Kendal Lighting Lopro KENAC21352SN User manual

(MODEL NUMBER:AC-21352)

FIG.1FIG.2FIG.3FIG.4FIG.5FIG.6Putting Your Fan Together1. Securely attach the hanger bracket to the outlet box by washers and screws suppplied. Connect white wire from ceiling to white wire from receiver with wire nut. Connect black wire from ceiling to black wire from receiver with wire nut. (see Fig.5)2. Carefully lift the fan and seat the down rod ball assembly on the hanger bracket. Be sure the groove in the ball is lined up with tab on the hanger bracket . Do not pinch wires between the ball and down rod assembly and hanger bracket(see Fig.6)3. Install the safety cable into the building structure.(see Fig.7)Hanging Your Ceiling Fan1.Loosen the screw from the hanger ball and remove the pin, set screw and clevis pin from down rod. (see fig 1)2.Insert the down rod through the center opening in the canopy, coupling cover and route the motor leads through the downrod. (see fig 2)3. Align the clevis pin holes in the downrod with the holes in the shaft.The clevis pin must pass through the holes in the shaft and the downrod. Then tighten set screws and clevis pin against the down rod. (see fig 3)4. Tighten the pin and screw previously removed and loosened in step 1.(see fig.4)Remark: Insert safety cable(from fan) into downrod, slide cable clamp and washer(from parts bag) onto safety cable.FIG.7PINHANGER BALL SCREWSET SCREW DOWNRODCLEVIS PINHANGER BALLCANDPY HOLECOVERDOWNRODDOWNRODSET SCREW CLEVIS PINCENTER BANDPINHANGER BALLSCREWDOWNRODWHITE WIREBLACK WIREWHITE WIREBLACK WIRERECEIVEROUTLEX BOXHANGER BRACKETFLAT WASHERSTAR WASHERSPRING WASHERSCREWRECEIVERHANGER BRACKETDOWNRODCEILINGSAFETY CABLEWASHERWASHERSCREWHANGER BRACKETDOWNROD

1. If you are not sure that the electrical box is grounded,contact a licensed electrician for advice.It must be grounded for safe operation.2. Connect the red wire from receiver to the red wire from fan with wire nut . Connect the purple wire from receiver to the purple wire from fan with wire nut.Connect the grey wire from receiver to the grey wire from fan with wire nut.Connect the blue wire from receiver to the blue wire from fan with wire nut. Connect the white wire from receiver to the white wire from fan with wire nut. Connect the green wire from ceiling,and green wire from hanger bracket with green wire from downrod ball with wire nut. (see fig 8)3. Remove one of screws and loosen the other screw from the hanger bracket. (see Fig.9)4. Mount the canopy on the hanger bracket and tighten the screws to hold the canopy in place. (see Fig.10)5. Place the canopy hole cover over the 2 screws and twist the cover to tighten. (see Fig.11)1. Attach each blade assembly into the center band using the blade screws. Tighten them securely (see Fig.12)Caution: To reduce the risk of personalinjury. Do not bend the blade wheninstalling, balancing or cleaning the fan.Do not insert foreign objects betweenrotating fan blades.FIG.8FIG.9FIG.10FIG.11FIG.12Wiring Your Ceiling FanCaution: To avoid possible electrical shock,be sure electricity is turned off at the mainfuse box before wiring.OUTLET BOXRECEIVERPURPLE WIREGREY WIREBLUE WIREFANWHITE WIREHANGER BRACKETSCREWHANGER BRACKETCANOPYSCREWCANOPYSCREWCANOPY HOLECOVERCENTER BANDBLADESCREWRED WIREGREEN WIRE

1. Remove the 3 screws from the light kit adapter. (see fig 13)2. Remove the PC cover lens from LED light kit by removing the 3 screws. (see Fig.14)3. Lift up the light kit and pull the wire through the hole of light kit. Then, tighten the 3 screws previously removed in step 1 (see Fig.15)4. Connect the plug as drawing .(see Fig.16)5. Install the pc cover lens with the screws previously removed in Step 2.(see Fig.17)6. Twist on the shade to cover the LED light kit. (see Fig.18)7. If you do not need the light kit , skip steps 1 through 6 and just attach decorative cap instead of shade. (see Fig.19)
FIG.13FIG.14FIG.15FIG.16FIG.17FIG.18FIG.19Installing The Light KitLIGHT KIT ADAPTERSCREWLIGHT KITLIGHT KIT ADAPTERSCREWSCREWSCREWPC COVER LENSSCREWPLUGPINPC COVERLENSSCREWTABINDENTATIONPC GLASSTABINDENTATIONDECORATIVE CAP

TNA16041101

REMOTE CONTROL SETTING AND OPERATION
UNIVERSAL MODE AND LEARNING MODE
There is a “Universal Mode” and “Learning Mode” with the remote control.
When selecting “Universal Mode ”, simply place dip (code) switch at UPPER
position(COMMON CODE). Your fan remote control is ready to use.
Note: If using universal mode, your fan can be controlled with other remote
transmitters with the same setting.
To control the fan with specific remote transmitter, choose “ Learning Mode ”
by placing the dip (code) switch at LOWER position(L.CODE) and then select
function setting as below.
Learn function setting: Restore power source to your fan, press and hold
the “ LEARN ” button for at least 3 seconds. You must press the “LEARN ”
button within 60 seconds of restoring power to the fan.
Note: Power must be off for a minimum 10 seconds, then turn the power
back on for remote control learn function setting.
Note: If the fan is installed with light, light will blink 2 times. The remote
control setting process is complete and your fan is ready for use. For fans
without light, check operation using remote transmitter.
Note: To control multiple fans, ensure the settings are set at the same setting.
A fan can be controlled by 2 transmitters maximum.
TRANSMITTER OPERATION
Remove the battery cover from the remote control transmitter and install batteries,
Replace the cover.
Note : Use 2 1.5V/AAA batteries (included).
Note : If not using for long period of time, remove battery to prevent damage
to remote transmitter, and store the remote transmitter away from excess
heat or humidity.
ON
DIM
LEARN
L.CODE
COMMON
CODE
L.CODE
COMMON
CODE
ON
DIM
Universal Mode
Learning Mode
DIMMING / NON DIMMING SETTING
The “DIM” selection is the light dimmable selection , the light will cycle
from bright to dim to bright until button is released. The “ON” selection is the
light ON/OFF only (non dimming function). Light will maintain last setting if
turned off.
Note: The remote control is pre-set with dimming function at factory,
Note: Ensure electricity is turned off before installing the receiver (Refer
to the ceiling fan instructions)
Dimming/
Non dimming
LEARN
Learn
RECEIVER PROTECTIVE FUNCTIONS
Lock protection- The DC motor has a built-in safety feature against blade or motor obstruction during operation. should
something obstruct the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation
after about 60 seconds of interruption. Please remove obstacles and reset. To reset, turn the fan off with remote
transmitter and then turn the fan on. Or, you may turn the power off for 15 seconds. Then turn the power back on, and
then turn the fan on.
Over load protection (current limit)- The device limits the maximum current output from the receiver/drive when the fan
or light load is increased abnormally. The fan will shut off if over lamped.
TN15122801

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Remote Control Fan Speed And Light Functions.
Fan speed
1 = minimum speed 2 = low speed
3 = medium low speed 4 = medium speed
5 = medium high speed 6 = high speed
This button turns the fan off.
Forward/ Reverse button- This button controls the direction of the fan rotation
.
Press once to change direction of the fan rotation. Fan must be running to reverse.
Light button- Press this button to turn light on or off. To dim light ( Setting at “DIM”
position ), hold down the button, the light will cycle from bright to dim to bright until button
is released.
Note : This remote control has an auto resume function, the fan and light will maintain the
last setting if power is turned off.
NOTE:
1. When powering on after installation, the fan may start automatically due to factory preset settings.
2. If fan or light isn’t working, reset power ( turn the power off for at least 10 seconds and then turn the power back on
)
and redo the learn function setting.
3. If there are multiple fans in the same room, when setting, please make sure the power supply for the setting fan is
independant of the other fans.
4. When turning the fan on or operating the forward/reverse function, it is normal for the fan to rotate and run on both
directions, for approximately 1 minute and then stop.
TN15122801
Install Transmitter wall mount cradle with 2 screws provided.
WALL MOUNT CRADLE INSTALLATION
(Note: It can take a few seconds to change direction once button has been pushed.)