Kenmore 363.63672 User manual

Installation
Instructions Speedcook
vens
363.63672,363.63673,363.63674,363.63679,
363.63692,363.63693,363.63694,363.63699
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT -Savethese
instructions for local inspector's use.
• IMPORTANT - Obse_eall
governing codes and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keepthese
instructions for future reference.
• Skill level -Insta!ladon of dais appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not
covered under the Warranty.
LA SECCION EN ESPAI_iOL
EMPIEZA EN LA PAGINA 25. READ CAREFULLY, KEEP THESE INSTRUCTIONS.

Installation Instructions
CONTENTS
General information
Important Safety Instructions ................ 3
Electrical Requirements ..................... 3
Hood Exhaust .......................... 4, 5
Damage---Shipment/Installation .............. 6
Parts Included ............................ 6
Tools You W'dl Need ....................... 7
Mounting Space o7
Step-by-step installation guide
Placement of Mounting Plate .............. 8-10
Removing the Mounting Plate . : ....... 8
Finding the Wall Studs ............... 8
Determining Wall Plate Location ....... 9
Aligning the Wall Plate .............. 10
Installation Types ..................... . 11-22
[] Recirculating ................... 12-14
Attach Mounting Plate to Wall ..... 12
Preparation of Top Cabinet ....... 13
Mount the Oven ............ 13, 14
Installing the Charcoal Filter ...... 14
[] Outside Back Exhaust ............ 15-18
Preparing Rear Wall for
Outside Back Exhaust ........... I5
Attach Mounting Plate to Wall..15, 16
Preparation of Top Cabinet ....... 16
Adapting Blower for Outside
Back Exhaust ............... 16, 17
Mount the Oven ............... 18
[] Outside Top Exhaust ............. 19-22
Attach Mounting Plate to Wall ..... 19
PrepaFation of'Fop Cabinet ....... 20
Adapting Blower for
Top Exhaust ................ 20, 21
Assemble and Install Adapter ..... 21
Mount the Oven ............ 21, 22
Adjust the Exhaust Adapter ....... 22
Connecting Ductwork ........... 22
Before You Use Your Oven .................. 23
Secei6n en _ol ..................... 25--47
2

Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This product requires a thre_prong grounded oudet.
The installer must pecfonn a gTound continuity check on
the power outlet box before beginning the installation to
instu'e that the outlet box is properly grounded, ff not
properly grounded, or if the outlet box does not meet
electrical requirements noted (under ELECIa_CAL
REQUIREMENTS), a qualified electrician should be
employed to correct any deficiencies.
ICAUTION:
For personal safety, remove
house fuse or open circuit
breaker before beginning
installation to avoid severe
or fatal shock injury.
CAU1]ON: Ferpo on themou g
surface must be capable of supporting the cabinet load, in-
adch'fion to the added weight of this 63-85 pound product,
plus additional oven loads of up to 50 potmds or atotal
weight of 113-135 potmds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangeme_ats such as an
island or a peninsula. It must be mounted to BOTH
a top cabinet AND a walL
NOTE: For easier installation madpersonal safety, it is
recommended that two people install this product.
IMPORTANT--_ READ CAREFULLY. FOR
PERSONAL SAFETY, THIS APPIJANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATALSHOCK.
The power cord of this
appliance is equipped with
a _-ee-pro_g _o_mding)
l_ug which mates with
astandard three-prong
(groundhlg) wall x_eptade
to minimize the possibility
of dec_wicshock hazard
from this appliance.
You should have the wall receptacle and circuit checked
by aqualified elec_clan to make sure the receptacle is
properly grounded.
Where astandard two_reng wall receptade is
encountered, it is very important to have it replaced
with a properly grounded three-prong wall receptacle,
installed by a qualified electrician.
DO NOT, LrNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL
REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 15 amps and
1.70 kilowatts. This product must be connected to
a supply circuit of the proper voltage and frequency.
Ware size must conform to the requirements of the
National Electrical Code or the prevailing local code for
this kilowatt rating. The power supply cord and plug
should be brought to a separate 15 to 20 ampere branch
circuit single grounded outlet. The outlet box should be
located in the cabinet above the oven. The outlet box and
supply circuit should be installed by a qualified electrician
and conform to the National Electrical Code or the
prevailing local code.
3

Installation Instructions
HOOD EXHAUST
NOT_ Read these next two pages only if you plan to vent your exhaust to the outside.
If you plan to reclrculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart desclibes an example of one possible ductwork installation.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
RoofCap 24 Ft. x (1) 24 Ft.
12Ft.StraightDuct 12 Ft. x (1) 12Ft.
(6"Round)
Rectangular-to-Round 5 Ft. x (1) 5 Ft.
TransitionAdapter*
Equivalentlengthsofductpiecesarebasedon actualtests and
reflectrequirementsfor goodventingperformancewith anyventhood. Total Length = 41 Ft.
*IMPORTANT: ff a rectangular-to-round transition adapter is used, the bottom comers of the damper will have
to be cut to fit, using the fin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an exmnple of one possible duc ,twork instanadon.
DUCT PIECES EQUIVALENT NUMBER EQUIVALENT
LENGTH* x USED -- LENGTH
40 Ft. x (1) 40 Ft.
Wall Cap
3Ft.StraightDuct 3 Ft. x (1) = 3 Ft.
(3¼"x 10" Rectangular)
(_ 30°Elbow 10Ft. x (2} 20 Ft.
Equivalentlengthsof ductpiecesare basedon actualteatsand
reflectrequirementsforgoodventingperformancewith anyventhood. Total Length = 63 Ft.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be
prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhausL
4

Installation Instructions
NOTE: If you need to install ducts, note that the total duct
length of 3¼" x 10" rectangular or 6" diameter round duct
should not exceed 140 equivalent feet.
Outside ventilation requires a HOOD EXHAUST DUCT.
Read the following carefiflly.
NOTE: It is important that venting be installed ttsing
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocldng the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with
a standard 3¼" x 10" rectangular ducL
ff a round duct is required, a rectangular-to-round
transition adapter must be used. Do not use less than
a6"diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length of
".5¼"x 10" rectangular or 6" diameter round duct should not
exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent to
asection of straight duct which is longer than their actual
physical size. When calculating the total duct length, add the
equivalent lengths of all tlansidons and adapters plus the
length of all straight duct sections.
The chart below shows you how to calculate total equivalent
ductwork length using the approximate feet of equivalent
length of some typical ducts.
;DUCT PIECES
G
g
RectangulaFto-Round
TransitionAdapter*
Wall Cap
90° Elbow
45° Elbow
90° Elbow
45° Elbow
EQUIVALENT NUMBER
LENGTH x USED
RoofCap
StraightDuct6" Roundor
3_A"x10" Rectangular
5R.
40Ft.
lOFt.
5R.
25 Ft.
5R.
24Ft.
1R.
x ( )
x ( )
x()
x ( )
x ( }
x ( )
x ( )
x( )
EQUIVALENT
LENGTH
Ft.
Ft.
F_.
Ft.
Ft,
Ft,
Ft.
Total Ductwork = Ft.
*IMPORTANT: Ifa rectangularao-round transition adapter is used,
the bottom comers of the damper will have to he cut to fit, using
the tin snips, in order to allow free movement of the damper.
Equivalent lengths of duct pieces are based on actual tests and
reflect _luirements for good venting perfoimance with any
vent hood.
5

Installation Instructions
DAMAGE SHIPMENT/
INSTALLATION
•If the unit is damaged in shipment, retuna the unit to the
store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the
customer), repair or replacement must be made by
arrangement between customer and installer.
PARTS INCLUDED
HARDWARE PACKET
PART QUANTITY
WoodScrews 2
_' 1¼0x2"1
, ToggleBolts(and 4
_ wing nuts)(¼"x 3")
Self-aligningMachine 3
Screws(¼"-28x3¼")
NylonGrommet 2
(formetalcabinets)
Metal Screws 1 black
(_,_"x ½") 2 bronze
PowerCordStrap 1
(plastic)
You will find the installation hardware contained in a
)acket with the unitCheck to make sure you have all
these parts.
NOTE: Some extra parts are included.
PARTS INCLUDED
ADDITIONAL PARTS
PART QUANTITY
1
TOp CABINJ_i"TEIdPLIffI_
I_Sl"ALLAT'_
J
i
TopCabinet
Template
RearWall
Template
Installation
Instructions
Separately 2
Packed
Grease
Filters
Exhaust 1
Adapter
Damper 1
Charcoal 1
Filter
6

Installation Instructions
TOOLS YOU WILL NEED
#1and#2 Phillipsscrewdriver Pencil
]in snips(forcutting
damper,if required)
G]oves
Safetygoggles
Scissors
(tocuttemplate,if necessary)
Saw(saber,holeorkeyhole)
Rulerortapemeasure
eightedge
Electricdrill with 3Ag'._6".
Vz"and_" drill bits
Studfinder or Hammer(optional)
Level
Carpentersquare
(optional)
Fillerblocksor scrap
woodpieces,if needed
fortopcabinetspacing
(usedonrecessedbottom
cabinetinstallationsonly)
Ductandmaskingtape
MOUNTING SPACE
66"ormore
fromthe floor
tothetopof
theoven
Bottomedgeof
cabinetneedsto
be30"ormore
the cooking
surface
NOTES:
•The space between the cabinets must be 30" wide
and free of obstructions.
•If the space between the cabinets is greater than
30;'a Filler Panel Kit may be used to fill in the
gap between the oven and the cabinets. Your
Use & Care Guide contains the kit number for
your model.
• This oven is for installation over ranges up to
36" wide.
• If you are going to vent your oven to the outside,
see Hood Exhaust Section for exhaust duct
preparation.
•When installing the oven beneath smooth, flat
cabinets, be careful to follow the inswuctions on
the top cabinet template for power cord clearance.
7

Installation Instructions
PLACEMENT OF THE MOUNTING PLATE
I-_ REMOVING THE OVEN FROM
THE CARTON/REMOVING THE
MOUNTING PLATE
[] Remove the box containing the installation
instructions, filters, exhaust adapter, damper
and the small hardware bag. Do not remove
the Styrofoam protecting the front of the oven.
[] Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton over
onto the top side. The oven should be resting in
the Styrofoam.
[] Pull the carton up and off the oven.
[_The mounting plate is attached to the back of the
oven. Remove the two screws holding it to the oven.
The plate will be used as the rear wall template and
for mounting the oven to the wall.
i
[_Set the oven upright. Remove and properly discard
plastic bags and Styrofoam.
[] Open the oven door and remove the styrofoam
pack from inside the oven. Remove the tape
covering the turntable hub.
[] FINDING THE WALL STUDS
ii wail i i
Center_i if!
[] Find the studs, using one of the following
methods:
A. Stud finder - a magaaetic device which
locates nails.
OR
B. Use a hammer to tap lighdy across the
mounting surface to find a solid sound.
This will indicate a stud location.
[] After locating the stud(s), find the center by
probing the wall with a small nail to find file
edges of the stud. Then place a mark halfway
between the edges. The center of any adjacent
studs should be 16" or 24" from this mark.
]Draw a line down the center of the studs.
THE OVEN MUST BE CONNECTED TO AT LEAST
ONE WALL STUD.
8

Installation Instructions
[-_ DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position - beneath flat bottom
cabinet Plate position - beneath framed recessed
cabinet bottom
MountingPlateTabs
the CabinetBottom
L
At least30", upto36"
MountingPlateTabs
TouchingtheBack
Frame
L
II 30"toCooktop
t
Plate position - beneath recessed bottom
cabinet with front overhang
MountingPlatewith
TabsBelowCabinet
Bottomthe Same
Distanceasthe Front
gDepth
L
I II 30"toC9oktop
f
Your cabinets may have decorative uam that interferes
with the oven installation. Remove the decorative trim
to install the oven properly and to make it level.
THE OVEN MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no
back or side frame, install the mounting plate down
the same distance as the front overhang depth. This
will keep the oven level.
[] Measure the inside depth of the front overhang.
[] Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside
depth of the front overhang.
[] For this type ofinstallauon with front overhang only,
align the mounting tabs with this horizontal line, not
touching the cabinet bottom as described in Step D,
9

Installation Instructions
ALIGNING THE WALL PLATE
HoleC
DrawaVertical
LineonWall
•,,e--frorn Centerof
TopCabinet
o o o
0 0 0 0 0 0 0 .b 0 0 0 0 O0 0 0 0 0
0 0 0 O O OIO O O O O 0 0
I
CAUTION: Wear gloves
to avoid cutting fingers on
sharp edges.
_f I
AreaE HoleD
[] Draw a vertical line on the wall at the center of the
30" wide space.
[_Use the mounting plate as the template for the rear
wall. Place the mounting plate on the wall, making
sure that the tabs are touching the bottom of the
cab'met or the level line drawn in Step C for cab'mets
with front overhang. Line up the notch and center line
on the mounting plate to the center line on the wall.
[] While holding the mounting plate with one hand,
draw circles on the wall at holes A, B, C and D (see
illustration above/actual plate marked with arrows).
Four holes must be used for mounting.
[]
NOTE: Holes C and D are inside area E, ff neither
C nor D is in a stud, find astud somewhere in area E
and draw a fifth circle to line up with the stud. It is
important to use at least one wood sca'ewmounted
firmly in a stud to support the weight of the oven.
Set the mounting plat e aside.
Drill holes on the circles, ff there is a stud, drill a_i6"
hole for wood screws. For holes that don't line up with
a stud, drill a _" hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
10