Keis Heated Hi-Power BodyWarmer User manual

Keis Heated Clothing is istribute in the UK by
Motohaus Powersports Limited PO Box 7092 Hook RG29 1TY
www.motohaus.com Email: [email protected]
In the interests of pro uct improvement we
reserve the right to make technical an
esign changes without notice.
www.keisapparel.co.uk
O P E R A T I N G I N S T R U C T I O N S
Heated appare for
outdoor activities
111
WARNING: To ensure safe operation follow these instructions
carefully and keep them in a safe place for future reference.
HI-POWER
HEATED
BODYWARMER
Visit
WWW.KEISAPPAREL.CO.UK
to see the full range of Keis Heated Apparel
and Accessories – All designed to
help you stay out longer!
CARE OF YOUR KEIS HI-POWER BODYWARMER
IHand wash at 30°C and drip
dry only.
IDo not tumble dry or wring.
IDo not iron.
IDo not bleach.
IDo not operate until completely dry.
TECHNICAL DATA
Shell: 94% Polyester, 6% Spandex
Li i g: 100% polyester
Voltage: 12V Only
Approximate Curre t Draw: 3.3A
Typical Power: 39W
H E A T E D A P P A R E L F O R O U T D O O R A C T I V I T I E S
Keis_A5_hi-power-bodywarmer V 2014

+
–
Fused Connection Lead
USING A TEMPERATURE CONTROLLER
NOTE: For ultimate comfort this garment is best controlled by a eis Temperature
Controller. Ask your dealer for details or visit www.keisapparel.co.uk.
Open the Controller Pocket and locate and remove the link wire from the connection block and replace
with the Controller. When using the garment without the Controller simply unplug the Controller and
reconnect the link wire to the connection block inside the
Controller Pocket.
NOTE: The Link Wire or a Controller must be in place for the garment to heat.
SAFETY & ENVIRONMENT FIRST
Do not dispose of electrical equipment with standard domestic waste.
Contact your local authority for disposal information specific to your area.
WARNING
IThis electrically heated garment must be used strictly in accordance with the
manufacturer’s instructions. Failure to observe this notice may lead to increased risk of
burns and fire resulting in injury or death.
ISwitch the garment off immediately and check the affected skin at any sign of irritation
or sensation of excessive heat.
IDo not use the garment when wet. If it becomes wet during use disconnect
immediately from the power source.
INever leave the garment unattended when switched on.
IAlways wear clothing between the heated garment and the skin. Do not wear directly in
contact with the skin.
IThis product is unsuitable for young children.
IDo not use this product if you suffer from: heightened or impaired temperature
sensitivity; an inability to sense temperature extremes; circulatory problems resulting
from diabetes or other medical conditions.
IUse this product with 12V systems ONLY.
IAlways observe the correct fuse rating – See ‘Manage your Fuses’.
IDo not modify or disassemble any part of the system in any way.
IDo not use if the product is visibly damaged.
HI-POWER
HEATED
BODYWARMER
Link Wire
Connector Block
Auxiliary Power
Socket for use
with eis 12V
Gloves ONLY
Auxiliary Power
Socket for use
with eis Insoles
or Trousers
Pocket containing 12v Supply Lead
Outside of garment
Inside of garment
Power Input Lead
for Heat Controller
(not supplied) in
the exterior
Controller Pocket
Do not operate the controller whilst driving!
Keis_A5_hi-power-bodywarmer V 2014
MANAGE YOUR FUSES
WARNING For your safety it is essential to manage
the fusing to your eis Heated Apparel.
A selection of up to fLYHfuses is supplied depending on
the current drain and potential combinations of the
garments.
On delivery the fuse holder in the supply loom may be
delivered without a fuse. To calculate the fuse value
required simply add the current draws for each of the
garments supplied by the 12V Supply Loom and use
the lowest rated fuse that exceeds the calculated
current.
NOTE: A fuse value below the value required may fail
in use.
FOR EXAMPLE: Sleeved Jacket consumes 7A, Insoles
consume 1.3A. Therefore total is 8.3A. Next fuse value
above this is 10A so use a 10A fuse.
PREPARING A VEHICLE TO POWER YOUR KEIS HEATED GARMENT
Your eis heated garment is designed to be powered from a 12V source such as a vehicle battery or
Lithium Battery Pack.
To power your eis garment from a vehicle battery attach the Fused Connection Lead directly to the
battery or other live 12V source taking into account any safety notices issued by the vehicle
manufacturer and observing the polarity Red +ve and Black -ve.
Position the power socket so it is in a convenient position to power your garment and secure if necessary
using cable ties or tape ensuring that it cannot become trapped, damaged or interfere with the normal
operation of the vehicle.
WARNING Always connect the Red +ve lead to the battery first.
POWERING YOUR KEIS GARMENT FROM A VEHICLE POWER SOURCE
Your eis heated garment must be powered from the vehicle battery via the Fused Connection Lead as
installed above or the optional Cigarette Lighter/Accessory Plug. Ask your dealer for details or visit
www.keisapparel.co.uk.
To operate locate the 12v Supply Lead located in the pocket inside the garment. Simply connect or
disconnect this to and from the power source as required. An optional on/off switch is available.
Garme t Curre t
Draw
Outer Gloves
(Pair) 1.0A
IUnder Gloves
(Pair) 1.0A
Lo Power
Bodywarmer 1.5A
Hi Power
Bodywarmer 3.3A
Sleeved
Jacket 7A
Trousers 3.3A
Insoles (Pair) 1.3A
Fuses Colour
3A Purple
5A Tan
7.5A Brown
10A Red
15A Blue
NOTE: The potential
current drain when using
several garments can be
excessively high in some
situations. It is your
responsibility to ensure the
power source can provide
the current required in
such circumstances.
POWERING ACCESSORIES VIA YOUR KEIS HI-POWER BODYWARMER
Your eis Hi-Power Bodywarmer has dedicated power outputs for Gloves, Trousers and Insoles.
NOTE: These outputs remain live all the time the garment is connected to a power source and are not
affected by devices connected in the Controller Pocket. To control accessories powered by these sockets
separate or integral controllers will be required.