd 10JS_JVC_KD_X462BT_M_EN_1.indd 10 6/5/2018 11:06:04 AM6/5/2018 11:06:04 AM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select a file from a folder/list
For iPod, applicable only when [HEAD MODE] is selected.
1 Press .
2 Perform ‘Select an item (page3 or 4)’ operation to select a
folder/list.
3 Perform ‘Select an item (page3 or 4)’ operation to select a file.
Quick search (applicable only for USB source)
If you have many files, you can search through them quickly.
Perform the following operation to browse through the list quickly.
KD-X462BT: Turn the volume knob quickly
KD-X368BT: Press and hold VOL +/–
Alphabet search (applicable only for iPodUSB source or iPodBT source)
You can search for a file according to the first character.
Perform the following operation to select the desired character (A
to Z, 0to9, OTHERS).
KD-X462BT: Press 2J/ 1Kor turn the volume knob quickly
KD-X368BT: Press 2J/ 1K
• Select “OTHERS” if the first character is other than A to Z, 0 to 9.
• To return to the previous setting item, press .
• To cancel, press and hold .
USB/iPod/ANDROID Spotify
Preparation:
Install the latest version of the Spotify application on your device (iPhone/
iPod touch), then create an account and log in to Spotify.
• Select
[ON] for [SPOTIFY SRC] in [SOURCE SELECT] . (Page 6)
Start listening
1 Start up the Spotify application on your device.
2 Connect your device to the USB input terminal.
KD-X462BT:
KD-X368BT:
3 Press source button repeatedly to select SPOTIFY.
Broadcast starts automatically
* Do not leave the cable inside the car when not used.
USB input terminal
USB input terminal
Accessory of the iPod/iPhone*
Accessory of the iPod/iPhone*
JS_JVC_KD_X462BT_M_EN_1.indd 11JS_JVC_KD_X462BT_M_EN_1.indd 11 6/5/2018 11:06:04 AM6/5/2018 11:06:04 AM

12 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Spotify
To On the faceplate On the remote control
Play back/pause KD-X462BT:
Press the volume knob.
KD-X368BT:
Press *ENTER.
Press d.
Skip a track Press S*1 / T. Press H*1 / I.
Select thumbs up
or thumbs down*2
Press 2J/ 1K. Press J/ K.
Start radio Press and hold 5. ( Not available )
Repeat play*3 Press 4repeatedly.
[ALLREPEAT], [ONE REPEAT]*1,
[REPEATOFF]
( Not available )
Random play*3 Press 3repeatedly*1.
[ALLRANDOM], [RANDOMOFF]
( Not available )
*1 Available for premium account users only.
*2 This feature is available for tracks in Radio only. If thumbs down is selected, the current track is
skipped.
*3 Available for tracks in Playlists only.
Save favorite song information
While listening to the Radio on Spotify...
Press and hold the following button to save the song information.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
“SAVED” appears and the information is stored to “Your Music” or “Your
Library” on your Spotify account.
To unsave, repeat the same procedure.
“REMOVED” appears and the information is removed from “Your Music” or
“Your Library” on your Spotify account.
Search for a song or station
1 Press .
2 Perform ‘Select an item (page3 or 4)’ operation to select a list
type.
The list types displayed differ depending on the information sent from
Spotify.
3 Perform ‘Select an item (page3 or 4)’ operation to select the
desired song or station.
Perform the following operation to browse through the list quickly.
KD-X462BT: Turn the volume knob quickly
KD-X368BT: Press and hold VOL +/–
To cancel, press and hold .
JS_JVC_KD_X462BT_M_EN_1.indd 12JS_JVC_KD_X462BT_M_EN_1.indd 12 6/5/2018 11:06:05 AM6/5/2018 11:06:05 AM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pair and connect a Bluetooth device for the first time
1 Press source button to turn on the unit.
2 Search and select the name of your receiver (“KD-X4 BT”/ “KD-X3 BT”) on the Bluetooth
device.
“BT PAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) KD-X462BT:
“Device Name” “XXXXXX” “VOL–YES” “BACK–NO”
KD-X368BT:
“Device Name” “XXXXXX” “ENTER–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device are the same.
Press the following to confirm the passkey.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
Operate the Bluetooth device to confirm the passkey.
(B) KD-X462BT:
“Device Name” “VOL–YES” “BACK–NO”
KD-X368BT:
“Device Name” “ENTER–YES” “BACK–NO”
Press the following to start pairing.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing. (Page 18)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
BLUETOOTH®
Depending on the operating system and the
firmware version of your mobile phone, Bluetooth
features may not work with this unit.
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the microphone
angle Secure using cord clamps (not
supplied) if necessary.
Microphone input jack
Microphone (supplied)
Rear panel
JS_JVC_KD_X462BT_M_EN_1.indd 13JS_JVC_KD_X462BT_M_EN_1.indd 13 6/5/2018 11:06:05 AM6/5/2018 11:06:05 AM

14 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
“PAIRING COMPLETED” appears when pairing is completed and “” will
light up when the Bluetooth connection is established. For KD-X462BT, the
battery and signal strength of the connected Bluetooth device is shown (see
[FORMAT] on page 27).
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered
in the unit even if you reset the unit. To delete the paired device, see
[DEVICE DELETE] on page 17.
• A maximum of two Bluetooth phones and one Bluetooth audio device can
be connected at any time.
However, while in BT AUDIO source, you can connect to five Bluetooth
audio devices and switch between these five devices. (Page 19)
• Some Bluetooth devices may not automatically connect to the unit after
pairing. Connect the device to the unit manually.
• When the battery of the connected Bluetooth device runs low, “Device
Name” “LOW BATTERY” appears.
• Refer to the instruction manual of the Bluetooth device for more
information.
Auto Pairing
When you connect iPhone/iPod touch to the USB input terminal, pairing
request (via Bluetooth) is automatically activated.
Press the following to pair once you have confirmed the device name.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
Automatic pairing request is activated only if:
– Bluetooth function of the connected device is turned on.
–
[AUTO PAIRING] is set to [ON] . (Page 18)
BLUETOOTH — Mobile phone
For key layout on the faceplate, see page 3 or page 4.
Receive a call
When there is an incoming call:
• The buttons or symbolic button will blink in the color you have selected in
[RING COLOR] . (Page 16)
• The unit answers the call automatically if
[AUTO ANSWER] is set to a selected
time. (Page 16)
During a call:
• The buttons or symbolic button stop blinking and illuminate in the color
you have selected in
[RING COLOR] . (Page 16)
• If you turn off the unit or detach the faceplate, Bluetooth is disconnected.
The following operations may differ or be unavailable depending on the
connected phone.
To On the faceplate On the remote control
First incoming call...
Answer a call Press or the following
button.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
Press J/ K/ H/ I.
Reject a call Press and hold or the
following button.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
Press and hold
J/ K/ H/ I.
End a call Press and hold or the
following button.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
Press and hold
J/ K/ H/ I.
BLUETOOTH®
JS_JVC_KD_X462BT_M_EN_1.indd 14JS_JVC_KD_X462BT_M_EN_1.indd 14 6/5/2018 11:06:08 AM6/5/2018 11:06:08 AM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
To On the faceplate On the remote control
While talking on the first incoming call...
Answer another incoming
call and hold the current
call
Press or the following button.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
( Not available )
Reject another incoming
call
Press and hold or the following button.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
( Not available )
While having two active calls...
End current call and
activate held call
Press and hold or the following button.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
Press and hold
J/ K/ H/ I.
Swap between the current
call and held call
Press .( Not available )
Adjust the phone volume*1
[00] to [35] (Default: [15] )
Perform the following operation during a call.
KD-X462BT: Turn the volume knob
KD-X368BT: Press VOL +/– *2
Press VOL +*2 or
VOL – during a call.
Switch between hands-free
and private talk modes*3
Press during a call. ( Not available )
*1 This adjustment will not affect the volume of the other sources.
*2 Press and hold VOL + to continuously increase the volume to 15.
*3 Operations may vary according to the connected Bluetooth device.
Improve the voice quality
While talking on the phone...
1 Press and hold .
2 Perform ‘Select an item (page3 or 4)’
operation to select an item (see the following
table).
3 Repeat step 2 until the desired item is selected
or activated.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[MIC GAIN] [LEVEL –10] to [LEVEL +10] ([LEVEL –04]):
The sensitivity of the microphone increases as
the number increases.
[NR LEVEL] [LEVEL –05] to [LEVEL +05] ([LEVEL 00]):
Adjust the noise reduction level until the
least noise is being heard during a phone
conversation.
[ECHO CANCEL] [LEVEL –05] to [LEVEL +05] ([LEVEL 00]):
Adjust the echo cancellation delay time until
the least echo is being heard during a phone
conversation.
BLUETOOTH®
JS_JVC_KD_X462BT_M_EN_1.indd 15JS_JVC_KD_X462BT_M_EN_1.indd 15 6/5/2018 11:06:08 AM6/5/2018 11:06:08 AM

16 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Perform ‘Select an item (page3 or 4)’ operation to select an
item (see the following table).
3 Repeat step 2 until the desired item is selected or activated.
To return to the previous setting item, press .
Default: [XX]
[SETTINGS]
[AUTO ANSWER] [01SEC] to [30SEC]: Answers an incoming call automatically in the selected
time (in seconds). ; [OFF]: Cancels.
[RING COLOR] [COLOR01] to [COLOR49] ([COLOR08]): Selects the illumination color for
the buttons or symbolic button as notification when there is an incoming call
and during a call. ; [OFF]: Cancels.
Make a call
You can make a call from the call history, phonebook, or dialing the number.
Call by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
“(First device name)” appears.
• If two Bluetooth phones are connected, press again to switch to
the other phone.
“(Second device name)” appears.
2 Perform ‘Select an item (page3 or 4)’ operation to select an
item (see the following table).
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
To return to the previous setting item, press .
BLUETOOTH®
[RECENT CALL] (Applicable only if the phone supports PBAP.)
1 Press the following button to select a name or a phone number.
KD-X462BT: Volume knob
KD-X368BT: VOL +/–
• “<” indicates call received, “>“ indicates call made, “M” indicates call
missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the following to call.
KD-X462BT: Volume knob
KD-X368BT:
* ENTER
[PHONEBOOK] (Applicable only if the phone supports PBAP.)
1 Press 2 J / 1 K to select the desired letter (A to Z, 0 to 9, and OTHERS).
• “OTHERS” appears if the first character is other than A to Z, 0 to 9.
2 Perform ‘Select an item (page 3 or 4)’ operation to select a name.
3 Perform ‘Select an item (page 3 or 4)’ operation to select a phone
number to call.
• The phonebook of the connected phone is automatically transferred to the
unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” are
showns as “U”.)
[DIAL NUMBER]
1 Perform the following operation to select a number (0 to 9) or character
(, #, +).
KD-X462BT: Turn the volume knob
KD-X368BT: Press VOL +/–
2 Press S / T to move the entry position.
Repeat steps 1 and 2 until you finish entering the phone number.
3 Press the following to call.
KD-X462BT: Volume knob
KD-X368BT:
* ENTER
[VOICE] Speak the name of the contact you want to call or the voice command to
control the phone functions. (See “Make a call using voice recognition” on
page 17.)
JS_JVC_KD_X462BT_M_EN_1.indd 16JS_JVC_KD_X462BT_M_EN_1.indd 16 6/5/2018 11:06:09 AM6/5/2018 11:06:09 AM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Make a call using voice recognition
1 Press and hold to activate the connected phone.
2 Speak the name of the contact you want to call or the voice command
to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press to enter Bluetooth mode.
2 Perform ‘Select an item (page3 or 4)’ operation to select
[RECENTCALL] , [PHONEBOOK] or [DIALNUMBER] .
3 Perform ‘Select an item (page3 or 4)’ operation to select a
contact or enter a phone number.
If a contact is selected, press the following to show the phone number.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
4 Press and hold one of the number buttons (1 to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select
[DIALNUMBER] in step 2
and store a blank number.
BLUETOOTH®
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1 to 6).
3 Press the following to call.
KD-X462BT: Volume knob
KD-X368BT: *ENTER
“NO PRESET” appears if there is no contact stored.
Bluetooth mode settings
1 Press and hold .
2 Perform ‘Select an item (page3 or 4)’ operation to select an
item (see the following table).
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[BT MODE]
[PHONE SELECT]* Selects the phone or audio device to connect or disconnect.
“” appears in front of the device name when connected.
“” appears in front of the current playback audio device.
[AUDIO SELECT]*
[DEVICE DELETE]
1 Perform ‘Select an item (page 3 or 4)’ operation to select a device
to delete.
2 Perform ‘Select an item (page 3 or 4)’ operation to select [YES] or
[NO].
* You can connect a maximum of two Bluetooth phones and one Bluetooth audio device at a time.
JS_JVC_KD_X462BT_M_EN_1.indd 17JS_JVC_KD_X462BT_M_EN_1.indd 17 6/5/2018 11:06:10 AM6/5/2018 11:06:10 AM

18 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
[PIN CODE EDIT]
(0000)
Changes the PIN code (up to 6 digits).
1 Perform the following operation to select a number.
KD-X462BT: Turn the volume knob
KD-X368BT: Press VOL +/–
2 Press S / T to move the entry position.
Repeat steps 1 and 2 until you finish entering the PIN code.
3 Press the following to confirm.
KD-X462BT: Volume knob
KD-X368BT:
* ENTER
[RECONNECT] [ON]: The unit is automatically reconnect when the last connected
Bluetooth device is within the connectable range. ; [OFF]: Cancels.
[AUTO PAIRING] [ON]: The unit is automatically paired with the supported Bluetooth
device (iPhone/iPod touch) when it is connected through USB input
terminal. Depending on the operating system of the connected device, this
function may not work. ; [OFF]: Cancels.
[INITIALIZE] [YES]: Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.). ; [NO]: Cancels.
[INFORMATION] [MYBTNAME]: Displays the name of your receiver (“KD-X4 BT”/
“KD-X3 BT”). ;
[MYADDRESS]: Shows address of this unit.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold .
“BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING
PHONE” “PIN IS 0000” scrolls on the display.
2 Search and select the name of your receiver (“KD-X4 BT”/
“KD-X3 BT”) on the Bluetooth device within 3minutes.
BLUETOOTH®
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same
passkey appears on the unit and Bluetooth device, then operate the
Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is done successfully, “PAIRING OK” “Device Name” appears
and Bluetooth compatibility check starts.
If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to
allow phonebook access to continue.
“TESTING” flashes on the display.
The connectivity result flashes on the display.
“PAIRING OK” and/or “HANDS-FREE OK”*1 and/or “AUD.STREAM OK”*2 and/
or “PBAP OK”*3: Compatible
*1 Compatible with Hands-Free Profile (HFP)
*2 Compatible with Advanced Audio Distribution Profile (A2DP)
*3 Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has
been deleted, and the unit exits check mode.
• To cancel, press and hold source button to turn off the power, then turn
on the power again.
JS_JVC_KD_X462BT_M_EN_1.indd 18JS_JVC_KD_X462BT_M_EN_1.indd 18 6/5/2018 11:06:11 AM6/5/2018 11:06:11 AM

ENGLISH 19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH — Audio
For key layout on the faceplate, see page 3 or page 4.
While in BT AUDIO source, you can connect to five Bluetooth audio devices and
switch between these five devices.
Audio player via Bluetooth
1 Press source button repeatedly to select BTAUDIO (or press SOURCE on the
remote control).
• Pressing enters BT AUDIO directly.
2 Operate the audio player via Bluetooth to start playback.
To On the faceplate On the remote control
Play back/pause KD-X462BT: Press the volume knob.
KD-X368BT: Press *ENTER.
Press d.
Select group or folder Press 2J/ 1K. Press J/ K.
Reverse skip/
Forward skip
Press S/ T. Press H/ I.
Reverse/
Fast-forward
Press and hold S/ T. Press and hold H/ I.
Repeat play Press 4repeatedly.
[TRACKREPEAT], [ALLREPEAT],
[REPEATOFF]
( Not available )
Random play Press 3repeatedly.
[GROUPRANDOM], [ALLRANDOM],
[RANDOMOFF]
( Not available )
Select a file from a
folder/list
Refer to “Select a file from a folder/
list” on page 11. ( Not available )
BLUETOOTH®
To On the faceplate On the remote control
Switch between
connected Bluetooth
audio devices
Press 5.*
( Not available )
* Pressing the “Play” key on the connected device itself also causes switching of sound
output from the device.
Operations and display indications may differ according to their
availability on the connected device.
Settings to use JVC Remote application
JVC Remote application is designed to control the JVC car
receiver’s operations from iPhone/iPod (via Bluetooth or via USB
input terminal) or Android smartphone (via Bluetooth).
Preparation:
• Install the latest version of JVC Remote application on your
device before connecting.
• For more information, visit <http://www.jvc.net/cs/car/>.
1 Press and hold .
2 Perform ‘Select an item (page3 or 4)’ operation to
select an item. (Page20)
3 Repeat step 2 until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_X462BT_M_EN_1.indd 19JS_JVC_KD_X462BT_M_EN_1.indd 19 6/5/2018 11:06:11 AM6/5/2018 11:06:11 AM

20 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Listen to iPhone/iPod via Bluetooth
You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.
Press source button repeatedly to select iPodBT.
• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB
input terminal. (Page 9)
• If you plug in an iPhone/iPod to the USB input terminal while listening to
iPod BT source, the source automatically changes to iPod USB. Press source
button to select iPod BT if the device is still connected via Bluetooth.
Internet radio via Bluetooth
You can listen to internet radio (Spotify) on the iPhone/iPod touch/Android
device via Bluetooth on this unit.
• Make sure the USB input terminal is not connected to any device.
Listen to Spotify
Preparation:
Select
[ON] for [SPOTIFY SRC] in [SOURCE SELECT] . (Page 6)
1 Start up the Spotify application on your device.
2 Connect your device via Bluetooth connection. (Page13)
3 Press source button repeatedly to select SPOTIFY (for iPhone/iPod) or
SPOTIFY BT (for Android device).
The source switches and broadcast starts automatically.
• You can operate Spotify in the same way as Spotify via USB input terminal.
(Page 11)
BLUETOOTH®
Default: [XX]
[REMOTE APP]
[SELECT] Selects the device (IOS or ANDROID) to use the application.
[IOS] [YES]: Selects iPhone/iPod to use the application via Bluetooth or connected via
USB input terminal. ; [NO]: Cancels.
If IOS is selected, select iPod BT source (or iPod USB source if your iPhone/iPod is
connected via USB input terminal) to activate the application.
• The connectivity of the application will be interrupted or disconnected if:
– You change from iPod BT source to any playback source connected via the
USB input terminal.
– You change from iPod USB source to iPod BT source.
[ANDROID] [YES]: Selects Android smartphone to use the application via Bluetooth. ;
[NO]: Cancels.
[ANDROID
LIST]*Selects the Android smartphone to use from the list.
[STATUS] Shows the status of the selected device.
[IOS CONNECTED]: You are able to use the application using the iPhone/iPod
connected via Bluetooth or USB input terminal.
[IOS NOT CONNECTED]: No IOS device is connected to use the application.
[ANDROID CONNECTED]: You are able to use the application using the Android
smartphone connected via Bluetooth.
[ANDROID NOT CONNECTED]: No Android device is connected to use the
application.
* Displayed only when [ANDROID] of [SELECT] is set to [YES].
JS_JVC_KD_X462BT_M_EN_1.indd 20JS_JVC_KD_X462BT_M_EN_1.indd 20 6/5/2018 11:06:12 AM6/5/2018 11:06:12 AM