Keithley 3700 series User manual

Keithley Instruments, Inc.
28775 Aurora Road
Cleveland, Ohio 44139
1-888-KEITHLEY
www.keithley.com
PA-955 Rev. E / April 2010 1
Series 3700 Screw Terminal Assemblies
Installation Instructions
Introduction
This document contains handling and installation instructions for the Keithley Instruments Series 3700 System
Switch/Multimeter screw terminal assemblies.
NOTE Additional pin-out and connection information is included on the Product
Information CD-ROM that came with your instrument, or in the documentation
provided with your Series 3700 card.
If you have any questions after reviewing this information, please contact your local Keithley Instruments
representative or call Keithley Instruments corporate headquarters (toll-free inside the U.S. and Canada only) at
1-888-KEITHLEY (1-888-534-8453), or from outside the U.S. at [phone]. For worldwide contact
numbers, visit our website at www.keithley.com.
WARNING The following information is intended for qualified service
personnel. Do not make connections unless qualified to do so. To
prevent electric shock that could result in serious injury or death,
observe the following safety precautions:
•Before removing or installing a card in the mainframe, make
sure the mainframe is turned off and disconnected from line
power.
•Before making or breaking connections, make sure power is
removed from all external circuitry.
•Do not connect signals that may exceed the maximum
specifications of the model or external wiring. Complete
specifications for each card are included on the documentation
that came with the card. Please check the Keithley Instruments
website at 0www.keithley.com for the latest updates to the
specifications.
•All wiring must be rated for the maximum voltage in the
system. For example, if 300 V is applied to the backplane
connector, all card wiring must be rated for 300 V.

Series 3700 Screw Terminal Installation Instructions
2 PA-955 Rev. E / April 2010
Available screw terminal assemblies
Screw terminal assemblies available for use with Series 3700S cards include:
Model Link to figure
3720-ST Figure 1
3721-ST Figure 2
3723-ST Figure 1
3723-ST-1 Figure 3
3724-ST Figure 1
3730-ST Figure 4
3731-ST Figure 4
3732-ST-C Figure 5
3732-ST-R Figure 6
3740-ST Figure 7
3750-ST Figure 8
Screw terminal assembly circuit diagrams
The figures below depict a top-down view of the Series 3700 screw terminal assemblies.
NOTE Models 3723-ST-1, 3730-ST, 3740-ST, and 3750-ST screw terminal
assemblies have chassis ground connections ( ) for connecting a cable
shield.

Series 3700 Screw Terminal Installation Instructions
PA-955 Rev. E / April 2010 3
Figure 1: Models 3720-ST, 3723-ST, and 3724-ST screw terminal assemblies
Figure 2: Model 3721-ST screw terminal assembly

Series 3700 Screw Terminal Installation Instructions
4 PA-955 Rev. E / April 2010
Figure 3: Model 3723-ST-1 screw terminal assembly
Figure 4: Models 3730-ST and 3731-ST screw terminal assembly

Series 3700 Screw Terminal Installation Instructions
PA-955 Rev. E / April 2010 5
Figure 5: Model 3732-ST-C screw terminal assembly
NOTE The Model 3732-ST-C screw terminal assembly is labeled to show the correct
connections for the default quad 4x28 configuration. Insertable overlays are
provided with the screw terminal assembly that show the correct wiring for the
dual 4x56, single 4x112, dual 4x18 (2-pole), and single 4x56 (2-pole)
configurations.
For additional information about using the Model 3732 card and available
accessories, refer to the Model 3732 Quad 4x28 Reed Relay Matrix Card
Connection Information (part number PA-1021) document that came with your
Model 3732 card. You can also download the document from
www.keithley.com.

Series 3700 Screw Terminal Installation Instructions
6 PA-955 Rev. E / April 2010
Figure 6: Model 3732-ST-R screw terminal assembly
NOTE The Model 3732-ST-R screw terminal assembly is labeled to show the correct
connections for the dual 8x28 configuration. Insertable overlays are provided
with the screw terminal assembly that show the correct wiring for the single
16x28 and single 8x28 (2-pole) configurations.
For additional information about using the Model 3732 card and available
accessories, refer to the Model 3732 Quad 4x28 Reed Relay Matrix Card
Connection Information (part number PA-1021) document that came with your
Model 3732 card. You can also download the document from
www.keithley.com.

Series 3700 Screw Terminal Installation Instructions
PA-955 Rev. E / April 2010 7
Figure 7: Model 3740-ST screw terminal assembly
Figure 8: Model 3750-ST screw terminal assembly

Series 3700 Screw Terminal Installation Instructions
8 PA-955 Rev. E / April 2010
Screw terminal assembly installation and removal instructions
The following figures show how to connect a Series 3700 screw terminal assembly to the Series 3700 System
Switch / Multimeter and installed Series 3700 cards.
WARNING Before using a screw terminal assembly with an installed Series 3700 card,
verify that the card is properly installed in the Series 3700 mainframe, and the
mounting screws are tightly fastened. If the mounting screws are not properly
connected, an electrical shock hazard may be present.
NOTE For Series 3700 card installation instructions, refer to the Series 3700 Quick
Start Guide (part number 3700S-903-01), located on the Product Information
CD-ROM that came with your Series 3700 product.
To install a Series 3700 screw terminal assembly:
1. Remove the top cover of the screw terminal assembly (see Figure 9):
a. Loosen the slotted captive screws on the top cover.
b. Slide the top cover away from the retaining tab.
Figure 9: Removing the screw terminal assembly top cover

Series 3700 Screw Terminal Installation Instructions
PA-955 Rev. E / April 2010 9
2. Wire the screw terminal assembly circuit board:
CAUTION It is not necessary to remove a circuit board from its enclosure to wire the screw
terminal assembly. Avoid handling circuit board surfaces and terminal blocks,
because contaminants from hands may degrade the screw terminal assembly's
performance.
a. For screw terminal assemblies that include insertable overlays, select the correct overlay for the
configuration you are using and press it into place inside the screw terminal assembly.
b. As shown in Figure 10, route your wiring through the slots in the rear of the screw terminal assembly
and connect it to the proper wiring terminals (refer to the documentation supplied with your switch card
for proper connection information).
Figure 10: Routing and securing cables with ties
c. When all wires have been connected, use small cable ties to secure the wires and provide strain relief,
as shown in Figure 10. Pass the cable tie in and out of the small holes in the base of the screw
terminal assembly and around your wiring before pulling the cable tie tight.
3. When you have finished wiring the screw terminal assembly circuit board, reinstall the top cover on the
screw terminal assembly (see Figure 11):
a. Align the top cover with the circuit board.
b. Slide the cover forward and beneath the retaining tab.
c. Fasten the two slotted captive screws.

Series 3700 Screw Terminal Installation Instructions
10 PA-955 Rev. E / April 2010
Figure 11: Installing the screw terminal assembly top cover
4. After removing all power from the Series 3700 instrument, ensure that the mounting screws on the
installed Series 3700 card are secure (see Figure 12).
Figure 12: Check Series 3700 card mounting screws
5. Align the screw terminal assembly D-sub connectors with the connectors on the installed Series 3700
card (see Figure 13), and press to seat the D-sub connectors.
6. Turn the knob on the screw terminal assembly clockwise (see Figure 13) until it is firmly engaged (you
may need to use a slotted screwdriver to tighten the knob).
CAUTION Do not tighten the screws too much, because this will damage the card.