KegLand KL1839 User manual

Label Applicator Machine Instruction Manual
Page 1of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
Label Applicator Machine
Instruction Manual
KL18319
KegLand Distribution PTY LTD
www.KegLand.com.au

Label Applicator Machine Instruction Manual
Page 2of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
Initial Setup
Step 1. Attach the paper tray bracket to the Label applicator machine with the three small screws provided.
Step 2. Assemble the paper tray as shown below and secure the position of the two perspex disks with a
socket head screw, to secure the paper roll in place between the Perspex disks.
WARNING
DO NOT PLACE ANY BODY PARTS NEAR ANY MOVING PARTS WHILE THE
MACHINE IS PLUGGED IN. ENSURE THE MACHINE IS UNPLUGGED BEFORE
PLACING ANY BODY PARTS CLOSE TO ANY MOVING PARTS

Label Applicator Machine Instruction Manual
Page 3of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
Step 3. Feed paper through the machine in the direction of the red line as shown below:
1. Feed the label under the guide rod and adjust the guide disks according to the height of the label
Guide rod
Guide disks

Label Applicator Machine Instruction Manual
Page 4of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
2. Feed the label under the transition roller and up the peeling plate
3. Feed the label over the peeling plate, behind the first soft pull roller and then between the second soft
pull roller and the knurled pull roller. Then feed the label back underneath the knurled pull roller.
The gap between the second soft pull roller and the knurled pull roller can be opened by
unscrewing the wing nuts underneath the knurled pull roller to make it easier to feed the
paper between two. The wing nuts can then be tightened and the second soft pull roller
rotated to feed the label through these two rolls and underneath the knurled pull roller.
Transition roller
Peeling plate
Peeling plate
Second soft pull roller
Knurled pull roller
First soft pull roller

Label Applicator Machine Instruction Manual
Page 5of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
4. Feed the label over the feed roller and secure in place with the clip
Step 4. Move the position of the sensor according to the label width.
It is suggested that a small section of adhesive is visible at the pressing can roller as shown below to
make it easier to determine where the can should be placed on the can support roller and labelling
soft roller.
The peeling plate should be as close as possible to the labelling soft roller, but not touching.

Label Applicator Machine Instruction Manual
Page 6of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
Step 5. Adjust the distance between the support roller and labelling soft roller according to the diameter of
the can. Also adjust the position of the pressing roller on the swing arm so it sits centrally above the can.
After adjusted, tighten the wing nuts.
Step 6. Adjust the amount of thread showing on the touch rod screw such that the microswitch is activated
just before the pressing roller touches the can. Activation of the microswitch can be identified by an audible
clicking sound.
Touch rod screw
Adjust the amount of thread showing here to alter when the microswitch is activated
Pressing roller
Support roller
Labelling soft roller

Label Applicator Machine Instruction Manual
Page 7of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
Operation
1. Place a can on the support roller and labelling soft roller
2. Align the can with the label
3. Pull the swing arm down until the pressing roller touches the can
4. Hold the swing arm down until the label is applied
5. Return the swing arm to its original position and remove the labelled can.
Calibration of sensor
1. Load a label onto the paper tray and feed through the machine and attach to the feed roller.
2. Align the sensor with the white gap between the labels.
3. Press set.
4. Move the label under the sensor until the highest number is displayed on the screen.
5. Press set again at the position on the label which displays the highest number.
NOTE: the numbers displayed on your screen may be significantly different to the numbers on the
images above.

Label Applicator Machine Instruction Manual
Page 8of 8www.KegLand.com.au Last Updated 28/09/2020 11:52 AM
Warranty and Support (Australia)
The Label Applicator Machine comes with a 1 year warranty when sold in Australia.
To lodge a warranty claim in Australia please forward as many visual pieces of supporting
information and a detailed description of your issue to
If you purchased your unit from a distributor in Australia or internationally, you will be required to
go through their warranty claims process.
For a full terms and conditions, please visit our website here -> Terms & Conditions
For technical support with the Label Applicator Machine please email