Kaiser Baas Rapid Charge 15K User manual

Rapid Charge 15K
Charge your phone,
tablet or USB device
QUICK START

Safety Precautions
Before using the Rapid Charge 15k, please ensure
you read and understand all the safety precau-
tions below.
Keep the Rapid Charge 15k away from water
and other liquids. Do not use the Rapid Charge
15k with wet hands as this may cause the unit to
malfunction.
Keep the Rapid Charge 15k away from direct
sunlight and heat sources.
The Rapid Charge 15k may become slightly warm
during use. This does not indicate a malfunction.
Do not place heavy objects on the Rapid Charge
15k, as this may cause the unit to malfunction.
Do not attempt to open the case or modify the
Rapid Charge 15k in any way, as this will void
your warranty.
Maintenance and repairs should only be per-
formed by Kaiser Baas.
Do not dispose of the unit via conventional
domestic waste.
Your device may become warm while charging.
Specifications
Capacity: 15000mAh
Output: 5v/2500mA
Input: 5V/2000mA
Dimensions: 138x62x21mm
Charging Time: 9 hours (Using 1A AC Adapter)
Operation Temperature: -5°C ~ +55°C
Cycle Life: 500 Cycles

Product Diagram
12 x USB Outputs
2Micro USB Input Port
3LED Charge Indicator
4Switch ON/OFF
Charge Indicator
5One LED On - Power <25%
6Two LED On - Power 25 -50%
7Three LED On - Power 50 - 75%
8Four LED On - Power 75-100%
5 6 7 8
1
3 4
To p
Front
LED Indicator
2

Using the Rapid Charge 11k
Please charge the Rapid Charge 11k to full capac-
ity before your first use.
To charge your digital
device
Connect the output port 1of your Rapid
Charge 11k to your device via a USB cable.
Press the On/O switch one time to start charg-
ing your device.
The LED Indicators should turn on.
Tip: Refer to the previous page for information on the
charge status
When charging a device you can toggle the
LED Indicators by press the On/O Switch. You
cannot turn o the Rapid Charge 11k whilst it is
charging.
If the LED Indicators are o and the Rapid
Charge 11k is charging your device is in Sleep
Mode.
To stop charging simply disconnect your device
from the power source. The Rapid Charge 11k will
automatically cut output within 1 minute.
Please note only a Micro USB to USB cable is
supplied.

Charging the Rapid Charge
15k
The Rapid Charge 15k has 2 methods to re-
charge:
Recommended Method:
Connect the Rapid Charge 15k via the Micro USB
Input Port to a 1A AC Wall Adapter with USB
(Please note this is not supplied).
Alternative Method:
Connect the Rapid Charge 15k via the Micro USB
Input Port to a USB Port on a PC or laptop.
When recharging the four LED indicators will
flash one by one.
Pressing the On/O Switch whilst charging will
enable sleep mode. This keeps the Rapid Charge
15k charging.
Charging Time
The charging time will depend on the output
power of the AC wall adapter.
If using a 1A Wall Adapter it will need at least 9
hours to fully charge.
Note: Please recharge the Rapid Charge 15k
every 3 months if it is not being used regularly.

Trouble Shooting
Problems Possible
Causes Corrective Actions
Unit has been
charging for
long time but
indicators
don’t show full
capacity
1. Charging
time is not
enough
2. Adapter
output current
is too low
1. Ensure it has
been charging
for at least 9
hours
2. Use the
original cable
and a certified
AC adapter
The Rapid
Charge 15k
can not fully
charge other
devices.
1. No power
or low power
left.
2. Failed input
cable and
connectors, or
connector is
incorrect.
1. Charge it
again.
2. Use another
output cable
and connector
or the original
device cable.
Rapid Charge
15k could not
charge device,
continuously,
or intermit-
tently charges
devices. Two
beeps may
happen.
1. Failed cable
or connector.
2. Low power
left.
3. Device may
need higher
input voltage
than available.
1. Use an-
other cable or
check con-
nector.
2. Charge it
again.
3. Please
don’t use the
device when
charging nor
charge your
device when it
has remaining
charge.

When Rapid
Charge 15k
charges a
phone the
phone turns
on flight
mode.
1. Phone can-
not iden-
tify the Rapid
Charge 15k
when using a
non-genuine
cable or low
quality cable.
2. Cable
connection
incorrectly
plugged in.
1. Use another
cable or use
the original
cable with
your device.
2. Reconnect
the cell phone
or adjust it to
normal mode.
The power
indicators
flash suddenly
1. The Rapid
Charge 15k
will warn and
cut o power
automati-
cally when
the internal
temperature
reaches 65°C
1. Please
disconnect
the cable
and place the
Rapid Charge
15k in a cool,
clean and well
ventilated
place.
Try again
when the
internal
temperature is
below 55°C.
Stops charg-
ing a device 1. No power left
2. The load is
over limit
3. Short circuit
for protection.
1. Recharge
the Rapid
Charge 15k.

Support
Having trouble with your Rapid Charge 15k?
Please contact us. No question too big or small
and we are more than happy to help.
Please visit:
www.kaiserbaas.com/support
Or email:
[e-mail]
For further information please visit:
www.kaiserbaas.com/