JWA FORFAR 5 DRW TALLBOY 70460 User manual

1
ASSEMBLY INSTRUCTION
ITEM CODE 70460
FORFAR 5 DRW TALLBOY
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
1300MM
800MM
480MM

Allow 30 min For 2 person Addional tools required
2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over ghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucons for future reference.

3
PARTS LIST
A
25pcs
B
49pcs
C
20pcs
M8X30mm M3.5X14mmM14.8X12mmM7X39mm
M5X40mm M3X16mm
D
E F
CR DL
G
CL
25pcs
5pcs
18pcs
5pcs
60pcs
5pcs 5pcs
1
2
3
4
5
7
8
6
12
13
14
15
9
10
11
DR
1pcs
M4x30mm M3.5x14mm
H
24pcs
M7X50mm
11
2
13
3
4
5
6
6
6
6
7
7
8
10
12
14
15
13
9
SIDE PANEL
SIDE PANEL
SKIRTS
BOTTOM PANEL
SUPPORT PANEL
SUPPORT PANEL
BACK PANEL
TOP PANEL
DRAWER SIDE PANEL
DRAWER SIDE PANEL
DRAWER BACK PANEL
DRAWER BASE
DRAWER SUPPORT PANEL
DRAWER FRONT
FILLER

4
STEP 1:
STEP 2:
2
D
D
D
D
D
D
D
D
DD
1
CL
D
1
H
H
H
H
H H
H
H
H
H
H 2H
CR
D

5
STEP 3:
STEP 4:
2
3
3
4
56
6
66
CB
B
B
B
C
BC
C
3
3
4
CC

6
STEP 5:
STEP 6:
2
1
3
3
4
56
6
66
C
C
C
B
B
BB
8
H
H
H H

7
STEP 7:
8
2
C
C
B
B
B

8
STEP 8:
STEP 9:
× 5
E
E
E
10
10
13
9
12
11
11
7
15
7
8
2
7
7
15
F
F
F
F
F

9
STEP 10:
STEP 11:
× 5
14
A
A
B
B
B
10
13
14
12
D
DR
D
× 5
D
D
DL
DR
10
14

10
STEP 12:
ASSEMBLY COMPLETE
14
14
14
14
14

11
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
HARDWARE
Wall
Back side
Large Screw x 2Wall Strap x 1Mounting Plate x 2 Small Screw x 2
x 2
G

12
To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void