JWA ALCOY 68425 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
ALCOY
ITEM CODE 68425
DESK

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2
Allow 45 min For 2 person Additional tools required

PARTS LIST
1Desktop panel
2Left side panel
3Right side panel
4Middle panel
5Back panel
6Back panel
7Left side panel
8Right side panel
9Drawer left side panel
10 Drawer right side
panel
11 Drawer left side panel
12 Drawer right side
panel
13 Drawer back panel
14 Drawer bottom panel
P1 Main metal frame
P2 Connection pipe
P3 Back panel paster
P4 Paster
3

4

Load fitting J into the bottom of metal frame P1.
STEP 1:
Press the plastic clasp in the fitting E2 and disassemble E1
and E2.
STEP 2:
5

Use fitting F to fix E1 on the orifice position of panel 2 and
panel 3 respectively.
STEP 3:
Fix E1 on the front and back side of panel 4 with fitting F.
STEP 4:
6

Fix panel 2, 3, 4 and panel 5 on panel 1 with fittings A and D,
pay attention to the direction of the panel.
STEP 5:
Pass through the matching hole of panel 5 with fitting C, and fix
panel 2, 3 and 4 on panel 5.
STEP 6:
7

Fix the metal frame P1 on panel 1 with fitting B, and fix the
metal frame P1 on panel 5 with fitting C.
STEP 7:
Pass through the metal frame P1 with fitting B, fix the metal
pipe P2 on panel 2 and panel 3, and fix the middle part on
the bottom of panel 4 with fitting C.
STEP 8:
P2
8

Connect panel 7, 8 and 6 with fitting A.
STEP 9:
Fix the assembled panel components of 6, 7, 8 on panel
with fitting A.
STEP 10:
9

Use fitting F to fix metal plates G1 and P3 of accessories on
the positioning guide hole of panel6, and finally cover with G2
decorative cover.
STEP 11:
1) Fix panel 11 and panel 12 on panel 13 with fitting C;
2) The wood grain of panel 14 shall be faced up, and
corresponding slots of panel 11 and panel 12 shall be loaded;
3) Fix panels 9 and 10 to panels 11 and 12 with fitting A.
STEP 12:
10

Fix E2 on panel 11 and panel 12 with fitting F.
STEP 13:
Load the assembled drawer 9 assembly and drawer 10
assembly into the corresponding position of the main body.
STEP 14:
11

Load fittings H and I into corresponding parts respectively.
Install a fall preventer.
STEP 15:
ASSEMBLY IS COMPLETE
12

SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
13

To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
14