Kenmore 415.162120 User manual

AssemblyInstructions/UseandCare Manual
®
LiquidPropaneGasGrill
ModelNo.415.162120
ThisGrillIs For
OutdoorUseOnly
NO TOOLS
ASSEMBLY
•Read this manual before cooking on
grill. Failure to follow all
manufacturer's instructions could
result in fire or explosion which could
cause property damage, personal
injury or death.
•Combustion by-products produced
when using this product contain
chemicals known to the State of
California to cause cancer, birth
defects, or other reproductive harm.
•Parts
•Assembly
•Safety Rules
•Use and Care
•Troubleshooting
•Read and follow all Safety
Statements, Assembly Instructions
and Use & Care Directions before
attempting to assemble and cook.
•Some parts may contain sharp edges,
especially as noted in these
instructions. Wear protective gloves
if necessary.
Assembly Questions?
Call 1-800-4-MY-HOME _
Parts Ordering:
Call 1-800-366-PART (7278)
To Installer/Assembler: Leave
these instructions with
consumer.
To Consumer: Keep this
manual for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP tank not connected for use shall
not be stored in the vicinity of this or any
other appliance.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your
gas supplier or your fire department.
Call Grill Service Center For Help And Parts
If you have questions or need assistance during assembly,
please call 1-800-241-7548.You will be speaking to a
representative of the grill manufacturer and not a Sears
employee. Toorder new parts call Searsat 1-800-4-MY-HOME_.
ProductRecord
IMPORTANT:Filloutthe productrecordinformationbelow.
Model Number
Serial Number Seeratinglabelongrill forserialnumber.
Date Purchased
CAUTION
For residenUal use only. Do not use for commercial
cooking.
Safety Symbols
The symbols and boxes shown below explainwhat each heading
means. Read andfollow all of the messages found throughout
the manual.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Be alert to thepossibilityof serious bodily injury
ifthe instructions are notfollowed. Be sure to read and
carefully follow all of the messages.
CAUTION: Indicates a potentially hazardous situation which,
if notavoided, may result in minor or moderate injury.
Installation Safety Precautions
•Use grill only with LP (propane) gas and the regulator/valve
assembly supplied.
Grill installation must conform with local codes, or in their
absence with National Fuel Gas Code, NFPA 541 ANSI
Z223.1. Handling and storage of LP cylinders must conform to
LP Gas Code NFPNANS158. Grill is notfor use in or on
recreational vehicles and/or boats.
All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with localcodes, or
National Electrical Code, ANSI INFPA 70. Keep any
electrical cords and/or fuel supply hosesaway from any hot
surfaces.
•This grill is safety certified for use in the United Statesonly. Do
not modifyfor use in any other location.Modification will result
in a safety hazard.
CARBON MONOXIDE HAZARD
Burning charcoal releases carbon monoxide which has no
odor and can cause serious injury or death. Never burn
charcoal inside homes, vehicles or tents.
2 • 463741404

ForYour Safety...................................... 2
Grill Service Center................................... 2
Product Record information ............................ 2
Safety Symbots...................................... 2
instaliation Safety Precautions .......................... 2
Kenmore Gritl Warranty ............................... 3
Parts List........................................... 4
Parts Diagram....................................... 5
Assembly ........................................ 6-15
Use and Care ................................... 16-25
Cooking Chart............................... 24
Troubleshooting ............................. 25
RepairProtectionAgreements
Congratulations on making a smartpurchase. Your new
Kenmore'_product is designed and manufactured for years of
dependable operation. But like ali products, it may require repair
from time to time. That's when having a Repair Protection
Agreement can save you money and aggravation.
Purchase a Repair Protection Agreement now and protect
yourself from unexpected hassle and expense.
Here'swhat's included in theAgreement:
,,¢ Expert service byour 12,000 professional repair speciaIists
._ Unlimited service and no chargefor parts and labor on all
covered repairs
Product replacement if your covered product can't be fixed
._ Discount of 10% from reguiarprice of service and service-
related paris not covered by the agreement; also, 10% off
regular price of preventive maintenance check
_f Fast help by phone - phone support from a Sears
technician on products requiring in-home repair, ptus
convenient repair scheduIing
Once you purchase theAgreement, a simple phone cali is all that
it takes for you to schedule service. You can call anytime day or
night, or schedule a service appointment online.
Sears hasover t2,000 professional repair specialists, who have
access to over4.5 million quality parts and accessories. That's
the kind of professionalismyou can count on to heip prolong the
tile of your new purchase for yearsto come. Purchase your
Repair ProtectionAgreement today!
Some limitations and exclusions apply.
For pricesand additional information call t-800-827-6655,
Sears Installation Service
For Searsprofessional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
USA. cail 1-800-4-MY-HOME_
KENMORE GRILL WARRANTY
Full t-Year Warranty on Grili
For one year from the date of purchase Sears will repair or
replace, at our option, anygrill part (except for paintfinish)
that isdefective in material or workmanship.
Limited Warranty on Selected Grill Parts
From one year after thedate of purchase for the designated
time periods IistedbeIow,Sears wilI replacethe following grill
parts ifthey are defective in material or workmanship. You
will be chargedfor labor.
• Lifetime of Grill:Aluminum Topand Bottom Castings
(exceptfor paint finish)
• 2 years: BurnerAssembty
WARRANTY SERVICE
Warrantyservice is available by contacting Sears at
1-800-4-MY-HOME_.
WARRANTY RESTRICTIONS
This warranty isvoid ifgrill is used for commercial or rental
purposes.
This warranty applies ontywhen the grill is used in the United
States.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept.817WA,
Hoffman Estates, IL60179
463741404• 3

I 2 LOgA_mbly ....................... 4-503239
2 I Baoe.............................. 4-502429
3 11 #10-24_'2_Caoiogo Bait............... 4.080084
4I2 #10-24PaoticTeeKnob............... 4.080091
5 I Midohelf ........................... 4151034
6 2 Wheel,a._sembly..................... 4.310002
74I" H_;h Pn ......................... _)80082 STD524001
8 2 LOgE×_nder ....................... 4.I54577
9 I Gdll Batb,_m......................... 4.555535
I0 I BamerAssembly .................... 4.505074
I1 I CAle_,fforBox ....................... 4.500278
I2 I Electrode .......................... 6155119
I3 I #10-15xl!Z Self-TapS_w ............ 4L_SOO59STD511555
I4 I OontrolPanel....................... 4525143
I5 I VelvdHosdRogulob,_rAo_m bly ........ 4524195
I 5 2 ValveCli_ .......................... 4.I51043
I7 4. #10_1/2_,T_20,Self-TapS_w ......... 4L_80043
I5 I Igniter ............................. 5155113
I5 I IgniterWiro......................... 4.153198
20 I SidebornerIgn_,_rWire................ 5155109
21 2 I/4-20xl -1/# CorriogeBait ............ 4L_50515STD532512
22 2 I/4_25 Wng Net ..................... 4L_50221STD541825
23 2 #10-24x%I/4"CarriageBait............ 4LJ80074
24 I TankWire .......................... 4.151018
25 I ',/-bar.............................. 4.500325
25 2 P_ntrolKnob........................ 4.I54559
27 I Front Panel......................... 4-502456
25 I Front PanelShelf .................... 4-I54515
29 4. Puoh-Footener...................... 44_80579
30 I PanelWire ......................... 4.I51040
31 4. End Cop........................... 4LJ80055
32 I SideShelf.......................... 4.I54572
33 5 #10-12xl-7t5_WingSc_'w............. 4L_SOOg5
IToolHolder......................... 4.I545T5
35 I SidebornerBody..................... 4525185
35 I SidebornerFrame.................... 4.501705
37 4. #10-24WingNot..................... 4L_50053STD541610
35 I Sideborner......................... 5055028
39 I SidebornerKnob..................... 4.I54471
4.0 I SidebornerGrate.................... 4.I55576
4.1 I Gdll Lid............................ 4.550595
4.2 2 I/4_1-1/5" HingePn .................. 4-I55513
4-3 I Handle ............................ 4-I54473
44 2 #10-24xI" MachineS_w ............. 4L_80502STD511010
4.5 I Tem_mraturoGougeBa_el............. 4.I57159
4.5 I Tem_mraturoGougewithWing Nut ...... 4.I57171
4.7 I LogoPlate ......................... 4.I56051
4.5 2 3/15"PalNut........................ 4.I53098
4.9 I Swin_woy ......................... 4.152124
50 I C_okJogGrate ...................... 4.152739
51 I GreasoClip......................... 5155607
4. 463741404

41.
•47
43 45
_" 44
40
\
/
/
/
_4
13
12 42 21 32
31
14
7
//
2_
17
..... 15
463741404,5

CartAssemblyStep1
_iliPositionbaseonedgewithtankholetoleftside.
Liinsertlegsintobaseandattach withcarnagebolts
andplasticwingnuts.Usetopholesonleftside.
DONOTFULLYTIGHTEN.
insertmidshelfwire intoholeson insidesoflegs,
longwires towardleftside.Fullytightencarnage
boltsandplasticwingnuts.
4
Qty.8
3
Qty.8
LegAssembly_
Longmidshelfwire
toleftside.
6. 463741404

CartAssemblyStep2
,_ insertwheel/hubcapassembliesinto
bottomholesonleftlegs,
Securebeneathbasewithhitchpins.
Seeinsetbelow.
Pushlegextendersintorightlegs.
;;; i¸¸ _
Wheel!HubcapAssembly
7
....LegExtender
h_chpininaxlebolt,
463741404,7

GrillBottom/ControlPanelAssembly AndTankWire
,_ Carefullyplacegrillbottom/controlpanel
assemblyontocart,soas notto scratchpaint
on legs.Makesurecontrolpanelbracketfitsover
supportbaroneachside.
insertcarriageboltsthroughgrillb_tom and
centerholein supportbar.Threadmetalwingnuts
ontoboltsbutdo notfullytighten.
L] insertcarriageboltsthroughcontrolpanelbracket
and frontholesinsupportbar.Securewithplastic
wingnuts.
EliFullytighteninstal wingnuts. _21
insertendsoftankwireinto pin408061
slotsoneachsideoftank
holein grillbase.Leantank
wiretowardmidshelf.
22
Qty.2 4
Qty.2
2t
pin4080615......... 21 23
pin4080815 p/n4080074
Qty.2 Qty.2
GrillBottom/Control....... ;:_
PanelAssembly ;_
23
pin4080074.....
.... pin 4080074
SupportBar
TankWire\
NOTE: Wheels are to left side.
8. 463741404

V-bar and ControlKnobAssembly
_RestV-baron barsupportsat each
endofgrillbottom.
Presscontrolknobsontovalvestems.
_.V-barSupport
Knobs
463741404,9

FrontPanel,ShelfAndPanelWireAssembly
_Snapshelfintofront panel.Makesurethatshelfrests
ontop offrontpanelshelfsupporttab.
i Hookouterwireson panelwireintoholesinpanel,
rotatepanelwire down,and insertremainingwires
intoholesinfrontofshelf.
SlidetopedgeoffrontpanelUNDERcontrolpanel.
Li Securepanelto legswithpush-fasteners. 29
Qty.4
Snapfront panelshelf
_into front panel.
paneiTopof front panel
fits UNDER contro
,_ Attachfront
/panel tolegs.
Attechpanelwireto
frontpaneland shelf.
t0. 463741404

EndCap,SideShelf,AndToolHolderAssembly
_Jinsertendcapsintoendsoflegtubes.
Positionsideshelfontorightlegsasshown
belowandsecurewithfourwingscrews.
i Positiontoolholderontoleftfrontlegand
securewithtwo carriageboltsandplastic
wingnuts.Usethetwoouterholes.Do not
usethemiddlehole.
4
Qty.2
3
Oty.2
33
Qty.4
SideShelf
EndCap
/
,1
3
Holder
33
463741404• 11

Sideburner
Frame
SideburnerAssembly
L] Placesideburnerbodyontolegs.Secureatfrontwithonewingscrewthroughleg,toolholder,andinto body.
iinserttabonsideburnerframeintoholeinbody.Atrearleg,insertcarriageboltthroughframe,body,andmiddleleghole.
Securewith metalwingnut.
insertsideburnertubeintolargeframe hole.Insertburner'sthreadedstudintosmallframehole.Attachmetalwingnutto
stud,butdo notfullytighten.
insertsideburnervalveintoburnertubeandsnapvalvecup intobody.Notepropertube-to-valveengagementinfigure A.
Onceproperengagementismade,fullytightenmetalwingnutbeneathburner.
_] Attachsideburnerignitorwire (longwire behindcontrolpanel)toelectrodebeneathsideburner.SeefigureB.
Presssideburnerknobfirmlyontosideburnervalveand placesideburnergrateontobody.
!iiInserttab
intohole.
Sideburner
Body
......
37
Qty.2
3
Qty.1
33
Qty.1
Sideburner
Grete
\
Sideburner_
IgnitarWire
Sideburns
ValveCup
t2. 463741404

GrillLid,Handle,TemperatureGauge _
and LogoPlateAssembly
[_ Attachgrilllidtogrillbottomwith
hingepinsand hitchpins.
A_eh handleto lidwithmachinescrews
andmetalwingnuts.
i Removewingnutfromtemperature
gauge,insertgaugeintobezel,then 44
intoholeingrilllid.Securew_hwingnut. pin4060302
Qty.2
37
Qty.2
Qty.2 12
pin4t56513
Qty.2
44-
pin 4080302
Handle
44
pin4080302.......
WingNut
GrillLid
42
/pin 4156513
42 sJ
pin 4156513
463741404• 13

SwingAwayAndCookingGrateAssembly
_insertSwingAwaypivotwiresintoholes
in side_f grilllid.
insertSwingAwaylegwiresintotopholes
in sideofgrillb_tom,
i Placecookinggrateontogrsterestsin
grillbottom,
NOTE:
BackofSwingAwayshouldbepointingupward.
....PivotWire
_s SwingAway
\\
CookingGrste
t4. 463741404

TankWire,LPTankAndGreaseClipAssembly
._ PlaceLPtankintoholein basewith
tankvalvefacingtowardfrontofgrill.
TosecureLPtank, pulltank wireover
theside_f thetank,towardthetank collar.
SeeUseandCaresectionfor conneetion
ofregulatortoLPtank.
i Hanggreaseclipbeneathgrillbottom.
Seeinsetbelow.To colleetgrease,hang
anemptysoupcan(notincluded)from
greaseclip.
,£ LPGASTANKISSOLD
SEPARATELY.Filland leek-
checktank beforeattaching
to grillandregulator.SeeUse
and Caresectionfor instructions.
F
i, Tankcollaropeningmustface tofrontofcartonce
i tank isattached.
, Failuretoinstalltank correctlymay allowgashoseto
bedamagedinoperation,resultingintherisk_f fire.
LPTank
(Sold
Separately)
TankWire
iFailureto installcanin clipwillcausehot
' greaseto dripfrombottomof grillwithrisk_f
ifire orpropertydamage.
463741404• 15

•Never fill the cylinder beyond 80% full. An overfilled
spare LPtank is hazardous due to possiblegas
released from the safety reliefvalve.
•The safety relief valve on the LP tank could activate
releasing gas and cause an intense fire with risk of
property damage, serious injury or death.
• NEVER store aspare LPtank under or near grill or in
enclosed areas.
•If you see, smell or hear escaping gas, immediately get
away from the LPtank/grill and call your fire
department.
, All spare LPtanks must have safety caps installed on
the LPtank outlet.
LP Tank Removal, Transport And Storage
•Turn OFF ali control knobsand LP tank valve. Turncoupting
nut counterolockwise by handonly - do not usetools to
disconnect. Lift LP tank wire upward off of LP tank cotlar,then
iift LP tank up and off of suppori bracket, install safety cap onto
LP tankvalve. Always use cap and strap supplied with valve.
Failureto usesafety cap as directed may result in serious
personal injury and/or property damage.
LPTankValve
LP Tank
• The LP tank used with your grill must meet the following
requirements:
• Use LP tanks only with these required measurements: t2"
(30.5cm) (diameter) x t8" (45.7 cm) (tail)with 20 ib. (9 kg.)
capacity maximum.
•LPtanks must be constructed and marked inaccordance with
specifications for LP tank of the U.S. Department of
Transportation (DOT). See LP tank collar for marking.
•LPtank valve must have:
• Type 1 outlet compatiblewith
regulator or grill.
• Safety relief valve.
• ULlisted Overfill Protection
Device (OPD). This OPD safety OPDHandWheel
feature is identified by a unique triangular hand wheel. Use
only LPtanks equipped with this type ofvalve.
•LPtank must be arranged for vapor withdrawal and include
cellarto protect LP tank vaIve.
LP (Liquefied PetroleumGas)
•LPgas isnontoxic, odorless and colorlesswhen produced. For
Your Safety, LPgas has been given an odor (similar to rotten
cabbage) sothat it can be smelied.
•LPgas ishighty flammable and may igniteunexpectediy when
mixed with air.
LPTank Filling
• Use only licensed and experienced dealers.
•LPdealer must purge tank before filling.
• Deniershoutd NEVER fili LPtank more than 80% of LP tank
volume. VoIume of propane in tank wilivary bytemperature.
• A frosty regulator indicates gas overfiil, immediateIy close LP
tank valve and call local LP gas dealer for assistance.
• Do not release liquid propane (LP)gas intothe atmosphere.
This is a hazardous practice.
• To remove gas from LP tank, contact an LP dealer or caIIa
iocalfire department for assistance. Check the teIephone
directory under "Gas Companies_for nearest ceriified LP
dealers.
• A disconnected LPtank in storage or being transported must
have a safety cap installed (as shown). Do notstore an LP tank
in enciosed spaces such as a carport, garage, porch, covered
patio or other building. Never leave an LP tank inside a vehicle
which may become overheated by the sun.
• Do notstore an LP tank in an area wherechildren piny.
t6.4_1_4

LPTank Exchange
• Many retailers that selI grilIs offer you the option of replacing
your empty LP tank through an exchange service. Use only
those reputable exchange companies that inspect, precisionfiII,
test and cer[ifytheircylinders. Exchange your tsnkonly for
an OPDsafety feature-equipped tank as described in the
"LP Tank"section ofthis manual.
• Always keep new and exchanged LPtanks in upright position
during use, transit or storage.
•Leak test new and exchanged LPtanks BEFORE
connecting to grill.
Connecting Regulator To The LP Tank
1. LPtank must be properlysecured onto grill. (Refer to
assembly section.)
2. Turn alIcontrol knobs to the OFF position.
3. Turn LP tank OFF by turning OPD hand wheel clockwise to a
full stop.
4. Removethe protective cap from LP tank valve.Always use
cap and strap supplied with valve.
LPTank LeakTest
Foryour safety
•Leaktest must be repeated each time LPtank is exchanged or
refilled.
• Do notsmoke during leak test.
• Do not usean open flame to check for gas leaks.
•Grili must be leak tested outdoors in a weli-ventitated area,
away from ignitionsources such as gas fired or eIectrical
appliances. During leak test, keep grill away from open flames
or sparks.
• Use a clean paintbrush and a 50/50 mildsoap and water
solution. Brushsoapy solution onto areas indicated byarrows
in figure beiow.
If 'growing" bubbles appear do not useor move the LP tank.
Contact an LP gas supplier or your fire department!
OPDHandWheel
threadonoutside
Do not usea POL transport plug
(plastic part with external threads)l
It will defeat the safety feature of
the valve,
ADo not use household cleaning agents. Damage togas
train components can resutt.
5. Holdregulator and insert nipple into LP
tank vaive. Hand-tighten the coupling
nut, holding regulator in a straight tine
with LP tank valve so as notto cross-
thread the connection.
Nipple hastobecentered
into theLPtankvalve.
v
463741404• 17

Holdcouplingnutand regulator
asshownfor properconnection
to LPtankvalve.
6. Turn the coupling nut clockwise and tighten to a full stop. The
regulator will seal on the back-check feature in the LP tank
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only - do not use tools.
NOTE:
if you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
•Do not insert any foreign objects intothe valve outlet. You
may damage the valve and cause a leak. Leaking propane
may result in explosion, fire, severe personal injury,or
death.
• Never attempt to attach thisgrill to the self-contained LP gas
system of a camper trailer or motor home.
Do not use grill until leak-tested.
If a leak is detected at any time, STOP and callthe fire
department.
If you cannot stopa gas leak, immediately close LP tank
valve and call LPgas supplier or your fire department!
LeakTesting Valves, Hose and Regulator
1. Turn all grill control knobs to OFF.
.
3.
Be sure regulator istightly connected to LPtank.
Completely open LPtank valve by turning OPD hand wheei
counterclockwise. If you hear a rushing sound, turn gas off
immediately.There isa major leak at the connection. Correct
before proceeding.
.Brush soapy solution onto areas where bubbtesare shown in
picture beIow: ANeverremovethreaded
orificeatend ofvalve.
Valve
5. If "growing" bubbles appear,there isa leak. Close LPtank
valve immediatelyand retighten connections. If leaks cannot
be stopped do not try to repair. Call Sears for reptacament
paris at 1-800-4-MY-HOME_.
6. Always close LPtank valve after performing leaktest by
turning hand wheei clockwise.
tit *4637414_4

i
iFor Safe Use Of Your Grill And To Avoid Serious
iInjury:
i ' Do not tet children operate or play near grill
i, Keepgrill area clearand free from materials that bum.
i, Do not btock holes inbottom or back of grill
i ' Check burnerflames regularly.
• Use grill only in weII-ventilated space. NEVER use in
enclosed space such as carport, garage, porch, covered
patio, or under an overheadstructure of any kind.
• Do not use charcoal or ceramic briquets in agas grill.
(Unlessbriquets are supplied withyour grill.)
: • Use grill at least 3ft. from any wall or surface, Maintain
10 ft. clearance to objects thatcan catchfire or sources of
ignitionsuch as pilot tightson waterheaters, iive electrical
appliances, etc.
Apartment Dwellers:
Checkwith management to team the requirements and fire
codes for usingan LP gas grill in your apartment complex. If
allowed, use outside on the ground floor with a three (3) foot
clearance from wallsor rails. Do not useon or under
balconies.
NEVER attempt to light burner with lid closed, A buildup
of non-ignited gas inside a closed grill is hazardous.
Never operate grill with LP tank out of correct position
specified in assembly instructions.
Always close LPtank valve and remove coupling nut
before moving LP tank from specified operation
position.
Safety Tips
,&
,&
Before opening LPtank valve, checkthe coupling nutfor
tightness.
When grill is notin use, turn off all control knobs and LP tank
valve.
iI. Never move grill whilein operation or still hot.
iI. Use long-handled barbecue utensils and oven mitts to avoid
bums and splatters.
iI. Maximum load for shelves is 10 Ibs.
i
i
i
i
Asoup can must be attached to grease clip and emptied
after each use. Do not removesoup can until grill has
completely cooled.
if you notice grease or other hot material dripping from grill
onto valve, hose or regulator,turn off gas supply at once.
Determine the cause, correct it, then cleanand inspect valve,
hose and regulator before continuing. Perform a leak test.
The regulator may make a humming or whistling noise during
operation. This will not affect safety or useof grill.
if you havea grill problemsee the "Troubleshooting Section".
If the regulator frosts, turn off grill and LP tank valve
immediately.This indicates a problem with the tank and it
should not be used on any product. Return to supplier]
46,3741484• 19

i
=• Putting out grease fires by closing the lid is not
possible. Grills arewell ventilated for safety reasons.
Do not use water on a grease fire. Personal injury may
result, ifa grease fire develops, turn knobs and LP tank
off,
Do not leave grill unattended while preheating or
burning offfood residue on high. if grill has not been
regularly cleaned, agrease fire can occurthat may
damage the product.
Match-Lighting
ADo not lean over grillwhile lighting.
1. Open lid. Turnon gas at LPtank.
2. Placelit match into match-Iighting hoIefrom beneath grill
bottom (as shown below).
3. Pushin and turn fight knob to O (ignite position). Be sure
burner lights and stays tit.
4. Light left burner by pushingIeft knob in and turning to •
(ignite position).
After Lighting: Turn knobs to HI for warm-up.
Ignitor Lighting
ADo not lean over grill while lighting.
1. Open lid. Turn on gas at LP tank.
2. Turn left knob to O (ignite position).
3. Pushignitor button rapidly (up to 5 times) to light. Be sure
burner lights and stays tit.
4. if burner does not light, turn knobs to _, wait 5 minutes,
try again.
5. Once left burner islit, turn right knob to _ to light right
burner.
6. tf ignitordoes notwork, wait5 minutes, then follow match
lighting instructions.
After Lighting:Turn knobs to HI position for warm-up. Do not
warm up grill with knobs on _ (ignite position). Knobs and
handle willbecome uncomfortably hot if left in _ (ignite
position).
If burner does not light, turn knobsto_, wait 5
minutes, and try again. If the burner does not ignite with
the valve open, gas will continue to flow out ofthe burner
and could accidentally ignite with risk of injury.
holeis
beneathgrillbottom.
Ignitor Lighting The Sideburner
1. Turn on gas at LPtank.
2. Pushin and turn sideburner knobto HI.
3. Pressand hold ignitor button to light. Be sure burner lights and
stays lit.
4. if burner does not light, turn sideburner knob to OFF, wait 5
minutes, try again.
Match Lighting
i. Turn on gas at LP tank.
2. Holda lit match to any port on the sidebumer. Push in and
turn the sidebumer knobto HI. Be sure burner Iightsand stays
tit.
20* 463741404