Kendal Lighting AC-21454 User manual

(MODEL NUMBER:AC-21454)

1. Remove 3 screws on mounting plate. (see
fig.1)
2. Install the mounting plate onto junction box
with the provided mounting hardware.(see
fig.2)
3. Hang the cable from the fan body up to the
hook on mounting plate.(see fig.3)
1. Install the mounting plate onto ceiling
with proivded washers and screws.Install
the safety cable onto the ceiling with the
wood screw provided.(see fig.4)
2. Connect the pin connector between motor
and re ceiver. Connect white wire from
ceiling to white wire from receiver with
wire nut. Connect black wire from ceiling
to black wire from receiver with wire nut.
Connect the green wire from ceiling fan
and green wire from mounting plate with
green wire f rom fa n with wire nu t. (see
fig.5)
3. Place receiver onto motor assembly. Flat
side up.(see fig.6)
FIG.1
FIG.2
FIG.3
FIG.4
FIG.5
FIG.6
MOUNTING PLATE
SCREW
OUTLEX BOX
MOUNTING PLATE
WASHER
WASHER
SCREW
MOUNTING PLATE
SAFETY CABLE
MOTOR
SCREW
WRENCH
SAFETY CABLE
BOTTOM HOUSING
CEILING
MOUNTING
PLATE WASHER
WASHER
SCREW
SAFETY
CABLE
MOUNTING PLATE
RECEIVER
MOTOR
MOTOR
RECEIVER

FIG.10
FIG.12
FIG.13
SCREW
BLADE ARM
BLADE
SCREW LIGHT KIT
ADAPTER
SCREW
LIGHT KIT
FIG.9
SCREW
BOTTOM HOUSING
4. Lift the fan body up and turn the motor
into the mounting plate.(see fig.7)
5. Tighten the 3 screws to fix the motor.using
allen screws and wrench provided.(see fig.8)
6. Move motor housing up over motor +
mounting plate and secure with the 3 screws.
(see fig.9)
1. Attach each blade assembly to the blade arm
using the blade screws. Tighten them
securely (see Fig.10)
Caution: To reduce the risk of personal
injury. Do not bend the blade when
installing, balancing or cleaning the fan.
Do not insert foreign objects between
rotating fan blades.
FIG.7
FIG.8
MOUNTING PLATE
MOTOR
RECEIVER
MOUNTING PLATE
WRENCH
BOTTOM HOUSING
SCREW
SCREW
WIRE
CLIP
When you want to install light kit, remove the
wire clip first.（see fig.11）
Warning: if no light kit added, keep the
wire clip and install the decorative cap
directly
FIG.11

1. Remove 1 of 3 screws on fan adapter and loosen
the other 2 screws.(see fig.12)
2. Attach the light kit adapter to fan adapter by
placing key slots over the 2 loosened screws, turn
the light kit adapter until it get the narrow end of
key slots and have the round hole align with the
round hole on fan adapter. (see fig.13) Tighten the
screws. (see fig.14)
3.Remove 1 of 3 screws on light kit adapter and
loosen the other 2 screws.(see fig.15)
4.Connect the plug between the fan wire with light
kit wire and lift the light kit plate upto light kit
adapter, have the key key slots over the two loosened
screws. Turn the light kit plate until it get the narrow
end of key slots. (see fig.16)Tighten screws. (see
fig.17)
5.Assemble the glass and glass holder.(see fig.18)
6.Turn the glass assembly to install onto light kit
plate. (see fig.19)
7. If you do not need the light kit, you can also install
the decorative cap directly onto the flywheel. Skip
fig.11 to fig.19. Align the 3 slots with 3 ribs, and lift
the decorative cap onto flywheel and tighten the 3
long screws. (see fig.20 and fig.21)
SCREW SCREW
SCREW
LIGHT KIT
ADAPTER
LIGHT KIT
ADAPTER
PIN PLUG
LIGHT KIT
SCREW LIGHT KIT
SCREW
GLASS
GLASS HOLDER
LIGHT KIT
GLASS
FLYWHEEL
DECORATIVE CAP
BOLT
CLIP
SCREW
DECORATIVE CAP
DECORATIVE
CAP
FIG.14
FIG.15
FIG.16
FIG.17
FIG.18
FIG.19
FIG.20
FIG.21

TNA15111003

REMOTE CONTROL SETTING AND OPERATION
UNIVERSAL MODE AND LEARNING MODE
There is a “Universal Mode” and “Learning Mode” with the remote control.
When selecting “Universal Mode”, simply place dip (code) switch at UPPER
position(COMMON CODE). Your fan remote control is ready to use.
Note: If using universal mode, your fan can be controlled with other remote
transmitters with the same setting.
To control the fan with specific remote transmitter, choose “ Learning Mode ”
by placing the dip (code) switch at LOWER position(L.CODE) and then select
function setting as below.
Learn function setting: Restore power source to your fan, press and hold
the “ LEARN ” button for at least 3 seconds. You must press the “LEARN ”
button within 60 seconds of restoring power to the fan.
Note: Power must be off for a minimum 10 seconds, then turn the power
back on for remote control learn function setting.
Note: If the fan is installed with light, light will blink 2 times. The remote
control setting process is complete and your fan is ready for use. For fans
without light, check operation using remote transmitter.
Note: To control multiple fans, ensure the settings are set at the same setting.
A fan can be controlled by 2 transmitters maximum.
TRANSMITTER OPERATION
Remove the battery cover from the remote control transmitter and install batteries,
Replace the cover.
Note : Use 2 1.5V/AAA batteries (included).
Note : If not using for long period of time, remove battery to prevent damage
to remote transmitter, and store the remote transmitter away from excess
heat or humidity.
ON
DIM
LEARN
L.CODE
COMMON
CODE
L.CODE
COMMON
CODE
ON
DIM
Universal Mode
Learning Mode
DIMMING / NON DIMMING SETTING
The “DIM” selection is the light dimmable selection , the light will cycle
from bright to dim to bright until button is released. The “ON” selection is the
light ON/OFF only (non dimming function). Light will maintain last setting if
turned off.
Note: The remote control is pre-set with dimming function at factory,
Note: Ensure electricity is turned off before installing the receiver (Refer
to the ceiling fan instructions)
Dimming/
Non dimming
LEARN
Learn
RECEIVER PROTECTIVE FUNCTIONS
Lock protection- The DC motor has a built-in safety feature against blade or motor obstruction during operation. should
something obstruct the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation
after about 60 seconds of interruption. Please remove obstacles and reset. To reset, turn the fan off with remote
transmitter and then turn the fan on. Or, you may turn the power off for 15 seconds. Then turn the power back on, and
then turn the fan on.
Over load protection (current limit)- The device limits the maximum current output from the receiver/drive when the fan
or light load is increased abnormally. The fan will shut off if over lamped.
TN15122801

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Remote Control Fan Speed And Light Functions.
Fan speed
1 = minimum speed 2 = low speed
3 = medium low speed 4 = medium speed
5 = medium high speed 6 = high speed
This button turns the fan off.
Forward/ Reverse button- This button controls the direction of the fan rotation
.
Press once to change direction of the fan rotation. Fan must be running to reverse.
Light button- Press this button to turn light on or off. To dim light ( Setting at “DIM”
position ), hold down the button, the light will cycle from bright to dim to bright until button
is released.
Note : This remote control has an auto resume function, the fan and light will maintain the
last setting if power is turned off.
NOTE:
1. When powering on after installation, the fan may start automatically due to factory preset settings.
2. If fan or light isn’t working, reset power ( turn the power off for at least 10 seconds and then turn the power back on
)
and redo the learn function setting.
3. If there are multiple fans in the same room, when setting, please make sure the power supply for the setting fan is
independant of the other fans.
4. When turning the fan on or operating the forward/reverse function, it is normal for the fan to rotate and run on both
directions, for approximately 1 minute and then stop.
TN15122801
Install Transmitter wall mount cradle with 2 screws provided.
WALL MOUNT CRADLE INSTALLATION
(Note: It can take a few seconds to change direction once button has been pushed.)