Kennmex EZPPC-70B-5B-C1G User manual

Service Manual
EZPPC-70B-5B-C1G
EZPPC-70B-5B-C15G
EZPOS-70B-5B-C1G
EZPOS-70B-5B-C15G

Copyrights i
Copyrights
©2009 All rights reserved. The information in this
document is subject to change without prior notice in
order to improve reliability, design and function and does
not represent a commitment on the part of the
manufacturer.
This document contains proprietary information
protected by copyright. All rights are reserved. No
part of this manual may be reproduced by any
mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
All trademarks are property of their respective
owners
Liability Disclaimer
In no event will the manufacturer be liable for direct,
indirect, special, incidental, or consequential
damages arising out of the use or inability to use the
product or documentation, even if advised of the
possibility of such damages.
The information in this document is subject to
change without notice

Contents
ii
Contents
Copyrights.................................................................................................i
Liability Disclaimer ...................................................................................i
Contents....................................................................................................ii
1. Before You Start ...................................................................................1
2. Opening the Device..............................................................................2
3. Connect Battery Pack..........................................................................4
4. RAM Replacement................................................................................6
5. Battery Replacement ...........................................................................7
6. LED indicator Replacement ................................................................8
7. Speaker Assembly Replacement........................................................9
8. HDD Replacement..............................................................................11
9. LCD Inverter Replacement................................................................13
9.1. Disconnect Inverter Cable......................................................................... 13
9.2. Remove the LCD Inverter .......................................................................... 14
10. Touch Panel Control Board Replacement......................................16
10.1. Disconnect Touch Panel Control Board Cable...................................... 16
10.2. Remove the Touch Panel Control Board................................................ 17
11. Power Switch Replacement.............................................................18
12. COM Cable Replacement.................................................................19
13. Mainboard Replacement..................................................................20
14. I/O Panel Replacement ....................................................................21
15. LCD Panel Replacement..................................................................23
16. BIOS setup........................................................................................25
16.1. System Time and System Date Adjustment........................................... 26
16.2. Serial ports Configuration....................................................................... 26
16.3. Boot Device Configuration...................................................................... 27
16.4. Save Configuration Changes and Exit ................................................... 27

1.
1. Before You Start
1. Please unplug the power cable before you start to work.
2. Please read and follow the instructions in this document carefully. Failure to
follow these instructions could damage your device and void the warranty.
1.1. Tools Suggested
All procedures in this document require the following tools:
#0 Phillips screwdriver #1 Phillips screwdriver
(magnetized suggested) (magnetized suggested)
1.5 mm hexagon socket spanner
(magnetized suggested)
Chapter 1 1

Chapter 2
2
2.
2. Opening the Device
1. Un-tighten two screws on the back panel anticlockwise.
2. Open the back panel.

3. The layout of the internal.
Chapter 2 3

Chapter 3
4
3.
3. Connect Battery Pack
Before power-on the device, please connect the battery to the mainboard:
1. Un-tighten two screws on the back panel anticlockwise.
2. Open the back panel.

3. For the location of the battery pack and the 10-1 pin male power connector,
please refer the picture shown below.
4. Plug the power cable to the 9-pin power connector in the correct orient.
5. Close the back panel and tighten two screws on the back panel.
Chapter 3 5

Chapter 4
6
4.
4. RAM Replacement
1. Open the tow ejectors on the slot by pushing them, and remove the RAM
from the slot.
4. Remove the old RAM and install a new one.
5. Align and insert the new RAM in the slot and push both ends of the RAM
down until the ejectors snap into place.

5.
5. Battery Replacement
1. Unplug the connector of the battery from the mainboard.
2. Loosen the two screws by #1 Phillips screwdriver as shown below and remove
the battery..
3. Install a new battery in the reverse procedure
Note: The battery cable must be connected in the correct orient.
Chapter 5 7