Kärcher NT 14/1 User manual

English 5.906-492.0 Rev. 00 (12/10) 1
NT 14/1
Service Manual

2 English 5.906-492.0 Rev. 00 (12/10)
1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Hazard levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Technical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4 Parts of the system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.1 NT 14/1 Eco Te and Advanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.2 NT 14/1 Classic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2.1 Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2.2 Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2.3 Type plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Basic settings and service procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.1 Replace the chassis lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.2 Replace the suction support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.3 Remove the suction head hood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4 Install the suction head hood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.5 Replace the circuit board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.5.1 NT 14/1 Eco Te and Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.5.2 NT 14/1 Classic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6 Replacing the mains cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6.1 NT 14/1 Eco Te and Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6.2 NT 14/1 Classic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.7 Replace the electrodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.8 Replacing the suction turbine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.9 Filter dedusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.10 Replace the handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Maintenance and care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 Exchanging the flat pleated filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.2 Cleaning the electrodes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.1 Suction turbine does not run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2 Suction turbine turns off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.3 Suction turbine does not start again after the container has been emptied . . 13
7.4 Suction capacity decreases. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.5 Dust comes out while vacuuming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.6 Automatic shut-off (wet vacuum cleaning) does not react. . . . . . . . . . . . . . . . 13
7.7 Semi-automatic filter dedusting does not work . . . . . . . . . . . . . . . . . . . . . . . . 13
7.8 Semi-automatic filter dedusting does not shut off . . . . . . . . . . . . . . . . . . . . . . 13
7.9 Semi-automatic filter dedusting cannot be switched on . . . . . . . . . . . . . . . . . 13
8 Technical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.1 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.2 Tightening torques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9 Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

English 5.906-492.0 Rev. 00 (12/10) 3
Good service work requires extensive and practice-
oriented training as well as well-structured training
materials.
Hence we offer regular basic and advanced training
programmes covering the entire product range for all
service engineers.
In addition to this, we also prepare service manuals
for important appliances - these can be initially used
as instruction guides and later on as reference
guides.
Apart from this, we also regular information about
product enhancements and their servicing.
If you should require supplements, have corrections
or questions regarding this document, please ad-
dress these citing the following subject to:
[email protected]
The responsible product specialist will take care of
your issue.
Copyingandduplication oftextsanddiagramsas
well as third-party access to this information is
permitted only with the explicit permission of the
company:
Alfred Kärcher GmbH & Co. KG
P O Box 160
D -71349 Winnenden
www.kaercher.com
Danger
Immediate danger that can cause severe injury or
even death.
몇Warning
Possible hazardous situation that could lead to se-
vere injury or even death.
Caution
Possible hazardous situation that could lead to mild
injury to persons or damage to property.
Structure:
–Filter dedusting
(Eco Te and Advanced only)
–The suction unit can be removed to clean hard to
reach areas.
–Handle (Advanced only)
–Socket (Eco Te only)
–Rotating cable hooks for cable coiling.
(Eco Te and Advanced only)
–Intake for suction hose and elbow.
–Storageforsuction pipesandcrevicenozzle inthe
chassis.
(Eco Te and Advanced only)
–In addition to the main filter, a filter bag may be
used.
–Intake for Systainer possible with the optional
adapter plate (2.641-982.0).
1 Preface
Subject: Fall 108985
2 Safety instructions
2.1 Hazard levels
3 Technical Features

4 English 5.906-492.0 Rev. 00 (12/10)
1 Flat fold filter
2 Suction hose
3 Cable hook, rotating
4 Handle
5 Suction head lock
6 Impeller
7 Chassis
8 Filter dedusting
9 Steering roller
10Dirt receptacle
11Suction support
12Chassis lock
13Floor nozzle
14Indicator lamp
15Socket
16Power switch
17Suction pipe
18Carrying handle
19Suction head
20Bender
21Suction pipe storage
22Elbow intake
23Crevice nozzle storage
24Exhaust filter
25Power cord
4 Parts of the system
4.1 NT 14/1 Eco Te and Advanced
1
2
3
4
5
6
7
17
16
15
14
13
20
11 10
21
24 25
23
22
18 19
12 9 8

English 5.906-492.0 Rev. 00 (12/10) 5
1 Filter cover
2 Suction head lock
3 Dirt receptacle
4 Impeller
5 Guiding roll with fixed position brake
6 Steering roller
7 Suction support
8 Suction head
9 Power switch
10Carrying handle
4.2 NT 14/1 Classic
4.2.1 Front view

6 English 5.906-492.0 Rev. 00 (12/10)
1 Suction tube 550 mm
2 Nameplate
3 Exhaust filter
4 Floor nozzle
5 Power cord
6 Pickup for floor nozzle
7 Intake for suction pipe
8 Suction tube 550 mm
The type plate is located on the rear of the appliance.
4.2.2 Rear view
4.2.3 Type plate

English 5.906-492.0 Rev. 00 (12/10) 7
1 Chassis
2 Chassis lock
Undo the lock (see arrow).
Pull out the lock.
Replace the lock.
Replace the pressure spring if necessary.
1 Dirt receptacle
2 Bolt (electrically conductive)
3 Suction support
Replace the suction support.
5 Basic settings and service procedures
5.1 Replace the chassis lock
2
1
5.2 Replace the suction support
2
31

8 English 5.906-492.0 Rev. 00 (12/10)
1 Support
2 Fastening screws for cable intake
3 Fastening screws for hood
4 Fastening screw for carrying handle
5 Carrying handle
6 hood
7 Filter cover
8 Device switch button
Unscrew the fastening screws for the carrying
handle.
Remove the carrying handle.
Remove the device switch button.
Remove the filter cover.
Unscrew the fastening screws for the cable intake.
(Eco Te and Advanced only)
Remove the holders.
Unscrew the fastening screws for the hood.
Remove the hood.
1 Filter cover
2 Suction head casing
3 Power switch
4 Pressure spring
5 Device switch button
1 hood
2 Socket casing
Note: During the installation of the hood, make sure
that the guides of the socket casing (see arrows) and
the hood engage.
Remove the flat fold filter before installing the
hood.
5.3 Remove the suction head hood
1
2
2
56 444
3
3
3
8
7
5.4 Install the suction head hood
1345 2
12

English 5.906-492.0 Rev. 00 (12/10) 9
1 Exhaust filter
2 Fastening screws for turbine housing
3 Power cord
4 Power switch
5 Control chip
6 Suction turbine
7 Turbine casing
8 Cord grip
1 Fastening screw for socket casing
Remove the fastening screw for socket casing.
1 Power cord
2 Ferrit ring (anti-interference ring)
3 Power switch
4 Control chip
Pull the circuit board out toward the top.
1 Power switch
2 Micro switch
3 Socket casing
4 Socket
5 Indicator lamp
6 Control chip
Remove the socket casing.
Disconnect all connecting cables from the circuit
board.
Replace the circuit board.
Connect the new circuit board as per the circuit di-
agram.
Install circuit board and the socket casing in re-
verse sequence.
5.5 Replace the circuit board
5.5.1 NT 14/1 Eco Te and Advanced
1
3
4
5
2
6
2
7
8
1
2
4
3
1
3
1
2
456

10 English 5.906-492.0 Rev. 00 (12/10)
1 Exhaust filter
2 Fastening screws for turbine housing
3 Power cord
4 Ferrit ring (anti-interference ring)
5 Power switch
6 Control chip
7 Suction turbine
8 Turbine casing
9 Cord grip
1 Control chip
2 Connecting cable, electrode overflow fuse
3 Connecting cable, suction turbine
4 Connecting cable, appliance switch
Disconnect all connecting cables from the circuit
board.
Remove the control printed circuit board from
holder.
Replace the circuit board.
Connect the new circuit board as per the circuit di-
agram.
Insert the control printed circuit board into the
holder.
1 Ferrit ring (anti-interference ring)
2 Neutral conductor
3 Phase
4 Ground cable (protective conductor)
Unscrew the ground cable (protective conductor)
from the socket.
Disconnect the phase and the neutral connector
on the device switch.
Remove the clamp for mains cable.
Remove the mains cable from the cable guide.
Install the new mains cable in reverse sequence.
5.5.2 NT 14/1 Classic
5.6 Replacing the mains cable
5.6.1 NT 14/1 Eco Te and Advanced
3
4
12

English 5.906-492.0 Rev. 00 (12/10) 11
1 Power cord
2 Ferrit ring (anti-interference ring)
3 Power switch
4 Cord grip
Remove the traction relief.
Remove the mains cable from the cable guide.
Pull the mains cable out of the appliance switch.
Install the new mains cable in reverse sequence.
1 Electrodes
2 Connecting cable for electrodes
3 Control chip
Disconnect the connecting cables from the circuit
board and the electrodes.
Replace damaged connecting cables.
Replace the electrodes.
Install new connecting cables in reverse se-
quence.
Note: The connecting cable must be routed as
shown in the illustration within the respective pins.
5.6.2 NT 14/1 Classic 5.7 Replace the electrodes
12
21
3

12 English 5.906-492.0 Rev. 00 (12/10)
Unscrew the fastening screws for the turbine cas-
ing.
1 Top part of the turbine casing
2 Sound proofing
3 Connection plug of the turbine
4 Suction turbine
5 Bottom part of the turbine casing
6 Air channel
7 Seal
Disassemble turbine casing.
Pull the connection plug off the turbine.
Remove the suction turbine.
Place the suction turbine onto the seal of bottom
part of the turbine casing (see arrow).
1 Connection plug of the turbine
2 Suction turbine
Align the new suction turbine as per the marking
arrows.
Connect the connection plug of the turbine.
Install the turbine casing in the reverse sequence.
1 Sliding part
2 Base plate
3 Button for filter shake off system
4 Pressure spring
1 Fastening screw
2 Disc
3 Brake bracket
4 Pressure spring
5 Handle
Unscrew locking screws.
Remove the disc.
Remove the handle.
Replace the brake bracket if necessary.
Replace the pressure spring if necessary.
Install the new handle in reverse sequence.
5.8 Replacing the suction turbine
4
7
6
1
2
53
3
1
1
2
5.9 Filter dedusting
5.10 Replace the handle
2
14
3
1
4 33 4
5
2

English 5.906-492.0 Rev. 00 (12/10) 13
몇Warning
First remove the mains plug before doing any job on
the vacuum cleaner.
Open filter door.
Replace the flat pleated filter.
Close the filter door, it must lock into place.
Release and remove the suction head.
Clean the electrodes.
Insert and lock the suction head.
Check cables, plugs, fuse, socket and electrodes.
Turn on the appliance.
Empty the container.
Turn off the appliance and wait for 5 seconds, turn
it on again after 5 seconds.
Check/clean the electrode overflow fuse.
Remove blockages in the suction nozzle, suction
tube, suction hose, or flat pleated filter.
Replace the paper or fleece filter bag.
Press the semi-automatic filter dedusting key five
times.
Ensure the filter cover properly locks into place.
Replace the flat pleated filter.
Check for proper installation of the flat pleated fil-
ter.
Ensure the filter cover properly locks into place.
Replace the flat pleated filter.
Check/clean the electrode overflow fuse.
Continuously check the filling level in case of non-
conductive liquid.
Suction hose is not connected.
Inform Customer Service
Inform Customer Service
6 Maintenance and care
6.1 Exchanging the flat pleated filter
6.2 Cleaning the electrodes
1
2
7 Troubleshooting
7.1 Suction turbine does not run
7.2 Suction turbine turns off
7.3 Suction turbine does not start again af-
ter the container has been emptied
7.4 Suction capacity decreases
7.5 Dust comes out while vacuuming
7.6 Automatic shut-off (wet vacuum clean-
ing) does not react
7.7 Semi-automatic filter dedusting does
not work
7.8 Semi-automatic filter dedusting does
not shut off
7.9 Semi-automatic filter dedusting cannot
be switched on

14 English 5.906-492.0 Rev. 00 (12/10)
The status of the attached circuit diagram represents
the creation date of the service manual. This circuit
diagramis notupdated. Whenworking onthe device,
please always use the current circuit diagram in
Kärcher-Inside.
There are no special tools necessary.
No data.
8 Technical specifications
Appliance type Appliance
no.: Circuit dia- gram Operating in- structions Spare parts list
NT 14/1 Classic *EU, 220-240 V, 1~
50/60 Hz 1.510-107.0 0.089-158.0 5.963-530.0 5.971-130.0
NT 14/1 Classic *CH, 220-240 V, 1~
50/60 Hz 1.510-115.0 0.089-158.0 5.963-530.0 5.971-130.0
NT 14/1 Classic *GB, 220-240 V, 1~
50/60 Hz 1.510-116.0 0.089-158.0 5.963-530.0 5.971-130.0
NT 14/1 Eco *EU, 220-240 V, 1~ 50/60
Hz 1.510-100.0 0.089-158.0 5.963-211.0 5.971-013.0
NT14/1 Eco *CH,220-240 V, 1~50/60
Hz 1.510-101.0 0.089-158.0 5.962-211.0 5.971-013.0
NT14/1 Eco *GB,220-240 V, 1~50/60
Hz 1.510-102.0 0.089-158.0 5.963-211.0 5.971-013.0
NT 14/1 Eco *CUL, 120 V, 1~ 60 Hz 1.510-103.0 0.089-158.0 5.963-417.0 5.971-086.0
NT 14/1 Eco *JP, 100 V, 1~ 50/60 Hz 1.510-104.0 0.089-158.0 5.963-427.0 5.971-095.0
NT 14/1 Eco Advanced *EU, 220-240
V, 1~ 50/60 Hz 1.510-105.0 0.089-158.0 5.963-063.0 5.970-983.0
NT 14/1 Eco Te Advanced *EU, 220-
240 V, 1~ 50/60 Hz 1.510-106.0 0.089-158.0 5.963-063.0 5.970-983.0
NT 14/1 Eco Te Advanced *CH, 220-
240 V, 1~ 50/60 Hz 1.510-108.0 0.089-158.0 5.963-063.0 5.970-984.0
NT 14/1 Eco Te Advanced *GB, 220-
240 V, 1~ 50/60 Hz 1.510-109.0 0.089-158.0 5.963-063.0 5.970-984.0
NT 14/1 Eco Advanced *CH, 220-240
V, 1~ 50/60 Hz 1.510-111.0 0.089-158.0 5.963-063.0 5.970-983.0
NT 14/1 Eco Advanced *GB, 220-240
V, 1~ 50/60 Hz 1.510-112.0 0.089-158.0 5.963-063.0 5.970-983.0
8.1 Special tools
8.2 Tightening torques

English 5.906-492.0 Rev. 00 (12/10) 15
9 Circuit diagram
1
23456789
10
11
12 13
N
L1
PE
-DS1
PEPEPE
fma
2031399
b
1
SMD-W
5181379
SLP
02
2009-12-01
b
B1 DS1 M1 N1 S1 S2 X1 X2
ELEKTRODEN SAUGTURBINE HAUPTSCHALTER LEUCHTDIODE STEUERELEKTRONIK UMSCHALTER-BETRIEBSART NETZSTECKER STECKDOSE TE
B1 DS1 M1 N1 S1 S2 X1 X2
ELECTRODES VACUUM MOTOR MAINSWITCH LIGHT EMITTING DIODE SWITCH ELECTRONIC UNIT CHANGE OVER SWITCH OPERATING MODE POWER SUPPLY PLUG PLUG SOCKET TE
B1 DS1 M1 N1 S1 S2 X1 X2
ÉLECTRODES TURBINE D´ASPIRATION INTERRUPTEUR PRINCIPAL DIODE ÉLECTROLUMINESCENTE UNITÉ ÉLECTRONIQUE DE COMMANDE COMMUTATEUR MODE D´EXPLOITATION PRISE D´ALIMENTATION D´ÉNERGIE PRISE DE COURANT
TE
B1 DS1 M1 N1 S1 S2 X1 X2
ELECTRODOS FOTODIODO TURBINA DE ASPIRACIÓN SISTEMA ELECTRÓNICO INTERRUPTOR PRINCIPAL INTERRUPTOR MODO OPERATIVO ENCHUFE DE SUMINISTRO DE ENERGIA TOMA DE CORRIENTE
TE
*
nur bei Variante TE only for variant TE seulement pour la variante TE
solamente para la variante TE
D
GB
F E
X1
*
S1
100V 1~ 50/60Hz 230/240V 1~ 50/60Hz
X3X2
N1
X12 X13 X15 X14
****
X5 X6
X1
X4X7X8X9
X11
X10
B1
M
1~
M1
1
24
S2
*
Erdung: Saugstutzen Grounding: Suction nipple Mise à la terre: Tubulure d´aspiration Toma de tierra: tubuladura de aspiración
X2
*
***
BRAUN BROWN BRUN GRÜN/GELB GREEN/YELLOW VERT/JAUNE MARRÓN BLAU BLUE BLEU AZUL VERDE/AMARILLO
X1
GB
ANLAGE
plant
installat. AUFTRAG order no. order no.
ORT
location lieu
BENENNUNG identication identication ANLAG.-BEZ. plant desig. denomin.
Stromlaufplan circuit diagram
plan de circuit
NT 14/1
ZEICHNUNGS-NR.
drawing-no.
Dessin No.
BLATT page page
BLATTZ. page tot. page tot.
2010-07-05
Datum
date date
ANZ.
no. no.
Ä-IND.
ch.-ind. ch.-ind.
NORM
stand. stand.
GEPR. check
vérif.
GEZ.
draft
dessin.
File:
NT14_1
ura
1
2
0.089-158
=SLP +S
Winnenden
ÄND./FR.
change/rel. change/rel.
ERS.F.
exch. of
rempl.
Dokument document
Dok-Vers.
doc-vers. doc-vers.
Dok-Nr.
doc-no. doc-no.

16 English 5.906-492.0 Rev. 00 (12/10)
1
23456789
10
11
12 13
N
L1
PE
PEPEPEPEPEPEPEPEPE
-DS1
fma
2031399
00
SMD-W
5181379
SLP
00
B1 DS1 M1 N1 S1 S2 X1 X2
ELEKTRODEN SAUGTURBINE HAUPTSCHALTER LEUCHTDIODE STEUERELEKTRONIK UMSCHALTER-BETRIEBSART NETZSTECKER STECKDOSE TE
B1 DS1 M1 N1 S1 S2 X1 X2
ELECTRODES VACUUM MOTOR MAINSWITCH LIGHT EMITTING DIODE SWITCH ELECTRONIC UNIT CHANGE OVER SWITCH OPERATING MODE POWER SUPPLY PLUG PLUG SOCKET TE
B1 DS1 M1 N1 S1 S2 X1 X2
ÉLECTRODES TURBINE D´ASPIRATION INTERRUPTEUR PRINCIPAL DIODE ÉLECTROLUMINESCENTE UNITÉ ÉLECTRONIQUE DE COMMANDE COMMUTATEUR MODE D´EXPLOITATION PRISE D´ALIMENTATION D´ÉNERGIE PRISE DE COURANT
TE
B1 DS1 M1 N1 S1 S2 X1 X2
ELECTRODOS FOTODIODO TURBINA DE ASPIRACIÓN SISTEMA ELECTRÓNICO INTERRUPTOR PRINCIPAL INTERRUPTOR MODO OPERATIVO ENCHUFE DE SUMINISTRO DE ENERGIA TOMA DE CORRIENTE
TE
*
nur bei Variante TE only for variant TE seulement pour la variante TE
solamente para la variante TE
D
GB
F E
white / neutral
X1
black / phase
*
X3X2
white / neutral
black / phase
S1
X12 X13 X15 X14
****
N1
X11
X10
white / neutral
black / phase
X2
*
B1
M
1~
M1
X5 X6
X1
X4
X1
***
white
neutral
black Phase
protective
conductor
120V 1~ 50/60Hz
white / neutral
Phase / black
green (yellow)
1
24
S2
*
X7X8X9
Erdung: Saugstutzen
Grounding: Suction nipple Mise à la terre: Tubulure d´aspiration
Toma de tierra: tubuladura de aspiración
ANLAGE
plant
installat. AUFTRAG order no. order no.
ORT
location lieu
BENENNUNG identication identication ANLAG.-BEZ. plant desig. denomin.
Stromlaufplan circuit diagram
plan de circuit
NT 14/1
ZEICHNUNGS-NR.
drawing-no.
Dessin No.
BLATT page page
BLATTZ. page tot. page tot.
2010-07-05
Datum
date date
ANZ.
no. no.
Ä-IND.
ch.-ind. ch.-ind.
NORM
stand. stand.
GEPR. check
vérif.
GEZ.
draft
dessin.
File:
NT14_1
ura
22
0.089-158
=SLP +S
Winnenden
ÄND./FR.
change/rel. change/rel.
ERS.F.
exch. of
rempl.
Dokument document
Dok-Vers.
doc-vers. doc-vers.
Dok-Nr.
doc-no. doc-no.