KDS Models Chase 360 User manual

200mm
688mm
90mm
Centre of Gravity
96mm
814mm
Page. 1

1
Main belt (147MXL-9MM)
Lower motor block
18T 2nd Stage pinion
1ST Stage pulley pin
Page. 2
2
3
4
5
6
7
8
9
10
11
ITEM NO. DESCRIP TION QTY.
1 1
28
3 1
41
51
6 1
72
8
9
10
11
1
1
1
1
Round head screw(M2.5 x 6)
Bearing (4x10x4)
Motor mount bracket right
Motor mount bracket left
Upper motor block
50T Pulley
1ST Stage belt (63MXL-6mm)

0.5mm MIN
0.5mm MIN
Turn the motor over by hand to test belt positioning.
Adjust the motor pinion height until the belt runs
central on the front pulley
Make sure your motor has
a flat ground on the shaft
for the pinion grub screw.
This step can be completed at any time.
But is easier before installing the 1st stage assembly into the model
2
13
4
Set Screw (M3)
Flat head screw M3X6
Motor(1880KV)
pinion 18T(19T )
1
2
1
1
ITEM NO DESCRIP TION QTY.
1
2
3
4
Page. 3
tip : the pinion should be positioned as
close as possible to the top plate
to avoid rubbing and correct belt
alignment

Bearing (3x7x3)
Belt guide pulley
spacing washer
Page. 4
GYRO TRAY
Boom Clamp
STEP 4
1
2
4
6
3
71
2
3
4
5
ITEM NO. DESCRIP TION QTY.
1 1
24
3 2
42
51
6 4
72
ITEM NO. DESCRIP TION QTY.
1 1
24
3 2
42
CAP Screw (M3 x 24)
UP Pulley holder SET
Spacer sleeve
Down Pulley holder SET
Flat head screw M2.5X6

15mm Nominal
Tip - It is best to position the servo arms on servos
(with 0 trim) closest to level during this step.
6
4
Long side of the
brackets face
clockwise.
CYCLIC SERVO
Lock Nut (M2)
UPPER BEARING BLOCK
Bearing (8x16x5)
SERVO MOUNT
LOWER BEARING BLOCK
Page. 5
1
2
3
4 5 6 7
12
ITEM NO. DESCRIP TION QTY.
1 6
23
3 6
46
54
6 1
73
ITEM NO. DESCRIP TION QTY.
1 1
21
Round head screw (M2 x 6)
Round head screw (M2.5 x 6)
Bearing (8x16x5)
Power the servo to adjust the central
point at level condition before assemble

Recommended lipo 1200 - 1400 mah.
Size restrictions 39mm x 45mm x 116mm.
Or unlimited length with front tail servo
mount option (Refer to Step 26)
Mirror this step for
Left side frame.
Lipo tray button (right)
Side frame
LIPO 1200 - 1400mAh
Page. 6
1
2
4
3
1
2
4
3
Round head screw (M2 x 4)
ITEM NO DESCRIP TION QTY.
1 1
2 3
3 1
4 1
canopy locating pin
ITEM NO DESCRIP TION QTY.
1 1
2 2
3 1
4 1
Flat head screw M2.5X6
Lipo tray
Lipo tray fixed mount

ITEM NO DESCRIP TION QTY.
1LANDING GEAR - LEFT 1
2LANDING GEAR - RIGHT 1
3LANDING GEAR MOUNT 2
4 FROM STEP 6 1
5 8
Page. 7
lock the screws only after main
frame left is well-assembled.
1234
5
CAP Screw (M2.5 x 8)

FROM STEP 5 1
FROM STEP 2 1
FRAME SPACERS 2
Lipo sliding rail (right)1
Round head screw (M2 x 4) 2
2
Page. 8
CAP Screw (M2.5 x 6) 5
1
2
3
4
5
ITEM
NO. DESCRIP TION QTY.
1
2
3
4
5
6
7
6
7
CAP Screw (M2.5 x 8)
8
Frame Washer (Red) 7
8

1
2
4
3
5
6Ensure no free play in the
tail shaft by fastening the Locking collar
and pinion against the bearings.
Tail shaft
Tail shaft locking collar
Tail Pinion (15T)
Set Screw (M3x3)
Tail Box
Bearings (4x8x3)
Page. 9
1
1
2
1
1
2
ITEM NO DESCRIP TION QTY.
1
2
3
4
5
6

Tip: Tighten Screws in a few
stages to ensure the bracket
remains parallel with the tail shaft.
Refer to step 25 for details.
ITEM NO. DESCRIP TION QTY.
1
Fin Spacer 1
2Tail Boom 1
3 2
4
Pitch Slider Bracket 1
5
Tail Belt 1
6 1
7 1
8 1
9
Tail control guide 2
10 1
11 1
Page. 10
11
1 2
345
8
7
6
10
9
12
12 2
CAP Screw (M2 x 10)
CAP Screw (M2 x 4)
CAP Screw (M2 x 6)
CF Vertical stabilizer
Tail boom brace mount
Heat shrink tubing
CAP Screw (ST2 x 6)