Kaysun KID-01 S User manual

OWNER’S MANUAL
Remote Controller
KID-01 S
Thank you very much for purchasing our air conditioner. Please read this owner’s manual
carefully before using your air conditioner.

CONTENTS
Handling the remote controller.......................................1
Remote controller Specications...................................2
Function buttons............................................................3
Indicators on LCD..........................................................5
How to use the buttons..................................................6
Auto operation...............................................................6
Cooling/Heating/Fan operation......................................6
Dehumidifying operation................................................7
Swing operation.............................................................7
Timer operation.............................................................8
ECONOMY operation..................................................11

1
Handling the remote controller
Location of the remote controller.
Use the remote controller with in a distance of 8 meters from the applian-
ce, pointing it towards the receiver. Reception is conrmed by a beep.
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials block the signals from the remote
controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose the remote controller to direct
sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not
function properly. Use curtains to prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either move these appliances or consult your
local dealer.
Replacing batteries
The remote controller is powed by two dry batteries(R03/LR03X2)
housed in the rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries,placing
the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote controller erases
all programming. After inserting new batteries, the remote controller
must be reprogrammed.

2
CAUTIONS
• Do not mix old and new batteries or batteries of a different type.
• Do not leave the batteries in the remote controller if it is not going to be used for 2 or 3 months.
• Dispose of the old batteries in the special containers to be found in the sales outlets.
Remote Controller Specications
Model KID-01 S
Rated Voltage 3.0V(Dry batteries R03/LR03 2)
Lowest Voltage of
CPU Emitting Signal 2.0V
Signal Receiving
Range
8m
~
Environment -5 C 60 C( -41OF~140OF )
Performance
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only model without), and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C(62OF~88OF).
4. Full function of LCD (Liquid Crystal Display)
NOTE:
All the illustrations in this manual are for explanation purpose only. Your air conditioner may be slightly
different.The actual shape shall prevail

3
Functions Bottons
1 TEMP DOWN Button
Push this button to decrease the indoor temper- ature setting in
1oC(2 F) increments to 30oC(88 F).
2 TEMP UP Button
Push this button to increase the indoor temper- ature set-
ting in 1oC(2 F) increments to 17oC(62 F).
3 MODE Button
Each time the button is pressed, the operation mode is selected in
the sequence of the following:
NOTE: Do not select HEAT mode if the machine you purchased is
cooling only type. Heat mode is not supported by the cooling only
appliance.
4 SWING Button(on some models)
Used to stop or start louver movement and set the desired up/down
airow direction.
5 RESET Button
Once the recessed RESET button is pressed, all of the current set-
tings will be cancelled
and the controller will return to the initial settings.
6 ON/OFF Button
Operation starts when this button is pressed and stops when the
button is pressed again.
7 FAN SPEED Button
Used to select the fan speed in four steps:
Some models have no MED FAN feature.
8 TIMER ON Button
Press this button to activate the Auto-on time setting. Each press will
increase the time setting
9 ECONOMY(SLEEP) Button
Select this function during the sleeping time. It can maintain the
most comfortable temperature and save energy. This function is
available on COOL, HEAT or AUTO mode only .

4
Functions Bottons
(continued)
Note:
KID-01 S model have on FOLLOW
ME button.
NOTE: While the unit is running under SLEEP mode, it would be can-
celled if ON/OFF, FAN SPEED, SLEEP or MODE button is pressed.
10 TIMER OFF Button
Press this button to activate the Auto-off time setting. Each press will
increase the time setting in 30 minutes increments, up to 10 hours,
then at 1 hour increments up to 24 hours. To cancel the Auto-off time
setting, just press the button until the time setting is 0.0.
11 LOCK Button
Press this recessed button to lock all current
settings, and the remote controller will not accept any operation
except that of the LOCK. Use the LOCK mode when you want to
prevent settings from being changed accidentally. Press the LOCK
button again to cancel the LOCK function. A lock symbol will appear
on the remote controller display when the lock function is activated.
12 LED Display Button
Press this button to clear the display on the
indoor unit, press it again to light the display .
13 FOLLOW ME/TEMP SENSING Button
Press this button to initiate FOLLOW ME function. When the Follow
Me function is activated, the remote display is actual temperature at
its location. The remote control will send this signal to the air conditio-
ner every 3 minutes interval until press
the Follow Me button again.
The Follow Me function is not available under DRY and FAN mode.
Switch the operation mode or turn off the unit will cancel the follow
me function automatically.
14 ION Button
When push this button, the ion generator is energized and will help to
remove pollen and impurities from the air.

5
Indicators on LCD
MODE display
Displays the current selected mode. Including AUTO, COOL, DRY,
HEAT (cooling & heating models only) and FAN.
Transmission Indicator
This transmission indicator will light when remote
controller transmits signals to the indoor unit.
Temp./Timer display
The temperature setting (from 17OC(62O F) to
30OC(88OF)) or timer setting (0~24h) will be displayed.
If FAN mode is selected, there will be no display.
ON/OFF display
This indicator will be displayed when the unit is operating.
MODE display(FAN mode)
FAN SPEED display
Displays the selected fan speed: AUTO, HIGH, MED and LOW. No-
thing displays when the fan speed is selected in AUTO speed. When
AUTO or DRY Mode is selected, there will be no signals displayed.
FOLLOW ME display
When pressing FOLLOW ME/TEMP SENSING button in COOL or
HEAT mode, the remote sensing function is activated and this indica-
tor displays.
TIMER display
This display area shows the settings of the TIMER. That is, if only
the Auto-on time function is set, it will display TIMER ON. If only the
Auto-off time function is set, it will display TIMER OFF. If both func-
tions are set, it will display TIMER ON OFF which indicates you have
chosen both the Auto-on time and Auto-off time.
LOCK Indicator
LOCK display is displayed when pushing the LOCK
button. Push the LOCK button to clear display.

6
How to use the buttons
Auto operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the display panel of the
indoor unit illuminates.
1. Press the MODE button to select Auto.
2. Press the TEMP button to set the desired temperature. The tempe-
rature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F) increments.
3. Press the ON/OFF button to start the air conditioner.
NOTE
1. In the Auto mode, the air conditioner can logically choose the mode
of Cooling, Fan, Heating and Dehumidifying by sensing the difference
between the actual ambient room temperature and the set temper-
ature on the remote controller.
2. In the Auto mode, you can not switch the fan speed. It has already
been automatically controlled.
3. If the Auto mode is not comfortable for you , the desired mode can
be selected manually.
Cooling /Heating/Fan operation
Ensure the unit is plugged in and power is available.
1. Press the MODE button to select COOL, HEAT, (cooling & heating
models only) or FAN mode.
2. Press the TEMP button to set the desired temperature. The tempe-
rature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F) increments.
3. Press the FAN SPEED button to select the
fan speed in four steps- Auto, Low, Med,or High.
4. Press the ON/OFF button to start the air conditioner.
NOTE
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not able to control the
room temperature either. In this case, only step 1, 3 and 4 may be
performed.

7
How to use the buttons
Dehumidifying operation
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the display panel of the
indoor unit illuminates.
1. Press the MODE button to select DRY mode.
2. Press the TEMP button to set the desired temperature. The tempe-
rature can be set
within a range of 17 C(62 F)~ 30 C in 1 C(2 F) increments.
3. Press the ON/OFF button to start the air conditioner.
NOTE
In the Dehumidifying mode, you can not switch the fan speed. It has
already been automatically controlled.
Swing operation(on some models)
Use the SWING button to adjust the Up/Down airow direction .
1. When press the button once and quickly, the air ow direction set-
ting feature of the louver is activated. The moving angle of the louver
is 6o for each press. Keep pressing the button to move the louver to
the desired position.
NOTE:On some models press it to initiate the Auto swing feature
only.
2. If keep pressing the SWING button without releasing for 2 more se-
conds, the auto swing feature of the louver is activated. The horizon-
tal louver would swing up/down automatically. Press it again to stop.
NOTE: When the louver swing or move to a position which would
affect the cooling and heating effect of the air conditioner, it would
automatically change the swing/ moving direction.

8
How to use the buttons
Timer operation
press the TIMER ON button can set the auto-on time of the unit. And
press the TIMER OFF button can set the auto-off time of the unit.
To set the Auto-on time.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on setting time and the sig-
nal “h” will be shown on the LCD display area. Now it is ready to reset
the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired Auto-on time.
Each time you press the button, the time increases in 30 minutes
increments, up to 10 hours, then at 1 hour increments up to 24 hours.
3. After setting the TIMER ON ,there will be a one- half second delay
before the remote controller transmits the signal to the air conditio-
ner. Then, after approximately another 2 seconds, the signal “h” will
disappear and the set temperature will re-appear on the LCD display
window.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote controller shows TIMER
OFF, the last Auto-off setting time and the signal “h” will be shown on
the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired Auto-off time.
Each time you press the button, the time increases in 30 minutes
increments, up to 10 hours, then at 1 hour increments up to 24 hours.
3. After setting the TIMER OFF ,there will be a one- half second delay
before the remote controller transmits the signal to the air conditio-
ner. Then, after approximately another 2 seconds, the signal “h” will
disappear and the set temperature will re-appear on the LCD display
window.

9
IMPORTANT
The effective operation time set by the remote controller for the timer function is limited to the following
settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
Example of Timer setting
TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want the unit to turn on automa-
tically before say when you return home. The air conditioner will automa- ti-
cally start operating at the set time.
Example:
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of starting operation
time and the signal “h” will show on the display area.
2. Press the TIMER ON button to display “6:0h” on the TIMER ON
display of the remote controller.
3. Wait for about 3 seconds and the digital display area will show the
temperature again. Now this function is activated.

10
TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when you want the unit to turn off
automatically after you go to bed. The air conditioner will stop auto-
matically at the set time.
Example:
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of stopping operation
time and the signal “h” will show on the display area.
2. Press the TIMER OFF button to display “10h” on the TIMER OFF
display of the remote controller.
3. Wait for about 3 seconds and the digital display area will show the
temperature again. Now this function is activated.
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF → TIMER ON
(On → Stop → Start operation)
This feature is useful when you want to stop the air conditioner after
you go to bed, and start it again in the morning when you wake up or
when you return home.
Example:
To stop the air conditioner 2 hours after setting and start it again 10
hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0h on the TIMER
OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10h on the TIMER
ON display .
5. Wait for the remote control to display the setting temperature

11
TIMER ON → TIMER OFF
(Off → Start → Stop operation)
This feature is useful when you want to start the air conditioner before
you wake up and stop it after you leave the house.
Example:
To start the air conditioner 2 hours after setting, and stop it 5 hours
after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to display 2.0h on the TIMER
ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display 5.0h on the TIMER
OFF display .
5. Wait for the remote control to display the setting temperature
CAUTION
Setting the timer (TIMER ON or TIMER OFF) in sequence occurs
directly after rst activating the setting time.
ECONOMY(SLEEP) operation
Active/Disable sleep function. It can maintain the most comfortable
temperature and save energy. This function is available on COOL,
HEAT or AUTO ,m, ode only., For the de,t,ail, see Sleep operation in
USER S MANUAL.
NOTE: While the unit is running under SLEEP mode, it would be can-
celled if MODE, FAN SPEED or ON/OFF button is pressed.

12
NOTE:
-Buttons design is based on typical model and might be slightly different from the actual one you purchased,
the actual shape shall prevail.
-All the functions described are accomplished by the unit, if the unit has no this feature, there is no corres-
ponding operation happened when
press the relative button on the remote controller.
-When there are wide differences between Remote controller Illustration and USERS MANUAL on function
description, the description on USERS MANUAL shall prevail.
-The device could comply with the local national regulations. In Canada, it should comply with CAN ICES-
3(B)/NMB-3(B). In USA, this device
complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interfe- rence, and (2) this device must ac-
cept any interference received,
including interference that may cause undesired operation.
-This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct
the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Changes or modications not approved by
the party responsible for compliance could void suers authority to operate the equipment.

13
The design and specications are subject to change without prior notice for product improvement. Consult
with the sales agency or manufacturer for details.
CR054-RG51B13 202055091305
20141117