ProSun LUXURA V8 User manual

8 MINUTES
Luxura V8 E 48 Ultra Intensive 230V
User Manual Model 48V8-E
MARK76V8002 Rev 4

2MARK76V8002 Rev 4
Contact Information
CONGRATULATIONS on your ProSun®purchase!
Please make sure you read this manual carefully before using this equipment and specifically
the maintenance schedule. Keep this manual available for future reference. If you have any
questions please contact ProSun directly.
ProSun International LLC
2442 23rd Street North
Saint Petersburg FL 33713
Toll Free: [phone]
Telephone: [phone]
Fax: [phone]
For all customer service related questions please contact our service department.
Toll Free: [phone]
WARNING!
ProSun has drawn up a maintenance schedule to ensure good
performance and maximum life of your unit. It is strongly recommended
to adhere to these service instructions and intervals. Always disconnect
the power before starting any maintenance work or cleaning!!
Read all the instructions thoroughly, failure to do so may result in:
• Serious death or injury
• Damage to the device or environment
WARNING: No modcation of this equipment is allowed.
For the safety of yourself and others around you please read all the
following instructions thoroughly. Please allow all operators of this
equipment to read these instructions.
COPYRIGHT
ProSun International LLC
The contents may not be duplicated (in whole or part), distributed or
utilized for competitive purposes without authorization or disclosed to
other parties. Changes cannot be made to the information herein.
WARNING!
WARNING!

3
MARK76V8002 Rev 4
Table of Contents
Important Customer Information ........................................................................... 5
Who Should Use, Read, & Understand this Manual ...................................... 5
Indications For Use ………….......…............................................................ 5
Intended Use .......….......................................….......................................... 5
Warning Signs & Symbols …................................................................................. 5
Preparing the Product For Use .............................................................................. 8
Export …....................................................................................................... 8
Transportation ….......................................................................................... 8
Delivery …..................................................................................................... 9
Ventilation ….................................................................................................. 9
Installation & Set-up …................................................................................. 9
Environmental Conditions for Transport & Storage ........................................ 10
EnviromentalConditionsforOperation...........................................................10
Comissioning of the Tanning Equipment …….......….....................……….. 11
General Safety Information ................................................................................... 12
General Safety Notes .......….......................................…............................ 12
Limits of Application …….......….........................................……………….. 12
The Tanning Process .................................................................................. 15
Exposure Schedule .................................................................…............... 15
Tanning Sensitivity ...................................................................................... 16
Equipment Components & Description …………………………….................... 17
Device Description ...................................................................................... 18
Options for Device ....................................................................................... 19
Lamp Conguration ……….......…............................................……………. 20
Dimensions ............................................................................................................ 21
Equipment Dimensions …........................................................................... 21
Recommended Room Size .......................................................….............. 21
Signs and Labels on Equipment ......................................................................... 22
Technical Data ....................................................................................................... 26
Electrical Specications ..................................................……................... 26
Electrical Requirements .....………………………...………………………..... 27
Electrical Connections …....……………………………………………………. 28
Tanning Bed Standards ....................................................................................... 29
Before Your Tanning Session ................................................................................ 33
Make-up & Cosmetics ...............................................................................… 33
Jewelry ........................................................................................................ 33
Hair & Loose Items ....................................................................................... 33
Medications ................................................................................................. 33
Contact Lenses ............................................................................................ 33
Showering & Hydrating the Skin ................................................................. 33
After the Tanning Session ..................................................................................... 34
Cleaning ...................................................................................................... 34
Cleaning the Acrylics .................................................................................. 34
Operation of the Equipment ............................................................................... 35
Obligations of the Business Operator …...................................................... 35
Sta󰀨 Training ….......................................................................................... 35

4MARK76V8002 Rev 4
How to Operate the Equipment ……………………………………………………….. 36
Choosing the Correct Exposure Time …………………………………………… 36
Normal Equipment Operation & Software …………………………………………… 37
Operating Modes ………………………………………………………………........ 37
Standby Mode ………………………………………………………...................... 37
Tanning Mode ………………………………………………………...................... 37
Cool Down Mode ………………………………………………………………........ 37
Service Mode ………………………………………………………………………… 37
Starting the Tanning Session ……………………………………………………...... 38
Stopping the Tanning Session …………………………………………………….... 39
Customer Concerns .................................……............................................................ 40
Storing the Device ....................................................................................................... 40
Decommissioning Your Tanning Unit ................................................................. 40
Storage ............................................................................................................. 41
Disposal ........................................................................................................... 41
ControlFunctions.........................................................................................................42
Indicator Lights ……………………………………………………………………… 43
Parameter Settings ............................................................................................ 46
Reading the Hour Counters & Software .............................................................. 48
Error Messages ……………………………………………………………………………… 49
Care & Maintenance .................................................................................................. 50
Basic Care Maintenance ……………………………………………………………. 51
Maintenance Schedule …………………………………………………………….. 51
Cleaning & Disinfecting Acrylics ............…………............................................. 52
Cleaning Plastic Surfaces ………………...………………………………………. 53
Cleaning Lamps …………………………….………………………………………. 53
Cleaning the Machine ……………………..………………………………………. 53
Maintenance by Skilled Persons …………………………………………………. 53
Troubleshooting Guide ............................................................................................... 54
Replacement of Components ……………….……………........................................... 55
Longevity of Acrylics ………………………………………………………………… 55
Longevity of Lamps ……………………………………………………………..…… 55
Disposal of Lamps …………………………………………………………………… 55
Technical Modications ……………………………………………………………... 55
Removing Acrylics ........................................................................................... 56
Replacing the Lamps ....................................................................................... 57
Lamp Replacement ………………………………………………………………… 57
Replacing the Xsens ………………………………………………………………. 58
Changing SoundAround Memory Cards …………………………………………. 58
Assembly Introduction …………...………………………………………………....…… 59
Included Parts ................................................................................................... 61
Assembly ......................................................................................................... 62
Adjusting the Doors ......................................................................................... 83
Warranty ....................................................................................................................... 84

5
MARK76V8002 Rev 4
Important Customer Information
Who should use, read and understand this manual:
• Owners - Owners are people that have this equipment in their business and have read and fully
understood this whole user manual. The owner is responsible for ensuring that any other person
who uses this equipment has also read and understood this user manual and labeling on the
equipment.
• Operator/User - People who are responsible for the operation, cleaning as well as general
maintenance care, as outlined in this manual, and who instruct the patients in the operation of
the equipment. All operators have fully read and understood this user manual and labeling on the
equipment.
• Patient - Any person that receives the tanning session.
• Service technicians- Certified technicians who will perform assembly and maintenance work on the
equipment and have fully read and understood the user manual and labeling on the equipment..
All people that will be operating this equipment need to fully read and understand these instructions and
all labeling on the equipment. A copy of the user manual should be readily available.This manual may
include features that are not included for your bed. Any service work outside of the preventative care table
in this manual should be done by a ProSun authorized technician.
This is a Class I ME Equipment, with Type B Applied Parts used for continuous use for a maximum of 8
minutes. The equipment is not intended to be sterilized or for use in an oxygen rich environment.
Warning signs and symbols
Danger and Safety Symbols:
Danger Hazard exists for human health.
DANGER!
WARNING!
WARNING: Hazard exists that can be dangerous to human health if instructions are
not followed properly.
WARNING : To avoid risk of electric shock, this equipment must only be connected
to a supply mains with protective earth.
WARNING: Care must be taken when operating this equipment around other
equipment to avoid reciprocal interference. Potential electromagnetic or other
interference could occur to this or to other equipment.Try to minimize interference
by not using other equipment in conjuction with this device.
WARNING: This equipment is designed to comply with IEC 60601-1-2. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with these instructions, may cause harmful
interference to other devices in the vincinity. However, there is no guarantee that
interference will not occur in a particular installation. Harmful interference to other
devices can be determined by turning this equipment ON and OFF. Try to correct the
interference using on or more of the following:
• Reorient or relocate the receiving device.
• Increase the separation between the equipment.
• Connect the equipment to an outlet on a di󰀨erent circuit from that to which the
other device(s) are connected and consult ProSun International LLC for help.
Intended use:
Tanning bed systems are intended to provide tanning of the human skin.
Indications for use:
Tanning bed Systems are intended to provide tanning of the human skin.

6MARK76V8002 Rev 4
Follow and read instructions thoroughly prior to using
equipment.
Caution Symbol means to proceed with caution and follow instructions carefully.
ESD-Sensitive devices, do not touch without using necessary proper
precautions.
Symbols found on equipment and packaging:
Keep equipment dry.
Fragile.
This way up.
Use only long forks on the fork lift and only lift on the correct
openings.
Atmospheric pressure limitation. This symbol is accompanied by
the upper and lower limits of atmospheric pressure for storage
and transportation.
Do not double stack. This symbol indicates that the items
shall not be vertically stacked, either because of the nature of
the transport packaging or because of the nature of the items
Temperature limit indicates the maximum and minimum
temperature limits at which the item shall be stored, transported
or used.
Humidity limitation indicates the acceptable upper and lower
limits of relative humidity for transport and storage.
High Voltage exists and is dangerous for human contact.
UV Radiation hazard for Human Health
Type B Applied Parts

7
MARK76V8002 Rev 4
Protective earth connections.
Recyclable Material
Polystyrene
Cardboard
20
Mixed Paper
50
FOR
Wood
PS
Waste of electrical and electronic equipment must not be
disposed as unsorted municipal waste. It must be collected
separately, and must be disposed as per local regulations.
Alternating Current. Single Phase
Three phase alternating current.

8MARK76V8002 Rev 4
Preparing the Product for Use
This equipment is in conformity with FDA standards 21 CFR 1040.20 for sunlamp products.
Export:
The device in this manual is intended for use in the United States and Canada. If this
equipment is exported to other countries, other standards may apply and not all information
in the operator manual may be applicable. ProSun does not assume any liability if there is
non-compliance outside of the intended sale territories of the United States or Canada. The
exporter assumes their own risk by removing this equipment outside of the United States or
Canada.
Transportation:
Equipment must be transported on the pallet on which it is mounted, and should not be double
stacked with other transport materials. If a forklift is used the long forks should be used and
only from the correct side. Only lift the load a few centimeters and move it to the place of
installation.
CAUTION - If the short forks are used damage may occur.
If a forklift cannot be used then the device must be partially disassembled from the pallet for
transport. Installers or persons transporting the equipment may want to use a dolly to move
the disassembled components but be careful of the weight. Each piece should be moved
individually to the place of installation.
During transportation environmental conditions must be met, ambient an ambient temperature
range of - 40 °C to + 70 °C or -40°F to 158°F, relative humidty range of between 10 to 95%
including condensation and atomospheric pressure range of 50 kPa to 106 kPa.
If ambient temperature change is di󰀨erent from required temperature then let equipment sit at
proper temperature for at least 2 hours prior to installation.
- 40 °C
70 °C
10%
95%
50kPa
106kPa

9
MARK76V8002 Rev 4
Delivery:
Once equipment is delivered make sure proper temperatures, humidty and atmospheric
pressure are in place.
The following items are included in the delivery:
• Tanning equipment
• Protective goggles
• Tanning bed cleaner
• All parts in assembly manual
• User Manual
Note that equipment is delivered through third party freight company. Equipment will not
be brought inside the building by freight company unless prior arrangements are made.
Coordinate with ProSun installation department to set up delivery and installation details.
In a commercial setting an external timer is required. ProSun recommends to use this
accesory (T-Max Flushmount G2).
Ventillation:
The Device must always have proper ventilation. Failure to do so can cause in serious
safety hazards and overheating of the equipment.
DANGER!
Installation and Set-up:
Equipment should only be installed in dry rooms with proper ventillation and airing. The room
should be the recommended size of 8 x 7 ft in order to allow for good air ow.
The unit should not be set up in a mobile environment or facility, i.e. trains, buses, ships. The
unit also should not be used outdoors, if used outdoors damage to the equipment is possible
and the manufacturer will not be held liable
Before starting the installation process or operating the equipment the transportation pallet
should be removed. Observe correct room sizes prior to installation the equipment and ensure
that room has correct electrical speccations. The customer must have provided a dedicated
power source when called for in the technical speccaitions of the unit.
Environmental conditions for transport and storage:
• Relative humidty range of 10% to 95% including condensation.
• Atmospheric pressure range of 50kPa to 106 kPa.
• Storage temperature range: -40 °F (-40 °C) and 158 °F (70 °C)
• Let equipment sit for at least 2 hours if range was outside of ambient
temperature range.
Environmental conditions for operation:
• Relative humidty range of 30% to 75% including condensation.
• Atmospheric pressure range of 50kPa to 106 kPa.
• Optimum ambient temperature range: 50°F (10°C) and 86 °F (30°C)

10 MARK76V8002 Rev 4
Installation can present a Danger with electrical shock or burns, only authorized personnel
should install the equipment. Initial installation should be done by a ProSun certied
technician. As the equipment owner it is your responsibility to ensure that correct electrical
requirements are met and followed.
Overheating can occur if proper ventilation is not followed. Never obstruct the airways in the
inow and outow areas. If proper ventillation is not followed system malfunction and damage
may occur. Always install the unit at proper distance from walls in order to have proper airow.
Failure to do so may cause system failures or errors.
The customer is responsible for all costs associated with the preparation of the installation
of the equipment. This includes but is not limited to room preparation, costs, fees, permits,
and inspections unless specied otherwise in the sales order for the equipment purchased.
ProSun and all authorized parties shall reserve the right to refuse to install equipment into any
room which has not been properly prepared in accordance with the electrical specication and
room requirements.
The electrical contractor or his designee shall provide and install all electrical material as
specied for a safe operating system. ProSun certied technicians will not perform any
electrical work. The recommended electrical plan must be coordinated between the customer
and the electrical contactor. Any deviation of the electrical, before, during and after equipment
installation is the responsibility of the customer. The electrical contractor or his designee shall
ensure the completion of all electrical requirements prior to the installation of any ProSun
equipment. All wires shall be single solid runs without splices, meeting NEMA standards.
The electrical contractor or his designee should ring out, tag and terminate all wires at both
ends. Each should be inspected to ensure that no wires have been grounded or are left
open. ProSun certied technicians are not responsible for the nal installation of the electrical
system, the electrical contractor or his designee should be present to make the nal electrical
connection upon completion of the installation of the equipment.
The customer shall bear the sole responsibility for compliance with all applicable codes,
OSHA, NEMA, local and national Standards. All electrical work shall conform to the
requirements of the national electrical code, OSHA or applicable local and or state
ordinances.
WARNING: Position the equipment so that disconnection to the mains circuit breaker can be
easily made during the unexpected error which could lead to a hazardous situation.
WARNING: Power supply cord must be replaced by ProSun certied technician.
WARNING: Inspect equipment for any obvious physical damage before use.
DANGER!
WARNING!
WARNING!
WARNING!

11
MARK76V8002 Rev 4
The equipment is initially commissioned by a certied ProSun technician. The device will
be properly assembled and handed over ready for us. In order to properly commission the
tanning equipment, the business owner must ensure that the location is ready prior to the
equipment being installed. This included having correct power requirements and having the
room in which the unit will be located ready.
The unit incorporates special preventive measures with regard to the electromagnetic
compatibility and must be installed and commissioned according to the EMC instructions
obtained from the assembly instructions.
If the equipment has not been used for a longer period of time, then it must rst
be inspected by a certied technician before being put back into operation again.
Commissioning of the tanning equipment

12 MARK76V8002 Rev 4
General Safety Information
General Safety Notes:
Any adult with any of the below issues should not use this tanning equipment. If you are
unsure consult your doctor prior to use.
Contraindication: This sunlamp product is contraindicated for use on persons under the
age of 18 years.
Contraindication: This sunlamp product must not be used if skin lesions or open wounds
are present.
Contraindication: This sunlamp product should not be used on individuals who have had
skin cancer or have a family history of skin cancer. People repeatedly exposed to ultraviolet
sunlamp products should be regularly evaluated for skin cancer.
Contraindication: People with Skin Type I, who are prone to sunburn should not use this
equipment, or had several sever sunburns as a child. People who are already su󰀨ering from
sunburn should not use this equipment until the sunburn is completely gone and they can
properly evaluate skin type and calculate their exposure schedule.
Contraindication: People taking photosensitive medications, medicines, or people who are
being treated by a doctor for conditions related to photosensitivity.
Contraindication: Peope who wear a heart pacemaker.
Contraindication: People are who are prone to freckles, or people with naturally red hair
color.
Contraindication: People who have atypical discolored skin areas and/or with more than
ve atypical moles with a diameter of 5 milimeters. People with more than 16 moles with a
diameter greater than or equal to 2 milimeters. If you are unsure consult your doctor prior to
your tanning session.
Contraindication: People who do not tan at all or cannot tan without getting a sunburn.
Limits of Application:
Never operate this unit when the ambient room air temperature is greater than 104 degrees
faranheit.
Never operate this unit in a commercial setting when the remote timer is not working properly.
Always disconnect the unit from its power supply when servicing or repairing the unit.
WARNING!

13
MARK76V8002 Rev 4
Allow at least 48 hours to pass between each tanning session. Tan based on the exposure
sticker on the unit or in this manual. Skin Type I should not tan. As an owner you must
properly instruct all users on using the exposure table located on the front of the bed and
only tanning for the minutes based on their skin type. If any negative e󰀨ect occurs, stop using
the equipment and consult a physician.
If you are taking any kind of medication make sure to rst consult consult your doctor before
tanning. Certain ingredients in medication can induce UV light sensitivity and cause allergic
reactions. A table describing a number of known allergens can be seen later in this manual.
For best facial tanning results make sure to remove all facial cosmetics thoroughly prior to
each session. Best results may occur if no cosmetics are used 3 hours or even the day of the
tanning session. If certain cosmetics are used you may experience a UV light sensitivity that
could cause an allergic reaction. See the table in this manual describing a number of known
allergens later in this manual.
Do not use tanning lotions, oils or gels that contain SPF ( sun protection factor) as these
could hinder the desired tanning e󰀨ect and may not have the same protection with tanning
equipment as with natural sunlight. Use only those that are speccally manufactured for use
in tanning beds.
If your skin develops or displays any sort of undesired reaction such as a rash, acne, or
unusual dryness you should stop tanning immediately and consult your doctor.
Always avoid sunburn. If you overexposure yourself you could get a sunburn on your skin.
Should this occur, stop tanning and wait for the reddish color to subside before recalculating
your exposure schedule and resuming treatment.
Read the WARNING and DANGER label situated in full view of the user on the tanning bed
before beginning your tanning session.
Never use tanning accelerator pills in conjunction with your tanning treatement as these
could lead to an increase of skin sensitivity and sunburn.
Always wear protective eye wear.
Only (1) one tanner per session is allowed in the equipment.
The manufacturer cannot be held liable for damages or injuries from improper use of the
equipment or non-observance of the operating instructions.

14 MARK76V8002 Rev 4
This tanning bed is an over the counter tanning device that emits ultra violet light in the
UVB and UVA region of the spectrum intended for the cosmetic tanning of the human skin in
adults.
Only one user should tan in the unit at a time.
Wear protective eyewear during the duration of the sesion to protect the eyes against UV
radiation. Only use approved protective eyewear. Using the equipment without protective
eyewear may in eye injury or diseases. The unprotected eye can become inamed on the
surface, and in certain cases the retina can be damaged by exces-sive radiation. Cataracts
can form after repeated exposure to radiation.
You should not modify your equipment as it may cause serious injury or damage to your unit.
Infections can be transfered through skin contact, the unit should be properly cleaned after
every use. All items that the user can come in contact with shall be properly cleaned and
disinfected after every session. This includes but is not limited to:
• Goggles
• Base oor (when applicable)
• Acrylics
• Handles and control panel
• MP3 cable (when applicable)
• Headrest
Use only approved cleaner such as Lucasol One Step to clean and disinfect the tanning unit.
Long term consequences can exist if proper precaution is not taken.
• Over exposure should be avoided.
• Elderly people should not use this equipment without consulting their physician rst.
• Children under the age of 18 cannot use these tanning deivces.
• It is recommended that expectant mothers do not use these devices. While there are
no clinical studies of negative e󰀨ects of tanning with expectant mothers it is still not
recommended.
This is a commercial grade tanning bed.

15
MARK76V8002 Rev 4
The tanning unit you have purchased is designed to concentrate optimal levels of UVA, in
conjunction with very low percentages of UVB, on the outermost layers of the skin, so as to
stimulate the production of Melanic pigment, which is slightly pink in its dormant state, these
causes it to turn brown after excretion. The more Melanin cells present in the skin determines
the amount of pigment that will be excreted and distributed, and therefore the extent of the
tan.
UVA has a higher frequency of wavelength than UVB or UVC, and is the ray which is
thought to promote the excretion of pigment from the hormone called “Melanin”, which occurs
naturally in the skin.
UVB is believed to be the catalyst, or kick-starter for the Melanin to begin producing
pigment. It is also the ray which causes sunburn and wrinkling, so the skin can withstand only
brief dosages at very small percentage levels to UVA.
UVC, present in natural sunlight, is mostly ltered out by the ozone layer in the upper
atmosphere, and is extremely harmful to human skin, at any level of exposure.
In tanning beds, only small percentages of UVB to UVA are used to e󰀨ect tanning - example:
95% UVA-to-5% UVB - whereby the individual tanner will be placed on an acceptable
exposure schedule according to his or her skin type. There is no UVC emitted by tanning
lamps.
Do not tan more than once every 48 hours. Depending on skin type, tanning sessions, each
consisting of 10 to 12 individual sessions to create the base tan should be done continuously.
However, no more than 3 of these treatments per week should occur. For more in depth
detail on the tanning schedule see our exposure sticker on the unit and in this manual.
SKIN TYPE I - This individual burns easily and should NOT tan.
SKIN TYPE II - This individual burns easily and severely and should tan minimally.
SKIN TYPE III - This individual burns moderately and tans moderately.
SKIN TYPE IV - This individual burns minimally and tans well/ above average.
Exposure Schedule:
The Tanning Process

16 MARK76V8002 Rev 4
Tanning Sensitivity
*The following may increase skin sensitivity:
• Perfumes and colognes containing furocoumarins.
• Compounds from natural products such as plants and fruits (their natural oils can sensitize
the skin to sunlight.
• Food and fruits that contain photosensitizing agents: celery, carrots, lime, coriander,
parsley, fennel, dill, buttercup, mustard and gs.
A partial list of known photosensitizing medications is listed below by name:
Before using a tanning device always check with your doctor rst.
ACETOHEXAMIDE (DYMELOR)
ACRIDINE PREPARATIONS (SLIGHT)
AGAVE LECHUGUILLA (AMARYLLIS)
AGRIMONY
9-AMINOACRIDINEAMINOBENZOIC ACID
AMITRIPTYLINE (ELAVIL, ETC.)
ANESTHETICA (PROCAINE GROUP)
ANGELICA
ANTHRACENE
ANTIMALARIALS
ARSENICALS
BARBITURATES
BAVACHE (CORYLIFOLIA)
BENEZENE
BENZOPYRINE
BERGAMOT (PERFUME)
BITHIONAL (ACTAMER, LOROTHIDOL)
BLANKOPHORES (SULFA DERIVATIVES)
BULOSEMIDE (JADIT)
BROMCHLORSALICYLANILID
4-BUTYL-4-CHLOROSALICYLANILIDE
CARBAMAZEPINE (TEGRETOL)
CARBINOXAMINE D-FORM (TWISTON
R-A)
CARBUTAMIDE (NADISAN)
CARROTS, WILD CEDAR OIL
CELERY
CHLOROPHYLL
CHLOROTHIAZIDE (DIURIL)
CHLORPROMAZINE (THORAZINE)
CHLORTETRACYCLINE (AUREOMYCIN)
CITRON OIL
CITRUS FRUITS
CLOVER
COAL TAR
CONTRACEPTIVES, ORAL
DEMECLOCYCLINE
DECLOMYCIN
DIMETHYLCHLORTETACYCLINE
DESIPRAMINE (NORPRAMIN,
PERTOFRANE) DIBENZOPYRAN
DERIVATES
DICYANINE-A
DIETHYLSTILBESTROL
DIGALLOYL TRIOLEATE SUNSCREEN
DILL
DIPHENHYDRAMINE HYDROCHLORIDE
EOSIN (SLIGHT)
ESTRONE
FENNEL FLOURESCEIN DYES
5-FLOUROURACIL
GLYCERYL P-AMINOBENZOATE
GOLD SALTS
GRASS (MEADOW)
GRISEOFULVIN (FULVICIN)
HEMATOPORPHYRIN
HEXACHLOROPHENE (RARE)
HEXACHLOROTHIAZIDE (ESIDRIX)
IMIPRAMINIE HCL (TOFRANIL)
ISOTHIPENCYL (THERUHISTIN)
ISOTHIPENDYL
LADY’S THUMB (TEA)
LANTININ
LAVENDER OIL
LIME OIL
MECLOTHIAZIDE (ENDURON)
MEPAZINE (PACATAL)
9-MERCAPTOPURINE
METHOTRIMEPRAZINE (LEVOPROME)
METHOXSALEN (MELOYINE,
OXSORALEN)
5-METHOXYPSORALEN
8-METHOXYPSORALEN
MONOGLYCERAL PARA-
AMINOBENZOATE MUSTARDS
NALIDIXIC ACID
NAPTHALENE
NORTRIPTYLINE (A VENTYL)
OXYTETRACYCLINE (TERRAMICIN)
PARA-DIMETHLAMINOAZOBENZENE
PARAPHE NYLENEDIAMINE
PARSLEY
PARSNIPS PENICILLIN DERIVATIVES
PERIOLINE
PERPHENAZINE )TRILAFON)
PENANTHRENE
PHENAZINE DYES
PHENOLIC COMPOUNDS
PHENOTHIAZINES (DYES, METHYLENE
BLUE)
PHENOXAZINES
PHENYLBUTAZONE (BUTAZOLIDIN)
PHENYTIOIN (DILANTIN)
PITCH AND PITCH FUMES
PORPHYRINS
PROCHLORPERAZINE
PROMAZINE HYDROCHLORIDE
PROFRIPTYLINE
PSORALENS
PYRATHIAZINE HYDROCHLORIDE
PYRIDINE QUINETHAZONE (HYDROMOX)
QUYININE ROSE BENGAL PERFUME
RUE
SALICYLANILIDES SALICYLATES
SANDALWOOD OIL (PERFUME)
SILVER SALTS
SMARTWEED (TEA)
STILBAMIDINE ISETHIONATE
SULFACETAMIDE SULFADIAZINE
SULFADIMETHOXINE
SULFAGUANIDINE SULFANILAMIDE
(SLIGHT) SULFAMERAZINE
SULFAMETHANIZINE
SULFAPYRIDINE
SULFATHIAZOLE
SULFONAMIDES
SULFAISOMIDINE (ELKOSIN)
SULFONYLUREAS (ANTIDIABETICS)
TETRACHLORSALICYLANILIDE
TRETACYCLINES THIAZIDES
(DIURIL, HYDRODIURIL)
THIOPHENE
THIOPROPAZATE DIHYDROCHLORIDE
TOLBUTAMIDE (ORINASE)
TOLUENE
TRIBROMOSALICYLANILIDE (TBS)
TRICHLORMETHIAZIDE
(METHAHYDRIN) TRIDIONE
TRIETHYLENE MELAMINE (TEM)
TRIFLUPROMAZINE HYDROCHLORIDE
(VESPRIN)
TRIMEPRAZINE TARTRATE (TEMARIL)
TRIMETHADIONE (TRIDIONE)
TRIPYRATHIAZINE
TRYPATLAVINE
TRYPAN BLUE
VANILLIN OILS
WATER ASH
XYLENE
YARROW

17
MARK76V8002 Rev 4
Components
The tanning device consists of 4 panels ( 2 main panels and 2 door panels)
and a control column in the center.
In the diagram above, the di󰀨erent components have been outlined and
described. Not all components are available in every country.
XL Light for Extra long 2
meter lamps.
The fading color ow
gives extra luxury to
your unit.
3 step body cooler
Sound system with
pre-installed speakers, 2
music channels and mp3
integration.
Touch Screen
Raised Floor
Before using a tanning device always check with your doctor rst.

18 MARK76V8002 Rev 4
DeviceDescription
1. Left side panel
2. Right side panel
3. Left door panel
4. Right door Panel
5. Ceiling with cooling fan
6. Base/Floor
7. Center column/control panel
8. Options
9. Door handle
10.Accent Lighting

19
MARK76V8002 Rev 4
Options for Device
1
1
1. Accent/Ambient Lighting
2. Mp3/Headphone connection
3. Loud speakers
4. Sound cards (SD Cards)
2
3
4
The below items are options for this device and may not be included in your unit.
These options do not a󰀨ect the normal functioning of your device.

20 MARK76V8002 Rev 4
Lamp conguration- The use of non approved UV Lamps
voids the warranty!
Luxura V8 48 E Ultra Intensive
Quantity Name Length Watts Part Number
A 7 ProTech II Ultra Intensive
R-UVA 200w XL-E
79" inches
2 Meters
200W LAMP7670107
B 17 ProTech II Ultra Intensive
R-UVA 200w XL-E
79" inches
2 Meters
200W LAMP7670107
C 17 ProTech II Ultra Intensive
R-UVA 200w XL-E
79" inches
2 Meters
200W LAMP7670107
D 7 ProTech II Ultra Intensive
R-UVA 200w XL-E
79" inches
2 Meters
200W LAMP7670107
Luxura V8 48 E Ultra Intensive - Spare parts
Acrylic Panel ACRY4013553
Acrylic Door Panel ACRY4013558
Goggles ACCE2501629