Kaysun KID-03 User manual

OWNER’S MANUAL
Air Conditioner Remote Controller
KID-03
Thank you very much for purchasing our air conditioner.
Please read this owner's manual carefully before using your air conditioner.
Make sure to save this manual for future reference.

CONTENTS
1. Remote controller Specifications. ................................................................................ 1
2. Operation buttons ........................................................................................................ 2
3. Indicators on LCD ........................................................................................................ 4
4. How to use the buttons ................................................................................................ 5
4.1. Auto operation. ........................................................................................................... 5
4.2. Cooling/Heating/Fan operation. ................................................................................. 5
4.3. Dehumidifying operation ............................................................................................. 6
4.4. Timer operation. ......................................................................................................... 6
5. Handling the remote controller .................................................................................... 10
NOTE:
Buttons design is based on typical model and might be slightly different from the actual
one you purchased the actual shape shall prevail.
All the functions described are accomplished by the unit. If the unit has no this feature,
there is no corresponding operation happened when press the relative
button on the remote controller
When there are wide differences between. Remote controller Illustration and, USER'S
MANUAL on function description, the description of USER'S MANUAL shall prevail.

1
1. Remote controller specifications
Model
KID-03
Rated Voltage
3.0V (Dry batteriesR03/LR03×2)
Signal Receiving Range
8m
Environment
-5ºC ~60ºC
KID-03

2
2. Operation buttons
1- ON/OFF Button
This button turns the air conditioner ON and OFF.
2- MODE Button
Press this button to modify the air conditioner mode in a sequence of following:
NOTE: Please do not select HEAT mode if the machine you purchased is cooling only type.
Heat mode is not supported by the cooling only appliance.
3- FAN Button
Used to select the fan speed in four steps:
NOTE: You can not switch the fan speed in AUTO or DRY mode..
4- SLEEP Button
• Active/Disable sleep function. It can maintain the most comfortable
temperature and save energy. This function is available on COOL, HEAT
or AUTO mode only.
• For the detail, see sleep operation in “USERS MANUAL”.
NOTE: While the unit is running under SLEEP mode, it would be cancelled if
MODE, FAN SPEED or ON/OFF button is pressed.
6- TURBO Button
Active/Disable Turbo function. Turbo function enables the unit to reach the
preset temperature at cooling or heating operation in the shortest time (if
the indoor unit does not support this function, there is no corresponding
operation happened when pressing this button).
8- UP Button
Push this button to increase the indoor temperature setting in 1oC
increments to 30oC.
DOWN Button
Push this button to decrease the indoor temperature setting in 1oC
increments to 17oC.
NOTE: Temperature control is not available in Fan Mode.
9- SHORTCUT Button

3
• Used to restore the current settings or resume previous settings.
• On the first time connecting to the power, if push the SHORTCUT button,
the unit will operate on AUTO mode, 26ºC, and fan speed is Auto.
• Push this button when remote controller is on, the system will automatically
revert back to the previous settings including operating mode, setting
temperature, fan speed level and sleep feature (if activated).
• If pushing more than 2 seconds, the system will automatically restore the
current operation settings including operation mode, setting temperature,
fan speed level and sleep feature (if activated).
10- TIMER ON Button
Press this button to initiate the auto-on time sequence. Each press will
increase the auto-timed setting in 30 minutes increments. When the setting
time displays 10.0, each press will increase the auto-timed setting 60
minutes increments. To cancel the auto-timed program, simply adjust the
auto-on time to 0.0.
11- TIMER OFF Button
Press this button to initiate the auto-off time sequence. Each press will
increase the auto-timed setting in 30 minutes increments. When the setting
time displays 10.0, each press will increase the auto-timed setting 60
minutes increments. To cancel the auto- timed program, simply adjust the
auto-off time to 0.0
12- Swing Button
Used to stop or start horizontal louver auto swing feature.
DIRECT Button
Used to change the louver movement and set the desired up/down air flow
direction.
The louver changes 6º in angle for each press.
14- LED Button
Disable/Active indoor screen Display. When pushing the button, the indoor
screen display is cleared, press it again to light the display.

4
3. Indicators on LCD
Information are displayed when the remote controller
is powered up.
Mode display
Displayed when data transmitted.
Displayed when remote controller is ON.
Battery display (low battery detection).
Not available for this unit
Displayed when TIMER ON time is set.
Displayed when TIMER OFF time is set.
Show set temperature or room temperature, or time under
TIMER setting.
Displayed in Sleep Mode operation.
Indicated that the air conditioner is operating in Follow me
mode.
Not available for this unit.
Not available for this unit.
Fan speed indication
Low speed
Medium speed
High speed
Auto fan speed
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the
actual operation only the relative functional signs are shown on the display window.

5
4. How to use the buttons
4.1. Auto operation
Ensure the unit is plugged in and power
is available. The OPERATION indicator
on the display panel of the indoor unit
starts flashing.
1. Press the MODE button to select
Auto.
2. Press the UP/DOWN button to set
the desired temperature. The
temperature can be set within a
range of 17ºC~ 30ºC in 1ºC
increments.
3. Press the ON/OFF button to start the
air conditioner.
NOTE
1. In the Auto mode, the air conditioner can
logically choose the mode of Cooling,
Fan, and Heating by sensing the
difference between the actual ambient
room temperature and the setting
temperature on the remote controller.
2. In the Auto mode, you can not switch the
fan speed. It has already been
automatically controlled.
3. If the Auto mode is not comfortable for you, the desired mode can be selected manually.
4.2. Cooling /Heating/Fan operation
Ensure the unit is plugged in and power is available.
1. Press the MODE button to select COOL, HEAT (cooling & heating models
only) or FAN mode.
2. Press the UP/DOWN buttons to set the desired temperature. The
temperature can be set within a range of 17ºC~ 30ºC in 1ºC increments.
3. Press the FAN button to select the fan speed in four steps- Auto, Low, Med,
or High.
4. Press the ON/OFF button to start the air conditioner
NOTE
In the FAN mode, the setting temperature is not displayed in the remote controller and you are
not able to control the room temperature either. In this case, only step 1, 3 and 4 may be
performed.

6
4.3. Dehumidifying operation
Ensure the unit is plugged in and power
is available. The OPERATION indicator
on the display panel of the indoor unit
starts flashing.
1. Press the MODE button to select
DRY mode.
2. Press the UP/DOWN buttons to set
the desired temperature. The
temperature can be set within a
range of 17ºC~ 30ºC in 1ºC
increments.
3. Press the ON/OFF button to start
the air conditioner.
NOTE
In the Dehumidifying mode, you can not switch
the fan speed. It has already been
automatically controlled.
4.4. Timer operation
Press the TIMER ON button can set the
auto-on time of the unit. Press the TIMER OFF button can set the auto-off time
of the unit
To set the Auto-on time.
1. Press the TIMER ON button. The remote controller shows TIMER ON, the last
Auto-on setting time and the signal "H" will be shown on the LCD display area.
Now it is ready to reset the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired Auto-on time. Each time you
press the button, the time increases by half an hour between 0 and 10 hours
and by one hour between 10 and 24 hours.
3. After setting the TIMER ON, there will be a one second delay before the remote
controller transmits the signal to the air conditioner. Then, after approximately
another 2 seconds, the signal "h" will disappear, and the set temperature will
re-appear on the LCD display window.

7
To set the Auto-off time.
1. Press the TIMER OFF button. The remote controller shows TIMER OFF, the last
Auto-off setting time and the signal "H" will be shown on the LCD display area.
Now it is ready to reset the Auto-off time to stop the operation.
2. Push the TIMER OFF button again to set desired Auto-off time. Each time you
press the button, the time increases by half an hour between 0 and 10 hours and
by one hour between 10 and 24 hours.
3. After setting the TIMER OFF, there will be a one second delay before the remote
controller transmits the signal to the air conditioner. Then, after approximately
another 2 seconds, the signal "H " will disappear and the set temperature will re-
appear on the LCD display window.
CAUTION
• When you select the timer operation, the remote controller automatically
transmits the timer signal to the indoor unit for the specified time. Therefore,
keep the remote controller in a location where it can transmit the signal to the
indoor unit properly.
• The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5,
4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14,
15,16,17, 18, 19, 20, 21, 22, 23 and 24.
Example of timer setting
TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.
Example:
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of starting
operation time and the signal "H" will show on the display
area.
2. Press the TIMER ON button to display "6.0H " on the
TIMER ON display of the remote controller.
3. Wait for 3 seconds and the digital display area will show
the temperature again. The "TIMER ON" indicator remains
on and this function is activated.

8
TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when you want
the unit to turn off automatically after you go to bed.
The air conditioner will stop automatically at the set
time.
Example:
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of stopping
operation time and the signal "H" will show on the display
area.
2. Press the TIMER OFF button to display "10H " on the
TIMER OFF display of the remote controller.
3. Wait for 3 seconds and the digital display area will show
the temperature again. The "TIMER OFF" indicator remains on and this function is
activated.
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF → TIMER ON
(On →Stop→ start operation)
This feature is useful when you want to stop
the air conditioner after you go to bed and
start it again in the morning when you wake
up or when you return home.
Example:
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0h
on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10h on the TIMER ON display.
5. Wait for 3 seconds and the digital display area will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function is activated.

9
TIMER ON → TIMER OFF
(Off→ Start→ Stop operation)
This feature is useful when you want to start the air conditioner before you
wake up and stop it after you leave the house.
Example:
To start the air conditioner 2 hours after setting and stop it 5
hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to display 2.0h on the
TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display 5.0h on
the TIMER OFF display.
5. Wait for 3 seconds and the digital display area will show
the temperature again. The "TIMER ONOFF" indicator
remains on and this function is activated.

10
5. Handling the remote controller
Location of the remote controller.
Use the remote controller within 8 meters from the
appliance, pointing it towards the receiver.
Reception is confirmed by a beep.
CAUTIONS
• The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
• Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
• If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
• Do not drop the remote controller. Handle with care.
• Do not place heavy objects on the remote controller, or step on it.
Using the remote controller holder (optional)
• The remote controller can be attached to a wall or pillar by using
a remote controller holder (not supplied, purchased
separately).
• Before installing the remote controller, check that the air
conditioner receives the signals properly.
• Install the remote controller with two screws.
• For installing or removing the remote controller, move it up or
down in the holder

11
Replacing batteries
The following cases signify exhausted batteries. Replace old batteries with
new ones.
• Receiving beep is not emitted when a signal is transmitted.
• Indicator fades away.
Your air conditioning unit may come with two batteries
(some units). Put the batteries in the remote control
before use:
(1) Remove the cover in the rear part of the
remote controller.
(2) Remove the old batteries and insert the new
batteries, placing the (+) and (-) ends correctly.
(3) Install the cover back on.
NOTE
When the batteries are removed, the remote controller erases all programming. After inserting
new batteries, the remote controller must be reprogrammed.
CAUTIONS
• Do not mix old and new batteries or batteries of different types.
• Do not leave the batteries in the remote controller if they are not going to
be used for 2 or 3 months.
• Do not dispose batteries as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.

CR132-RG57A3
16117000A00610
20200407

The design and specifications are subject to change without prior
notice for product improvement. Consult with the sales agency or
manufacturer for details.