Kalamazoo 1SMVP User manual

KALAMAZOO
INDUSTRIES, INC.
KALAMAZOO, MI
PH: [phone] www.kalamazooind.com
KI
MADE IN USA
1SMVP MULTI POSITION
BELT SANDER MANUAL

KALAMAZOO
INDUSTRIES, INC.
KALAMAZOO, MI
PH: [phone] www.kalamazooind.com
KI
WARNING!
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN, ANY LIQUID OR MOISTURE.
INSPECTION
If these goods are damaged in transit, the DELIVERING TRANSPORTATION
COMPANY is required by law to make notation of damages on the freight bill. If in your
opinion, there may be concealed damage, they are required to make an inspection after goods are
unpacked. Transportation rates are made in proportion to damage. Therefore, the carrier and
NOT the shipper should be charged with any loss or damage. Any claim should be lled with
the delivering TRANSPORTATION COMPANY. PLEASE DO NOT RETURN GOODS
TO US WITHOUT OUR RGA NUMBER AND SHIPPING INSTRUCTIONS.
NOTE: SEE NEXT PAGE FOR RETURN POLICY AND WARRANTY.
IMPORTANT
Read Operating Instructions before using equipment.
OPERATING INSTRUCTION
1. Disconnect power before making any adjustments.
2. Abrasive belt rotation is counter-clockwise. If the abrasive belt is lap spliced be sure of the correct belt
rotation. Butt spliced belts bi-directional.
3. Belt tension is pre-set with internal spring (12). No belt tension adjustment is required.
4. To change belt disconnect power, loose tracking knob (22), open belt guard (17), compress spring belt
tension by pushing down on tension shaft (13), remove belt and replace with new belt of your choice.
5. Belt tracking- with power disconnected rotate belt by hand to center or “track” sanding belt. Rotate tracking
knob (22) and tracking collar (21), left and or right turns the tension shaft (13) to “track” the belt. Re-lock
the tracking knob (22) to lock in belt tracking. Close belt guard (17) and reconnect connect power.

KALAMAZOO
INDUSTRIES, INC.
KALAMAZOO, MI
PH: [phone] www.kalamazooind.com
KI
WARRANTY
All products are guaranteed for a period of one year from receipt of order to the original purchaser,
against defects in material workmanship under normal use. Electric motors are warranted by the motor
manufacturer for a period of one year and will be repaired by the nearest motor repair station. If non-
repairable, they will be replaced by Kalamazoo Industries. Please call for instructions [phone].
RETURN POLICY
Authorization must be obtained before returning merchandise. Please call our customer service
department for a return authorization number [phone]. Please include with your return a copy of
your invoice of packing slip. All material must be new and unused in the original packaging. Material
must be sent back prepaid (unless otherwise indicated) by Kalamazoo Industries. Credit upon inspection
at Kalamazoo Industries. All returns will be subject to a 10% restock charge. Used merchandise is non-
returnable. No returns will be accepted after one year of invoice date.
BELT SANDER SAFETY
• READ THE OPERATING INSTRUCTIONS BEFORE RUNNING MACHINE.
• ALWAYS WEAR SAFETY GLASSES OR A FULL FACE SHIELD FOR PROTECTION.
• KEEP HANDS CLEAR OF THE SANDING AREA.
• NEAR WEAR GLOVES OR LOOSE FITTING CLOTHES WHEN OPERATING THIS
MACHINE.
• ALWAYS KEEP HAIR TIED BACK OR COVERED.
• LET MACHINE ROTATION COME TO A FULL STOP BEFORE CHANGING BELT.
• KEEP SAFETY GUARDS IN PLACE. DO NOT ALTER GUARD OR MACHINE IN ANYWAY.
ANY ALTERATIONS TO GUARDS OR MACHINE COULD CAUSE SERIOUS INJURY.
• ALL BELT SANDERS SHOULD BE OPERATED IN A WELL-VENTILATED AREA. THE
DUST CREATED WHEN SOME MATERIALS ARE SANDED CAN BE HARMFUL. DUST
MASKS ARE RECOMMEND AS A PRACTICAL MEAN OF MINIMIZING DUST
INHALATION. FUMES FROM OTHER OTHER SOURCES CAN ALSO CAUSES FIRES
WHEN INTACT WITH SANDING SPARK.
• SPARKS CREATED BY SANDING SHOULD BE DIRECTED DOWNWARD AND AWAY
FROM THE FACE AND BODY. DON NOT GRIND NEAR FLAMMABLE MATERIAL.
• ELECTRIC SANDING MACHINES ARE NOT INTENDED FOR USE IN OR NEAR WATER.
THIS INCLUDES AN OPERATOR STANDING ON A WET FLOOR OR WORKING
AROUND CONTAINERS OF WATER OR OTHER CONDUCTIVE LIQUIDS.

21.5
12.6
A
A
C
C
FRONT VIEW
1
2
7
10
3
4
11
13
21
22
17
9
8
1
2
7
10
11
21
22
17
9.0
B
DD
EE
SECTION A-A
SCALE 1 : 2
1
10
11
2
SPRING IS COMPRESSED AND
HELD IN PLACE BY THE BELT
7
21
13
12
1415
8
17
18
4
5
6
X 2 PLACES
2
DETAIL B
SCALE 2 : 1
MOTOR MOUNT DETAILS
3
4
4
5
6
X 4 PLACES
SECTION C-C
SCALE 1 : 2
PIVOT DETAILS
7
8
9
8
9
LOOSEN FASTENERS
TO TILT
SECTION D-D
SCALE 1 : 2
DRIVE PULLEY DETAILS
8
9
8
9
19
20
18
SECTION E-E
SCALE 1 : 2
14 15 8
16
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
291-056BASE
BASE WITHOUT TUBE SUPPORT FOR
1SMVP
1
2
486-021
1/3HP MOTOR FOR 1SM
1
3
HHC5025012
1/4-20 X 3/4 HHCS GR5 Z
5
4
UFWZ025
1/4 USS F/W Z
11
5
SLWZ025
1/4 SPLIT L/W Z
6
6
FHN5025
1/4-20 FHN GR5 Z
6
7
832-025
TUBE SUPPORT WITH MOUNTING
PLATE FOR 1SMVP
1
8
SLWZ037
3/8 SPLIT L/W Z
3
9
FHN5037
3/8-16 FHN GR5 Z
2
10
563-047
STANDARD PLATEN FOR 1SMVP
1
11
829-013
1SM WORK TABLE
1
12
697-020
TENSION SPRING FOR 1SM AND 1SK6
SANDERS
1
13
700-005
TENSION SHAFT FOR 1SM, 1SK6
SANDERS
1
14
560-018
1SM IDLER PULLEY
1
15
HHC5037032
3/8-16 X 2 HHCS GR5 Z
1
16
UFWZ037
3/8 USS F/W Z
1
17
342-087
1SM, 1SK6 GUARD FOR IDLER PULLEY
1
18
560-017
1SM DRIVE PULLEY
1
19
SSKA025006
1/4-20 X 3/8 SOC SET KNURL PT.
1
20
SSSA025024
1/4-20 X 1-1/2 SOC SET CUP PT.
1
21
123-015
TRACKING COLLAR FOR 1SM, 1SK6,
S1
1
22
441-015
TRACKING KNOB
1
A A
B B
C C
D D
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
1 X 42 BELT SANDER/
VARIABLE POSITION
DO NOT SCALE DRAWING
1SMVP
SHEET 1 OF 1
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:5
WEIGHT:
REV
SIZE
DWG. NO.
D
TITLE:
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NEXT ASSY
PROPRIETARYAND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.