Kendal Lighting AC11152P-ORB/WN User manual

READ AND SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Model: AC11152P-ORB/WN

1
2. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items;
a. Blade set (5)
b. Hanger bracket
c. Canopy
d. Downrod
e. Coupling cover
f. Fan motor assembly
g. Set of blades bracket (5)
h. Switch housing
i. Package hardware
1) Mounting hardware :
wood screws (2), screws (2), lock washers (4),
washers (2), wire nuts (3), rubber gasket (2)
2) Blade attachment hardware:
screws (16), fiber washers (16)
3) Close-to-ceiling attachment hardware:
screws with lock washers (3)
4) Pull chain and fob
5) Balance Kit
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
ab
c
d
e
f
g
h
i
1. TOOLS AND MATERIALS
REQUIRED

1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualified licensed electrician.
3. CAUTION: Read all instructions and safety
information before installing your new fan.
Review accompanying assembly diagrams.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and lock
washers) provided with the outlet box for
mounting to the outlet box. Most outlet boxes
commonly used for the support of lighting
fixtures are not acceptable for fan support and
may need to be replaced, consult a qualified
electrician if in doubt.
5. The outlet box and support structure must be
securely mounted and capable of reliably
supporting a minimum of 50 pounds. Use only
CUL Listed outlet boxes marked "FOR FAN
SUPPORT".
6. The fan must be mounted with a minimum of 7
feet clearance from the trailing edge of the
blades to the floor.
7. Do not operate the reverse switch while the fan
blades are in motion. The fan must be turned
off and the blades stopped before reversing
the blades direction.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan
and other items, be cautious when working
around or cleaning the fan.
10. Do not use water or detergents when cleaning
the fan or fan blades. A dry dust cloth or lightly
dampened cloth will be suitable for most
cleaning.
11. After marking electrical connections, spliced
conductors should be turned upward and
pushed carefully up into outlet box. The wires
should be spread apart with the grounded
conductor and the equipment-grounding
conductor on one side of the outlet box.
12. Electrical diagrams are reference only. Light kit
that are not packed with the fan must be CUL
Listed and marked suitable for use with the
model fan you are installing. Switches must be
CUL General Use Switches. Refer to the
Instructions packaged with the light kits and
switches for proper assembly.
2
3. SAFETY RULES
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT
FAN TO OUTLET BOX MARKED
"ACCEPTABLE FOR FAN SUPPORT".
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.

3
4. MOUNTING OPTIONS
If there isn't an existing CUL listed mounting box,
then read the following instructions. Disconnect the
power by removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
(at least 50 lbs). Do not use plastic outlet boxes.
Figures 1,2 and 3 are examples of different ways to
mount the outlet box.
Note: You may need a longer downrod to maintain
proper blade clearance when installing on a steep,
sloped ceiling. (Fig. 3)
To hang your fan where there is an existing fixture
but no ceiling joist, you may need an installation
hanger bar as shown in Figure 4.
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Figure 1
Figure 3
Figure 4
Outlet box
Figure 2

Figure 7
Registration slot
4
5. HANGING THE FAN
Mounting screws
(supplied with
electrical box)
Hook
Ceiling
mounting
plate
CUL Listed
electrial
box
Figure 5
Figure 6
120V Wires
Washers
Downrod
Canopy
Set screws
Locking
pin
Hanger pin
Coupling cover
REMEMBER to turn off the power. Follow the steps
below to hang your fan properly:
NOTE: This ceiling fan is supplied with two types of
hanging assemblies; the standard ceiling
installation using the downrod with ball and socket
mounting and the "close-to-ceiling" installation.
The "close-to-ceiling" installation is recommended
in rooms with less than 8-feet ceilings or in areas
where additional space is desired from the floor to
the fan blades.
STANDARD CEILING INSTALLATION
Step 1. Pass the 120-volt supply wires through the
center hole in the ceiling hanger bracket as shown
in Fig. 5.
Step 2. Secure the hanger bracket to the ceiling
outlet box with the screws and washers provided
with your outlet box.
Step 3. Remove the hanger pin, lock pin and set
screws from the top of the motor assembly.
Step 4. Route wires exiting from the top of the fan
motor through the couping cover, canopy and then
through the ball / downrod. (Fig. 6)
Step 5. Align the holes at the bottom of the
downrod with the holes in the collar on top of the
motor housing. Carefully insert the hanger pin
through the holes in the collar and downrod. Be
careful not to jam the pin against the wiring inside
the downrod. Insert the locking pin through the hole
near the end of the hanger pin until it snaps into its
locked position, as noted in the circle inset of Fig. 6.
Step 6. Tighten two set screws on top of the fan
motor firmly. (Fig. 6)
Step 7. Place the downrod ball into the hanger
bracket socket. (Fig. 7)

5
Figure 8
Figure 9
Figure 10
CLOSE-TO-CEILING INSTALLATION
1. Remove the decorative canopy bottom cover
from the canopy by depressing the three studs
(Fig. 8)
2. Pass the 120-volt supply wires through the
center hole in the ceiling hanger bracket as
shown in Fig. 5.
3. Secure the hanger bracket to the ceiling outlet
box with the screws and washers provided with
your outlet box.
4. Place the ceiling canopy over the collar at the
top of the motor. Align the mounting holes with
the holes in the motor and fasten using the
screws and lock washers provided (Fig. 9).
5. Tighten the mounting screws securely. (Fig. 9)
WARNING: Failure to completely tighten the three
screws in step 5 could result in fan loosening and
possibly falling.
6. Hang the fan on the hook of the hanger bracket.
Be certain that the canopy is fully locked into
hook as shown in Fig. 10. This will allow you to
make the electrical connections.
Canopy bottom cover
Hook
Screw and lock washer
Canopy
Canopy
Collar

6
6. INSTALLATION OF
SAFETY SUPPORT
An additional safety support is provided to prevent
the fan from falling. Secure the safety cable to the
ceiling joist with screw and washer, as illustrated in
Figure 11.
7. MAKE THE ELECTRIC
CONNECTIONS
Remember to disconnect the power.
Follow the steps below to connect the fan to your
household wiring. Use the wire connecting nuts
supplied with your fan. Secure the connectors with
electrical tape. Make sure there are no loose
strands or connections.
Step 1 Connect the fan supply (black) wire and
light supply (blue) wire to the black household
supply wire as shown in Figure 12.
Step 2. Connect the neutral fan (white) wire to the
white neutral household wire.
Step 3 Connect the fan ground wire (green) to the
household ground wire.
Step 4 After connecting the wires, spread them
apart so that the green and white wires are on one
side of the outlet box and the black and the blue
wires are on the other side.
Step 5 Turn the connecting nuts upward and push
the wiring into the outlet box.
Figures 13 and 14 illustrate the wiring connections
for optional wall control (The wire color out of wall
control may vary, see wall control's installation
manual for correct wire connections.)
Hanger bracket Safety cable
Figure 11
Figure 12
Figure 13
BLK
WIRING
BOX
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
POWER LINES 120V
WH
BLUE
BLK
WH
FAN
LIGHT
BLK
BLUE WH
WH
LIGHT
SWITCH
GREEN GROUND
WH
BLUE
BLK
WH
GRN
WIRING
BOX
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
BLUE
BLK WH
WH
FAN
LIGHT
POWER LINES 120V
BLK
GREEN GROUND

7
WARNING: TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR OTHER PERSONAL
INJURY. MOUNT FAN ONLY ON AN OUTLET
BOX OR SUPPORTING SYSTEM MARKED
ACCEPTABLE FOR FAN SUPPORT.
8. FINISHING THE
INSTALLATION
STANDARD CEILING INSTALLATION
Slide canopy up to the ceiling as shown in Figure
15. Make sure you place the wires safely into the
outlet box. Secure the canopy to the hanger
bracket with the four screws with your fan.
CLOSE-TO-CEILING INSTALLATION
Remove the fan from the hook on the hanger
bracket. Secure the canopy to the hanger bracket
as shown in Figure 16 with four screws included
with your fan.
Figure 14
Figure 15
Figure 16
GROUND TO
MOUNTING
BRACKET
OR DOWNROD
POWER LINES 120V
GREEN
GROUND
WIRING
BOX
BLK
WH
WH
FAN
LIGHT
WH
WH
BLUE
BLK
LIGHT
FAN
Outlet box
Hanger
bracket
Canopy
Screws
Outlet box
Hanger
bracket
Canopy
Screws

8
Figure 17
Figure 18
9. ATTACHING THE FAN
BLADES
CAUTION: Remove 5 rubber packing mounts and
discard before installation.
Step 1 Attach the blade to the blade bracket using
the screws and fiber washers as shown in Figure
17. Start screw into bracket. Repeat for the two
remaining screws.
Step 2 Tighten each screw. Make sure the blade is
straight.
Step 3 Fasten blade assembly to motor using the
screws supplied. (Fig. 17)
10. INSTALLING THE
SWITCH HOUSING
NOTE: Before starting installation, disconnect
the power by turning off the circuit breaker or
removing the fuse at fuse box. Turning power
off using the fan switch is not sufficient to
prevent electric shock.
1. Remove the screws from the mounting plate
under the fan motor.
2. While holding the switch housing under
your fan, snap together the wire connection
plug. (Fig. 18)
3. Raise the switch housing to the mounting
plate until the holes in switch housing and
mounting plate line up. Reinsert screws to
secure in place. (Fig. 18)
Blade
Blades bracket
Screws
Fiber
washers
Screws
Screws
Switch
housing
Connection plug

9
Figure 19
Figure 20
11. OPERATING
INSTRUCTIONS
NOTE: Wait for fan to stop before changing the
setting of the slide switch.
Turn on the power and check the operation of your
fan.
1. 3-speed pull chain- it controls the fan speed as
follows: 1 pull- High, 2 pulls- Medium, 3 pulls-
Low, and 4 pulls- Off.
Speed settings for warm or cool weather depend
on factors such as the room size, ceiling height,
number of fans, and so on.
2. Light pull chain it controls the light in "ON" or
"OFF".
The slide switch controls directions: forward (switch
left ) or reverse (switch right ).
Warm weather - (Forward) A downward air flow
creates a cooling effect as shown in Figure 19.
This allows you to set your air conditioner on a
higher setting without affecting your comfort.
Cool weather - (Reverse) An upward airflow moves
warm air off the ceiling area as shown in Figure 20.
This allows you to set your heating unit on a lower
setting without affecting your comfort.

10
Problem
Fan will not start.
Fan sounds noisy.
Fan wobble.
Solution
1. Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections in the
switch housing. CAUTION: Make sure main power is off.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub is
tight.
3. Make sure wire nut connections are not rubbing against each other or the
interior wall of the switch housing. CAUTION: Make sure main power is off.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan
disappear during this time.
5. If using an optional light kit, make sure the screws securing the glassware
are tight. Check that light bulb is also secure.
6. Do not connect the fan with wall mounted variable speed control (s).
7. Make sure the upper canopy is a short distance from the ceiling. It should
not touch the ceiling.
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal.
Check this level by selecting a point on the ceiling above the tip of one of
the blades. Measure this distance. Rotate the fan until the next blade is
positioned for measurement. Repeat for each blade. The distance deviation
should be equal within 1/8".
3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by
side) blades can redistribute the weight and possibly result in smoother
operation.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT
BEND THE BLADE ARM WHILE INSTALLING, BALANCING THE BLADES,
OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS
BETWEEN ROTATING FAN BLADES.
12. TROUBLESHOOTING