K-Edge K13-050 User manual

K-EDGE BRAZE-ON CLAMP ADAPTER (SOLD SEPERATELY - K13-030-34.9)
K-EDGE BRAZE-ON ADAPTER
"BACK-BOLT"
1x M5 x 12mm FHCS
"NON-DRIVE / INSIDE" CAGE HALF
"LOCKING-BOLTS"
2x M4 x 12mm SHCS
"DRIVESIDE / OUTSIDE" CAGE HALF
"CAGE-BOLTS"
3x M2.5 x 12mm SHCS
K13-050 - K-EDGE CX SINGLE-RING GUIDE W/ O.L.S.- TECHNICAL INSTRUCTIONS
DESCRIPTION OF PARTS
OR
0.45 N-m (+/- 0.09 N-m)
EQUALLY TORQUE
TO 2.00 N-m (+/- 0.20 N-m)
4.00 N-m (+/- 0.50 N-m)
+5°
-5°
A
A
DESCRIPTION OF O.L.S. - 'OPPOSING-LOCK-SYSTEM'
OPENING FOR 3mm HEX
TOOL ACCESSIBILITY
B
SECTION A-A
VIEW OF MECHANISM
DETAIL B
OF MECHANISM
"BACK-BOLT" SETS
HORIZONTAL DISTANCE FOR
CHAINLINE ALIGNMENT
"LOCKING-BOLTS" PRODUCE AN
'OPPOSING' FORCE ONTO THE BACK-BOLT
- LOCKING THE CAGE INTO DESIRED
POSITION
K-EDGE BRAZE-ON CLAMP ADAPTER
M5 FLAT WASHER
M5 x
20mm
SHCS
IF YOUR FRAME
DOES NOT
HAVE A BRAZE-ON,
USE SETUP BELOW
K-EDGE RADIUS WASHER
M5 FLAT WASHER
M5 x
20mm
SHCS
MOUNTING OPTIONS
IF YOUR FRAME
DOES
HAVE A BRAZE-ON,
USE SETUP BELOW
K-EDGE BRAZE-ON
ADAPTER
BACK-BOLT
APPLY BLUE
LOCTITE ON
THREADS
d
(BOTTOM VIEW)
d
K-EDGE BRAZE-ON
ADAPTER
INNER CAGE
LOCKING-BOLTS
*APPLY BLUE LOCTITE*
** LIGHTLY TIGHTEN **
(a)
DETAIL (a)
** ATTENTION **
ENSURE NO CONTACT
BETWEEN THE
ADAPTER AND FRAME
(b)
DETAIL (b)
** ATTENTION **
ENSURE NO CONTACT
BETWEEN THE
ADAPTER AND FRAME
BRAZE-ON RECOMMENDATIONS:
38T - 42T > UPPER MOUNTING HOLE •
42T - 46T > LOWER MOUNTING HOLE •
UPPER
MOUNTING HOLE
LOWER
MOUNTING HOLE
2.1
DETAIL 2.1
SCALE 1 : 2
ANGLE CAGE TO NEUTRAL
(0-DEGREE) POSITION
1
SET "BACK-BOLT" DISTANCE
MOUNT TO BE USED:
K-EDGE BRAZE-ON CLAMP ADAPTER -
d = 2.9mm •
BRAZE-ON ON FRAME -
d = 4.9mm •
2
INSTALL NON-DRIVE CAGE
AND SET INITIAL ANGLE
INSTALLATION STEPS: 1 > 2 > 3
(a)
OR
(b)
>
OPTION (a)
INCLUDED
OPTION (b)
SOLD SEPERATELY
3(a) 3(b)
INSTALL ONTO FRAME PER
YOUR "MOUNTING OPTION"
(TRUE BRAZE-ON SHOWN)
INSTALL ONTO FRAME PER
YOUR "MOUNTING OPTION"
(CLAMP ADAPTER SHOWN)
OR
PROCEED TO NEXT PAGE FOR
SETUP AND ADJUSTMENT
NOTE:
K-EDGE BRAZE-ON ADAPTER
M5 MOUNTING HOLES
THE K-EDGE BRAZE-ON
ADAPTER HAS 2x M5 MOUNTING
HOLES AVAILABLE FOR
VARIABLE CHAIN RING SIZES.
DEPENDING ON YOUR
CONFIGURATION, YOU MAY
NEED TO USE EITHER THE
UPPER OR LOWER MOUNTING
HOLE.
CLAMP RECOMMENDATIONS:
ALL SIZES USE LOWER MOUNTING HOLE •
DEPENDENT ON FRAME DESIGNS •
REQUIRED TOOLS:
2mm HEX KEY ('L' OR 'T' SHAPE) •
3mm HEX KEY ('L' OR 'T' SHAPE) •
4mm HEX KEY ('L' OR 'T' SHAPE) •
**IF THERE IS
FRAME CONTACT, CONTACT K-EDGE IMMEDIATELY** **IF THERE IS FRAME CONTACT, CONTACT K-EDGE IMMEDIATELY**
THE ABOVE DISTANCES ARE RECOMMENDATIONS TO SAVE YOU
TIME DURING THE ADJUSTMENT STEPS. IF THESE DISTANCES
ARE NOT CORRECT, PLEASE MAKE NOTE AND NOTIFY K-EDGE.

5.1
DETAIL 5.1
4.1
DETAIL 4.1
CURVATURE AT
BOTTOM OF CAGE
RADIUS OF RING
6.1
d
d
DETAIL 6.1
INNER CAGE FACE
OUTER CAGE FACE
CHAIN RING
(CHAIN NOT SHOWN)
DRIVESIDE / OUTER
CAGE
3x M2.5 x 12mm SHCS
*APPLY BLUE LOCTITE*
0.88 N-m (+/- 0.09 N-m)
4.2
DETAIL 4.2
ENSURE THESE TWO FACES
ON INNER CAGE ARE 'IN-LINE'
WITH TEETH OF CHAINRING
7.1
7.2
AFTER ADJUSTMENT IS COMPLETE, EQUALLY
TORQUE 'LOCKING-BOLTS' TO 2.00 N-m (+/-
0.20 N-m), AND CONFIRM ALIGNMENT
+5°
-5°
DETAIL 7.1
ENSURE BOTTOM OF
CAGE IS FLUSH WITH
BOTTOM OF CHAIN
ENSURE REAR OF CAGE
ASSEMBLY IS 0.5-1.0mm
FROM TOP OF CHAIN
RING TEETH
+3°
-3°
DETAIL 7.2
EQUAL DISTANCE
BETWEEN CHAIN
AND CAGE FACES
NO CONTACT
BETWEEN CHAIN
AND CAGE FACES
38T w/ BRAZE-ON CLAMP ADAPTER SHOWN
46T w/ TRUE BRAZE-ON SHOWN
SETUP AND ADJUSTMENT: 4 > 5 > 6 > 7 > 8
5
INSTALL OUTER CAGE
4
ADJUST FOR HEIGHT
ADJUST FOR CHAINLINE DISTANCE
6
CHECK FOR FUNCTION AND BOLT TORQUE
8
ADJUST FOR PITCH AND YAW
7
SET THE HEIGHT OF THE ADAPTER:
'APPROXIMATELY' ALIGN THE CURVATURE AT BOTTOM OF 1.
THE CAGE TO THE RADIUS OF THE RING (SEE DIAGRAM 4.1)
SET 'APPROXIMATE' TOP-DOWN ALIGNMENT OF CAGE TO 2.
THE CHAIN RING (SEE DIAGRAM 4.2)
FINAL ADJUSTMENTS WILL BE MADE AT STEPS #6 - #7
ADJUST FOR CHAINLINE:
SET LATERAL ADJUSTMENT VIA THE COMBINATION OF THE 1.
'LOCKING-BOLTS' AND' BACK-BOLT'
ENSURE EQUAL SPACING BETWEEN THE CHAIN AND THE 2.
INSIDE OF THE INBOARD / OUTBOARD CAGE FACES. (SEE
DIAGRAM 6.1)
d = DISTANCE BETWEEN CAGE FACE AND CHAIN / CHAIN-RING
ADJUST FOR PITCH:
SET PITCH ANGLE VIA THE COMBINATION OF THE 'LOCKING- 1.
BOLTS' AND' BACK-BOLT' MOVEMENT
(MAX ANGLE = +/- 5 )
CONFIRM BOTTOM OF CAGE ASSEMBLY IS FLUSH WITH •
THE BOTTOM OF THE CHAIN. (SEE DIAGRAM 7.1)
CONFIRM REAR OF CAGE ASSEMBLY IS 0.5-1.0mm FROM •
TOP OF CHAIN RING TEETH. (SEE DIAGRAM 7.1)
ADJUST FOR YAW:
SET YAW ANGLE VIA THE COMBINATION OF THE 'LOCKING- 2.
BOLTS' AND' BACK-BOLT' MOVEMENT
( MAX ANGLE = +/- 3
)
CONFIRM FRONT OF CAGE ASSEMBLY IS EQUIDISTANT •
FROM CHAIN AND CAGE FACES. (SEE DIAGRAM 7.2)
CONFIRM REAR OF CAGE ASSEMBLY IS NOT CONTACTING •
CHAIN. (SEE DIAGRAM 7.2)
**IF APPLICABLE, INSTALL CHAIN PRIOR TO CAGE INSTALL**
STEPS TO CHECK FOR FUNCTION AND INSTALLATION INTEGRITY:
SHIFT TO BOTH ENDS OF THE CASSETTE AND CONFIRM NO CONTACT BETWEEN CHAIN AND THE CAGE 1.
IF THERE IS CONTACT •
CONFIRM STEPS #5-#7 •
IF THERE IS NO CONTACT •
PROCEED TO NEXT STEP •
** CAUTION ** DERAILING TO THE OUTSIDE CAN/WILL DAMAGE THE FINISH OF THE CRANKSET - USE WITH DISCRETION
BACK-PEDAL AND MANUALLY DERAIL THE CHAIN FROM THE BOTTOM - TO THE INSIDE AND/OR **OUTSIDE** OF THE RING 2.
IF CHAIN SNAGS AND PREVENTS MOVEMENT OF THE CRANKSET •
CHECK FOR HEIGHT (STEP #4) •
CHECK FOR PITCH (STEP #7.1) •
IF CHAIN IS 'LIFTED' ABOVE THE TEETH AND ALLOWS BACK-PEDALING OF THE CRANKSET •
PROCEED TO NEXT STEP •
PEDAL FORWARD TO 'RE-ENGAGE THE' CHAIN ONTO THE CHAIN RING 3.
IF CHAIN SLIPS BETWEEN THE CAGE AND THE CHAIN RING •
CONFIRM STEPS #6-#7 •
IF CHAIN RE-ENGAGES ONTO CHAIN RING AND FORWARD MOVEMENT IS RESTORED •
PROCEED TO NEXT STEP •
RE-CHECK THE FOLLOWING: 4.
-CAGE PITCH ANGLE
-CAGE YAW ANGLE
-REAR CAGE DISTANCE TO TOP OF TEETH
IF MOVEMENT WAS DETECTED (i.e. NO LONGER IN PROPER ADJUSTMENT) •
REPEAT STEPS #4-#7 •
RE-TORQUE ALL BOLTS IN THE SYSTEM REPEAT FUNCTION TEST •
IF NO MOVEMENT IS DETECTED •
FUNCTION CHECK IS COMPLETE. •
BOLT TORQUE SPECIFICATIONS:
CLAMP MOUNTING BOLT = 2.00 N-m (+/- 0.20 N-m) •
BRAZE-ON MOUNTING BOLT = 4.00 N-m (+/- 0.50 N-m) •
BACK-BOLT = N/A •
LOCKING-BOLTS = 2.00 N-m (+/- 0.20 N-m) •
DRIVESIDE CAGE BOLTS (M2.5 SHCS) = 0.45 N-m (+/- 0.09 N-m) •
K-EDGE CX SINGLE-RING CHAIN GUIDE SPECIFICATIONS:
CHAIN RING SIZE CAPACITY = 38T - 46T •
CHAINLINE DISTANCE = 45.5mm (+/- 2.50mm) •
BRAZE-ON MOUNTING BOLT DISTANCE TO BB-AXIS = 133mm (+/-10mm) •
CHAIN = 11SPD •
NARROW-WIDE CHAIN RING COMPATIBILITY = YES •
DESIGN FEATURES:
FEATURES OF THE K-EDGE CX SINGLE-RING CHAIN GUIDE:
MAXIMUM ADJUSTABILITY TO FIT VARYING FRAME GEOMETRY •
MINIMAL CONTACT DURING NORMAL OPERATION •
MINIMAL WEIGHT GAIN •
ENHANCED 'TOP-SIDE' CHAIN GUIDANCE •
ENHANCED 'TOP-OF-CHAIN CLEARANCE' TO ACCOUNT FOR F.O.D. (FOREIGN OBJECT DEBRIS) •
ENHANCED MUD-CLEARANCE •
ENHANCED ' BACK-PEDAL DERAILMENT PROTECTION' •
EASE OF INSTALLATION AND ADJUSTMENT •
SLIM, SLEEK, AND APPEALING DESIGN •
K13-050 - K-EDGE CX SINGLE RING GUIDE W/ O.L.S.- TECHNICAL INSTRUCTIONS
SUPPORT / CONTACT:
IF PROBLEM(S) STILL PERSIST AFTER TROUBLESHOOTING,
PLEASE CONTACT K-EDGE SUPPORT FOR FURTHER
ASSISTANCE AT [email protected] IMMEDIATELY. PLEASE
BE SURE TO INCLUDE YOUR FULL NAME, PHONE NUMBER,
AND K-EDGE PRODUCT PURCHASED.