Kaltech DW-709 User manual

•This manual is published by Kaltech and contains information on DW-709/716 which will
enable you to use this product properly.
• If you require additional copies of this manual, please print the manual contained in the CD
provided with your purchase.
DDWW--770099//771166MMaannuuaall

Thank you for purchasing Kaltech DW-709/716 .
This DVR is produced by the most advanced Kaltech technology and its quality is guaranteed
by strict reliability and compatibility testing.
This DW-709/716 manual provides necessary information for the correct use of this product
and also contains some useful tips.
Please read this manual thoroughly before using DW-709/716 in order to prevent possible
breakdown due to any mishandling.
IInnttrroodduuccttiioonn

Manual Edition 7.03 – March 2005
©2003-2005, Kaltech Enterprises
All Rights reserved.
No part of this documentation may be reproduced in any means, electronic or mechanical, for any
purpose, except as expressed in the Software License Agreement. Digital Watchdog shall not be liable
for technical or editorial errors or omissions contained herein. The information in this document is
subject to change without notice.
The information in this publication is provided “as is”without warranty of any kind. The entire risk
arising out of the use of this information remains with recipient. In no event shall Digital Watchdog be
liable for any direct, consequential, incidental, special, punitive, or other damages whatsoever
(including without limitation, damages for loss of business profits, business interruption or loss of
business information), even if Digital Watchdog has been advised of the possibility of such damages
and whether in an action or contract or tort, including negligence.
This software and documentation are copyrighted. All other rights, including ownership of the
software, are reserved to DIGITAL WATCHDOG INCORPORATED. DIGITAL WATCHDOG,
Digital Watchdog, DW-Pro, and High Definition Digital Recorder are registered trademarks of
Kaltech Enterprises Inc in the United States and elsewhere; Windows, and Windows 2000 are
registered trademarks of Microsoft Corporation; DirectCD is a registered trademark of Roxio
Corporation. All other brand and product names are trademarks or registered trademarks of the
respective owners.
The following words and symbols mark special messages throughout this guide:
WARNING: Text set off in this manner indicates that failure to
follow directions could result in bodily harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to
follow directions could result in damage to equipment or loss of
information.
Kaltech Enterprises
5436 W Crenshaw St ·Tampa, FL 33634 ·U.S.A
Office 1-813-888-9555 ·Fax [phone] ·Tech Support 1-866-446-3595 Ext 242
Kaltech Enterprises
User’s guide for DW-709/716 DVR.
This manual applies to DW-709/716 DVR only.
This manual describes external features of the DW-709/716 DVR, part names, correct
connection methods for supported domes or Pan/Tilt receivers, control devices, peripheral
devices, and the system set up instructions. It should be noted that some features, figures,
pictures and references can only be applied to one model either DW-709 or DW-716.
•Kaltech can not be held responsible if the DVR is damaged due to non-compatible devices
being used with this product. If you have any doubts please check.
•Kaltech can not be held responsible if the DVR is damaged due to the product being
disassembled or modified by the user.
•If you wish to open the system casing to attempt to modify, repair, or upgrade the system, it
is recommended that you ask for a Kaltech engineer’s assistance by contacting either your
dealer or Kaltech head office.
•DigiNet and DW-709/716 are registered trademarks of Kaltech
•This product is qualified for both domestic and industrial use. This product is qualified under
the Radio Equipment Requirements of Korea and acquired international certification
including CE (Europe) and FCC (USA).
NNoottiiccee

the SOFTWARE may be used only in connection with a hard drive(s) that is (are)
permanently connected to ONE specific DW-Pro computer (either a stand-alone computer
or a computer connected to a network) owned or leased by you. If the SOFTWARE is made
available on a network, only ONE specific DW-Pro computer may access it. Once the
SOFTWARE has been accessed, by ONE specific computer, it may not be used on any
additional computers without acquiring additional licenses from Ka ltech Enterprises.
ii. PERSONAL LICENSE AND COMPUTER-SPECIFIC LICENSE FOR THE CLIENT
SOFTWARE.
You the End User are authorized to use the client software on NO MORE THAN 30
computers. All copies of the SOFTWARE must include the Kaltech Enterprises copyright,
confidentiality, trademark and patent notices. This License is personal to you. You may
not sublicense, lease, sell or otherwise transfer the Software or any of the accompanying
documentation to any other person. You may use the Software only for your own personal
use if you are an individual or for your own internal business purposes if you are a
business. Each permitted copy of the SOFTWARE may be used only in connection with a
hard drive(s) that is (are) permanently connected to ONE specific DW-Pro computer (either
a stand-alone computer or a computer connected to a network) owned or leased by you.
If the SOFTWARE is made available on a network, only ONE specific DW-Pro computer
may access it. Once the SOFTWARE has been accessed, by ONE specific computer, it may
not be used on any additional computers without acquiring additional licenses from
Kaltech Enterprises.
b. SERVER USE. To the extent that the applicable product invoicing or packaging sets forth,
you may use the SOFTWARE on a Client Device or as a server (“Server”) within a multi-
user or networked environment (“Server Use”) for either (i) connecting, directly or
indirectly, to not more than the maximum number of specified Client Devices, or (ii)
deploying not more than the maximum number of agents (pollers) specified for
deployment. If the applicable product invoicing or packaging does not specify a
maximum number of Client Devices, or pollers, this is a single product use license subject to
subsection (a) above. A separate license is required for each Client Device or “seat”that
may connect the SOFTWARE at any time, regardless of whether such licensed Client
Devices or seats are connected to the SOFTWARE concurrently, or are actually using the
SOFTWARE at any particular time. Your use of software or hardware that reduces the
number of Client Devices or seats that connect to and use the SOFTWARE directly
or simultaneously (e.g., “multiplexing”or “pooling”software or hardware) does not reduce
the number of licenses required. Specifically, you must have that number of licenses that
would equal the number of distinct inputs to the multiplexing or pooling software or
hardware “front end”). If the number of Client Devices or seats that can connect to the
SOFTWARE can exceed the number of licenses you have obtained, then you must have a
reasonable mechanism in place to ensure that your use of the SOFTWARE does not exceed
the use limits specified for the license you have obtained. This license authorizes you to
make or download one copy of the Documentation for each Client Device or seat that is
licensed, provided that each such copy contains all the proprietary notices for the
Documentation.
DIGITAL WATCHDOG END-USER SOFTWARE LICENSE AGREEMENT
Version 1.0, June 2001
IMPORTANT: Read this before using any commercial software available from Kaltech Enterprises
This document (“License”) is a legal agreement between you (an individual or business) and Kaltech
Enterprises Inc (“Kaltech Enterprises”). Use of the enclosed or downloaded software indicates your
acceptance of these terms. As used in this License Agreement, the term “SOFTWARE”means the
software included on the CD, via download or disk media provided with this License Agreement.
The term “SOFTWARE”does not include any software that is covered by a separate license offered or
granted by a person other than Kaltech Enterprises and this License does not grant any rights in such
software.
Copyright laws and international copyright treaties, as well as other intellectual property laws and
treaties protect the SOFTWARE. The SOFTWARE is licensed, not sold.
IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS, EITHER DESTROY, OR
RETURN INTACT, THE SOFTWARE PACKAGE, CONTAINING THE CD OR DISK MEDIA,
TOGETHER WITH THE OTHER COMPONENTS OF THE PRODUCT TO THE PLACE OF
PURCHASE FOR A REFUND OF THE PURCHASE PRICE.
1. PROPRIETARY RIGHTS. The SOFTWARE, HARDWARE and any associated
documentation are proprietary products of Kaltech Enterprises or its licensors. And are protected
under U.S. and European copyright, trademark, patent and trade secret laws and international treaty
provisions. Sole ownership of the SOFTWARE, HARDWARE and all copies, modifications,
translations, and merged portions thereof shall at all times remain with Kaltech Enterprises or its
licensors.
2. GRANT OF LICENSE AND TERM. The SOFTWARE and accompanying documentation
are being licensed to you. This means you have the right to use the SOFTWARE only in accordance
with this license agreement. The SOFTWARE is considered in use on a computer when it is loaded
into temporary memory or installed into permanent memory. This license may not be assigned or
otherwise transferred without prior written consent from Kaltech Enterprises, and any unauthorized
transfer makes the license null and void.
a. LICENSING
i. PERSONAL LICENSE AND COMPUTER-SPECIFIC LICENSE FOR THE
SERVER SOFTWARE.
You the End User are authorized to use the server software on NO MORE THAN the
number of DW-Pro computers for which you have purchased licenses. All copies of the
SOFTWARE must include the Kaltech Enterprises copyright, confidentiality, trademark and
patent notices. This License is personal to you. You may not sublicense, lease, sell or
otherwise transfer the Software or any of the accompanying documentation to any other
person. You may use the Software only for your own personal use if you are an individual
or for your own internal business purposes if you are a business. Each permitted copy of

SOFTWARE are expressly prohibited. Provided, however, that nothing in these conditions shall
restrict (i) decompiling, notwithstanding that decompiling may involve adaptation, if the sole purpose
of such decompiling is to achieve the interoperability of an independently created program with other
programs, or (ii) any other act permitted to the End User by applicable laws and regulations of the
End User’s jurisdictions.
5. NON-PERMITTED USES. Without the express prior written permission of Kaltech
Enterprises you may not (a) use, copy, modify, alter or transfer electronically or otherwise, the
SOFTWARE or documentation except as expressly permitted in this License Agreement, or (b)
translate, reverse program, disassemble, decompile, or otherwise reverse engineer the SOFTWARE.
6. U.S. GOVERNMENT RESTRICTED RIGHTS. If you are acquiring the SOFTWARE on
behalf of any unit or agency of the United States Government, the following provision applies: It is
acknowledged that the SOFTWARE and the documentation were developed at private expense and
that no part is in the public domain and that the SOFTWARE and documentation are provided with
RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as
set forth in subparagraph (C)(1)(ii) of the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013 or subparagraphs c (1) and (2) of the Commercial Computer Software-Restricted
Rights at 48 CFR 52.227-19, as applicable. Contractor/Manufacturer is Kaltech Enterprises 5436 W
Crenshaw St Tampa FL33634
7. EXPORT CONTROLS. Certain uses of the SOFTWARE by the End User maybe subject to
restrictions under U.S. regulations relating to exports and ultimate end uses of computer software.
The End User agrees to fully comply with all applicable U.S. laws and regulations, including but not
limited to the Export Administration Act of 1979 as amended from time to time and any regulations
promulgated there under.
8. LIMITED WARRANTY. (a) Kaltech Enterprises warrants to the End User, (i) that the
SOFTWARE (not including any third-party software) will perform substantially in accordance with
the associated documentation and (ii) that the SOFTWARE is properly recorded on the disk media.
This Limited Warranty extends for (90) days from the date of purchase of this License. Kaltech
Enterprises does not warrant any third-party software that is provided with the SOFTWARE, but
Kaltech Enterprises agrees to pass on the End User any warranties of the owner of licensor to the
extent permitted by the owner or licensor. (b) This Limited Warranty does not apply to any software
that has been altered, damaged, abused, mis-applied, or used other than in accordance with this
License and any instructions included on the SOFTWARE and the associated documentation. (c)
Kaltech Enterprises’s entire liability under this Limited Warranty shall be the repair or replacement of
any SOFTWARE that fails to conform with this Limited Warranty or, at Kaltech Enterprises’s option,
the return price paid for this license. Kaltech Enterprises shall have no liability under this Limited
Warranty unless the SOFTWARE is returned to Kaltech Enterprises or its authorized representative,
with a copy of the End User’s receipt, within the warranty period or 30 days, whichever is longer. (d)
THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT
EXPRESSLY SET FORTH HEREIN, WHETHER EXPRESS OF IMPLIED, SUBJECT TO CONTRARY
ORDER PUBLIC REQUIREMENTS IN THE END USER’S JURISDICTION. (e) The End User’s failure
to return the enclosed registration card or complete the electronic registration included with the
SOFTWARE may result in Kaltech Enterprises’s inability to provide the End User with updates to the
SOFTWARE, and the End User assumes the entire risk of performance and result in such en event.
c. VOLUME USE. If the SOFTWARE is licensed with volume use terms specified in the
applicable product invoicing or packaging, you may make, use and install as many
additional copies of the SOFTWARE on the number of Client Devices as the volume use
terms authorize. You must have a reasonable mechanism in place to ensure that the
number of Client Devices on which the SOFTWARE has been installed does not exceed the
number of licenses you have obtained. This license authorizes you to make or download
one copy of the Documentation for each additional copy authorized by the volume license,
provided that each such copy contains all of the proprietary notices for the Documentation.
d. STORAGE/NETWORK USE. You may also store or install a copy of the SOFTWARE on
a storage device, such as a network server, used only to install or run the SOFTWARE on
your other computers over an internal network; however, you must acquire and dedicate a
license for each separate computer on which the SOFTWARE is installed or run form
thestorage device. A license for the SOFTWARE may not be shared or used concurrently
on different computers.
e. TERM. (i) This License is effective form the date of purchase of the License and shall
remain in force until terminated. The End User may terminate this License at any time by
destroying the SOFTWARE and its associated documentation, together with all copies of
any form. (ii) Notwithstanding subparagraph d(i) above, this License may be terminated at
any time by written notice of termination given by Kaltech Enterprises to the End User in
any of the following circumstances: (A) If the End User shall expressly or impliedly
repudiate this License by refusing or threatening to refuse to observe any of the conditions
to which this License is subject; or (B) If the End User shall fail to make any payment due
under and pursuant to this License or to observe any of the conditions to which this License
is subject and, after the End User’s attention has been drawn by notice to such failure, shall
fail to remedy the matter to Kaltech Enterprises’s reasonable satisfaction within thirty days
of the giving of such notice;; or (C) If the End User shall have a receiver or administrative
receiver or administrator appointed or shall enter into liquidation whether compulsory or
voluntary or it the End User shall be unable to pay its debts as and when they fall due.
(iii) On expiry, surrender, or other termination of this License, however such termination
may arise, the End User shall cease to load, store, copy or use the Software and the a
ssociated documentation, shall delete the SOFTWARE from its computers and shall either
surrender the SOFTWARE and the associated documentation, together with all copies in
any form, to Kaltech Enterprises or shall destroy the same. The End User shall continue
termination to observe and enforce confidentiality and secrecy in respect of the SOFTWARE
and its associated documentation for the benefit of Kaltech Enterprises, and however
termination may occur it shall not prejudice any right of action or remedy, which may have
occurred prior to termination.
3. BACKUP COPY. In addition to any copies authorized for use under this License, the End
User may make a single copy of the SOFTWARE solely for backup purposes.
4. INTEGRITY OF THE SOFTWARE. The End User shall not enhance or vary any part of the
SOFTWARE nor procure or permit the whole or any part of the SOFTWARE (whether in its original
or in any updated, enhanced, or varied form) to be incorporated into any other software or computer
system. Translations, reverse programming, disassembling, and reverse engineering of the

9. CONFIDENTIALITY AND CONTROL OF THE SOFTWARE. The SOFTWARE, all
associated documentation, and all copies are secret and confidential to Kaltech Enterprises and shall
be retained under the effective control of the End User during the period of this License. The End
User shall take all measures necessary to preserve confidentiality and secrecy in the SOFTWARE
during the period of this License and after its termination, however such termination may arise.
10. INDEMNITIES AND LIMITATION OF LIABILITY. (a) Subject to 9(b) below, Kaltech
Enterprises warrants to the End User that the Software as supplied by Kaltech Enterprises will not
infringe any copyright, patent, or other intellectual property right of any third party. Conditionally
upon the End User’s promptly giving notice to Kaltech Enterprises of any claim of alleged
infringement and allowing Kaltech Enterprises to have sole control of negotiations on, and any
defense of the claim, Kaltech Enterprises shall in its discretion and at its own cost wither compromise
or defend the claim and shall hold the End User harmless from any resulting final judgment, order, or
settlement. Kaltech Enterprises shall have the right to replace or change the SOFTWARE so as to
avoid infringement and require the End User to accept a license to use such replaced or changed
SOFTWARE in substitution for this License, provided that the SOFTWARE as substituted is
substantially suitable for the End User’s utilization. (b) Kaltech Enterprises’s maximum liability to
the End User under 9(a) above shall not exceed the License fees actually paid by the End User for the
SOFTWARE. If Kaltech Enterprises becomes aware of a potential claim under 9(a) above, Kaltech
Enterprises shall be entitled then or at anytime thereafter to discharge its liabilities (including
potential, accruing, and accrued liabilities) to the End User under 9(a) above by requiring the End
User to surrender this License and to cease use of the SOFTWARE upon Kaltech Enterprises’s paying
to the End User a sum equivalent to the maximum amount of Kaltech Enterprises’s liability as stated
above. (c) GENERAL LIMITATION OF LIABILITY AND INDEMNITIES. KALTECH
ENTERPRISES’S MAXIMUM LIABILITY RELATED TO ANY OF THE SOFTWARE SHALL NOT
EXCEED THE LICENSE FEES ACTUALLY PAID BY THE END USER FOR THE SOFTWARE.
FOR BELGIUM, FRANCE, IRELAND, AND THE NETHERLANDS: IN NO EVENT SHALL
KALTECH ENTERPRISES BE LIABLE TO THE END USER, EXCEPT IN RESPECT OF (a) DEATH,
PERSONAL INJURY, OR DAMAGE TO PROPERTY CAUSED BY KALTECH ENTERPRISES’S
NEGLIGENCE OR (b) KALTECH ENTERPRISES’S GROSS NEGLIGENCE OR WILLFUL
MISCONDUCT, FOR AN AMOUNT IN EXCESS OF THE MAXIMUM AMOUNT OF KALTECH
ENTERPRISES’S LIABILITY AS STATED IN 9(b) ABOVE, BY REASON OF ANY
REPRESENTATION OR IMPLIED WARRANTY, CONDITION, OR OTHER TERM OR ANY DUTY
AT LAW, OR UNDER THE TERMS OF THIS AGREEMENT, FOR ANY CONSEQUENTIAL LOSS
OR DAMAGE (WHETHER FOR LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF
BUSINESS INFORMATION, OR OTHERWISE) ARISING OUT OF OR IN CONNECTION WITH
ANY ACT OR OMISSION OF KALTECH ENTERPRISES RELATING TO THE USE OR INABILITY
TO USE THE PRODUCT BY THE END USER.
FOR GREECE: IN NO EVENT SHALL KALTECH ENTERPRISES BE LIABLE TO THE END USER,
EXCEPT IN RESPECT OF DEATH, DAMAGE TO PROPERTY OR PERSONAL INJURY CAUSED
BY KALTECH ENTERPRISES’S FRAUD OR GROSS NEGLIGENCE, FOR AN AMOUNT IN
EXCESS OF THE MAXIMUM AMOUNT OF KALTECH ENTERPRISES’S LIABILITY AS STATED
IN 9(b) ABOVE, BY REASON OF ANY REPRESENTATION OR IMPLIED WARRANTY,
CONDITION, OR OTHER TERM OR ANY DUTY AT LAW, OR UNDER THE TERMS OF THIS
AGREEMENT, FOR ANY CONSEQUENTIAL LOSS OR DAMAGE (WHETHER FOR LOSS OF
PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHERWISE)
ARISING OUT OF OR IN CONNECTION WITH ANY ACT OR OMISSION OF KALTECH
ENTERPRISES RELATING TO THE USE OR INABILITY TO USE THE PRODUCT BY THE END
USER.
FOR ITALY: IN NO EVENT SHALL KALTECH ENTERPRISES BE LIABLE TO THE END USER,
EXCEPT IN RESPECT OF DEATH, DAMAGE TO PROPERTY OR PERSONAL INJURY CAUSED
BY KALTECH ENTERPRISES’S FRAUD OR GROSS NEGLIGENCE OR VIOLATION OF A DUTY
ARISING FORM APPLICABLE ORDINE PUBBLICO RULES FOR AN AMOUNT IN EXCESS OF
THE MAXIMUM AMOUNT OF KALTECH ENTERPRISES’S LIABILITY AS STATED IN 9(b)
ABOVE, BY REASON OF ANY REPRESENTATION OR IMPLIED WARRANTY, CONDITION, OR
OTHER TERM OR ANY DUTY AT LAW, OR UNDER THE TERMS OF THIS AGREEMENT, FOR
ANY CONSEQUENTIAL LOSS OR DAMAGE (WHETHER FOR LOSS OF PROFIT, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHERWISE) ARISING OUT OF OR
IN CONNECTION WITH ANY ACT OR OMISSION OF KALTECH ENTERPRISES RELATING TO
THE USE OR INABILITY TO USE THE PRODUCT BY THE END USER.
FOR DENMARK, FINLAND AND NORWAY: IN NO EVENT SHALL KALTECH ENTERPRISES BE
LIABLE TO THE END USER, EXCEPT (i) IN RESPECT OF DEATH OR PERSONAL INJURY
CAUSED BY KALTECH ENTERPRISES’S GROSS NEGLIGENCE OR WILLFUL MISCONDUCT OR
(ii) IF SUCH LIABILITY LIMITATION IS UNREASONABLE UNDER ALL RELEVANT
CIRCUMSTANCES , FOR AN AMOUNT IN EXCESS OF THE MAXIMUM AMOUNT OF
KALTECH ENTERPRISES’S LIABILITY AS STATED IN 9(b) ABOVE, BY REASON OF ANY
REPRESENTATION OR IMPLIED WARRANTY, CONDITION, OR OTHER TERM OR ANY DUTY
AT LAW, OR UNDER THE TERMS OF THIS AGREEMENT, FOR ANY CONSEQUENTIAL LOSS
OR DAMAGE (WHETHER FOR LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF
BUSINESS INFORMATION, OR OTHERWISE) ARISING OUT OF OR IN CONNECTION WITH
ANY ACT OR OMISSION OF KALTECH ENTERPRISES RELATING TO THE USE OR INABILITY
TO USE THE PRODUCT BY THE END USER.
FOR PORTUGAL: IN NO EVENT SHALL KALTECH ENTERPRISES BE LIABLE TO THE END
USER, EXCEPT IN RESPECT OF DEATH, DAMAGE TO PROPERTY OR PERSONAL INJURY
CAUSED BY KALTECH ENTERPRISES’S GROSS NEGLIGENCE OR WILLFUL MISCONDUCT,
FOR AN AMOUNT IN EXCESS OF THE MAXIMUM AMOUNT OF KALTECH ENTERPRISES’S
LIABILITY AS STATED IN 9(b) ABOVE, BY REASON OF ANY REPRESENTATION OR IMPLIED
WARRANTY, CONDITION, OR OTHER TERM OR ANY DUTY AT LAW, OR UNDER THE
TERMS OF THIS AGREEMENT, FOR ANY CONSEQUENTIAL LOSS OR DAMAGE (WHETHER
FOR LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR
OTHERWISE) ARISING OUT OF OR IN CONNECTION WITH ANY ACT OR OMISSION OF
KALTECH ENTERPRISES RELATING TO THE USE OR INABILITY TO USE THE PRODUCT BY
THE END USER.
FOR SPAIN: IN NO EVENT SHALL KALTECH ENTERPRISES BE LIABLE TO THE END USER,
EXCEPT IN RESPECT OF DEATH, DAMAGE TO PROPERTY OR PERSONAL INJURY CAUSED
BY KALTECH ENTERPRISES’S BAD FAITH CONDUCT, FOR AN AMOUNT IN EXCESS OF THE
MAXIMUM AMOUNT OF KALTECH ENTERPRISES’S LIABILITY AS STATED IN 9(b) ABOVE, BY

REASON OF ANY REPRESENTATION OR IMPLIED WARRANTY, CONDITION, OR OTHER
TERM OR ANY DUTY AT LAW, OR UNDER THE TERMS OF THIS AGREEMENT, FOR ANY
CONSEQUENTIAL LOSS OR DAMAGE (WHETHER FOR LOSS OF PROFIT, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHERWISE) ARISING OUT OF OR
IN CONNECTION WITH ANY ACT OR OMISSION OF KALTECH ENTERPRISES RELATING TO
THE USE OR INABILITY TO USE THE PRODUCT BY THE END USER.
FOR SWEDEN: IN NO EVENT SHALL KALTECH ENTERPRISES BE LIABLE TO THE END USER,
EXCEPT IN RESPECT OF DEATH, DAMAGE TO PROPERTY OR PERSONAL INJURY CAUSED
BY KALTECH ENTERPRISES’S GROSS NEGLIGENCE OR WILLFUL MISCONDUCT, FOR AN
AMOUNT IN EXCESS OF THE MAXIMUM AMOUNT OF KALTECH ENTERPRISES’S LIABILITY
AS STATED IN 9(b) ABOVE, BY REASON OF ANY REPRESENTATION OR IMPLIED
WARRANTY, CONDITION, OR OTHER TERM OR ANY DUTY AT LAW, OR UNDER THE
TERMS OF THIS AGREEMENT, FOR ANY CONSEQUENTIAL LOSS OR DAMAGE (WHETHER
FOR LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR
OTHERWISE) ARISING OUT OF OR IN CONNECTION WITH ANY ACT OR OMISSION OF
KALTECH ENTERPRISES RELATING TO THE USE OR INABILITY TO USE THE PRODUCT BY
THE END USER.
FOR THE UNITED KINGDOM: IN NO EVENT SHALL KALTECH ENTERPRISES BE LIABLE TO
THE END USER, EXCEPT IN RESPECT OF (a) DEATH OR PERSONAL INJURY CAUSED BY
KALTECH ENTERPRISES’S NEGLIGENCE OR (b) DAMAGE TO PROPERTY OR OTHER LOSS
CAUSED BY KALTECH ENTERPRISES WHERE SUCH LIABILITY LIMITATION IS
UNREASONABLE UNDER ALL RELEVANT CIRCUMSTANCES. FOR AN AMOUNT IN EXCESS
OF THE MAXIMUM AMOUNT OF KALTECH ENTERPRISES’S LIABILITY AS STATED IN 9(b)
ABOVE, BY REASON OF ANY REPRESENTATION OR IMPLIED WARRANTY, CONDITION, OR
OTHER TERM OR ANY DUTY AT LAW, OR UNDER THE TERMS OF THIS AGREEMENT, FOR
ANY CONSEQUENTIAL LOSS OR DAMAGE (WHETHER FOR LOSS OF PROFIT, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHERWISE) ARISING OUT OF OR
IN CONNECTION WITH ANY ACT OR OMISSION OF KALTECH ENTERPRISES RELATING TO
THE USE OR INABILITY TO USE THE PRODUCT BY THE END USER
11. NO LIABILITY FOR DAMAGES, INCLUDING WITHOUT LIMITATION
CONSEQUENTIAL DAMAGES
In no event shall Kaltech Enterprises or its Licensor's be liable for any damages whatsoever
(including, without limitation, incidental, direct, indirect, special or consequential damages, damages
for loss of business profits, business interruption, loss of business information, or other pecuniary loss)
arising out of the use or inability to use this Software, even if Kaltech Enterprises or its Licensor's have
been advised of the possibility of such damages. Because some states/ countries do not allow the
exclusion or limitation of liability for consequential or incidental damages, the above limitation may
not apply to you.
12. NO WAIVER. Any failure by either party to this agreement to enforce a specific part of the
agreement in a specific situation is not a waiver of rights under the agreement. The party may still
enforce the rest of the agreement in that situation and may still enforce some or all of the agreement in
other situations.
13. This License constitutes the entire agreement between the End User and KALTECH
ENTERPRISES pertaining to its subject matter. This License is governed by the laws of the State of
Washington (except the body of laws controlling conflict laws). The state and federal courts having
appropriate jurisdiction over the State of Washington will pursue any litigation arising from this
license. Even if part of the agreement is held invalid, the rest of the agreement shall still be valid,
binding, and enforceable. The failure of either party to exercise a right does not waive future exercise
of that right or other rights.
Should the End User have any questions concerning this License, or if the End User desires to contact
Kaltech Enterprises for any reason, please write: Kaltech Enterprises 5436 W Crenshaw St Tampa Fl
33634
Copyright© 2001, Kaltech Enterprises All rights reserved.
Safety Precautions

Safety Precautions
WARNING: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT
OPEN THE CABINET. REFER SERVICING TO QUALIFIED
PERSONNEL ONLY.
SURGE PROTECTION: A UPS IS MANDATORY FOR EFFICIENT FUNCTIONING OF YOUR
DIGITAL .
IMPORTANT SAFETY INSTRUCTIONS
1. Read Owner Manual
After unpacking this product, read the owner manual carefully, and follow all the operating
and other instructions.
2. Power Sources
This product should be operated only from the type of power source indicated on the label. If
you are not sure of the type of power supply to your home or business, consult your product
dealer or local power company.
3. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation
of the product and to protect it from overheating, and these openings must not be blocked or
covered. The product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer instructions have been adhered
to.
4. Heat
The product should be situated away from heat sources such as radiators. Heat registers,
stoves, or other product that produce heat.
5. Water and Moisture
Do not use this product near water. Do not exceed the humidity specifications for the product
as detailed in the Appendix section in this manual.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Power Cord Protection
Power-supply cords should not be routed so that they are not likely to be walked on or
pinched by items placed against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the product.
8. Overloading
Do not overload wall outlets; extension cords, or integral convenience receptacles as this can
result in a risk of fire or electrical shock.
9. Lightning
For added protection for this product during storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet. This will prevent damage to the
product due to lightning and power line surges.
10. Object and Liquid Entry Points
Never insert foreign objects into the DW-Pro unit, other than the media types approved by
Kaltech Enterprises, as they may touch dangerous voltage points or short-out parts that could
result in a fire or electrical shock. Never spill liquid of any kind on the product.

11. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may
fall, causing serious personal injury and serious damage to the product.
12. Disc Tray
Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause
serious personal injury.
13. Burden
Do not place a heavy object on or step on the product. The object may fall, causing serious
personal injury and serious damage to the product.
14. Disc
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause
serious personal injury and product malfunction.
15. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions.
�When the power Supply cord or plug is damaged.
�If liquid has been spilled, or objects have fallen into the product.
�If the product has been exposed to rain or water.
�If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
�If the product has been dropped or damaged in any way.
�When the product exhibits a distinct change in performance –this indicates a need for
service.
16. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified personnel.
17. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electrical shock, or other hazards.
18. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
19. UPS / Surge Protection
A UPS is mandatory for efficient functioning of your Digital Watchdog unit.
When shipping the DW-Pro unit, the original
shipping carton packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray,
near the DW-Pro unit. Do not leave rubber or
plastic products in contact with the DW-Pro unit for
long periods of time. They will leave marks on the
finish.
The top and rear panels of the DW-Pro unit may
become warm after long periods of use. This is not
a malfunction.
Place the DW-Pro unit on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand.
When you place this DW-Pro unit next to a TV,
radio, or VCR, the playback picture may become
poor and the sound may be distorted. In this case,
place the DW-Pro unit away from the TV, radio, or
VCR.
Use a soft dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak
detergent solution, wring well and wipe. Use a dry
cloth to wipe it dry.Do not use any type of solvent,
such as thinner and benzene, as they may
damage the surface of the DW-Pro unit.
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
This DW-Pro unit is designed to last for long periods
of time. To keep your DW-Pro unit always
operational we recommend regular inspection
maintenance (cleaning parts or replacement). For
details contact your nearest dealer.
Moisture condensation damages the DW-Pro
unit. Please read the following carefully.
Moisture condensation occurs during the following
cases.
When you bring the DW-Pro unit directly from a
cold place to a warm place.
When you use the DW-Pro unit in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the
unit.
In the summer, when you use the DW-Pro unit in a
hot and humid place just after you move the unit
from an air conditioned room.
When you use the DW-Pro unit in a humid place.
Do not use the DW-Pro unit when moisture
condensation may occur.
If you use the DW-Pro unit in such a situation, it may
damage discs and internal parts. It is not
recommended to use the Digital Watchdog in a
location where moisture condensation may occur.

Please check to make sure the following equipment are included when you purchased DW-709/716. If any
items are missing, contact your dealer.
Equipment
Audio/Video
Connect Cable
Power Cable
Manual (Site/Center)
CD
(Manual / Center)
Monitor (Option)


Warranty Information
Kaltec Electronics (referred to as “the Warrantor”) warrants the Digital Video Recorder against
defects in materials or workmanship as follows:
LABOR: For a period of (1) year from the date of original purchase, if Digital Video Recorder is
determined to be defective, Kaltec will repair or replace the unit, with new or refurbished
product at its option, at no charge.
PARTS: In addition, Kaltec Electronics will supply replacement parts for a period of (1) year.
To obtain warranty or out of warranty service, please contact a Technical Support
Representative at 1-866-446-3595 Ext 242 Monday through Friday from 9:00 AM to 5:00 PM
Eastern.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of
the date of the original purchase is required before warranty service is rendered. This warranty
only covers failures due to defects in materials and workmanship which arise during normal
use. This warranty does not cover damage which occurs in shipment or failures which are
caused by products not supplied by the Warrantor or failures which result from accident,
misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation,
set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer
controls, improper operation, power line surge, improper voltage supply, lightning damage,
rental use of the product or service by anyone other than a Digital Video Recorder authorized
repair facility or damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above. THE WARRANTOR SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT
LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF THESE
PRODUCTS, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above exclusions or limitations may
not apply to you. This warranty gives you specific legal rights and you may also have other
rights that vary from state to state.
If the problem is not handled to your satisfaction, then write to the Address above.
SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORK-
MANSHIP AS DETERMINED BY THE WARRANTOR, IN ITS SOLEDISCRETION, ARE NOT
COV ERED. COSTS OF SUCH SERVICE CALLS ARE THE RESPONSIBILITY OF THE
PURCHASER.

CCoonntteennttss
Chapter 1. Guide
1. System Overview
1.1 Front panel ……………………………………………………………………3
1.2 Rear panel ……………………………………………………………………5
1.3 Description of the Remote Controller………………………………………9
2. Surveillance mode
2.1 Screen Layout …………………………………………………………………10
2.2 Enabing full screen & sequence modes……………………………………11
3. Menu operation
3.1 Using menu in live mode ……………………………………………………12
3.2 Using menu on PAN/TILT mode ……………………………………………13
3.3 Using menu on playback mode ……………………………………………14
4. Pan/Tilt Camera
4.1 Switching to Pan/Tilt control mode …………………………………………15
4.2 Pan/Tilt Camera Control………………………………………………………16
4.3 Supported Pan/Tilt Camera list………………………………………………17
5. Search
5.1 Accessing Search mode ……………………………………………………18
5.2 Search mode display …………………………………………………………18
5.2.1 Graph color display ………………………………………………………19
5.3 Selecting date and time ………………………………………………………20
5.3.1 Selecting date ……………………………………………………………20
CCoonntteennttss
5.3.2 Selecting cameras and changing graph bar line ……………………21
5.3.3 Audio Output………………………………………………………………22
5.3.4 Playback……………………………………………………………………23
6. Backup
6.1 Saving backup into local drive ………………………………………………24
6.1.1 Still image backup ………………………………………………………24
6.1.2 Video backup………………………………………………………………25
6.2 Saving backup using remote drive …………………………………………28
6.3 Printing still image ……………………………………………………………31
7. System Setup
7.1 Accessing Setup mode ………………………………………………………32
7.2 Setup menu ……………………………………………………………………32
7.3 System Setup …………………………………………………………………34
7.3.1 Password …………………………………………………………………34
7.3.2 Site Information……………………………………………………………35
7.3.3 Software Upgrade…………………………………………………………37
7.3.4 Log Information …………………………………………………………38
7.3.5 OSD / Dwell Time …………………………………………………………41
7.3.6 System management ……………………………………………………42
7.3.7 System Shutdown ………………………………………………………52
7.4 Recording Setup ………………………………………………………………54

7.4.1 Recording Setup …………………………………………………………54
7.4.2 Motion detection …………………………………………………………55
7.4.3 Motion Link setting ………………………………………………………56
7.4.4 Schedule……………………………………………………………………57
7.4.5 Quality/Resolution ………………………………………………………58
7.5 Camera Setup …………………………………………………………………59
7.5.1 Camera name ……………………………………………………………60
7.5.2 Sensor setting ……………………………………………………………61
7.5.3 Sensor/Control link ………………………………………………………62
7.5.4 Sensor/Camera link ………………………………………………………63
7.6 Network Setup…………………………………………………………………64
7.7 Backup Schedule ……………………………………………………………68
7.7.1 Adding Backup schedule ………………………………………………69
7.7.2 Deleting Backup schedule ………………………………………………74
8. Controls - Manual Control
8.1 Switching to Control Mode …………………………………………………75
Chapter 2. DVR Installation
1. Pan/Tilt Connection
2. Connecting LAN/PSTN Communication Lines
2.1 LAN, ISDN (with the Router), and Dedicated Line Connection …………80
CCoonntteennttss
2.2 PSTN (telephone line) Connection (optional) ……………………………81
3. RX Receiver (KRE-303) Connection Diagram (optional)
3.1 Name of Each Part and Description…………………………………………82
4. External Sensor Connection (Input)
5. Control Port Connection (Output)
6. Adding HDD
6.1 Installing new HDD ……………………………………………………………86
6.2 Checking HDD Database ……………………………………………………87
7. HDD Smart Check
7.1 HDD Smart Check ……………………………………………………………88
Appendix
1. Viewer for KDB data
2. Specifications
3. FAQ
4. Product Warranty

1. System Overview
2. Surveillance mode
3. Menu Operation
4. Pan/Tilt Camera
5. Search
6. Backup
7. System Setup
8. Controls - Manual Control
1. Guide

3
1. Guide
1. System Overview
System Overview
1. System Overview
[Figure 1-1. System front view]
[Directional Keys]
•Use to move through the menu options in Setup or Search mode.
•When controlling P/T/Z camera, press the directional keys to move the camera.
•When searching recorded image, you can adjust the size of the image using up and
down directional key.
[Enter Key]
•Use to select options in Setup or Search mode.
•Use to directly go to Control setup mode from the Surveillance mode.
[Jog(inner dial)]
•Rotate to view recordings, in Search mode, forwards or backwards one frame at a time.
•Rotate to change the value of options one unit at a time in Setup mode.
•When controlling P/T/Z camera, rotate to shift camera lens focus.
[Shuttle(outer dial)]
•Rotate to play the recordings, in Search mode, forward or backwards.
•Rotate to change the value of options continuously in Setup mode.
•When controlling P/T/Z camera, rotate to zoom in or out.
1.1 Front Panel
The following describes the keys and ports on the front of the system and their functions :
6 9 10 1 2 3 4 137 8
51211

5
1. Guide
1. System Overview
System Overview
4
1. Guide
1. System Overview
System Overview
[CD-RW Open]
•Press button to open CD-RW.
[Camera/Number keys]
•In Surveillance mode, press for full
screen display of that camera.
•In Search mode, press for full screen
display of that camera recording during
playback.
•Press the keys to enter correct numeric
password when accessing Setup or
Search modes.
[Auto]
•Press to begin automatic channel
sequence either in full or multi screen
modes.
[Split screen buttons]
•In Surveillance or Search modes, press
to select 4-splitscreen , 9-splitscreen
or 16-splitscreen (DW-716).
[Menu]
•Press to access Setup mode.
[Search]
•Press to access Search mode.
[Search mode control Keys]
•In Search mode, use these keys to view
the recording from either the first or last
recorded image, to play the recording
either forwards or backwards, to pause
viewing the recording.
[USB Port]
•You can connect a portable disk drive to
USB port to save backup of recorded
video.
•You can update your system software
with an upgrade package through the
USB port.
•A standard HP PostScript computer
printer can be connected to USB port of
DW-709/716 to print out any still image.
�Removable Disk support
[POWER LED]
•When power switch is on, the LED gives
green light.
[Power Connector]
•Power cable input, 110V ~ 220V, for system
main power Supply.
[Camera Video Input BNC]
•16 BNCs for DW-716 and 9BNCs for DW-
709.
[Loop Through Output]
•Video output ports for camera loop through
to view image to another monitor or device.
•The system supports both NTSC and PAL.
1.2 Rear panel
[Caution]
Be careful of electrocution. Please
read [Safety Warnings and Cautions]
[Caution]
Dependant on the grounding status of
the power supply electric current that
can cause an electric shock may flow
in the video line (coaxial cable). Turn
off the system before connecting the
video line to the BNC port.
☞[Note] Removable Disk
The table below lists compatible USB
disks. If you want to use other removable
disk, it should be compatible with Linux
2.4.0 or over. Other USB disk may not
work properly.
It is recommended that you confirm
through the manufacturer the Linux
compatibility of the removal disk you wish
to purchase.
No. Name Company USB Version
1 AnyDrive AL-tech Ver 1.1
2 Unidrive KMIT Ver 1.1
3 Nexdrive JUNGSOFT Ver 1.1
4 SHELLGINO N4 SHELLGINO Ver 1.1
5 TRANSCEND JF A 128M Transcend Ver 1.1
The following describes keys and ports on the rear part of the system and their functions
(DW-716) :
[Figure 1-2. System rear view]
1
14
7915 11 812 13 6 4 5 16 1
2 3
10

7
1. Guide
1. System Overview
System Overview
6
1. Guide
1. System Overview
System Overview
[RS-422 Output Port for P/T/Z Control]
•RS-422/RS-485 output for controlling P/T/Z cameras.
[Video Output Port]
•Video output for connecting with CVBS monitor.
•Supports both NTSC and PAL video format depending on the input.
[VGA Output Port]
•VGA output for connecting with CRT VGA monitor.
[S-Video Output Port]
•S-Video output for connecting with SVGA monitor.
•Supports both NTSC and PAL video format depending on the input.
[Audio In]
•Audio input for recording .
(For audio recording, it is recommended to use any microphone with an amplifier. A
microphone without amplifier may not record audio well enough if the audio input
singnal is too low.)
[Sensor Input Port]
•External sensor inputs for channels 1~4.
•The system supports NC and NO sensor types.
[Control Output Port]
•Control output for connecting control devices for channels 1~4.
[Audio Out]
•Replay of recorded Audio.
[External modem terminal] NOT AVAILABLE IN EUROPEAN MODELS
•Provide a connection to the external modem for a remote access.
[LAN]
•Ethernet 10/100 connection port for connecting the system through network.
[Cooling Fan]
•Cooling fan for system ventilation.
[Mouse]
•Input for using a mouse with the system.
•If the mouse has a scroll wheel, the wheel can be used as system’s jog/shuttle dial.
•Applicable Wheel Mouse List
[Caution]
Since control devices use output in a contact point format without polarity at the control
output port, do not connect AC 110V ~ 220V of the power cable or supply DC power.
When controlling DC power, it is recommended that you cut the (-ve) line.
No. Mouse Name Model Name or Support wheel Place of Manufacture Remarks
Type feature
1 SOLID YEAR SYW1320SOLIDYEAR YES China
2 A4TECH SWW-35 YES China
3 SAMSUNG SMP2000WX YES CHIC TECH/China
4 TriGem M-S48a YES Logitech(China)
☞[Note] Support for Scroll Mouse
•The scroll mouse types supported by the system are listed in the table below.
Scroll mouse types other than those listed below may not be supported by the system .
Please check.

9
1. Guide
1. System Overview
System Overview
8
1. Guide
1. System Overview
System Overview
1.3 Description of the Remote Controller
Below picture shows the description of each feature in remote control. All the feature is same
with the front buttons in the system.
☞[Notice]
•To select a camera from 10 to 16 press
first. And press among ~ .
MENU
SEARCH
Number
AUTO
Dot
Delete
Shuttle(+)
Shuttle(-)
Arrow key
Enter
Jog(+)
Jog(-)
Playback
Screen division
[IMAGE INPUT/OUTPUT SWITCH]
•Image Input/Output terminal options
•NTSC,PAL : Default settings for input video format.
•CVBS, VGA : Image output types; when CVBS is selected, the image will be displayed on the
external monitors; when VGA is selected, the image will be displayed on the computer
monitors.
(but, when monitor is selected as an image output, it take about 1 minute after power
connection to view the image on the VGA monitor. Be sure to wait until the processing
window appears.)

1. Guide1. Guide
10
2. Surveillance Mode
Surveillance M ode
2. Surveillance Mode
2.1 Screen Layout
[Figure 2-1. Main Surveillance Mode by 4 split screen]
[Table 2-1. Available Recording Modes and Screen Display]
 
C : Continuous Recording
M : Motion Recording
S : Sensor Recording
P : Pre-alarm Recording
No recording
Continuous Recording
Motion Recording
Sensor Recording
Motion & Sensor Recording
Motion & Pre-alarm Recording
Sensor & Pre-alarm Recording
Motion & Sensor & Pre-alarm Recording
No Display
Red REC
Orange REC
[Camera Number]
•Displays camera number.
[Camera Name]
•Displays camera name.
[Recording Status]
•Displays camera recording mode enabled.
[P/T/Z Status]
•Displays Pan/Tilt camera status enabled.
[Audio Recording Status]
•Shows audio recording enabled.
2
3
4
5
1
2. Surveillance Mode
11
2. Surveillance Mode
Surveillance M ode
[To Select Full Screen mode]
•Press any key 1~16 on the system to enlarge
that camera channel and view in full screen.
[To Select Quad screen]
•Press the 4-split screen button to select quad
display of cameras 1-4. Press again to move to
next quad screen.
[To Select 9 way split screen]
•Press the 9-split screen button to select display
of cameras 1-9. Press again to move to next 9
way screen.
[To Select 16 way split screen]
•Press the 16 way split screen button to view all
cameras on one screen (DW-716).
[Sequence]
•When full screen is selected, press the Auto key
to view all camera channels in sequence. The
system will also sequence between quad and 9
way displays. (see page 41 - OSD/Dwell Time
for details on changing Auto option).
2.2 Enabling full screen and sequence modes
[Figure 2-2. 16-splitscreen mode]
[Figure 2-3. 9-splitscreen mode]
[Figure 2-4. Full screen mode]

12
1. Guide
13
1. Guide
M enu Operation
M enu Operation
3. Menu Operation
3.1 Using menu in live mode
Pop-up menu appears when you click right mouse button on surveillance, search or
Pan/Tilt mode
[MENU]
•Main menu for system setup
•When using mouse, click on 'Menu' icon to
go to Setup.
•When using front panel, press 'MENU'
button on the front panel.
[SEARCH]
•Click on "SEARCH" to go to Search mode.
•When using front panel, press "SEARCH"
button.
[CONTROL]
•Click on "CONTROL" to go to Control
menu.
•When using front panel, press "OK"
button.
[AUTO]
•To go to auto display mode, select single,
quad or 9 channel split screen.
•Press auto display icon to get auto rotation
screen. Click to view live image in single,
quad, 9ch, and 16ch modes. (See page 41 to
setup the dwell time as you wish)
[Multi Screen]
•You can get 4, 9 or 16(DW-716 only)
channel display screen with clicking the
icon by mouse or pressing the front panel
key.
[Figure 3-1. Pop-up menu operated by mouse on surveillance mode]
☞[Notice] Right mouse click
Click right mouse button to activate or
deactivate pop-up menu in the surveill
ance mode.
Clicking right mouse button anywhere in
the setup mode will return to sub-menu
screen.
3.2 Using menu on PAN/TILT mode
This menu appears by selecting a full channel that supports P/T camera in surveillance
mode.
[PTZ]
•Button to go to Pan/Tilt control mode.
•Select any channel that supports Pan/Tilt
camera. If you click right mouse button on
the image, it changes to full screen.
[Pan/Tilt]
•Controls the Pan/Tilt camera in Pan/Tilt
mode
[ZOOM IN/OUT]
•Zoom in or out any supported Pan/Tilt or
Speed Dome type camera.
[FOCUS IN / OUT]
•Adjust focus of the camera lens.
(This function is not supported on any
auto focus cameras)
[Figure 3-2. Pop-up menu on Pan/Tilt mode
☞[Notice] Right mouse click
Use right mouse click to enter into or exit
from the Pop-up menu.
3. Menu Operation
3. Menu Operation
234 5
1234 1

15
1. Guide
4. Pan/Tilt Camera
Pan/Tilt Cam era
14
1. Guide
3. Menu Operation
M enu Operation
4. Pan/Tilt Camera
4.1 Switching to Pan/Tilt control mode
[Pan/Tilt Camera Control]
•Select the camera channel connected to the
P/T/Z camera by using the mouse or
camera number keys on the front panel. This
will display the channel in full screen mode.
•Once the channel is enlarged, press [Enter] to
access [P/T/Z control mode]. Pan/Tilt
controls may differ depending on the
connected camera model.
[Exiting P/T/Z control mode]
•When you have finished with this screen,
click [OK] button by mouse or press MENU
on the front panel to return to Surveillance
mode.
[Figure 4-1. Enlarged P/T/Z channel]
[Figure 4-2. P/T/Z control mode]
3.3 Using menu on playback mode
Click this button to select time and date to
search.
Click this button to start backup.
(Refer to page 24 for details of backup
procedure)
[Playback button]
•(From the left) First recorded image / play
backward / pause / play forward / Last
recorded image
(See page 23 Table for details)
[Direction Key]
•Using left and right arrow key, you can
play backward or forward on frame by
frame rate.
•Using up and down arrow key, you can
increase or decrease the size of playback
image.
[Figure 3-3. Mouse pop-up menu on multiple
channel playback screen(DW-716)]
[Figure 3-4. Mouse pop-up menu on single
channel playback screen]
This menu appears only when you click right mouse button while playing back recorded images.
( See page 23 for how to playback of recorded images. )
3
4
2
1