Kendal Lighting Virtua User manual

(MODEL NUMBER:AC-22752)

1

1. Securely attach the hanger bracket to the outlet box
by washers and screws suppplied. Connect white
wire from ceiling to white wire from receiver with
wire nut. Connect black wire from ceiling to
black wire from receiver with wire nut. (see Fig.4)
2. Carefully lift the fan and seat the down rod ball
assembly on the hanger bracket. Be sure the
groove in the ball is lined up with tab on the
hanger bracket . Do not pinch wires between the
ball and down rod assembly and hanger bracket
(see Fig.5)
3. Install the safety cable into the building structure.
(see Fig.6)
Putting Your Fan Together
Hanging Your Ceiling Fan
1. Remove the hairpin clip & washer from the clevis
pin and remove clevis pin from down rod. (see
Fig.1)
2. Insert the down rod through the center opening in
the canopy,coupling cover and route the motor
leads through the hanger ball/downrod assembly.
Align the clevis pin holes in the downrod with the
holes in the motor coupling. The clevis pin must
pass through the holes in the motor coupling and
the downrod. Place the washer onto the clevis pin
and install the hairpin clip making sure to push
straight leg of the hairpin clip through the hole
near hanger ball to make sure the clevis pin is
properly installed(see Fig.2)
3. Reinstall the 2 set screws in the motor coupling and
securely tighten set screws against the down rod
assembly.
Attached each blade assembly to the blade bracket
using the blade screws and blade washers.Tighten
them securely.(see Fig.3)
Caution: To reduce the risk of personal injury.
Do not bend the blade when installing, balancing
or cleaning the fan. Do not insert foreign objects
between rotating fan blades.
DOWNROD
ASSEMBLY
WASHER
CLEVIS PIN
HAIR PIN CLIP
DOWNROD ASSEMBLY
CANOPY HOLE COVER
COUPLING COVER
WASHER
SCREW
FAN BODY
CLEVIS PIN
HAIR PIN CLIP
MOTOR COUPLING
CANOPY
SCREW
WASHER
BLADE
BLADE BRACKET
OUTLET BOX
HANGER BRACKET
FLAT WASHER
STAR WASHER
SPRING WASHER
SCREW
WHITE WIRE
BLACK
WIRE
WHITE WIRE
RECEIVER
BLACK
WIRE
HANGER BRACKET
DOWNROD
CEILING
SATETY CABLE
WASHER
WASHER
SCREW
DOWNROD
HANGER BRACKET

Wiring Your Ceiling Fan
Caution: To avoid possible electrical shock,
be sure electricity is turned off at the main
fuse box before wiring.
1. If you are not sure that the electrical box is
grounded,contact a licensed electrician for
advice.It must be grounded for safe operation.
2. Connect the red wire from receiver to the
red wire from fan with wire nut .Connect
the purple wire from receiver to the purple
wire from fan with wire nut.Connect the
blue wire from receiver to the blue wire
from fan with wire nut. Connect the grey
wire from receiver to the grey wire from
fan with wire nut. Connect the white wire
from receiver to the white wire from fan
with wire nut.Connect the green wire from
ceiling,and green wire from hanger bracket
with green wire from downrod ball with
wire nut.(see Fig.7)
3.Remove one of screws and loosen the other
screw from the hanger bracket. (see Fig.8)
4. Mount the canopy on the hanger bracket
and tighten the screws.(see Fig.9)
5. Place the canopy hole cover over the screws
and twist the cover to tighten. (see Fig.10)
GREEN WIRE
OUTLET BOX
RECEIVER
BLUE WIRE
WHITE WIRE
GREY WIRE
RED WIRE
PURPLE WIRE
FAN
HANGER
BRACKET
SCREW
HANGER
BRACKET
CANOPY
SCREW
SCREW
CANOPY
CANPOY HOLE
COVER
SCREW
LIGHT KIT ADAPTER
FAN

1. Remove 1 of 3 screws on light kit adapter,and
loosen the other 2 screws. (See Fig.11)
2.Gently pull the wire through light kit plate.Have
the key hole over the loosened the screws.Turn
the light kit plate until it get the end of narrow
end. Then, tighten the previously removed and
loosened screws.(see Fig.12 & 13)
3.Remove 3 screws on light kit plate.(see Fig.14)
4.Plug together light kit wires from fan to light kit
wires from LED light(see Fig.15)
5.Tighten the light kit by using the 3 screws
removed in step 3 (see Fig.16)
6. Attach the PC shade by locating tabs in light
kit with grooves on the light shade and twist
clockwise until tight (see Fig.17)
Installing The Light Kit
SCREW
SCREW
LIGHT KIT PLATE
LIGHT KIT PLATE
LIGHT KIT
ADAPTER
FAN
SCREW
LIGHT KIT
PLATE
LIGHT KIT PLATE
PIN
LED LIGHT
PLUG
LIGHT KIT PLATE
SCREW
TAB
LIGHT KIT PLATE
INDENTATION
PC SHADE

TNA18010305

REMOTE CONTROL SETTING AND OPERATION
UNIVERSAL MODE AND LEARNING MODE
There is a “Universal Mode” and “Learning Mode” with the remote control.
When selecting “Universal Mode”, simply place dip (code) switch at UPPER
position(COMMON CODE). Your fan remote control is ready to use.
Note: If using universal mode, your fan can be controlled with other remote
transmitters with the same setting.
To control the fan with specific remote transmitter, choose “ Learning Mode ”
by placing the dip (code) switch at LOWER position(L.CODE) and then select
function setting as below.
Learn function setting: Restore power source to your fan, press and hold
the “ LEARN ” button for at least 3 seconds. You must press the “LEARN ”
button within 60 seconds of restoring power to the fan.
Note: Power must be off for a minimum 10 seconds, then turn the power
back on for remote control learn function setting.
Note: If the fan is installed with light, light will blink 2 times. The remote
control setting process is complete and your fan is ready for use. For fans
without light, check operation using remote transmitter.
Note: To control multiple fans, ensure the settings are set at the same setting.
A fan can be controlled by 2 transmitters maximum.
TRANSMITTER OPERATION
Remove the battery cover from the remote control transmitter and install batteries,
Replace the cover.
Note : Use 2 1.5V/AAA batteries (included).
Note : If not using for long period of time, remove battery to prevent damage
to remote transmitter, and store the remote transmitter away from excess
heat or humidity.
ON
DIM
LEARN
L.CODE
COMMON
CODE
L.CODE
COMMON
CODE
ON
DIM
Universal Mode
Learning Mode
DIMMING / NON DIMMING SETTING
The “DIM” selection is the light dimmable selection , the light will cycle
from bright to dim to bright until button is released. The “ON” selection is the
light ON/OFF only (non dimming function).Light will maintain last setting if
turned off.
Note: The remote control is pre-set with dimming function at factory,
Note: Ensure electricity is turned off before installing the receiver (Refer
to the ceiling fan instructions)
Dimming/
Non dimming
LEARN
Learn
RECEIVER PROTECTIVE FUNCTIONS
Lock protection- The DC motor has a built-in safety feature against blade or motor obstruction during operation. should
something obstruct the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation
after about 60 seconds of interruption. Please remove obstacles and reset. To reset, turn the fan off with remote
transmitter and then turn the fan on. Or, you may turn the power off for 15 seconds. Then turn the power back on, and
then turn the fan on.
Over load protection (current limit)- The device limits the maximum current output from the receiver/drive when the fan
or light load is increased abnormally. The fan will shut off if over lamped.
TN15122801

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Remote Control Fan Speed And Light Functions.
Fan speed
1 = minimum speed 2 = low speed
3 = medium low speed 4 = medium speed
5 = medium high speed 6 = high speed
This button turns the fan off.
Forward/ Reverse button- This button controls the direction of the fan rotation
.
Press once to change direction of the fan rotation. Fan must be running to reverse.
Light button-Press this button to turn light on or off. To dim light ( Setting at “DIM”
position ), hold down the button, the light will cycle from bright to dim to bright until button
is released.
Note : This remote control has an auto resume function, the fan and light will maintain the
last setting if power is turned off.
NOTE:
1. When powering on after installation, the fan may start automatically due to factory preset settings.
2. If fan or light isn’t working, reset power ( turn the power off for at least 10 seconds and then turn the power back on
)
and redo the learn function setting.
3. If there are multiple fans in the same room, when setting, please make sure the power supply for the setting fan is
independant of the other fans.
4. When turning the fan on or operating the forward/reverse function, it is normal for the fan to rotate and run on both
directions, for approximately 1 minute and then stop.
TN15122801
Install Transmitter wall mount cradle with 2 screws provided.
WALL MOUNT CRADLE INSTALLATION
(Note: It can take a few seconds to change direction once button has been pushed.)