Kennmex K875 User manual

K875
User Manual
2006 November V1.1

Safety
IMPORTANT SAFETY INSTRUCTIONS
•Read these instructions carefully. Keep these instructions for future reference.
•Follow all warnings and instructions marked on the product.
•Do not use this product near water.
•Do not place this product on an unstable cart, stand, or table. The product may fall, causing
serious damage to the product.
•Slots and openings in the cabinet and the back or bottom are provided for ventilation; to
ensure reliable operation of the product and to protect it from overheating, these openings
must not be blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register, or in a built-in installation unless proper ventilation
is provided.
•This product should be operated from the type of power indicated on the marking label. If
you are not sure of the type of power available, consult your dealer or local power company.
•Do not allow anything to rest on the power cord. Do not locate this product where persons
will walk on the cord.
•Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
•The socket outlet should be installed near the equipment and should be easily accessible.
PSE Mark
This device complies with the PSE rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
Caution on Lithium Batteries
Danger will explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.
2

Table of Contents
Safety....................................................................................................................................... 2
1. Accessories..................................................................................................................... 4
2. Components.................................................................................................................... 4
2.1. Front View...................................................................................................................... 4
2.2. Rear View...................................................................................................................... 5
2.3. Button Cover View .......................................................................................................... 5
2.4. I/O Function.................................................................................................................... 6
3. Specification.................................................................................................................... 6
4. Installing External Devices............................................................................................... 8
4.1. Wall Mount Kit ................................................................................................................ 8
4.2. MSR............................................................................................................................... 10
5. Jumper Setting ................................................................................................................ 11
5.1. Main Board Jumper Setting.............................................................................................. 11
6. Driver Installation............................................................................................................. 13
6.1. Driver List....................................................................................................................... 13
6.2. USB 2.0 Driver Installation............................................................................................... 14
6.3. VGADriver Installation .................................................................................................... 17
6.4. Resistive Touch Driver Installation.................................................................................... 19
6.5. SAW Touch Driver Installation.......................................................................................... 23
6.6. Audio Driver Installation................................................................................................... 25
6.7. LAN Driver Installation..................................................................................................... 27
6.8. Intel (R) PROSet Driver Installation................................................................................... 28
7. BIOS Updating Procedure................................................................................................ 29
8. Default BIOS Setting........................................................................................................ 31
3

1. Accessories
a. Power Cord (1) b. RJ45-DB9 Converter Cable (4)
c. Driver CD (1) d. Power Brick (1)
2. Components
2.1. Front View
Touch Screen MSR
4
LED Lens

2.2. Rear View
Cable CoverButton Cover
Wall Mount
HDD Cover
2.3. Button Cover View
Brightness -
Brightness +
Power Button
Vo l u m e +
Vo l u m e -
5

2.4. I/O Function
Cash Drawer
Line-In LINE-Out
COM (4) USB (2)
USB (2) LPTLAN
DC Jack
3. Specification
System K875
Mainboard B78
CPU Support Celeron M1.3GHz; Pentium M1.8GHz;Intel
Chipset Intel 852GM and ICH4 FSB 400Mhz
System Memory B2 x DDR SO-DIMM sockets, up to 2G
Graphic Memory Shared system memory 8~64MB
BIOS Phoenix Award BIOS
LCD Touch Panel
LCD Size 15” TFT LCD
Brightness 350 cd/㎡
Maximal Resolution 1024 x 768
Touch Screen Type Resistive type, SAW type optional
Storage
HDD 2.5” Slim HDD bay
Flash Memory ther one option between HDD and CFOptional C.F. slot (ei
card)
Expansion
Mini-PCI Socket 1 x mini-PCI slot
Wireless LAN
WLAN module Optional mini-PCI wireless LAN module support up to IEEE
802.11 a/b/g
Antenna Main liary& Auxi
External I/O Ports
6

USB 4 ports (V2.0)
Serial / COM RJ-45 connectors (COM1 standard RS-232;4 x COM ports
COM2 RS232/422/485 selectable by jumper; COM3 &
COM4 pin 9 with 5V or 12V power by jumper)
Parallel 1 x D-sub 25-pin connector
LAN (10/100) 1 x RJ45
Cash Drawer 1 x RJ-11 (12V or 24V)
DC Jack 1 x DC Jack Latch type
Audio Jack 1 x Line-out, 1 x Line-in
Speaker
Speaker Integrated 2 x 2W speaker
Internal Interface
USB 2
COM 2
2nd VGA -pin (2 x 5) header for CRT10
Control/Indicator
Power Button 1
Indicator LED 1 x power LED
IrDA 1
Motion Sensor 1
Volume Control Button & DownUp
Brightness Control Button Up & Down
Power
Power Adapter External DC 19V, 90W
Peripherals
MSR Side mount ISO 3-tracks or JIS I&II module (Optional)
Scanner Laser scanner (Optional)
Web CAM odule (Optional)1.3M Pixel web camera m
Environment
EMC & Safety FCC, Class A, CE, LVD
Operating Temperature )0℃~ 40℃(32℉~ 104℉
Storage -20℃~ 60℃(-4℉~ 140℉)
Operating Humidity 5% - 95% RH non condensing
Storage Humidity 5% - 95% RH non condensing
7

Dust & Water Resistance NEMA 3 / IP55 (Front Bezel)
Dimensions (W x D x H) 386 x 330 x 65 mm / 15.2” x 13” x 2.6”
Weight 5.1kg / 11lbs
Mounting 75 mm x 75 mm & 100 mm x 100mm Standard VESA
mounting holes
OS Support WinXP Pro, Xpe, WEPOS, Windows NT 4.0 / 2000
‧This specification is subject to change without prior notice.
4. Installing External Devices
4.1. Wall Mount Kit
bracket on the rear bezel. Tighten the screws (4).1. Put the wall mount kit
Screws (2)
Screws (2)
. Tighten the screws (4) of the wall mount kit holder on the wall.2
8

3. Hang the system on the wall mount kit holder.
4. Tighten the screw (2).
Screw (1)
Screw (1)
9

4.2. MSR
e screws (3).1. Remove th
Screws (3)
. Slide the MSR cover out and disconnect the cable (1).2
Cable (1)
10