KBL beautyShaper User manual

OPERATING INSTRUCTIONS
BEAUTY SYSTEM
beautyShaper
Tower

ORIGINAL OPERATING INSTRUCTIONS
Version: BA-beautyShaper-Tower-TSU-en-us
Date: October 2020
Item no: 0100035998 A
Device name [tech.]: T3/50 - 180 c
Copyright and Trademark
© Copyright 2020 KBL GmbH
This documentation only covers products manufactured by KBL GmbH. It must not be duplicated, photocopied,
translated or stored without prior special consent by KBL GmbH. Duplication on electronic media or in a machine
readable form, either in whole or in part, is also prohibited.
is a registered trademark of KBL GmbH.
DISCLAIMER
All information given in this document correspond to the status quo at the date of publication but may be subject
to changes. Therefore, we do not accept any liability for, nor do we guarantee the accuracy and/or completeness
of the information.
EXPORT
Technical equipment and versions of the devices are in accordance with the legal prescriptions of the respective
country of destination. Export to the European Union of the KBL products, listed in this guide, or operation of
the systems in these countries, are not permitted. KBL does not accept any manufacturers liability in case this
direction is not adhered to. It is expressly pointed out that any violation of the export/operation prohibition will
involve substantial risks of liability for the exporter and/or operator.
MANUFACTURER
KBL GmbH
Ringstraße 24-26 · 56307 Dernbach · Germany
DISTRIBUTED BY (CONTACT)
Laundries unlimited of Indiana, Inc.
dba Tanning Supplies unlimited.
1504 Sadlier Circle South Drive;
Indianapolis; IN 46239, U.S.A.
1-877-307-8434 (toll free) or 317-217-1700

Contents
1. Labels attached to the device .......................... 5
2. General information .......................................... 6
2.1 About these instructions ............................... 6
2.2 Safety signs................................................... 6
2.3 Signal words.................................................. 7
2.4 Denitions...................................................... 7
2.5 Transport ....................................................... 7
2.6 Environmental regulations............................. 8
2.7 Service........................................................... 8
2.8 Updating system software ............................ 8
2.9 Setup location ............................................... 8
2.10 Commissioning............................................ 9
2.11 Obligations of the studio operator ........... 10
2.12 Training of staff.......................................... 10
2.13 Technical modications............................. 10
2.14 Instruction updates ................................... 10
3. Safety notes ..................................................... 11
3.1 General safety notes ................................... 11
3.2 Duties of the operator ................................. 11
3.3 Intended use................................................ 12
3.4 Indications for use....................................... 12
3.5 Contraindications ........................................ 12
3.6 Warnings ..................................................... 12
3.7 Foreseeable misuse .................................... 12
3.8 Misuse ......................................................... 12
3.9 Timer controlled operation .......................... 13
3.10 Guidelines for the use of prot. eyewear .... 13
3.11 Freeing a trapped person.......................... 13
3.12 Use of headphones ................................... 13
3.13 Lamp breakage ......................................... 13
4. Description of the device................................ 14
4.1 Standards.................................................... 14
4.2 Components................................................ 17
5. Connections..................................................... 18
5.1 Class I ME equipment ................................. 18
5.2 Overview supply connections ..................... 18
5.3 Connecting the mains voltage..................... 18
5.4 Connecting an external audio source ......... 19
5.5 Level adjustment studio music.................... 19
5.6 Operation using different audio sources ..... 20
5.7 Bluetooth connection .................................. 20
5.8 Connecting the channel selection............... 21
5.9 Connecting the external timer..................... 22
6. Start-up ............................................................ 23
6.1 Operating modes......................................... 23
7. Usage................................................................ 24
7.1 Instructions for the user .............................. 24
8. Operating mode............................................... 25
8.1 Starting a session........................................ 25
8.2 Operation during the session ...................... 25
8.3 Functions overview ..................................... 27
9. Standby mode..........................................................28
9.1 Service mode .............................................. 28
9.2 Standby functions ....................................... 28
10. Maintenance and cleaning ........................... 29
10.1 Instructions on cleaning, disinfection
and care .................................................... 30
10.2 Maintenance intervals ............................... 33
10.3 Tools and aids ........................................... 34
10.4 Acrylic panes............................................. 34
10.5 Tubes......................................................... 35
10.6 Interior unit lighting.................................... 36
10.7 Recording to an SD card........................... 37
11. System messages ......................................... 38
12. Technical Data ............................................... 40
12.1 Dimensions and distances ........................ 41
13. Implied warranty............................................ 42
14. WARRANTY CARD ........................................ 43
Operating Instructions |KBL Tower beautyShaper
4

(3230074786)
50 x beautyLight 1.9/18
(T3/50-180-c)
KBL beautyShaper
Rated capacity:
3 x 220 V / ~ / 60Hz
Fluorescent-Tubes :
11012340
Mains-Voltage:
Serial number:
10150 W
Manufactured:
Typ:
CAUTION! WARNING!
No.: 0100005000
ATTENTION! AVERTISSEMENT!
CONNECT ONLY TO A CIRCUIT PROTECTED
BY A CLASS A GROUND
FAULT CIRCUIT INTERRUPTER.
BRANCHER SEULEMENT À UNE
DÉRIVATION PROTÉGÉE PAR
UN DISJONCTEUR DIFFÉRENTIEL
DE CLASSE A.
POUR UN FONCTIONNEMENT SÙR,
NE JAMAIS UTILISER CET APPAREIL
QUAND LE CONDUCTEUR DE MISE À
LA MASSE EST DÉCONNECTÉ.
GROUNDING CIRCUIT CONTINUITY IS
VITAL FOR SAFE OPERATION OF EQUIPMENT.
NEVER OPERATE EQUIPMENT WITH GROUNDING
CONDUCTOR DISCONNECTED.
Use in dry locations only IP20
09/2020
(01)04260489020180(11)200903(21)11012340
2 x 220 V / ~ / 60Hz
KBL GmbH
Ringstrasse 24-26
56307 Dernbach
Germany
Manufactured by:
Laundries unlimited of Indiana, Inc.
dba Tanning Supplies unlimited
1504 Sadlier Circle South Drive
Indianapolis, IN 46239, U.S.A.
Distributed by:
EXAMPLES
1. Labels attached to the device
Operating Instructions |KBL Tower beautyShaper 5

2.1 About these instructions
This operating manual is intended for use by
• studio operator,
• user,
• staff,
• qualied, trained and authorized service technician.
Any person dealing with this KBL Product (hereafter
referred to as device) must have read and understood
these instructions. This manual describes devices
equipped with the maximum number of features.
Keep this manual ready to hand at all times.
Statements about expected performance etc.
have not been evaluated by the FDA (Food & Drug
Administration). This product is not intended to treat,
cure or prevent any disease. The information con-
tained in this manual is not a substitute for advice
from a licensed physician or other healthcare profes-
sional. Actual results may vary depending on use,
genetic inuences, diet, exercise, lifestyle, etc. The
manufacturer gives no guarantee of results.
FURTHER INSTRUCTIONS – BEAUTYSHAPER SYSTEM
The „beautyShaper“ system consists of a light emit-
ting Tower device and the training platform „vibraN-
ano“. The operating instructions of the vibraNano,
article number: 0100036269, is enclosed separately
with each beautyShaper delivery as part of the ove-
rall system.
2.2 Safety signs
This symbol indicates that general haz-
ards exist for the human health.
This symbol indicates that due to elec-
trical tensions hazards exist to the
human health.
This symbol indicates that due to UV
radiation hazards exist to the human
health.
This symbol indicates that due to fall-
ing loads hazards exist to the human
health.
This symbol indicates the danger of
pinching.
When closing and opening panels and
covers, you can pinch your hands.
This symbol indicates the danger of
burns from hot lamps and housing parts.
If the device was operated before
being switched off and opened,
lamps and housing parts may be hot.
This symbol indicates that damages
may occur at the device, at the material
or at the environment.
This symbol indicates the type BF
applied part.
IMPORTANT INFORMATION
This symbol does not identify safety
notices, but states information for a bet-
ter understanding.
2. General information
Operating Instructions |KBL Tower beautyShaper
6

2.3 Signal words
DANGER
• Death or serious injury is imminent.
WARNING
• Death or serious injury is possible.
CAUTION
• Moderate or minor injury is possible.
2.4 Denitions
STUDIO OPERATOR
People who provide devices to users on a commer-
cial basis. The studio operator is trained to oper-
ate and maintain the device. She/he is responsible
for the proper operation of the device as well as for
compliance with the maintenance intervals.
USER
A person who uses the device.
STAFF
People who are responsible for the operation, clean-
ing and disinfection as well as for the general main-
tenance work and instruction of the user on how to
operate the devices.
QUALIFIED, TRAINED AND AUTHORIZED SER-
VICE TECHNICIAN
Qualied staff who have been trained and authorized
by the manufacturer for assembly and maintenance
work with specic device.
2.5 Transport
WARNING
Overturning load
Danger of being crushed by heavy parts
of the equipment.
• Keep the safety distance to the trans-
port machine.
• Do not walk under the load.
• Wear safety shoes.
TRANSPORT BY FORKLIFT TRUCK
During transport the device may be dam-
aged when using forklift forks that are too
short.
• Use only sufciently long forks.
The box with the device components is mounted on
a pallet.
• Insert the forks carefully into the openings of the
pallet.
• Lift the load by a few centimeters.
• Transport the load carefully to the place of instal-
lation.
OTHER MODES OF TRANSPORT
If a forklift truck cannot be used for transport, the
box must be unpacked and the parts inside must
be transported individually to the place of installa-
tion, e.g. using a dolly. Depending on the weight of
the components, lifting them might require several
people.
Operating Instructions |KBL Tower beautyShaper 7

Operating Instructions |KBL Tower beautyShaper
8
2.6 Environmental regulations
(disposal of lamps)
Fluorescent lamps contain uorescent materials and
other waste products containing mercury. Some
areas of the USA and Canada have specic regu-
lations regarding disposal of these waste. Please
check the laws in your area and act in accordance
with municipal waste regulations. Please retain proof
of proper disposal of lamps. Your local regulatory
agency can assist you with the disposal of lamps.
Report the number of lamps to your local agency by
telephone or in writing. The regulatory agency can
provide you with a delivery point for your lamps or will
take care, in conjunction with a disposal company,
of the collection and proper disposal of the lamps
(Fees for this may apply). Please contact your code
enforcement ofcials for more information regard-
ing laws governing disposal of these components in
your area.
2.7 Service
REPAIRS - SERVICE - REPLACEMENT - PARTS
AND LAMPS - EYE PROTECTION - OPERATING
AND ASSEMBLY INSTRUCTIONS
If you are in need of any of the above mentioned
products or services, you should contact:
Laundries unlimited of Indiana, Inc.
dba Tanning Supplies unlimited.
1504 Sadlier Circle South Drive;
Indianapolis; IN 46239, U.S.A.
1-877-307-8434 (toll free) or 317-217-1700
ACCESSORY PARTS
Description KBL item no.
Protective eyewear 3010104000
2.8 Updating system software
Risk of damage by switching off the
power supply voltage.
Disconnecting power supply during the
update process, will lead to damage of
electronic components.
• Make sure that the device is not dis-
connected from the power supply
voltage during the update.
To accomplish the update download the “USB-
Connect” software offered by KBL. For detailed
information press the help-button in the main menu.
2.9 Setup location
OPERATION IN MOBILE FACILITIES
CAUTION
Crushing hazard caused by sudden
movements
The device is unsuitable for operation in
mobile facilities (buses, trains, ships).
• The device must be adapted in order
to ensure trouble-free operation when
used in mobile facilities.
DANGER OF OVERHEATING BY OBSTRUCTION
OF THE AIRFLOW
Avoid in any case a change, obstruction or block-
age of the air inow and outow area to the device
or to make any unauthorized changes to the device.
The manufacturer shall bear no liability for damage or
injuries resulting from such actions.
• Comply with the ventilation information to avoid
serious system malfunctions.
• Only use OEM spare parts of the same type! The
use of other parts will void the manufacturer’s war-
ranty!
• Maintain the minimum distances from ceiling, bot-
tom and the walls! Dimensions are given in chapter
technical data.
Insufcient air supply leads to overheat-
ing which may result in damaging the
device!

Operating Instructions |KBL Tower beautyShaper 9
EXPLOSIVE ATMOSPHERE
DANGER
Explosive atmosphere
Operation in explosive atmospheres can
cause explosions.
• Do not operate the device in an explo-
sive atmosphere.
SALTY AIR - CONTAMINATED AIR
Salty air, contaminated air may lead to
corrosion of the housing and electrical
components. Damage to the device
possible!
• Do not operate the device in locations
with aggressive environmental conditions
(e.g. air containing chlorine).
• Do not install the device at swimming
pools.
ELECTROMAGNETIC ENVIRONMENT
Do not use near (24 inches or closer) equipment sen-
sitive to electromagnetic interference.
This device complies with International Standards
(as set forth in manufacturer’s declaration following)
for electromagnetic compatibility for medical electri-
cal equipment and/or systems.
These standards are designed to provide reasonable
protection against harmful interference in a typical
medical installation.
However, because of the proliferation of radio-fre-
quency transmitting equipment and other sources of
electrical noise in healthcare and other environments,
it is possible that high levels of such interference due
to close proximity or strength of a source might dis-
rupt the performance of this device. Medical electri-
cal equipment needs special precautions regarding
EMC, and all equipment must be installed and put
into service according to the EMC information speci-
ed in this manual
(chapter 4.1) .
DIFFERENCE IN TEMPERATURE
Risk of damage by switching on the
power supply voltage.
When there are great differences in tempera-
ture between the transportation route and the
installation site the device shall not be put into
operation immediately after being set up.
• Before connecting the device to the
power supply, wait at least for 2 hours.
2.10 Commissioning
DANGER
Damaged mains power cable
Risk of death or fatal injury due to electric
shock when touching a damaged mains
power cable.
• Only the manufacturer or specialized
companies may replace the mains
power cable!
Initial commissioning will be carried out by the man-
ufacturer’s own service technicians or by qualified,
trained and authorized service technicians. The
device will be handed over ready for use.
As studio operator it is your responsibility to observe
the electrical regulations applicable at the installation
site.
The device incorporates special preventive measures
with regard to the electromagnetic compatibility and
must be installed and commissioned according to
the EMC instructions obtained from this operating
instructions.
If the device has not been used for a longer period
of time, then it must rst be inspected by qualied,
trained and authorized service technicians, before
being put back into operation again.
Ensure no electromagnetic compatibility issues with
the siting
(chapter 4.1) .

Operating Instructions |KBL Tower beautyShaper
10
2.11 Obligations of the studio
operator
• The studio operator is responsible for informing
users on possible risks of using the device.
• All danger and safety labels attached to the device
must be observed and shall not be removed!
• The device shall only be used when in proper oper-
ational condition!
• The studio operator is responsible to ensure that
the device is handled properly.
• No safety equipment (e.g. thermal switch) shall be
removed, deactivated, or otherwise bypassed as it
may impair the safe operation of the device!
• The electrical installation must be equipped
with a freely accessible all-pole disconnecting
device (Master switch with clearly marked on/off
settings e.g. “O” and “I” or additional indica-
tor light). The master switch shall be tted exter-
nally on the side of the booth, so the operator can
access it at any time, even when the device is in
operation.
• Site the device in such a way as the MAINS ON/
OFF switch and the MAINS supply cable are not
obstructed (difcult to access).
• Before rst use, all users must be introduced to the
device by means of a guided live session.
2.12 Training of staff
The studio operator is obligated to train her/his staff
and to instruct them in the established legal and
accident prevention regulations. She/he must ensure
that her/his staff has understood and observes these
instructions. This includes:
• Operating instructions.
• Safety instructions.
• Information regarding intended use and foresee-
able misuse.
• Cleaning/disinfection and maintenance instruc-
tions.
- The instructions and additional information from
the manufacturer must be available to the staff at
their workplace. Regularly test your staff‘s safety
consciousness and awareness of the risks, tak-
ing into account the operating instructions of the
device.
- Make sure that the cleaning/disinfection intervals
are complied with, especially the cleaning and dis-
infection of the device after every use.
- Make sure that your staff provides the customers
with appropriate advice, especially regarding oper-
ating times, possible risks and the operation of the
device.
2.13 Technical modications
The device has been constructed in accordance with
current safety regulations.
The specications and illustrations on these instruc-
tions are subject to technical modications which are
required in order to improve the device.
• Unauthorized modications and changes to the
device are forbidden.
• Use only OEM spare parts!
2.14 Instruction updates
Use the current device
documentation
The device documentation is updated
regularly by the manufacturer. Make sure
you are using the latest version.
For instruction updates, please contact:
Laundries unlimited of Indiana, Inc.
dba Tanning Supplies unlimited.
1504 Sadlier Circle South Drive;
Indianapolis; IN 46239, U.S.A.
1-877-307-8434 (toll free) or 317-217-1700

3.1 General safety notes
WARNING
Risk of injury from UV radiation
The use of UV lamps with this device can
cause serious injury to the skin and eyes.
• Never operate the device with UV
lamps.
The use of UV lamps or lamps other than those speci-
ed for this device can lead to serious injuries and is
prohibited.
Offenses are considered a violation of the FDA regu-
lation 21 CFR 1040.20 and can lead to nes and / or
imprisonment.
Any unauthorised change (e.g. relabelling or use of
UV lamps) lead to noncompliance of the device with
applicable regulations and specications designed
from the manufacturer.
- This device may only be operated with the speci-
ed lamps or their equivalents.
- If you have any questions about replacement
lamps, or for the correct use of this device, contact
the importer directly.
- Read the operating instructions before using the
device.
- This device must be operated with an external timer
as specied in chapter
Timer controlled operation .
NOTE: This device is intended to be used by only
one adult person at a time. Therefore, only one (1)
pair of protective eyewear is provided with each KBL
device.
BRIGHT LIGHT SENSITIVITY
This device emits very bright light primarily in the vis-
ible and near infrared ranges of the light spectrum.
• Wear protective eyewear that limits or reduces the
intensity of bright light and these wavelengths dur-
ing use.
• People who are sensitive to bright light should con-
sult a physician before using this device and exer-
cise caution during use.
FURTHER INSTRUCTIONS
• Follow all instructions given in this manual. In addi-
tion to that, observe all applicable statutory provi-
sions and regulations, also those applicable in the
country of operation.
• The device must only be connected by qualied,
trained and authorized service technicians.
• Arbitrary modications or conversions of the equip-
ment are not permissible.
• Observe all danger signals and safety signs
attached to the equipment.
• Safety signs must not be removed, and safety
appliances must not be disabled.
• The device may only be operated when in perfect
working condition.
• Never operate the device with the outer covering
removed or with the acrylic panes removed.
• Pay attention to the load limit of the oor plate
(tower devices only).
OPERATION IN CONJUNCTION WITH
VIBRANANO.
Any physical activity can strain the body.
To minimize user risk:
If you have any concerns or issues related to the use
of this device you shall consult a doctor before use.
3. Safety notes
Operating Instructions |KBL Tower beautyShaper 11

Operating Instructions |KBL Tower beautyShaper
12
3.2 Duties of the operator
The manufacturer cannot be held liable for damages or
injuries resulting from improper use of the equipment
or non-observance of these operating instructions.
Only use original spare parts, otherwise operating
authorization and terms of guarantee will become
invalid.
3.3 Intended use
This device is designed to vitalize the skin of an adult
person who is in full command of his/her physical,
sensorial and mental faculties. Moreover, sufficient
knowledge and experience are required.
If in doubt, consult a physician.
Stand in the middle of the booth, with body positioned
an equal distance from the surrounding lamps.
You must reach the interior control panel at all times
during the session.
Wear protective eyewear to reduce the bright light
during the session.
3.4 Indications for use
This product is an over-the-counter device emitting
very bright light primarily in the visible and near
infrared ranges of the light spectrum.
The correct use of this device can temporarily vitalize
the human skin.
The use of this device cannot replace treatment by a
licensed physician or healthcare professionals!
3.5 Contraindications
Any adult person listed here after may not use this
device.
• Persons under the age of 18 years.
• Persons with all forms of light sensitivity.
• Persons with disturbed feeling of warmth.
• Persons with heart pacemakers.
• People taking drugs that increase photosensitivity.
• People with light-sensitive skin areas.
• People whose skin has been chemically treated in
the last 48 hours.
• People whose skin has been burned by chemicals,
re, excessive UV radiation.
3.6 Warnings
• This product should not be used on individuals who
have had skin cancer or have a family history of skin
cancer.
• If there are special concerns about the light used in
this device consult a physician.
3.7 Foreseeable misuse
• The device shall be used only by one person at a
time.
• People with a body weight of more than 286 lb (130
kg) are not allowed to use the device.
• Any type of use that differs from the provisions
under the chapter Safety notes is considered mis-
use.
3.8 Misuse
• The use of lamps deviating from those dened from
the manufacturer is misuse.

Operating Instructions |KBL Tower beautyShaper 13
3.9 Timer controlled operation
This product must be operated with an external timer
that is listed in compliance with UL 917.
If the external timer fails, the device is automatically
switched off by an internal timer.
The maximum session time must not be exceeded.
Information on how to enter the ses-
sion time can be found in the operating
instructions of your external timer.
Accessory equipment connected to the analog and
digital interfaces must be certied to the respective
IEC standards (i.e. IEC 60601-1 for medical equip-
ment). Furthermore all congurations shall comply
with the system standard IEC 60601-1-1.
3.10 Guidelines for the use of
protective eyewear
Before use, the length of the elastic strap must be
adjusted to the required head size. For maximum
protection to elevate stray light, the eye protection
must t securely and comfortably on the eyelids. If
there is any stray light from the sides or under the
rim of the lens, DO NOT USE this eye protection. Ask
the staff to recommend an alternative eye protection.
Never use eye protection lenses that are broken,
cracked, bleached out, or otherwise damaged.
For cleaning the protective eyewear refer to chapter
Instructions on cleaning, disinfection and care .
3.11 Freeing a trapped person
Regardless of the operating state (stand by or in
operation) of the device, the door can be opened
manually from the inside or the outside easily and
with very little effort, any time.
The door drive mechanism is a purely mechanical
function that does not depend on electrical power.
3.12 Use of headphones
CAUTION
Hearing damage possible
Using headphones or earphones at high
volume may result in permanent hearing
damage.
• Do not set the volume too high.
3.13 Lamp breakage
CAUTION
Risk of mercury toxicity
Risk of mercury toxicity after a lamp
breakage. Please comply with the
following instructions:
• you must immediately disconnect the
device from the mains power.
• have children immediately leave the
room.
• you must ventilate the room for at
least 15 minutes.
• put on disposable gloves.
• open the window rst, then collect
the glass shards and escaped mer-
cury and put it into a sealable con-
tainer.
• bring the container to a collection site
for waste lamps.

Operating Instructions |KBL Tower beautyShaper
14
4. Description of the device
4.1 Standards
This device is in conformity with general requirements for basic safety and essential performance of medical
electrical equipment IEC 60601-1:2005 +A1:2012 and CAN/CSA-C22.2 No.601.1-M90) and the standards for
electromagnetic compatibility IEC 60601-1-2:2014 and EN 60601-1-2:2015 (EMC):
EN61000-3-2; EN61000-3-3; EN60601-1-2; EN55011; EN61000-4-2; EN61000-4-3; EN61000-4-4; EN61000-4-5; EN61000-4-6; EN61000-
4-8; EN61000-4-11.
According to CISPR 11 the electromagnetic emission characteristic of this device is classied in Group1 and
Class A.
The emission characteristics of this device make it suitable for use in industrial areas and hospitals (CISPR 11
class A). If it is used in a residential environment (for which CISPR 11 class B is normally required) this device
might not offer adequate protection to radio-frequency communication services. The studio operator might need
to take mitigation measures, such as relocating or re-orienting the equipment.
See EMC Tables according to IEC 60601-1-2:2014 and EN 60601-1-2:2015.
If, at any point, you determine that the ESSENTIAL PERFORMANCE of the device has been impaired (due to
electro-magnetic interference or other causes), then terminate installation / operation and consult the factory
before continuing.
Table 1
Guidance and Manufacturer’s Declaration - Electromagnetic Emission
The device is intended for use in the electromagnetic environment specied below. The studio operator of the
device should assure that it is used in such an environment.
Emission tests Compliance Electromagnetic environment - Guidance
RF emissions
according to CISPR 11 Group 1
The device uses RF energy exclusively for its internal
FUNCTION. Therefore, its HF emissions are very low and
not likely to cause any interference in nearby electronic
equipment.
RF emissions
according to CISPR 11 Class A
The device is intended for use in facilities other than residen-
tial areas, and for facilities that are directly connected to a
public low-voltage supply system that also supplies residen-
tial buildings.

Operating Instructions |KBL Tower beautyShaper 15
Table 2
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity to Interference
The device is intended for use in the electromagnetic environment specied below. The studio operator of the
device should assure that it is used in such an environment.
Immunity tests IEC 60601-
Test level Compliance level Electromagnetic environment - Guidance
Electrostatic discharge accord-
ing to IEC 61000-4-2
± 8 kV
contact discharge
± 15 kV
air discharge
+/- 8 kV
contact discharge
+/- 15 kV
air discharge
Floors should be made of wood or concrete
or be covered with ceramic tiles. If oors are
covered with synthetic material, the relative
humidity needs to be at least 30 %.
Fast transient electrical distur-
bances/bursts according to IEC
61000-4-4
± 2 kV
for power-supply lines
± 1 kV
for input and output lines
± 2 kV
for power-supply lines
± 1 kV
for input and output lines
Mains power quality should be that of a typi-
cal industrial or hospital environment.
Surge voltages (surges)
according to IEC 61000-4-5
± 1 kV
differential mode voltage
± 2 kV
common mode voltage
± 1 kV
differential mode voltage
± 2 kV
common mode voltage
Mains power quality should be that of a typi-
cal industrial or hospital environment.
Voltage dips, short interrup-
tions and voltage variations
on power-supply input lines
according to IEC 61000-4-11
Dips
0% for 1 cycle
70% for 25/30 cycles
Interrupts
0% for 250/300 cycles
Dips
0% for 1 cycle
70% for 25/30 cycles
Interrupts
0% for 250/300 cycles
Mains power quality should be that of a typi-
cal industrial or hospital environment.
If the studio operator of the device requires
continuous operation of the device even in
the event of interruptions of the power sup-
ply, it is recommended that the device is
powered by an uninterrupted power supply
unit.
Power-frequency (50/60 Hz)
magnetic eld according to IEC
61000-4-8
30 A/m 30 A/m
Power-frequency magnetic elds should be
at levels characteristic of a typical location in
a typical industrial or hospital environment.

Operating Instructions |KBL Tower beautyShaper
16
Table 4
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity to Interference
The device is intended for use in the electromagnetic environment specied below. The studio operator of the
device should assure that it is used in such an environment.
Immunity tests IEC 60601-
Test level Compliance level Electromagnetic environment - Guidance
Portable and mobile RF communications
equipment should be used no closer
to the devive, including cables, than
the recommended separation distance
calculated from the equation applicable to
the frequency of the transmitter.
Site the device a miniumum of 24 inches
from any other electrical / electronical
devices to mitigate electro-magnetic efforts
between devices
Conducted RF disturbances
according to IEC 61000-4-6
3 Veff
150 kHz to 80 MHz
10 Veff
150 kHz to 80 MHz
3 Veff
150 kHz to 80 MHz
10 Veff
150 kHz to 80 MHz Site the device a miniumum of 24 inches
from any other electrical / electronical
devices to mitigate electro-magnetic efforts
between devices
Radiated RF disturbances
according to IEC 61000-4-3
10 V/m
80 MHz to 1,0 GHz
10 V/m
1,4 GHz to 2,0 GHz
10 V/m
2,0 GHz to 2,7 GHz
10 V/m
80 MHz to 1,0 GHz
10 V/m
1,4 GHz to 2,0 GHz
10 V/m
2,0 GHz to 2,7 GHz
Field strengths from xed RF transmitters,
as determined by an electromagnetic site
survey ashall be lower than the compliance
level in all frequency ranges.
Interference may occur in the vicinity of
equipment marked with the following
symbol:
aField strengths from xed transmitters, such as base stations for radio telephones and land mobile radios, amateur radio,
AM and FM radio and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic envi-
ronment due to xed RF transmitters, an electromagnetic site survey should be considered. If the measured eld strength in
the location in which the device is used exceeds the applicable RF compliance level above, The device should be observed
to verify normal operation in every location of use. If abnormal performance is observed, additional measures may be nec-
essary, such as reorienting or relocating the device unit.
Table 6
Recommended separation distances between portable and mobile
RF communications equipment and the device
The device is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled.
Site the device a miniumum of 24 inches from any other electrical / electronical devices to mitigate electro-
magnetic efforts between devices.

Operating Instructions |KBL Tower beautyShaper 17
4.2 Components
The device basically consists of the following
components:
• Two side parts, comprising 12 tubes each.
• Rear part including 14 tubes.
• Door including 12 tubes.
• Top crown including interior control panel.
• Base plate.
• Fan casing.
1 Top crown with ventilation opening
2 Interior control panel
3 Fan casing
4 Exhaust opening
5 Supply connections
6 Lateral part, right-hand side
7Floor plate or vibraNano
8 Door
9 Door handles
10 Lateral part, left-hand side
11 Facing of unit lighting at top crow
⑨
⑩
⑧
⑪
③④②①
⑥⑤⑦

5.1 Class I ME equipment
WARNING
Risk of electric shock
To avoid the risk of electric shock, this
equipment must only be connected to a
supply mains with protective earth.
5.2 Overview supply connections
1
2
5
3
4
6
7
8
1 Mains voltage aquaCool box
2 Audio connection / channel selection
3 aquaCool - air (blue)
4 Aroma
5 aquaCool - liquid
6Connection of external timer (coin-box system)
7 Power supply
8 Data cable Tower/aquaCool box
5.3 Connecting the mains voltage
DANGER
Live parts
Risk of death or fatal injury due to electric
shock when touching live parts.
• Switch neutral
• Secure against reconnection
• Check for neutrality
• Ground and short-circuit
• Cover or shield any adjacent live parts or
components
Both the power supply and the related connection
work must comply with national standards and local
regulations. The connection work and replacement
of the power supply cord must only be performed
by qualied, trained and authorized service techni-
cians. The connection to the 3 x 220 V mains must
be protected by maximum over current protection.
For Canada a Class-A ground fault circuit interrupter
(GFCI) has to be used. Further information can be
found in chapter “Technical data”.
CONNECTION REQUIREMENTS
The electrical installation must be equipped with a
freely accessible all-pole disconnecting device in
accordance with the overvoltage category III. (Master
switch with clearly marked on/off settings e.g. “O”
and “I” or additional indicator light). The master
switch shall be tted externally on the side of the
booth, so the operator can access it at any time, even
when the device is in operation. This means that for
full separation each pole must have a contact gap
according to the conditions of the overvoltage cat-
egory III. The device shall be capable of being locked
in the off-position and shall comply with IEC 60447.
A supply main switch must not be incorporated in the
5. Connections
Operating Instructions |KBL Tower beautyShaper
18

Operating Instructions |KBL Tower beautyShaper 19
power supply cord.
A Class-A ground fault circuit interrupter (GFCI) has
to be used for Canada. Should the operation of the
device cause any interference in the power sup-
ply network, e.g. with ripple-control systems (TRA),
consult your power supply company to have corre-
sponding blocking elements (audio frequency sup-
pressors) installed.
GND
The device is by default set up to operate on 3 phases
but it can be changed over to 2-phase operation. The
wiring for 3-phase operation is shown below:









   





The wiring for 2-phase operation is shown below.
• Re-wire the 3 cables according to the diagram.
• Make sure that you use the right cable for the
power supply.



















   







5.4 Connecting an external audio
source
The cinch marked in the illustration is connected to
the external audio source where the line-out of the
sound player or the headphone/loudspeaker jack are
available for connection.
5.5 Level adjustment studio
music
The voice / audio system components are installed
in the back part of the device. The potentiometer
which serves to adjust the external audio signal
level is accessible through a maintenance hatch on
the left hand side of the device. To avoid overdrive,
select the level adjustment accordingly. The level
setting depends on the strength of the external signal
and should be carried out by qualied, trained and
authorized service technicians.

Operating Instructions |KBL Tower beautyShaper
20
5.6 Operation using different
audio sources
The audio source can be changed via the control
panel.
The device can be operated using the following audio
sources:
INTERNAL MP3 PLAYER
When using the internal MP3 player, you can either
play the music tracks that are originally supplied on
the SD card, or you can record your own tracks to
the SD card.
EXTERNAL AUDIO SOURCES - LINE IN
As an external audio source, you can connect
devices ranging from the standard-line level to low
loudspeaker levels.
These sources comprise:
• Studio music
• External players such as MP3 players, I-pods, etc.
• External Bluetooth players
EXTERNAL 100 V AUDIO SIGNAL ON STUDIO
CHANNEL (OPTIONAL FEATURE)
If you decide for a connection to a 100 V audio
system, you will need a transformer (KBL no.: 9100
0170 00) for the transmission of the audio signal.
This connection must be made by qualied, trained
and authorized service technicians.
EXTERNAL PLAYERS
A line connection has been integrated into in the
head area near the interior control Panel so that
the user can connect his or her own player such
as an MP3 player, an iPod, etc. Use a stand-
ard 3.5mm jack cable (included if the music
option has been ordered). Connect the jack plug
to the earphone jack of your player. Then select
”MP3 ext.” as the audio source from the inerior
control panel of the device before you start play-
ing your own tracks from the player. The tracks
can only be selected via the user’s own player.
The volume can be controlled via the control
panel of the device and also via the corresponding
operating elements provided by the user’s player.
5.7 Bluetooth connection
To connect an external player (smartphone etc.) wire-
lessly to the device an optional Bluetooth interface is
available.
CONNECT EXTERNAL PLAYER
A Bluetooth connection can be established in
standby and during operating mode.
Make sure that you are within the recep-
tion area (about 2 meters).
Make sure that your player is congured
to search for other Bluetooth devices.
Should this not be the case, enable
Bluetooth manually. To do so, please
read the instructions for your player.
• Depending on your settings the search will be
performed automatically or manually. All available
Bluetooth devices within reach will be listed after
a short time.
• Among the available devices choose “KBL Sound”.
In the service menu, a trailing number (01, 02, 03,
...) can be added to devices name.
• If necessary conrm the shown code and connect
again. Not every smart phone asks for a code.