JVC KD-X120 User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
FRANÇAIS
TÜRKÇE
РУCCKИЙ
B5A-0118-06 [EU]
KD-X120
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE
MANUEL D’INSTRUCTIONS
DİJİTAL MEDYA ALICISI
KULLANIM KILAVUZU
ЦИФРОВОЙ МУЛЬТИМЕДИЙНЫЙ РЕСИВЕР
ИHCTPУKЦИЯ ПO ЭKCПЛУATAЦИИ
Please read all instructions carefully before
operation to obtain the best possible performance
from the unit.
Veuillez lires les instructions attentivement avant
d’utiliser l’appareil afin d’obtenir les meilleures
performances possibles de l’appareil.
Üniteden mümkün olan en iyi performansı
almak için, üniteyi çalıştırmadan önce lütfen tüm
talimatları dikkatli bir şekilde okuyun.
Прежде чем приступать к эксплуатации,
пожалуйста, внимательно прочитайте все
инструкции, чтобы обеспечить оптимальную
работу этого устройства.
JS_JVC_KD_X120_EU_C_06.indd 1JS_JVC_KD_X120_EU_C_06.indd 1 17/9/2014 9:09:17 AM17/9/2014 9:09:17 AM

i
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
For Israel
Дата изготовления (месяц/год) находится на этикетке устройства.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries
(applicable for countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household
waste.
Old electrical and electronic equipment and batteries should be recycled at a facility capable of
handling these items and their waste byproducts.
Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and
waste disposal will help conserve resources whilst preventing detrimental effects on our health and
the environment.
Notice: The sign “Pb” below the symbol for batteries indicates that this battery contains lead.
Information sur l’élimination des anciens équipements électriques et électroniques et piles
électriques (applicable dans les pays qui ont adopté des systèmes de collecte sélective)
Les produits et piles électriques sur lesquels le pictogramme (poubelle barrée) est apposé ne peuvent
pas être éliminés comme ordures ménagères.
Les anciens équipements électriques et électroniques et piles électriques doivent être recyclés sur des
sites capables de traiter ces produits et leurs déchets.
Contactez vos autorités locales pour connaître le site de recyclage le plus proche. Un recyclage adapté
et l’élimination des déchets aideront à conserver les ressources et à nous préserver des leurs effets
nocifs sur notre santé et sur l’environnement.
Remarque: Le symbole “Pb“ ci-dessous sur des piles électrique indique que cette pile contient du plomb.
For Turkey
Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik Elektrikli ve Elektronik Eşyalarin Kontrolü
Yönetmeliğe uygun olarak üretilmiştir.
Eski Elektrik ve Elektronik Ekipmanların İmha Edilmesi Hakkında Bilgi (atık yan ürün
toplama sistemlerini kullanan ülkeleri için uygulanabilir)
Sembollü (üzerinde çarpı işareti olan çöp kutusu) ürünler ev atıkları olarak atılamaz.
Eski elektrik ve elektronik ekipmanlar, bu ürünleri ve ürün atıklarını geri
dönüştürebilecek bir tesiste değerlendirilmelidir. Yaşadığınız bölgeye en yakın
geri dönüşüm tesisinin yerini öğrenmek için yerel makamlara müracaat edin.
Uygun geri dönüşüm ve atık imha yöntemi sağlığımız ve çevremiz üzerindeki
zararlı etkileri önlerken kaynakların korunmasına da yardımcı olacaktır.
JS_JVC_KD_X120_EU_C_06.indd iJS_JVC_KD_X120_EU_C_06.indd i 17/9/2014 9:09:18 AM17/9/2014 9:09:18 AM

ii
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Declaration of Conformity with regard to the EMC Directive 2004/108/EC
Declaration of Conformity with regard to the RoHS Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
EU Representative’s:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany
Déclaration de conformité se rapportant à la directive EMC 2004/108/EC
Déclaration de conformité se rapportant à la directive RoHS 2011/65/EU
Fabricant:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
Représentants dans l’UE:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany
EMC Direktifi 2004/108/EC uyarınca Uygunluk Beyanı
RoHS Yönergesi 2011/65/EU'ya göre Uygunluk Bildirimi
Üretici:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
AB Temsilcisi:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany
Декларация соответствия относительно Директивы EMC 2004/108/EC
Декларация соответствия относительно Директивы RoHS 2011/65/EU
Производитель:
JVC KENWOOD Corporation
3-12 Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
Представительство в ЕС:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been
designed to connect specifically to iPod, or iPhone, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory standards. Please
note that the use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Android is trademark of Google Inc.
libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
- Neither the name of the Xiph.org Foundation nor the names of its contributors may be
used to endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND ONTRIBUTORS “AS IS”
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
JS_JVC_KD_X120_EU_C_06.indd iiJS_JVC_KD_X120_EU_C_06.indd ii 17/9/2014 9:09:18 AM17/9/2014 9:09:18 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
CONTENTS BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short
circuit.
• USB rating is indicated on the main unit. To view, detach the faceplate. (
3 )
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
USB / ANDROID 5
RADIO 6
AUX 8
AUDIO SETTINGS 8
DISPLAY SETTINGS 10
MORE INFORMATION 11
TROUBLESHOOTING 12
SPECIFICATIONS 13
INSTALLATION /
CONNECTION 14
How to read this manual
• Operations are explained mainly using buttons on the faceplate.
• English language is used for the display explanation in this manual.
• [
XX ] indicates the selected items.
• (
XX ) indicates references are available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft
cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector. Connector (on the reverse
side of the faceplate)
JS_JVC_KD_X120_EU_EN_06_3.indd 2JS_JVC_KD_X120_EU_EN_06_3.indd 2 17/9/2014 9:09:30 AM17/9/2014 9:09:30 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power. —
Adjust the volume Turn the volume knob. Press or .
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press repeatedly.
• Press , then turn the volume knob within 2 seconds.
• Press to select USB source directly.
Press SOURCE repeatedly.
Change the display
information
Press repeatedly. (
11 )—
Attach
How to reset
Detach
Your preset adjustments
will also be erased.
Faceplate
Volume knob
(turn/press) Display window
Detach button
Remote control (RM-RK52)
This unit can be remotely controlled with an
optionally purchased remote control.
How to replace the battery
Pull out the insulation
sheet when using for
the first time.
Remote sensor (Do not
expose to bright sunlight.)
JS_JVC_KD_X120_EU_EN_06_3A.indd 3JS_JVC_KD_X120_EU_EN_06_3A.indd 3 18/9/2014 10:42:32 AM18/9/2014 10:42:32 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
1 Press and hold .
2 Turn the volume knob to select [ DEMO ], then press the knob.
3 Turn the volume knob to select [ DEMOOFF ], then press the knob.
4 Press to exit.
Set the clock
1 Press and hold .
2 Turn the volume knob to select [ CLOCK ], then press the knob.
3 Turn the volume knob to select [ CLOCKSET ], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [ 24H/ 12H ], then press the knob.
6 Turn the volume knob to select [ 12 HOUR ] or [ 24 HOUR ], then press the
knob.
7 Press to exit.
To return to the previous setting item, press .
Set the basic settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
1
2
Default: XX
SETTINGS
BEEP ON
:Activates the keypress tone.; OFF :Deactivates.
SRC SELECT
AM
* ON :Enables AM in source selection.; OFF :Disables.
AUX * BTADAPTER :Selects when the KS-BTA100 Bluetooth adapter is
connected to the AUX jack. (
8 ); ON :Enables AUX in source selection.;
OFF :Disables.
F/W UPDATE
SYSTEM
F/W xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
CLOCK
CLOCK SYNC AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio SSData System signal.;
OFF :Cancels.
CLOCK DISP ON :The clock time is shown on the display even when the unit is turned
off.;
OFF :Cancels.
ENGLISH Selected language is use as the display language for menu and Tag
information (folder name, file name, song title, artist name, album name)
if applicable.
By default, the menu language is:
ENGLISH
РУССКИЙ
* Not displayed when the corresponding source is selected.
3
JS_JVC_KD_X120_EU_EN_06_3A.indd 4JS_JVC_KD_X120_EU_EN_06_3A.indd 4 18/9/2014 10:42:34 AM18/9/2014 10:42:34 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
USB / ANDROID
To On the faceplate On the remote control
Reverse / Fast-forward*3Press and hold . Press and hold .
Select a file Press .Press .
Select a folder*4Press . Press .
Repeat play*3Press repeatedly.
TRACK RPT / RPT OFF : JVC Playlist Creator (JPC) / JVC Music
Control (JMC) file (
11 )
TRACK RPT / FOLDER RPT / RPT OFF : MP3/WMA/WAV/FLAC file
ONE RPT / ALL RPT / RPT OFF : ANDROID
Random play*3Press repeatedly.
FOLDERRND / ALL RND / RND OFF : MP3/WMA/WAV/FLAC file or JPC / JMC
file
SONG RND / ALL RND / RND OFF : ANDROID
*1
Do not leave the cable inside the car when not using.
*2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
(
11 )
*3
For ANDROID: Applicable only when [ AUTO MODE ] is selected. ( 6 )
*4
Only for MP3/WMA/WAV/FLAC files. This does not work for ANDROID.
Start playback
The source changes automatically and
playback starts.
USB input terminal
USB 2.0 cable
*1
(commercially available)
Micro USB 2.0 cable
*1
(commercially available)
USB
ANDROID*2
JS_JVC_KD_X120_EU_EN_06_3A.indd 5JS_JVC_KD_X120_EU_EN_06_3A.indd 5 18/9/2014 10:42:35 AM18/9/2014 10:42:35 AM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
To On the faceplate
Select control
mode
While in ANDROID source, press
repeatedly.
AUTO MODE : Control from the unit (using JVC MUSIC
PLAY application).
AUDIO MODE : Control other media player applications
from the Android device (without using
JVC MUSIC PLAY application). However,
you can still play/pause or file skip from
the unit.
Select music
drive
Press repeatedly.
The stored songs in the following start playback.
• Selected internal or external memory of a
smartphone (Mass Storage Class).
• Selected drive of a multiple drives device.
Select a file from a folder/list
1 Press .
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA/WAV/FLAC or JPC / JMC file:
Turn the volume knob quickly.
• To return to the previous setting item, press .
• To cancel, press and hold .
• For ANDROID, applicable only when [
AUTO MODE ] is selected.
(
Select control mode )
USB / ANDROID RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient
signal strength.
Search for a station
1 Press repeatedly to select FM or AM.
2 Press (or press on RM-RK52) to search for a station
automatically.
(or)
Press and hold (or press and hold on RM-RK52) until
“M” flashes, then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the
knob.
The preset number flashes and “MEMORY” appears.
JS_JVC_KD_X120_EU_EN_06_3A.indd 6JS_JVC_KD_X120_EU_EN_06_3A.indd 6 18/9/2014 10:42:36 AM18/9/2014 10:42:36 AM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press
2 Turn the volume knob to select a preset number, then press the
knob to confirm.
Other settings
1 Press and hold .
2 Turn the volume knob to select [ TUNER ], then press the knob.
3 Turn the volume knob to make a selection ( see the following table ) ,
then press the knob.
4 Repeat step 3until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press .
Default:
XX
RADIO TIMER Turns on the radio at a specific time regardless of the current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the timer will be turned
on.
2 FM / AM :Select the source.
3 01 to 18 (for FM)/ 01 to 06 (for AM):Select the preset station.
4 Set the activation day*
1
and time.
“
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [
OFF ] is selected for [ AM ] in [ SRCSELECT ] after Radio Timer for AM is
selected. (
4 )
SSM SSM01–06 / SSM07–12 / SSM13–18 :Automatically presets up to
18 stations for FM. “SSM” stops flashing when the first 6 stations are stored.
Select
SSM07–12 / SSM13–18 to store the following 12 stations.
RADIO
LOCAL SEEK *2 ON :Searches only stations with good reception.; OFF :Cancels.
• Settings made are applicable only to the selected source/station. Once
you change the source/station, you need to make the settings again.
IF BAND AUTO :Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.);
WIDE :Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
MONO ON :Improves the FM reception, but the stereo effect will be lost.;
OFF :Cancels.
NEWS-STBY *2 ON :The unit will temporarily switch to News Programme if available.;
OFF :Cancels.
REGIONAL *2 ON : Switches to another station only in the specific region using the “AF”
control.;
OFF :Cancels.
AF SET *2 ON : Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor.;
OFF : Cancels.
TI SET *2 ON : Allows the unit to temporarily switch to Traffic Information if
available (“TI” lights up). ;
OFF :Cancels.
PTY SEARCH *2 Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
PTY code : NEWS , AFFAIRS , INFO , SPORT , EDUCATE , DRAMA , CULTURE , SCIENCE ,
VARIED , POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),
CLASSICS , OTHER M (music), WEATHER , FINANCE , CHILDREN , SOCIAL , RELIGION ,
PHONE IN , TRAVEL , LEISURE , JAZZ , COUNTRY , NATION M (music), OLDIES , FOLK M
(music),
DOCUMENT
*1
Selectable only when [ ONCE ] or [ WEEKLY ] is selected in step 1 .
*2
Only for FM source.
JS_JVC_KD_X120_EU_EN_06_3.indd 7JS_JVC_KD_X120_EU_EN_06_3.indd 7 17/9/2014 9:09:36 AM17/9/2014 9:09:36 AM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Use a portable audio player
1 Connect a portable audio player (commercially available).
2 Select [ ON ] for [ AUX ] in [ SRC SELECT ]. ( 4 )
3 Press repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
Use a Bluetooth® device
1 Connect the Bluetooth adapter, KS-BTA100 (separately purchased).
2 Register (pair) the Bluetooth device with KS-BTA100.
3 Select [ BT ADAPTER ] for [ AUX ] in [ SRC SELECT ]. ( 4 ).
4 Press repeatedly to select BT AUDIO.
5 Start using the Bluetooth device.
For details, refer to the instruction manual of KS-BTA100.
3.5mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
AUX
Auxiliary input jack
Blue/white Blue/white: Remote
Black Black: Ground
Brown Brown: Tel muting
Wiring harness of the unit
(
15 )
AUDIO SETTINGS
To On the faceplate
Select a preset
equalizer
Press repeatedly.
Press , then turn the volume knob
within 2seconds.
Preset equalizer : FLAT (default), HARD ROCK , JAZZ , POP ,
R&B , TALK , USER1 , USER2 , VOCAL BOOST , BASS BOOST ,
CLASSICAL , DANCE
Store your own
sound settings
1 Press and hold .
2 Turn the volume knob to select [ EASY EQ ], then
press the knob.
3 Turn the volume knob to select [ USER1 ] or
[
USER2 ], then press the knob.
4 Turn the volume knob to make a selection,
then press the knob.
For settings, refer to step 2of [
EASYEQ ]. ( 9 )
• To return to the previous setting item, press .
• To exit, press .
Other settings
1 Press and hold .
2 Turn the volume knob to make a selection ( 9 ), then press the
knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_X120_EU_EN_06_3.indd 8JS_JVC_KD_X120_EU_EN_06_3.indd 8 17/9/2014 9:09:36 AM17/9/2014 9:09:36 AM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Default: XX
EQSETTING
EQPRESET FLAT
/ HARD ROCK / JAZZ / POP / R&B / TALK / USER1 / USER2 /
VOCALBOOST / BASSBOOST / CLASSICAL / DANCE :Selects a preset
equalizer.
EASYEQ 1 USER1 / USER2 :Select a preset name.
2 Adjust your own sound settings.
SUB.W SP
*1*2
: 00 to +06 (Default: 03
SUB.W
*1*3
: –08 to +08 00
BASS  LVL : –06 to +06 00
MID  LVL: –06 to +06 00
TRE  LVL : –06 to +06 00 )
PRO EQ 1 USER1 / USER2 :Select a preset name.
2 BASS / MIDDLE / TREBLE :Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
BASS Frequency: 60 / 80 / 100 / 200HZ
(
Default: 80HZ
Level: –06 to +06 00
Q: Q1.0 / Q1.25 / Q1.5 / Q2.0 Q1.0 )
MIDDLE Frequency: 0.5 / 1.0 / 1.5 / 2.5KHZ (Default: 1.0KHZ
Level: –06 to +06 00
Q: Q0.75 / Q1.0 / Q1.25 Q1.25 )
TREBLE Frequency: 10.0 / 12.5 / 15.0 / 17.5KHZ (Default: 10.0KHZ
Level: –06 to +06 00
Q: QFIX QFIX )
AUDIO
BASS BOOST +01
/ +02 : Selects your preferred bass boost level.; OFF :Cancels.
LOUD 01 / 02 :Boosts low or high frequencies to produce a well-balanced
sound at low volume.;
OFF :Cancels.
SUB.W LEVEL
*1
SPK-OUT
*2
00 to +06 ( +03 ):Adjusts the output level of the
subwoofer connected via speaker lead. (
 15 )
PRE-OUT
*3
–08 to +08 ( 00 ):Adjusts the output level of the
subwoofer connected to the lineout terminals (REAR/
SW) through an external amplifier. (
 15 )
SUB.W
*3
ON / OFF : Turns on or off the subwoofer output.
SUB.W  LPF
*1
THROUGH :All signals are sent to the subwoofer. ; LOW  55HZ /
MID  85HZ / HIGH120HZ :Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.WPHASE
*1
REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [
THROUGH ] is selected for
[
SUB.W  LPF ].)
FADER R06 — F06 ( 00 ):Adjusts the front and rear speaker output balance.
BALANCE
*4
L06 — R06 ( 00 ):Adjusts the left and right speaker output balance.
VOL ADJUST –05 — +05 ( 00 ):Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
*1
Displayed only when [ SUB.W ] is set to [ ON ].
*2
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ]. (  10 )
*3
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ]. (  10 )
*4
This adjustment will not affect the subwoofer output.
AUDIO SETTINGS
JS_JVC_KD_X120_EU_EN_06_3.indd 9JS_JVC_KD_X120_EU_EN_06_3.indd 9 17/9/2014 9:09:36 AM17/9/2014 9:09:36 AM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AMP GAIN LOW  POWER :Limits the maximum volume level to 30.
(Select if the maximum power of each speaker is less than
50W to prevent damaging the speakers.);
HIGHPOWER :The
maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-
frequency components and restoring the rise-time of
the waveform that are lost in audio data compression.;
OFF :Cancels.
TEL  MUTING
*5
ON :Mutes the sounds while using the cellular phone (not
connected through KS-BTA100).;
OFF :Cancels.
SPK/PRE  OUT Selects the appropriate setting to get the desired output. ( See
the following table
.)
*5
Does not work if [ BT  ADAPTER ] is selected for [ AUX ] in [ SRC  SELECT ]. (  4 )
SPK/PRE OUT
Setting Lineout terminal Rear speaker lead
REAR/SW L (left) R (right)
REAR/REAR Rear speakers
output
Rear speakers
output
Rear speakers
output
REAR/SUB.W Subwoofer output Rear speakers
output
Rear speakers
output
SUB.W/SUB.W Subwoofer output Subwoofer output (Mute)
If [ SUB.W/SUB.W ] is selected:
– [
HIGH120HZ ] is selected in [ SUB.W  LPF ] and [ THROUGH ] is not
available.
– [
R01 ] is selected in [ FADER ] and selectable range is [ R06 ]to [ 00 ]
AUDIO SETTINGS
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table), then
press the knob.
3 Repeat step 2until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: XX
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the [ BRIGHTNESS ] setting.
OFF :Selects the day adjustments.; ON :Selects the night adjustments.; DIMMER
TIME
:Adjusts the dimmer on and off time.
Turn the volume knob to adjust the [
ON ] time, then press the knob.
Turn the volume knob to adjust the [
OFF ] time, then press the knob.
(Default: [
ON ]: 18:00 or 6:00 PM
[
OFF ]: 6:00 or 6:00 AM)
AUTO :Changes between the day and night adjustments when you turn off or on the car
headlights.*
1
BRIGHTNESS Sets the button, display and USB input terminal brightness for day and night separately.
1 DAY / NIGHT :Select day or night.
2 Select a zone for setting. ( Illustration above )
3 Set the brightness level ( 00 to 31 ). (Default: BUTTONZONE : DAY : 25 ; NIGHT : 09
DISPZONE : DAY : 31 ; NIGHT : 12 )
SCROLL * 2 ONCE :Scrolls the display information once.; AUTO :Repeats scrolling at 5-second
intervals.;
OFF :Cancels.
[ NIGHTCOLOR ] or [ DAYCOLOR ] is changed by turning on or off your car’s headlight.
*1
The illumination control wire connection is required. ( 15 )
*2
Some characters or symbols will not be shown correctly (or will be blanked).
DISPLAY SETTINGS
JS_JVC_KD_X120_EU_EN_06_3.indd 10JS_JVC_KD_X120_EU_EN_06_3.indd 10 17/9/2014 9:09:37 AM17/9/2014 9:09:37 AM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Playable files
• Playable audio file: MP3 (.mp3), WMA (.wma), WAV(.wav), FLAC (.flac)
• Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
About USB devices
• This unit can play MP3/WMA/WAV/FLAC files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- WAV Tag: 64 characters
- FLAC Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder
without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory
(AOA)2.0.
• If the Android device supports both mass storage class device and AOA2.0, this unit always
playback via AOA2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>.
MORE INFORMATION
About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and Android
TM
application JVC Music
Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music
Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site:
<http://www.jvc.net/cs/car/>.
Available Cyrillic letters
Change the display information
Press repeatedly.
FM or AM Station name (PS)*
1
Frequency Program type (PTY)*
1
*
2
Title*
1
*
2
Day/Clock (back to the beginning)
*1
For FM Radio Data System stations only.
*2
If unavailable, “NO PTY” / “NO TEXT” appears.
USB Playing time Day/Clock Album title/Artist*
3
Track title*
3
Folder/file name (back to the beginning)
*3
If not recorded, “NO NAME” appears.
USB-ANDROID Playing time Day/Clock Album title/Artist*
4
Track title*
4
(back to the beginning)
*4
If not recorded, “NO NAME” appears.
AUX AUX Day/Clock
BT AUDIO BT AUDIO Day/Clock
Available characters
Display indications
JS_JVC_KD_X120_EU_EN_06_3.indd 11JS_JVC_KD_X120_EU_EN_06_3.indd 11 17/9/2014 9:09:37 AM17/9/2014 9:09:37 AM

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Symptom Remedy
General
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
Turn the power off, then check to be sure the terminals
of the speaker wires are insulated properly. Turn the
power on again.
“PROTECTING SEND
SERVICE” appears.
Send the unit to the nearest service center.
Source cannot be selected. Check the [
SRCSELECT ] setting. ( 4 )
Radio
• Radio reception is poor.
• Static noise while listening
to the radio.
• Connect the antenna firmly.
• Pull the antenna out all the way.
USB
Playback order is not as
intended.
The playback order is determined by the file name
(USB).
Elapsed playing time is not
correct.
This depends on the recording process earlier.
“NOT SUPPORT” appears and
file skips.
Check whether the file is a playable format. (
11 )
“READING” keeps flashing. • Do not use too many hierarchical levels and folders.
• Reattach the USB device.
“CANNOT PLAY” flashes and/
or connected device cannot
be detected.
• Check whether the connected device is compatible with
this unit and ensure the files are in supported formats.
( 11)
• Reattach the device.
Correct characters are not
displayed.
This unit can only display uppercase letters, numbers,
and a limited number of symbols. Uppercase Cyrillic
letters can also be displayed if [
РУССКИЙ ] is selected.
(
4 )
TROUBLESHOOTING
Symptom Remedy
ANDROID
• Sound cannot be heard
during playback.
• Sound output only
from the Android
device.
• Reconnect the Android device.
• If in [
AUDIO MODE ], launch any media player application
on the Android device and start playback.
• If in [
AUDIO MODE ], relaunch the current media player
application or use another media player application.
• Restart the Android device.
• If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit. (
11 )
Cannot playback at
[
AUTO MODE ].
• Make sure JVC MUSIC PLAY APP is installed on the Android
device. ( 5 )
• Reconnect the Android device and select the appropriate
control mode. (
6 )
• If this does not solve the problem, the connected Android
device does not support [
AUTO MODE ]. ( 11 )
“NO DEVICE” or
“READING” keeps
flashing.
• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android
device does not support [
AUTO MODE ]. ( 11 )
Playback is intermittent
or sound skips.
Turn off the power saving mode on the Android device.
“CANNOT PLAY” • Make sure Android device contains playable audio files.
• Reconnect the Android device.
• Restart the Android device.
If you still have troubles, reset the unit. ( 3)
JS_JVC_KD_X120_EU_EN_06_3.indd 12JS_JVC_KD_X120_EU_EN_06_3.indd 12 17/9/2014 9:09:38 AM17/9/2014 9:09:38 AM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SPECIFICATIONS
Tuner
FM Frequency Range 87.5MHz — 108.0MHz (50kHz step)
Usable Sensitivity (S/N=26dB) 0.71μV/75Ω
Quieting Sensitivity
(DINS/N=46dB)
2.0μV/75Ω
Frequency Response (±3dB) 30Hz — 15kHz
Signal-to-Noise Ratio (MONO) 64dB
Stereo Separation (1kHz) 40dB
AM Frequency Range MW 531kHz — 1611kHz (9kHz step)
LW 153kHz — 279kHz (9kHz step)
Usable Sensitivity (S/N=20dB) MW 28.2μV
LW 50μV
USB
USB Standard USB1.1, USB2.0 (Full speed)
Compatible Devices Mass storage class
File System FAT12/16/32
Maximum Supply Current DC5V 1A
D/A Converter 24 Bit
Frequency Response (±1dB) 20Hz — 20kHz
Signal-to-Noise Ratio (1kHz) 105dB
Dynamic Range 88dB
Channel Separation 90dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
WAV Decode RIFF waveform Audio Format (Linear PCM only)
FLAC Decode FLAC files
Auxiliary

Frequency Response (±3dB) 20Hz—20kHz
Input Maximum Voltage 1000mV
Input Impedance 30kΩ
Audio
Maximum Output Power 50W×4 or
50W×2 + 50W×1 (Subwoofer = 4Ω)
Full Bandwidth Power
(at less than 1% THD)
22W×4
Speaker Impedance 4Ω—8Ω
Preout Level/Load (USB) 2500mV/10kΩ
Preout Impedance ≤600Ω
General
Operating Voltage
(10.5V—16V allowable)
14.4V
Maximum Current Consumption 10A
Operating Temperature Range 0°C to +40°C
Installation Size (W×H×D) 182mm×53mm×108mm
Weight 0.58k
g
Subject to change without notice.
JS_JVC_KD_X120_EU_EN_06_3.indd 13JS_JVC_KD_X120_EU_EN_06_3.indd 13 17/9/2014 9:09:38 AM17/9/2014 9:09:38 AM

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Warning
• The unit can only be used with a 12V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50W. If the
maximum power of the speakers is lower than 50W, change the
[AMPGAIN] setting to avoid damaging the speakers. (  10 )
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then
disconnect the terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( 
15 )
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Reset the unit. (  3 )
INSTALLATION / CONNECTION
How to remove the unit
Bracket (not supplied)
Pocket
Flat or round head screws
(not supplied) M5 × 8mm
Do the required wiring.
(  15)
Bend the appropriate tabs to
hold the sleeve firmly in place.
Hook on the top side
Orientate the trim plate as
illustrated before fitting. Dashboard of
your car
Installing the unit (in-dash mounting)
When installing without the mounting
sleeve
Use only the specified screws. Using wrong screws
might damage the unit.
JS_JVC_KD_X120_EU_EN_06_3.indd 14JS_JVC_KD_X120_EU_EN_06_3.indd 14 17/9/2014 9:09:38 AM17/9/2014 9:09:38 AM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Part list for
installation
(A) Faceplate
(C) Mounting sleeve
(B) Trim plate
(D) Wiring harness
(E) Extraction key
STEERING
WHEEL
REMOTE
Wiring connection
Car fuse block
Ignition switch
Recommended
connection
Vehicle-specific Wiring
Harness (separately
purchased)
For more information:
Metra Electronics:
www.metraonline.com
Scosche Industries:
www.scosche.com
Blue/white: To amplifier
Blue: To power antenna
Make this connection if
your vehicle factory wiring
harness does not have
“12V ignition switch” wire.
Separate red wire
Signal cord (not supplied)
Remote wire
(not supplied)
Fuse (10A) Antenna terminalRear/subwoofer output
Factory wiring
harness (vehicle)
Vehicle dashboard
Black: Ground
Yellow: Battery 12V
White: Front speaker (left)
White/black
Gray: Front speaker (right)
Gray/black
Green: Rear speaker (left)
* 2
Green/black * 2
Purple: Rear speaker (right)
Purple/black
Join the same color wires together.
Red: Ignition 12V
Orange/white: Illumination
Brown: Tel muting
Blue/white: Remote (200mA max.)
Light blue/yellow To the steering wheel
remote control adapter
*2
You can also connect a
subwoofer speaker directly
using this lead without an
external subwoofer amplifier.
For setting, 
10 .
JVCAmplifier
* 1
*1
Firmly connect the ground wire of the amplifier to the
car’s chassis to avoid damaging the unit.
JS_JVC_KD_X120_EU_EN_06_3.indd 15JS_JVC_KD_X120_EU_EN_06_3.indd 15 17/9/2014 9:09:39 AM17/9/2014 9:09:39 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
TABLE DES MATIERES AVANT L’UTILISATION
Avertissement
N’utilisez aucune fonction qui risque de vous distraire de la conduite sure de votre véhicule.
Précautions
Réglage du volume:
• Ajustez le volume de façon à pouvoir entendre les sons extérieurs à la voiture afin d’éviter tout risque d’accident.
• Réduisez le volume avant de reproduire des sources numériques afin d’éviter d’endommager les enceintes par la soudaine
augmentation du niveau de sortie.
Généralités:
• Éviter d’utiliser le périphérique extérieur s’il peut gêner une conduite en toute sécurité.
• Assurez-vous que toutes les données importantes ont été sauvegardées. Nous ne pouvons pas être tenu responsable pour
toute perte des données enregistrées.
• Veuillez faire en sorte de ne jamais mettre ou laisser d’objets métalliques (tels que des pièces ou des outils) dans l’appareil, afin
d’éviter tout risque de court-circuit.
• La classe USB est indiquée sur l’appareil principal. Pour le voir, détachez la façade. (
3 )
Télécommande (RM-RK52):
• Ne laissez pas la télécommande dans des endroits exposés à la chaleur, comme sur le tableau de bord par exemple.
• La pile au lithium risque d’exploser si elle est remplacée incorrectement. Ne la remplacez uniquement qu’avec le même type de
pile ou son équivalent.
• Le boîtier de la pile ou les piles ne doivent pas être exposés à des chaleurs excessives telles que les rayons du soleil, du feu, etc.
• Gardez la pile hors de la portée des enfants et dans son emballage d’origine quand elle n’est pas utilisée. Débarrassez-vous des
piles usagées rapidement. En cas d’ingestion, contactez un médecin immédiatement.
AVANT L’UTILISATION 2
FONCTIONNEMENT DE BASE 3
PRISE EN MAIN 4
USB / ANDROID 5
RADIO 6
AUX 8
RÉGLAGES AUDIO 8
RÉGLAGES D’AFFICHAGE 10
PLUS D’INFORMATIONS 11
GUIDE DE DÉPANNAGE 12
SPÉCIFICATIONS 13
INSTALLATION /
RACCORDEMENT 14
Comment lire ce manuel
• Les opérations sont expliquées principalement en utilisant les touches de la façade.
• La langue anglaise est utilisée pour l’explication des affichages de ce manuel.
• [
XX ] indique les éléments choisis.
• (
XX ) indique que des références sont disponibles aux page citées.
Entretien
Nettoyage de l’appareil: Essuyez la saleté de la façade avec un chiffon sec au silicone ou
un chiffon doux.
Nettoyage du connecteur: Détachez la façade et nettoyez le connecteur à l’aide d’un
coton tige en faisant attention de ne pas endommager le connecteur. Connecteur (sur la face arrière
de la façade)
JS_JVC_KD_X120_EU_FR.indd 2JS_JVC_KD_X120_EU_FR.indd 2 15-Oct-14 11:15:48 AM15-Oct-14 11:15:48 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
FRANÇAIS
FONCTIONNEMENT DE BASE
Pour Sur la façade Sur la télécommande
Mettez l’appareil sous tension Appuyez sur .
• Maintenez la touche enfoncée pour mettre l’appareil hors tension.
—
Ajustez le volume Tournez le bouton de volume. Appuyez sur ou .
Appuyez sur le bouton de volume pour couper le son ou mettre la lecture en
pause.
• Appuyez une nouvelle fois pour annuler.
Appuyez sur pour couper le son ou mettre la lecture
en pause.
• Appuyez une nouvelle fois pour annuler.
Sélectionner la source • Appuyez répétitivement sur .
• Appuyez sur , puis tournez le bouton de volume avant 2 secondes.
• Appuyez sur pour sélectionner directement la source USB.
Appuyez répétitivement sur
SOURCE .
Changez l’information sur
l’affichage Appuyez répétitivement sur . (
11 )
—
Attachez
Comment réinitialiser
Détachez
Vos ajustements préréglés
sont aussi effacés.
Façade
Bouton de volume
(tournez/appuyez) Fenêtre d’affichage
Touche de détachement
Télécommande (RM-RK52)
Cet appareil peut être commandé à distance avec une
télécommande vendue séparément.
Comment remplacer la pile
Retirez la feuille d’isolant
lors de la première
utilisation.
Capteur de télécommande (Ne l’exposez
Pas à la lumière directe du soleil.)
JS_JVC_KD_X120_EU_FR.indd 3JS_JVC_KD_X120_EU_FR.indd 3 15-Oct-14 11:15:51 AM15-Oct-14 11:15:51 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
PRISE EN MAIN
Annulez la démonstration
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour choisir [ DEMO ], puis appuyez sur le bouton.
3 Tournez le bouton de volume pour choisir [ DEMO OFF ], puis appuyez sur le
bouton.
4 Appuyez sur pour quitter.
Réglez l’horloge
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour choisir [ CLOCK ], puis appuyez sur le bouton.
3 Tournez le bouton de volume pour choisir [ CLOCK SET ], puis appuyez sur le
bouton.
4 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le bouton.
Jour Heure Minute
5 Tournez le bouton de volume pour choisir [ 24H/ 12H ], puis appuyez sur le bouton.
6 Tournez le bouton de volume pour choisir [ 12 HOUR ] ou [ 24 HOUR ], puis appuyez
sur le bouton.
7 Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur .
Faites les réglages de base
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour réaliser une sélection (voir le tableau
suivant), puis appuyez sur le bouton.
3 Répétez l’étape 2jusqu’à ce que l’élément souhaité soit sélectionné ou activé.
4 Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur .
1
2
Défaut: XX
SETTINGS
BEEP ON
:Met en service la tonalité des touches.; OFF :Met hors service la
fonction.
SRC SELECT
AM
* ON :Met en service AM dans la sélection de la source.; OFF :Hors service.
AUX * BT ADAPTER :Sélectionne ce réglage quand l’adaptateur Bluetooth
KS-BTA100 est connecté à la prise AUX. (
8 ); ON :Met en service AUX dans
la sélection de la source.;
OFF :Hors service.
F/W UPDATE
SYSTEM
F/W xxxx YES
:Démarrer la mise à niveau du micrologiciel.; NO :Annulation (la mise à
niveau n’est pas activée).
Pour en savoir plus sur la mise à niveau du micrologiciel, référez-vous à:
<http://www.jvc.net/cs/car/>.
CLOCK
CLOCK SYNC AUTO
:L’horloge est réglée automatiquement à l’aide des données d’horloge
(CT) comprises dans les données du signal FM Radio SSData System.;
OFF :Annulation.
CLOCK DISP ON :L’horloge apparaît sur l’affichage même quand l’appareil est hors
tension.;
OFF :Annulation.
ENGLISH
La langue sélectionnée est utilisée comme langue d’affichage pour les menus
et les informations de la balise (nom de dossier, nom de fichier, titre du
morceau, nom de l’artiste, nom de l’album) le cas échéant.
Par défaut la langue des menus est:
ENGLISH
РУССКИЙ
* Pas d’affichage quand la source correspondante est sélectionnée.
3
JS_JVC_KD_X120_EU_FR.indd 4JS_JVC_KD_X120_EU_FR.indd 4 15-Oct-14 11:15:54 AM15-Oct-14 11:15:54 AM