Kathrein UFS 946/CI+ User manual

Operating Instructions Part 2 UFS 946/CI+
Basic functions and operation Englisch
Receivers Part no. Operating instructions valid as of software version:
UFS 946/CI+ 20210222 1.00

2
Dear customer,
these operating instructions are intended to help you make the fullest use of the extensive range of
functions offered by your new receiver.
We have tried to make the operating instructions as easy as possible to understand, and to keep them as
concise as possible. To help you understand particular specialist terms that cannot be translated, we have
added a short glossary at the end of the operating instructions.
The power switch and auto standby function (see Safety Instructions - Important Information) are
environmentally friendly features. If you will not be using your receiver for an extended period, you should
use the on/off switch to disconnect it from the power supply and save energy. For shorter breaks, you can
use the remote control to switch the receiver to standby, which uses only a minimal amount of energy.
We hope your reception will always be brilliant and you will enjoy using your new HDTV receiver.
Your
KATHREIN team
Preface
Note on Audio MPEG Inc. and S.I.SV.EL, S.P.A:
This unit makes use of legally protected technologies, which are protected by patents in the USA and also
by other intellectual property rights in other countries.
KATHREIN-Werke KG has obtained licences from Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo
dell‘elettronica, S.I.SV.EL, S.P.A to use these technologies. These licences carry certain restrictions which
also apply to you as the customer. Accordingly this unit may only be used by the end customer for private
non-commercial purposes and for the licensed content. It may not be used for commercial purposes.
The use of products or processes that are sold or used with this unit is not included in this statement.
The use of reverse engineering is not permitted in respect of the licensed technologies, nor is disassembly.
Note on DiSEqC™:
The term DiSEqC™ used in these operating instructions is a registered trade mark of the European
Telecommunication Satellite Organisation (EUTELSAT).
Note on Macrovision:
The product is equipped with copyright technology, which is protected by patents in the USA and by
other intellectual rights of the Rovi Corporation. Use of reverse engineering or disassembly is prohibited.
Legal information

3
Legal information
Manufactured under licence from Dolby Laboratories. “Dolby” and the double-D
symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and in
other countries.
®
CI+ and the CI+ logo are trade marks or registered trade marks of CI Plus LLP.
The UFS 946/CI+ satisfies the minimum requirements of CI+.
YouTube™ and the YouTube logo are trademarks or registered trademarks of
YouTube, LLC.
SHOUTcast™Radio and the SHOUTcast™Radio logo are trademarks or
registered trademarks of Nullsoft Inc.
Please note that the receiver's functions for viewing, CI+ encrypted channels may be restricted
because of CI+ requirements.
Software changes/use of applications
Any modifications to the receiver software, or the use of applications not provided by Kathrein will
invalidate the warranty! You will have to bear the costs yourself for shipping and repairing any receiver
that requires attention due to modifications to the software and use of applications other than those
provided by Kathrein!
For this reason, you should only use software and applications provided by Kathrein for your receiver.
These are available to download from the satellite or from our Internet pages (www.kathrein.de).
Kathrein assumes no liability for the loss of recordings/data on internal hard disks or external storage
media.
The software installed on the device/product before dispatch from the factory is suitable for its function
and is of the quality usual for this type of software. It has not been technically possible to fully eliminate
all bugs during the software development process. However the software as delivered is defective
only if it fails to perform the functions usual for the device/product. A shortcoming that causes only an
insignificant reduction in quality does not rank as a defect. Functional shortcomings in the software or
program that result from hardware defects, ambient conditions, incorrect operation or the like do not rank as
software defects.
Included in the software for this receiver is software that is licensed under the GNU (General Public
Licence). The source code of the program is available at: www.kathrein.de/linux/receiver/ufs946

4
List of contents
Preface......................................................................... 2
Legal information ....................................................... 2
List of contents........................................................... 4
Safety instructions - important notes....................... 6
Basic functions......................................................... 10
Remote control in live mode (TV/radio) ................... 11
I want to watch TV ... ............................................... 12
I want to listen to the radio ...................................... 13
I want to access teletext .......................................... 14
Editing and selection options in the menus.............. 15
Alphanumeric entries............................................... 16
Switching between TV and Radio operation............ 18
Adjusting the volume................................................ 18
Channel selection .................................................... 18
... directly ........................................................................... 18
... from the channel list....................................................... 18
Channel banners (information) ................................ 21
Calling up the channel options................................. 23
Audio selection......................................................... 24
Select subtitle........................................................... 25
Teletext..................................................................... 26
Electronic Programme Guide (EPG)....................... 27
General information on the programme guide......... 27
Calling up the EPG .................................................. 28
Navigation (remote control buttons in the EPG) ...... 29
EPG views ............................................................... 30
“Current” view.................................................................... 30
“Preview” view (programme magazine)............................. 31
Categories view................................................................. 32
Search function........................................................ 33
More episodes................................................................... 33
Key word search in detailed information............................ 34
Full-text search.................................................................. 35
Extras menu............................................................. 36
My hints ............................................................................. 36
HbbTV........................................................................ 37
Kathrein portal (Media centre)................................. 38
Mainmenu.................................................................. 39
Calling up the main menu and introduction.............. 39
Overview of the main menu submenus.................... 40
Mainmenu - Edit TV-Channellist.............................. 41
Calling up the menu................................................. 41
Navigation (remote control buttons in
“Edit TV-Channellist” menu)..................................... 43
Views (sort orders)................................................... 44
Selection of the channel/s to be edited.................... 45
Edit channels (channel lists).................................... 45
Move.................................................................................. 46
Delete ................................................................................ 46
Skip.................................................................................... 46
Lock................................................................................... 47
To Favourite....................................................................... 47
Start Blockselection........................................................... 48
Editing favourites lists.............................................. 49
Move.................................................................................. 49
Remove from favoritelist.................................................... 49
Lock................................................................................... 49
Start Blockselection........................................................... 49
Rename favoritelist............................................................ 50
Mainmenu - Channel Search ................................... 51
Calling up the menu................................................. 51
Automatic channel search........................................ 52
Manual channel search............................................ 54
Channel scan with service ID................................... 56
ASTRA channellist management (LCN)................... 57
Use ASTRA channellist...................................................... 57
Update ASTRA channel list................................................ 58
Reset ASTRA channel list.................................................. 58
Mainmenu - Service menu....................................... 59
Calling up the menu................................................. 59
Automatic software update ...................................... 60
(Software) update by satellite .................................. 61
Software Update by USB......................................... 63
Load operatingsoftware..................................................... 63
Update Channel List.......................................................... 64
Save Channel List to USB................................................. 64
Factory Reset........................................................... 64

5
List of contents
Mainmenu - Settings ................................................ 65
Calling up the menu................................................. 65
First Installation........................................................ 66
Basic Setting............................................................ 66
Video Settings.................................................................... 67
Audio Settings.................................................................... 69
Time Setting....................................................................... 70
Remote Control Code........................................................ 71
User Defined Settings.............................................. 73
Parental Lock..................................................................... 73
Customize Screen Menu................................................... 75
Programme Guide (EPG Setup)........................................ 77
Mediacenter Setup............................................................. 78
Auto. channel name update............................................... 78
Antenna & Satellite .................................................. 79
Sat Finder.......................................................................... 79
Tuner Configuration........................................................... 80
Edit Satellites..................................................................... 81
Edit Transponder............................................................... 83
Mainmenu - Interface Setup..................................... 87
Calling up the menu................................................. 87
CI+ Decryption System............................................ 88
Multidecryption................................................................... 89
Ethernet Settings ..................................................... 90
WOL (Wake on LAN) ............................................... 90
Mainmenu - Applications......................................... 91
Calling up the menu................................................. 91
Mainmenu - Language Selection............................. 92
Calling up the menu................................................. 92
Operation from the front panel
(without remote control).......................................... 93
Backup operation..................................................... 93
Software Update by USB......................................... 94
Brief technical glossary........................................... 95
Troubleshooting ....................................................... 99
Service..................................................................... 101
Subject index.......................................................... 102
Third Party Copyrights and License Terms......... 105

6
Mains power cable
Make sure that the mains cable
(power supply cable) is not damaged.
Units with a damaged mains cable
must be disconnected from the
mains (unplug it at the socket)
and repaired by an electrical
specialist before switching on again.
Only use the power supply unit
supplied (if available)!
Mortal danger due to electric shock!
Danger!
Cleaning
Disconnect the mains plug before
cleaning the unit. Use a dry cloth for
cleaning and only clean the outer
surface. Never open the casing of
the unit.
Touching the parts inside the unit
carries a risk of death due to electric
shock!
Playing children
Make sure that children do not
push any objects into the ventilation
slots.
Mortal danger due to electric shock!
Earthing
The antenna system must be
earthed or equipotentially bonded as
specified.
EN 60728/11 and any national
regulations must be complied with.
Risk of voltage surges due to lightning
strikes!
Power supply voltage
Only operate the unit at the specified
mains voltage (indicated on the
rear of the unit or on the external
power pack). The unit may only be
connected to the mains and turned
on once it has been connected to the
antenna and to the TV set or the cable
network and PC.
Moisture, direct sunlight, heat,
naked flames
Protect the unit against moisture,
dripping and splashed water (do
not place any filled objects such
as vases on top of the unit). Do not
place the unit close to a heater or
expose it to direct sunlight and do
not operate it in damp locations. Only
use the unit in a moderate climate,
not in tropical conditions! Do not
place naked flames such as candles
on top of the unit!
There is a risk of fire!
Ventilation
The heat generated in this unit is
adequately dissipated. However,
the unit should never be installed
in a cupboard or on shelves with
inadequate ventilation. Never cover
the cooling slots on the unit (e.g.
with other equipment, magazines,
tablecloths, clothing or curtains)!
Batteries
If your unit was supplied with batteries
(e.g. for the remote control), take care
that the batteries are not exposed
to excessively high temperatures,
direct sunlight or fire. Replace the
batteries only with types that are
identical or equivalent, otherwise
the batteries or the remote control
may be damaged. Also comply
with the safety instructions stated
on the batteries:
There is a risk of explosions!
Warning!
Warning!
Warning!
If the mains voltage is too high, there
is a risk of fire!
These two pages contain important information about the operation, installation location and connection
of the unit. Read these instructions carefully before setting up the device.
Safety instructions - important notes
Do not
cover!

7
Periods of extended absence,
thunderstorms, mains socket
accessibility
In order to disconnect the unit from
the mains completely, the mains plug
must be unplugged from the mains
power socket! Therefore install the
unit close to a mains socket and
make sure this socket is accessible
at all times, so that you can
disconnect the unit from the mains
if necessary.
If you are away for an extended
period, and during thunderstorms,
always switch the unit off at the mains
and unplug the power plug from the
socket. This also applies to the other
equipment connected to the unit.
Isolation from the cable network is
also recommended. Note any timer
programming (receiver) and turn
the unit on again promptly before
the recording time.
Installation location
All electronic equipment generates
heat. The temperature rise of
this unit does however lie within
the permissible range. Sensitive
furniture surfaces and veneers may
become discoloured by the effects
of constant heat over time. The feet
of the unit can also cause colour
changes to treated furniture surfaces.
If necessary, place the unit on a
suitable stable and flat base!
Repair
Ensure that any repairs to your
unit are carried out by qualified
personnel. Opening the unit and
attempting to repair it yourself will
void all warranty claims!
Improper work on the unit may
jeopardise the electrical safety of the
unit.
The manufacturer accepts no liabil-
ity for accidents caused by the user
opening the unit casing!
Connections
Incorrect wiring of the connections
may lead to malfunctions or defects
on the unit!
Caution!
Do not place any objects on top
of the unit. Unless stated to the
contrary in the “Connection and set-
up” and “Installation” sections in
the instructions supplied, maintain
a clearance of at least 10 cm
above the unit, 2 cm to either side
and 5 cm behind the unit, to allow
unobstructed dissipation of the
heat generated.
There is a risk of fire!
Electronic equipment is not domestic
waste - in accordance with directive
2002/96/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL
dated 27th January 2003 concerning
used electrical and electronic
appliances, it must be disposed of
properly.
At the end of its service life, take this
receiver for disposal at a designated
public collection point.
Used batteries are special waste!
Do not throw used batteries into
your domestic waste; take them to a
collection point for old batteries!
Safety instructions - important notes
The power supply unit and
the receiver are for indoor use
only! Use the power supply unit
supplied with the receiver. The
use of any other power supply unit
may damage the receiver.
There is a risk of fire!
Warning!

8
Product return/original packaging
Make sure that the ventilation slots on the unit are not blocked or covered in any
way. Otherwise the unit may overheat.
There is a risk of fire!
You must not disconnect the receiver from the mains while it is in operation!
This can lead to a loss of data and corruption of the software.
Safety instructions - important notes
Please keep the original packaging in case you need to return the product at any time! The receivers
are fragile due to their construction and are only adequately protected by the original packaging. If the
receiver is not shipped correctly the guarantee/warranty on it will be voided.
Before you disconnect the receiver from the mains, you must switch it to the standby mode by pressing
the standby button (on/off) on the remote control. In standby mode, any changed or new data that
are broadcast will be saved by the receiver. As soon as the receiver is in the standby mode, it can be
disconnected from the mains at any time.
Ventilation slots on the unit
Switching the receiver off
Warning!
Channel assignment
The channels available on the satellites and transponders are subject to continual change. In such cases,
it is necessary to reset the channels as the factory preset programming corresponds to the situation on
the date of manufacture. The information for these settings can be found on the Internet or in relevant
magazines.
If the receiver's remote control is not operated for four hours the receiver automatically switches
to standby mode. Before the receiver enters standby mode you get a message that you can stop
this by pressing any button on the remote control. You can deactivate this function by selecting
“Mainmenu - Settings”, “User Defined Settings”, “Customize Screen Menu”.
Automatic stand-by of the receiver after four hours

9
Updating the receiver software
Your receiver is equipped in the factory with the latest software version. We are, however, constantly
working on adapting the software to the wishes of our customers and to developments in technology.
Further information on this will be found in the sections “Mainmenu - Service Menu”.
The information in these operating instructions was correct at the time of going to print. We reserve
the right however to make changes at any time and without prior notice. If new software is released for
your receiver, and this affects the information in the operating instructions (e.g. changes to the menus
and/or functions), if we believe it necessary we will make available new operating instructions for
download at “www.kathrein.de”.
Make a note of the receiver's basic settings (these are set during first installation) so you can restore
them if necessary!
Please be aware of your responsibility towards your fellow human beings! Keep these
instructions for any questions that arise later, and if the receiver passes to another owner,
pass them on to the new owner.
Please see the UFS 946/CI+ Operating Instructions – Part 1, “Connection and set-up” for details on how
to connect the receiver and carry out first installation.
The following description of the menus and functions assumes that the UFS 946/CI+ has been correctly
connected and installed (as detailed in the operating instructions part 1 “Connection and set-up”).
Other
Safety instructions - important notes
Network function
To connect the receiver to the network via the PC/laptop, you must have unrestricted rights
(administrator rights) for your PC/laptop and on your network. For this refer to the section “Mainmenu”,
“Interface Setup”, “Ethernet Settings”.

10
Basic functions
Following an overview of the remote control, a simple explanation will be provided of the receiver’s
most important functions (with all the required buttons on the remote control). The explanations in the
sections “I would like to...” merely demonstrate the most simple use of the relevant receiver functions
without going into any great detail.
For more detailed explanations of the functions, refer to the relevant sections.

11
Basic functions
The coloured buttons are
reserved for certain content-
dependent functions
(e.g. HbbTV, teletext ...)
Volume “-” (softer)
Volume “+” (louder)
Call up teletext
Operation (on)/standby (off)
Switch between TV/radio mode
Number pad
Call up Mainmenu
Mute
Channel selection
Call up channel information (info
banner and detailed information)
Call up EPG
(Electronic Programme Guide) No function
= Navigation/channel or
options - change channel
= Call up selection box/
confirm or call up selected
menus, on-screen displays ...
Select MediaCenter (YouTube™,
Internet radio (Shoutcast™) ...)
The buttons are reserved for
certain content-dependent
functions (e.g. HbbTV)
Select last channel called up,
exit on-screen displays/
menus step by step
Remote control in live mode (TV/radio)
OTR = One Touch Recording

12
Basic functions
I want to watch TV ...
- Use
 to increase or decrease the volume
- Use
to switch channels
- Use
to display and hide again additional channel information
- Press
to mute sound
- Press
...to enter the channel number directly
- Press
to open the selection box, to select the channel list
and to call it up
- Press
to select a channel
- Press
twice to call up a
channel and close the channel
list

13
Basic functions
- Use
 to increase or decrease the volume
- Use
to switch channels
- Use
to display and hide again additional channel information
- Press
to mute sound
- Press
...to enter the channel number directly
- Press
to open the selection box, to select the channel list
and to call it up
- Press
to select a channel
- Press
twice to call up a
channel and close the channel
list
- Press
to change to radio mode
- Press
to change back to TV mode
I want to listen to the radio ...

14
Basic functions
I want to access teletext ...
- Use
...to enter the required page directly
or
- Use
 to page forward/back
- Use
to call up teletext
- Use
or to return to TV

15
Basic functions
Editing and selection options in the menus
In many menus all editing and selection options
for the respective menu will appear at the bottom
of the on-screen display. Where a specific
remote control button is required for executing
them or calling them up, this also will be shown
(see screenshot example above).
Colour Button on the remote control
Green
Yellow
Red
Blue
In some menus/displays this box is shown
with a particular colour gradation. Each
colour gradation represents a specific
view/selection. The table below shows
which colours are assigned to which
buttons. Where the functions of these
buttons are assigned for the current menu/
view, they are also shown in the line at the
bottom of the on-screen display.
Always check the bar at the bottom of
the on-screen display. This provides
information on what to do next.
Tip!

16
Basic functions
Alphanumeric entries
For entries such as names of favourites or search expressions, use the keyboard displayed on the
screen (see screenshot example).
The letters assigned to the number pad
also apply to your remote control. They are
used in a similar way to those on a mobile
phone. The following buttons can be used
for entry or to select an action:
Button Assigned character/action
press 1x2x3x4x5x
.ß?!1
abc2ä
def3
ghi4
jkl5
mno6ö
pqrs7
tuv8ü
wxyz9
1 x space, 2 x 0
Last character is deleted

17
Basic functions
Switch between letters and digits/
special characters
After entering the desired term, press the button to transfer the name/search expression, etc. or
the or button to abort the entry.
Switch to QWERTZ keyboard (control using the arrow buttons
and the OK button) - see screenshot at top right
Switch between upper case and lower case letters
Confirm the term entered
Cancel entry without saving
Cancel entry without saving

18
Basic functions
Switching between TV and Radio operation
Press the button to switch between TV and radio operation.
Adjusting the volume
Adjust the volume using the  buttons.
Channel selection
... directly
The button allows the channel to be selected from the sorted channel list/favourites list currently
selected. If the channel slot in the channel list is known, the desired channel can also be called
up directly by entering the channel slot, using the number pad on the remote control (example:
BR-alpha is at channel slot 10 in the currently selected channel list - to call it up, successively press
the  buttons on the remote control).
... from the channel list
Press the button to open the selection menu. The following on-screen display appears:
Use the buttons to select “Open the channel list” and confirm by pressing the button.
The following on-screen display appears:

19
Basic functions
Currently selected channel list Currently selected
channel
Live picture for the selected channel Signal strength and quality Channel data: - Transmitting satellite - Transponder
frequency
- Polarisation - Symbol rate - Service ID Call up the search function Switch between TV and radio channel list
Call up alphabetical sort order
Edit channel list, see section “Mainmenu - Edit TV Channellist”
Call up the complete list/satellites list
Call up the favourites lists Channel list

20
Basic functions
Now use the relevant coloured button to select the category from which you want to open a channel list:
(red) button: Call up the “Favoriteslist”
Contains the following channel lists:
- Favourites lists 1-8
(green) button: Call up the
“Complete List”
Contains the following channel lists:
- Complete list
- Channel lists ordered by satellite
(yellow) button: Call up alphabetically
sorted lists
Contains the following channel lists:
- A-Z
- Z-A
- 0-9
- Sorted by individual letters
Use the  buttons to scroll through the currently available channel lists. If you wish to see an
overview of the currently available channel lists, you must once again press the respective coloured
button for the selected category; you will then obtain the following on-screen display (for example the
favourites lists):