JVC NX-D2 User manual

Warnings, Cautions and Others
Mises en garde, précautions et indications diverses
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur ni le coffret de l’appareil. Il n’y a aucune pièce réparable par l’utilisateur à
l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION: Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas regarder directement dans le
faisceau avec des instruments optiques.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.
1
42
3
GVT0277-007A[J]
1209WMKMDWJMM
©2009 Victor Company of Japan, Limited
INSTRUCTIONS
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Le symbole de l’éclair à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur
la présence d’une “tension dangereuse” non
isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution de
personnes.
Le point d’exclamation à l’intérieur d’un
triangle équilatéral est destiné à alerter
l’utilisateur sur la présence d’opérations
d’entretien importantes au sujet desquelles des
renseignements se trouvent dans le manuel
d’instructions.
For U.S.A.
Caution: Changes or modifications not expressly
approved by party responsible for compliance could void
the user’s authority to operate the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Pour les Etats-Unis
Attention : Les changements ou les modifications
qui ne sont pas explicitement approuvés par la partie
responsable de l’observance pourraient mettre fin au droit
de l’utilisateur d’utiliser le matériel.
Remarque : Cet appareil a été testé et il s’est avéré
conforme aux limites applicables à un appareil numérique
de classe B, en vertu de la Partie 15 des Règles de la
FCC. Ces limites sont conçues de manière à assurer
une protection raisonnable contre les interférences
nuisibles dans une installation résidentielle. Cet appareil
produit, utilise et peut émettre une énergie de haute
fréquence et, s’il n’est pas installé et utilisé en conformité
avec les instructions, il peut causer des interférences
nuisibles aux communications radio. Il n’y a, toutefois,
aucune garantie que des interférences ne se produiront
pas dans une installation particulière. Si cet appareil
cause effectivement des interférences nuisibles à la
réception de la radio ou de la télévision, ce qu’on peut
établir en mettant l’appareil en marche et à l’arrêt,
nous encourageons l’utilisateur à tenter de corriger
l’interférence par une ou plusieurs des mesures suivantes :
– réorienter ou déplacer l’antenne de réception ;
– accroître la séparation entre l’appareil et le récepteur ;
– brancher l’appareil dans une prise ou un circuit autre
que celui auquel le récepteur est branché ;
– consulter un vendeur ou un technicien radio/TV
expérimenté pour obtenir de l’aide.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO
NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
AVERTISSEMENT:
POUR PRÉVENIR LES RISQUES D’INCENDIE OU
DE CHOCS ÉLECTRIQUES, NE PAS EXPOSER CE
APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
CAUTION
The button in any position does not disconnect the mains line.
Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights red.
• When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION
La touche , dans n’importe quelle position, ne déconnecte pas le système du secteur.Déconnectez la fiche de secteur
pour mettre l’appareil complètement hors tension (le témoin STANDBY s’éteint).
La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion de l’appareil, et l’appareil déconnecté doit
être prêt à être utilisé.
• Quand le système est en attente, le témoin STANDBY est allumé en rouge.
• Quand le système est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être télécommandée.
CAUTION
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
ATTENTION
Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du soleil, feu, etc.).
[European Union only]
[Union européenne seulement]
CAUTION
• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth,
etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
ATTENTION
• Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au rebut des piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un égouttement ou à des éclaboussures et ne placez pas des objets
remplis de liquide, tels qu’un vase, sur l’appareil.
CAUTION:
Excessive sound pressure from earphones or headphones can cause hearing loss.
ATTENTION:
Une pression acoustique excessive des écouteurs ou du casque d’écoute peut entraîner une perte auditive.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10
cm (3-15/16”) or more.
ATTENTION: Aération correcte
Pour prévenir tout risque de décharge électrique ou d'incendie et éviter toute détérioration, installez l'appareil de la manière
suivante:
1. Avant: Bien dégagé de tout objet.
2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-dessous.
3. Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation correcte puisse se faire en le
plaçant sur un support d’au moins dix centimètres de hauter.
Main unit
Front
Face
Side
Côté
SpeakerSpeaker Main unit
GVT0277-007A
For Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED
“DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
Pour le Canada
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR;
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
GVT0277-007A EN_NX-D2[J] Starting up
GVT0277-007A EN_NX-D2[J] Starting up
GVT0277-007A EN_NX-D2[J] Starting up
GVT0277-007A EN_NX-D2[J] Starting up
IntroductionPrecautions
Playable Disc/File Types
• CD-R/-RW: Recorded in the Audio CD format. MP3,
WMA files written in accordance with the “ISO 9660”
format can also be played.
• USB device: MP3, WMA files.
In addition to the above discs/files, this System can play
back audio data recorded on CD-Extra and CD-G (CD-
Graphics).
• The following discs cannot be played back:
CD-I (CD-I Ready), and Photo CD.
Playing back these discs will generate noise and damage
the speakers.
• CD Text can be played, but text information will not be
shown on the display.
Notes on the power cord
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always
pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or
moving the System.
• Do not alter, twist or pull the power cord, or put anything
heavy on it, which may cause fire, electric shock, or other
accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
Avoid moisture, water, dust, and high
temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult your
dealer. Using the System in this state may cause a fire or
electrical shock.
• Do not expose the System to direct sunlight or place it near
a heating device.
7License and Trademark
• iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• “Made for iPod” means that an electronic accessory has
been designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance
standards.
• Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Notes on installation
• Select a place which is level, dry and neither too hot nor too
cold—between 5˚C and 35˚C (41°F and 95°F).
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
• Do not drag or push the speakers on the floor or table;
otherwise, the four feet at the bottom side of each speaker
may peel off or drop from the speaker.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
ENGLISH
COMPACT COMPONENT SYSTEM
NX-D2
Thank you for purchasing a JVC product.
Before operation, please read the instructions
carefully.
For customer use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or
side of the cabinet. Retain this information for
future reference.
Model No.
Serial No.
NX-D2 INSTRUCTIONS—Starting up
— Consists of CA-NXD2 and SP-NXD3
EN_NX-D2[J].indb 1 10.1.7 4:27:57 PM

5
6
7
8
GVT0277-007A EN_NX-D2[J] Starting up
GVT0277-007A EN_NX-D2[J] Starting up
GVT0277-007A EN_NX-D2[J] Starting up
GVT0277-007A EN_NX-D2[J] Starting up
Basic Operations
Troubleshooting
Amplifier section
Output Power: 115 W per channel, min. RMS, driven into
3  at 1 kHz with no more than 10% total
harmonic distortion
Audio Input:
AUDIO IN: Stereo mini ( φ 3.5 mm)
500 mV/47 kΩ(at “AUDIO LVL3”)
250 mV/47 kΩ(at “AUDIO LVL2”)
125 mV/47 kΩ(at “AUDIO LVL1”)
USB PLAY (input)
VIDEO OUT (iPod):
Color system:
NTSC (interlaced)
VIDEO (Composite):
1 V(p-p)/75 Ω
Speaker impedance:
3 Ω– 16 Ω
Tuner section
FM tuning range: 87.5 MHz – 108.0 MHz
AM tuning range: 530 kHz – 1 710 kHz
Disc player section
Dynamic range: 80 dB
Horizontal resolution: 500 lines
Wow and flutter: Immeasurable
iPod section
Power supply: DC 5 V 500 mA (each iPod dock)
USB section
USB specification: Compatible with USB 2.0 Full Speed
Compatible device: Mass storage class
Compatible system: FAT16, FAT32
Output power: DC 5 V 500 mA
General
Power requirements:
AC 120 V , 60 Hz
Power consumption:
90 W (at operation)/
1.00 W or less (at standby)
Dimensions (approx.):
195 mm × 333 mm × 313 mm
(7-11/16 inches × 13-1/8 inches × 12-3/8
inches) (W × H × D)
Mass (approx.): 3.6 kg (8 lbs)
Speaker System—SP-NXD3
Type: 3-way 3-speaker Bass Reflex Type
(Magnetically-Shielded Type)
Speaker units:
Tweeter: 2.0 cm (13/16 inch) dome × 1
Mid Range: 5.0 cm (2 inch) cone × 1
Woofer: 16.0 cm (6-5/16 inches) cone × 1
Impedance: 3 Ω
Power handling capacity:
115 W
Frequency range:
40 Hz – 20 000 Hz
Sound pressure level:
84 dB/W•m
Dimensions: 205 mm × 409.5 mm × 290.5 mm
(8-1/8 inches × 16-1/8 inches × 11-7/16
inches) (W × H × D)
Mass: 3.6 kg (8 lbs) each
Connections
Using the number buttons and cursor buttons on
the remote control
Preparing the remote control
Insert the batteries into the remote control by matching the
polarity (+ and –) correctly.
If the range or effectiveness of the remote control decreases,
replace both batteries.
Caution:
Be careful your children do not put the batteries into their
mouths.
How to cancel the demonstration
Press and hold ECO/DEMO button on the main unit (until
“DEMO CLEAR” appears on the display) while on standby.
• When the ECO Mode is activated, the demonstration
does not work.
• Refer to the attached sheet “Information about the
demonstration function.”
• In this manual, operations using the remote control
are mainly explained; however, you can use the buttons
and controls on the main unit if they have the same (or
similar) name and marks.
• Button and control operations are explained in the table
below.
Indicates that you press the button.
2 sec. Indicates that you press and hold the
button for a specified period.
Indicates that you slide your finger
on the volume jog in the specified
direction(s).
For private listening
Connect a pair of headphones to the PHONES jack on
the main unit. The sound will no longer come out of the
speakers. “HPHONE IN” appears on the display for a while.
Be sure to turn down the volume before connecting or
putting on the headphones.
• Disconnecting the headphones will activate the speakers
again.
• When using the headphones with the L-shaped plug,
connect it with the head of the plug facing the right side
as illustrated below.
DO NOT turn off the System with the volume set at an
extremely high level; otherwise, the sudden blast of sound
may damage your hearing, speakers and/or headphones
when you turn on the System or start playback.
Changing the Display Brightness
You can dim the display and illumination lamp. Setting
DIMMER allows you to reduce power consumption.
DIMMER 1 Dims the display and the blue illumination
on the main unit.
DIMMER 2 Dims the display more than DIMMER 1
and turns off the blue illumination on the
main unit.
DIMMER OFF Normal brightness.
Setting the ECO (Ecology) Mode
Setting the ECO Mode allows you to reduce power
consumption by turning the display off while on standby.
While the System is on standby...
On the main unit On the remote
To cancel, repeat the procedure.
Turning Off the Power Automatically
Auto Standby
• This does not function while “FM,” “AM” or “AUDIO IN” is
selected as the source.
To cancel, press the button again.
Sleep Timer
1Specify the time (in minutes).
2Wait until the set time disappears.
To check the time remaining until the shut-off time, press
SLEEP once.
To change the display information
• The information displayed and its order vary among the source.
On the main unit On the remote
AUDIO IN:
Current source information =Clock
TUNER AM or FM:
Frequency =Clock
CD:
Current source information =Group name, file name and tag information (for MP3, WMA) =Disc or file type (while
stopped) =Clock
USB:
Current source information =Group name, file name and tag information (for MP3, WMA) =Disc or file type (while
stopped) =Clock
iPod:
Current source information =Tag information (artist name, album name, track name)*1=Clock
*1 Tag information cannot be displayed for some iPod models (refer to “Enjoying Movies/Music from your iPod” in “Operating
Guide”).
Changing the pattern of the level meter
You can select the appearance of the level meter from 5
patterns (“LVL MTR 1” – “LVL MTR 5”).
Turning On/Off the Power
On the main unit On the remote
• Selecting a source (see below) while in standby mode also
turns on the System.
Selecting the Source
On the main unit
(Touch to select)
On the remote
Adjusting the Volume
On the main unit On the remote
Volume +: Slide your finger
clockwise.
Volume –: Slide your finger
counterclockwise.
To drop the volume in a moment
To restore the volume, press again or adjust the volume
level.
Do not connect the power cord until all other connections have been made.
1
3
2
4
567
8
9
p
q
w
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• FM antenna (×1)
• AM loop antenna (×1)
• Composite video cord (×1)
• Remote control; RM-SNXD2J (×1)
• Batteries (×2)
If any items are missing, consult your dealer immediately.
Speakers
When connecting the speaker cords, match the polarity
of the speaker terminals: red to (+) and black to (–)
TV/monitor
• Connect your TV directly to the System. Connecting
the System to a TV via other device, such as a VCR
or an HDD/DVD recorder, may interfere with your
viewing. Connecting an integrated TV/VCR system to
the System may also interfere with your viewing.
AM/FM antenna
To assemble the AM loop antenna
Keep the AM loop antenna cable wrapped around the
AM loop antenna frame, otherwise the effectiveness and
sensitivity of the AM loop antenna may be reduced.
For better FM reception, disconnect the supplied FM
antenna, and connect to an outdoor FM antenna using a
75 Ω wire with coaxial type connector (not supplied).
To the wall outlet
1USB indicator
2iPod indicator
3Playback mode indicators
• PRGM (Program) indicator
• RND (Random) indicator
• Repeat Mode indicators
/
4FM reception indicators
5Level meter
6Sound Mode indicators
• S.MODE (Sound Mode) indicator
• (Surround) indicator
7V. BASS (Vario Bass) indicator
8Karaoke operation indicators
• (Mic Mixing) indicator
• (Echo) indicator
9Timer indicators
pA.STBY (Auto Standby) indicator
qSLEEP indicator
wMain display
(canceled)
Remote sensor
STANDBY lamp
Turns off: The System is turned on.
Lights in red: The System is on standby.
Headphones
PHONES jack
When using the remote control
Point the top of the remote control towards the remote
sensor as directly as possible. If you operate it from a
diagonal position, the operating range (about 5 m and/or 16
feet) may be shorter. Motion Sensor
When you move your hand close to the remote sensor in the
following cases, the illumination on the front panel turns on.
• While the System is on standby.
• When “DIMMER 1” or “DIMMER 2” is selected.
To activate or deactivate the motion sensor, press
MOTION SENSOR.
• When the motion sensor is activated, “SELECT SOURCE”
appears on the display while on standby.
• When the motion sensor is deactivated, the clock is shown
on the display while on standby.
• When the ECO Mode is activated, the motion sensor does
not work.
Number buttons
Press to enter numbers.
Example:
• To select number 5, press
5.
• To select number 10,
press 10.
• To select number 15,
press 10, 1, then 5.
• To select number 30,
press 10, 3, then 0.
• To select number 125,
press 10, 10, 1, 2, then
5.
Cursor buttons
Press to select an item.
Touch panel
To get the best performance of the System, keep your discs
clean.
Handling Discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, extreme temperature,
and moisture.
To clean the disc
Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it forcefully.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in
contact for a long time.
General
Adjustments or settings are suddenly canceled before
you finish.
]There is a time limit. Repeat procedure again.
Operations are disabled.
]The built-in microprocessor may malfunction due to
external electrical interference. Unplug the power cord
and then plug it back in.
Unable to operate the System from the remote control.
]The path between the remote control and the remote
sensor on the System is blocked.
]The batteries are exhausted.
No sound is heard.
]Speaker connections are incorrect or loose.
]Headphones are connected.
No picture appears on the TV screen.
]The video cord connections are incorrect or loose.
iPod Device Playback Operations
Content on an iPod cannot be played back even
though “CONNECT” is displayed in the display window.
]The battery of the iPod is running low.
The iPod cannot be controlled from this unit.
]The iPod is not compatible with this unit.
Disc/USB Device Playback Operations
The disc does not play.
]The disc is placed upside down. Place the disc with the
label side facing up.
ID3 Tag on an MP3 file cannot be shown.
]Two types of ID3 Tag exist—Version 1 and Version 2.
This System can only show ID3 Tag Version 1.
Tracks are not played back as you expect.
]The playing order is determined when the groups
and tracks were recorded. It depends on the writing
application.
MP3, WMA files are not played back.
]The disc or the USB device may contain different types of
files (ex. MP3/WMA/WAV/JPEG).
The disc sound is discontinuous.
]The disc is scratched or dirty.
The disc tray does not open or close.
]The power cord is not plugged in.
]Child Lock is in use. “LOCKED” appears on the display
(refer to “Listening to a Disc/USB Device” in “Operating
Guide”).
Radio Operations
Hard to hear broadcasts because of noise.
]Antenna connections are incorrect or loose.
]The AM loop antenna is too close to the System.
]The FM antenna is not properly extended and positioned.
Timer Operations
Daily Timer does not work.
]The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
Maintenance
Preparations
Specifications
Display Indicators
FM antenna (supplied)
Extend it so that you can obtain the
best reception.
AM loop antenna
(supplied)
Turn it until the best
reception is obtained.
From the
right speaker
From the
left speaker
Composite video cord (supplied)
Yellow
Black
Black
Red
Red
EN_NX-D2[J].indb 2 10.1.7 4:28:00 PM

GVT0277-017B
9
10
11
12
GVT0277-017B EN_NX-D2[J] Operating Guide 02
GVT0277-017B EN_NX-D2[J] Operating Guide 02
GVT0277-017B EN_NX-D2[J] Operating Guide 02
GVT0277-017B EN_NX-D2[J] Operating Guide 02
To insert a disc
• When using an 8 cm disc, place it on the inner circle of the
disc tray.
To close the disc tray, press 0again.
To prohibit disc ejection (Child Lock)
When the System is turned on and the disc tray is closed,
press 0while touching 7(on the main unit).
To cancel the prohibition, repeat the same procedure.
“UNLOCKED” appears on the display.
To connect a USB device
Listening to a Disc/USB Device
To select a group
While playing...
To select a track/file
While playing...
• When you press 4for the first time, you go back to the
beginning of the current track/file.
To locate a particular position
While playing...
To locate an item directly
To select a group:
Press a group number using the number buttons.
To select a track/file:
Press a track/file number using the number buttons.
USB cable (not supplied)
Resume Play
The System can store the stop point, and when you start
playback again by pressing CD 6or USB 6(even
while on standby), it starts from the position where you
have stopped—Resume Play.
To stop completely while Resume is activated, press 7
twice.
Unique File Operations
The operations will vary depending on the discs or files.
To select the audio track
Or press number buttons to select the audio track.
You can select the audio channel to listen to.
Display Message
NO DEVICE, NO USB
• No USB device is connected or the connected USB device
is not compatible with this System.
DEVICE ERR
• The unit has failed to read the USB device.
CAN’T PLAY
• Playable format file does not exist in USB device.
Canceled
NX-D2 INSTRUCTIONS—Operating Guide
To connect an audio player
You can listen to the audio player connected to the AUDIO
IN jack.
• Make sure to turn down the volume on the System to
minimum level before starting playback.
To adjust the audio input level
If the sound from the device connected to the AUDIO IN jack
is too loud or too quiet, you can preset the audio input level
through the AUDIO IN jack (without changing the volume
level).
While “AUDIO IN” is selected as the source...
• As the number of the level increases, the preset input level
is increased.
Listening to the Radio Listening to an External Device
Tuning in to a Station
While FM or AM is selected...
Frequency starts changing on the display. When a station
(frequency) with sufficient signal strength is tuned in, the
frequency stops changing.
• When you repeatedly press the button, the frequency
changes step by step. To manually stop the search, press
either button.
• The ST indicator lights while an FM stereo station with
sufficient signal strength is tuned in.
If the FM reception is poor
The MONO (monaural) indicator lights on the display.
Reception will improve though stereo effect is lost—
Monaural reception.
To restore the stereo effect, press the button again. The
MONO (monaural) indicator disappears.
Stereo mini plug (not supplied)
From audio output
(or headphone out, etc.)
Enjoying Movies/Music from your iPod
Compatible iPod Models To connect an iPod
Connect an iPod to dock A or B on the unit. You can have 2
iPod devices connected at the same time.
• Make sure the unit is on standby when you connect the
iPod.
• When you connect iPod to the dock, make sure the
terminal on the dock is fully inserted into iPod.
• After connecting iPod, wait until the unit is ready for
operation (about 3 seconds).
• Be careful not to damage the terminal on the dock when
connecting / disconnecting the iPod.
• Do not touch or hit the terminals of the dock and of iPod.
It might cause damage to these terminals.
• Always set the volume to the minimum level when
connecting or disconnecting iPod.
• Do not carry the unit with iPod connected. You might drop
it down or it might cause damage to the connector part.
• Remove iPod from the dock when you do not use it.
To detatch the dock adapter from the dock:
Pull up the dock adapter with your fingernail or sharp
pointed tool using the slot.
• Be careful not to injure your fingertips or damage the
terminal of the dock.
About charging the battery of iPod
The unit enables users to charge the battery of iPod.
1Press to turn on the power of the unit.
2Select iPod as the source.
3Press and hold 7for 2 seconds to start charging.
• Press and hold 7to deactivate the battery charging
fuction.
• When 2 iPod devices are connected, both batteries are
charged at the same time.
• For details of the battery charging, see the instruction
manual for iPod.
Playing Back iPod Devices
• Before viewing a video/picture from iPod on your
TV, make the appropriate video setting on iPod. For
details of the setting, see the instruction manual for
iPod.
• For iPod touch
Operate iPod touch itself in the following cases:
–when operating the home button
–when selecting application icons on the home screen
–when dragging the slider
• When you cannot operate iPod connected through
the unit or using the remote control, operate iPod
itself.
To start / To pause
To forward or reverse skip
While playing…
To fast-forward or fast-reverse the track
While playing…
Dock adapter (supplied with the iPod or
sold separately)
Dock A Dock B
Shuffle Play
Applies Shuffle Play to iPod A or iPod B selected as the
source. Select the desired shuffle mode.
• The shuffle icon lights up on the display of iPod devices.
• To cancel, press again until the shuffle icon disappears.
iPod model Audio
Video
Tag
information
Composite
iPod nano
1GB/2GB/4GB ✓—✓
iPod nano (2nd generation)
2GB/4GB/8GB ✓—✓
iPod nano (3rd generation)
4GB/8GB ✓✓ ✓
iPod nano (4th Generation)
8GB/16GB ✓✓ ✓
iPod mini
4GB ✓——
iPod mini (2nd Generation)
4GB/6GB ✓——
iPod with color display
20GB/60GB ✓——
iPod (Click Wheel)
20GB/40GB ✓——
iPod classic
80GB/120GB/160GB ✓✓ ✓
iPod photo
30GB/40GB/60GB ✓✓*1—
iPod (5th Generation)
30GB/60GB/80GB ✓✓ ✓
iPod touch
8GB/16GB/32GB ✓✓ ✓
iPod touch (2nd Generation)
8GB/16GB/32GB ✓✓*2✓
*1 Only for still picture.
*2To view a video/picture from iPod touch on your TV, update the software to the latest version. (Any additional
charges may apply.) For details about updating iPod, check on the Apple web site <http://www.apple.com>.
Playing Back
To start / To pause
To stop
Program Play/Random Play
• Program Play/Random Play cannot be used for USB.
Ex:
To exit Program Play or Random Play, press PROGRAM
or RANDOM until PRGM, RND are all off before or after
playback.
PROGRAM—To program the playing order.
• You can arrange the playing order of the tracks/files (up to
99) before you start playback.
• Resume does not work for Program Play.
1Press PROGRAM button.
2Select tracks/files you want for Program Play using
the number buttons.
• For MP3/WMA files:
Select a group number, then select a track/file
number.
3Repeat step 2until you complete your program.
4Press 6to start playback.
RANDOM—To play all the tracks at random.
Playing Repeatedly
Press REPEAT repeatedly to select Repeat Mode.
• Repeat Mode varies depending on the medias or the files.
REPEAT TRK Repeats the current track/file.
REPEAT ALL Repeats all the contents of tracks/files.
REPEAT GRP Repeats the current group.
REPEAT OFF Canceled.
(PROGRAM mode)
REPEAT STEP Repeats the current track/file.
REPEAT ALL Repeats all the programmed tracks/files.
REPEAT OFF Canceled.
Canceled
Presetting the Stations
You can preset 30 FM and 15 AM stations.
1Tune in to a station you want to preset.
• You can also store the monaural reception mode for
FM preset stations if it has been selected.
2Press SET to activate the preset number entry
mode.
• Finish the following process while the indication on
the display is flashing.
3Select a preset number for the station you store
using the number buttons.
4Press SET to store the station.
To tune in to a preset station
1Select the band (FM or AM).
2Select the preset number using the number
buttons.
To back up a preset station
Press to go back to the standby mode. This memorizes
the preset station you set.
2 sec.
Timer Operations
Setting the Daily Timer
1Select DAILY (1 – 3) time setting mode (ON)
2Set the timer as you like.
Repeat the procedure for the following settings until
finished.
1Set the hour then the minute for on-time.
2Set the hour then the minute for off-time.
3Select the playback source—“TUNER AM,” “DISC,”
“USB,” “iPod A,” “iPod B,” “AUDIO IN” or “TUNER
FM.”
4For “TUNER AM” or “TUNER FM”: Select a preset
channel.
For “DISC”: Select the group number, then the track/
file number*.
For “USB”: Select the group number, then the track/
file number*.
* You can select up to 99 groups and 150 tracks/files.
5Select the volume level (“MIN” to “MAX” and “– –”).
If you select “– –,” the volume is set to the same level
as when the System was last turned off.
Once settings are completed, the timer setting
information appears in sequence.
3Turn off the System (on standby), if you have set
the timer with the System turned on.
To cancel the Daily Timer, select DAILY (1 – 3) you want to
cancel, then press CANCEL.
To turn on the Daily Timer, select DAILY (1 – 3) you want
to turn on, then press ENTER/SET.
Setting the Clock
Without setting the built-in clock, you cannot use Daily
Timer.
1Press CLOCK/TIMER.
• If you have already adjusted the clock before, press
the button repeatedly until the clock setting mode is
selected (see below).
2Adjust the hour, then the minute using the cursor
buttons, press SET.
• To exit the clock settings, press CLOCK/TIMER as
required.
• To return to the previous step, press CANCEL.
Clock setting
Daily Timer
DAILY1 =ON (Time)
Canceled
Daily Timer
DAILY2 =ON (Time)
Daily Timer
DAILY3 =ON (Time)
(Press and hold)
Repeat play back
Press REPEAT to change the repeat playback settings. Press
once for track repeat, twice for repeat all, and once more to
cancel. The System displays “REPEAT” only (the icon on the
iPod display changes).
• Refer to the instruction manual for the iPod for details.
To go back to the previous menu
To select an item on the menu
• To confirm an item on the menu, press “SET.”
A B Shuffle
This function enables two iPod devices to play in shuffle
mode alternately. You can play a variety of songs from both
iPod devices. When the track of the current iPod source
finishes, a track from the other iPod source will be played
automatically and this cycle repeats.
1Connect iPod to docks A and B on the unit.
• Compatible iPod models are the same as those
compatible with Tag information. Refer to “Compatible
iPod Models” on page 9.
2With both iPod devices connected, press the
SHUFFLE button twice. The unit displays “A ← −
→ B ON” and will start playing a track.
• The iPod indicator (refer to “Display Indicators” in
“Starting up”) on the unit is displayed and the current
iPod source icon blinks while playing.
3To stop A B Shuffle, press the SHUFFLE button
again. The unit displays “A ← − → B OFF” and will
stop playing the track.
• Removing one of the iPod devices from the dock will
also stop A B Shuffle.
• If this function does not work correctly, reconnect the iPod
devices regardless of whether “CONNECTED” is displayed
on the unit.
(Press and hold)
Canceled
ENGLISH
EN_NX-D2[J].indb 3 10.1.7 4:28:04 PM

13
14
15
16
GVT0277-017B EN_NX-D2[J] Operating Guide 02
GVT0277-017B EN_NX-D2[J] Operating Guide 02
GVT0277-017B EN_NX-D2[J] Operating Guide 02
GVT0277-017B EN_NX-D2[J] Operating Guide 02
Enjoying Karaoke
IMPORTANT
• Always set MIC LEVEL to “MIN” (0) before disconnecting
the microphone.
• MIC LEVEL adjustment is valid for both microphones
connected to the MIC 1 and MIC 2 jacks.
• If the microphone does not work properly, please
disconnect it and connect again.
Singing Along (Karaoke)
1Connect the microphone(s) (not supplied) to the
MIC 1 and/or MIC 2 jack.
2Start playing a source.
3Sing into the microphone.
4Adjust the microphone level and volume.
On the main unit On the remote
Changing the Karaoke Setting
ECHO—To apply an echo to your voice.
• You can adjust the echo level from ECHO OFF (no effect)
to ECHO 6 (strongest).
MIC VOL—To change the mic volume.
• The mic volume level can be adjusted in 16 steps from
MIN (0) to MAX (15).
DO NOT keep the microphones connected while they are
not in use.
Sound Adjustments
Adjusting the Sound
Various Bass Effect—To create a sound suitable for the
playback source.
On the main unit On the remote
LITEnEASY Suitable for Karaoke and classical music. You
can obtain a comfortable bass sound.
MOVIE Suitable for a video source and playback of
external component. You can obtain a strong
bass sound.
TECHNO Suitable for disco or techno music. You can
obtain a strong bouncy bass sound.
TURBO Suitable for most kinds of music and
playback of external component. You can
obtain a balanced bass sound.
AUTO The System automatically applies TURBO,
LITEnEASY, MOVIE or TECHNO
according to the playback source (initial
setting).
OFF No sound effect.
Superbass level adjustment—From level 1 to level 5.
On the main unit
On the remote
Selecting the Sound Modes
Sound Mode (for CD, USB and iPod)—To select
one of the preset Sound Modes.
ROCK Boosts low and high frequency. Good for
acoustic music (initial setting).
POP Good for music with an emphasis on vocal.
CLASSIC Good for classical music.
DANCE Increases resonance and bass.
HALL Adds depth and brilliance to the sound.
STADIUM Adds clarity and spreads the sound, as in an
outdoor stadium.
USER1/2/3 Your individual mode stored in memory.
See below.
FLAT Canceled.
To create your own sound modes (User Mode)
1Select one of the preset Sound Modes.
2Press SET.
3Press 4to select BASS (bass) or TRE (treble) to
adjust.
4Press UP or DOWN to adjust the parameters
then press ENTER/SET.
5Press ¢to select one of the user modes
(USER1–3) to store your setting into.
6Press SET to finish.
Learning More about This System
Connections
• Make sure the antenna conductors do not touch any other
terminals, connecting cords or the power cord. Also, keep
the antennas away from metallic parts of the System,
connecting cords, and the power cord. These could cause
poor reception.
• Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the
System.
• The speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly,
it may cause color distortions. So, pay attention to the
following when installing the speakers.
– When placing the speakers near a TV set, turn off the
TV’s main power switch or unplug it before installing
the speakers.
Then wait at least 30 minutes before turning on the TV’s
main power switch again.
– Some TVs may still be affected even though you have
followed the above instructions. If this happens, move
the speakers away from the TV.
• You cannot connect a computer and JVC Everio
camcorder to the USB terminals of the System.
• Electrostatic shock at connecting a USB device may cause
abnormal playback of the device. In this case, disconnect
the USB device then turn off this unit.
Basic Operations
Setting the ECO (Ecology) Mode:
• If you turn on the Daily Timer while the ECO mode is
activated, the ECO mode is canceled.
Listening to a Disc/USB Device
JVC bears no responsibility for any loss of data in the
USB mass storage class device while using this System.
• When connecting with a USB cable, use the USB 2.0 cable
whose length is less than 1 m.
• You can connect a USB device such as a USB flash memory
device, hard disk drive, multimedia card reader, etc. to this
System.
• When you change the source to “CD” or “USB,” it may take
a while to activate the source.
• While the System is reading a disc, the source may not
change to “USB” properly. Press 7to stop the disc before
changing the source to “USB.”
• On some discs, the actual operations may be different from
what is explained in this manual due to the programming
and disc structure; such differences are not a malfunction
of this System.
• The total number of tracks (files) that the System can detect
is 4 000.
• The System recognizes up to...
– 999 tracks (files) per group.
– 99 groups per disc.
Unplayable files are also counted in the total file number.
Playable files which do not belong to any groups are
recognized as files of group 1.
Program Play/Random Play:
• Program is cleared in the following cases:
– When the System is turned off (standby).
• During programming steps...
– Your entry will be ignored if you have tried to program
an item number that does not exist (for example,
selecting track 14 on a disc that only has 12 tracks).
– For MP3/WMA files, you can program up to 99 files.
– You cannot select the 151st or later tracks.
Listening to the Radio
• If you store a new station into an occupied preset number,
the previously stored station in that number will be erased.
• When you unplug the power cord accidentally or if a power
failure occurs, the preset stations may be erased. If this
happens, preset the stations again.
Timer Operations
General:
• When the System is on standby, you cannot set the clock
and Daily Timer.
Setting the Clock:
• “0:00” will flash on the display until you set the clock.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, reset the clock.
Setting the Daily Timer:
• If you do not specify the preset station or track number
correctly while setting a timer, the currently selected station
or the first track will be played when the timer is activated.
• When you unplug the power cord or if a power failure
occurs, the timer will be canceled. You need to set the clock
first, then the timer again.
• If you set the Sleep Timer after Daily Timer starts playing
the selected source, Daily Timer is canceled.
Sound Adjustments
Adjusting the Sound:
• This function also affects the sound through the
headphones.
Enjoying Movies/Music from your iPod
JVC is not responsible for any loss of or damage to iPod
that might result from the use of this product.
• Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
• Sound distortion may occur when playing back audio
sources with a high recording level. When distortion
occurs, it is recommended to turn off the equalizer
of iPod. For information on operating iPod, see the
instruction manual for iPod.
• If iPod does not play correctly, update iPod software to the
latest version.
• For details about updating iPod, check on the Apple web
site <http://www.apple.com>.
• JVC does not assure the compatibility of iPod released
after April 2009 with this unit.
EN_NX-D2[J].indb 4 10.1.7 4:28:06 PM