KENTMASTER TURBO-III-A DEHIDER User manual

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
TURBO-III-A DEHIDER
INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK
IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR
SERVICING THIS TOOL.
DEHIDER
TOOL DATA
MODEL: TURBO-III-A DEHIDER
ASSEMBLY NO: 6303000
TYPE: AIR OPERATED
NET WEIGHT: 2 LBS 12 OZ (1.26 KG)
INLET AIR PRESSURE: 90 P.S.I. (6 BARS)

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
OPERATING AND SAFETY INSTRUCTIONS
DO NOT OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTOOD THE SAFETY
INSTRUCTIONS AND OPERATING MANUALS.
DO NOT OPERATE THIS TOOL UNTIL YOU HAVE RECEIVED TRAINING IN THE HANDLING,
OPERATION AND USE OF THIS TOOL.
STOP USING A MALFUNCTIONING OR DEFECTIVE TOOL IMMEDIATELY. REPORT ANY
PROBLEMS OR DEFECTS TO YOUR SUPERVISOR FOR REMOVAL OF THE TOOL FROM
SERVICE.
DO NOT ATTEMPT TO REPAIR THE TOOL YOURSELF.
DO NOT ALLOW UNAUTHORIZED PERSONS TO USE TOOL.
REMOVE AND DISCONNECT POWER FROM THE TOOL WHEN TOOL IS LEFT UNATTENDED OR
IS NOT IN USE.
NEVER TIE DOWN, BYPASS, ALTER OR MODIFY THE ACTIVATING SWITCHES OR TRIGGERS OF
THIS TOOL.
NEVER MAKE ALTERATIONS OR MODIFICATIONS TO THIS TOOL.
BE CONSTANTLY AWARE AND ALERT FOR UNSAFE CONDITIONS AND REPORT THEM
IMMEDIATELY TO YOUR SUPERVISOR.
NEVER PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE CUTTING PATH OF THE
TOOL.
NEVER ALLOW ANYONE ELSE TO PLACE THEIR HANDS OR ANY PART OF THEIR BODY IN THE
CUTTING PATH OF THE TOOL.
DO NOT ACTIVATE CONTROL SWITCHES OR TRIGGERS OF THIS TOOL UNLESS YOU INTEND
TO TEST OR OPERATE THIS TOOL.
DO NOT USE THIS TOOL FOR ANY PURPOSE OTHER THAN IT’S INTENDED PURPOSE.
WHEN OPERATING THIS TOOL WEAR THE PROTECTIVE GEAR AND SAFETY EQUIPMENT
SUPPLIED TO YOU.
THE NOISE EMISSION (SOUND PRESSURE LEVEL) AT THE WORKSTATION MAY EXCEED 85 dB
(A). EAR AND SOUND PROTECTION GEAR IS REQUIRED.
= Hazards or unsafe practices which could result in severe personal injury,
death or substantial property damage.
= Hazards or unsafe practices which could result in minor personal injury,
product or property damage.
= Important installation, operation or maintenance information.
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!WARNING
!CAUTION
!WARNING
!CAUTION
!NOTICE

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
OPERATING INSTRUCTIONS
ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.
1. HOLD TOOL FIRMLY IN HAND WITH TRIGGER LEVER IN POSITION TO BE ACTIVATED BY FINGERS.
2. SQUEEZE TRIGGER TO ACTIVATED TOOL, RELEASE TRIGGER TO DEACTIVATE TOOL.
3. POSITION TOOL AND PERFORM CUTTING OPERATION.
4. DO NOT LAY TOOL DOWN WHEN TOOL IS NOT BEING USED. PLACE TOOL IN BRACKET (PART NO. 630100). BRACKET
SHOULD BE MOUNTED IN A CONVENIENT LOCATION NEAR OPERATOR.
5. TOOL REQUIRES 40 S.C.F.M. OF AIR @ 90 P.S.I. AIR PRESSURE.
MAINTENANCE
ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE
AND SERVICE TO THIS TOOL.
1. FILL LUBRICATOR WITH KENTMASTER AIR MIST OIL (PART NO. 7903050). SET DRIP RATE ACCORDING TO
INSTRUCTIONS SUPPLIED.
2. TOOL REQUIRES GREASING AFTER EVERY 3 TO 4 HOURS OF OPERATION. GREASE THREE (3) LOCATIONS USING
KENTMASTER GREASE GUN (PART NO. 450147) AND GREASE (PART NO. 790307).
3. FLUSH AIR MOTOR AT END OF EACH DAY’S USE BY SQUIRTING A FEW SQUIRTS OF KENTMASTER AIR OIL MIST (PART
NO. 790305) DIRECTLY INTO THE AIR INLET PORT. RUN TOOL A FEW SECONDS TO COAT AND PROTECT THE AIR
MOTOR AND INTERNAL PARTS OF TOOL.
BLADE REMOVAL AND CLEANING
ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR
REMOVING BLADE FROM TOOL.
ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADE FROM TOOL.
1. REMOVE COVER SCREW (ITEM NO. 1, FIG. NO. 1).
2. REMOVE PARTS (ITEM NOS. 2-7, FIG. NO. 1).
3. CLEAN ALL PARTS REMOVED WITH SOAP AND WATER.
4. SHARPEN BLADES WHEN NECESSARY AND LUBRICATE ALL PARTS.
5. REASSEMBLE ALL PARTS IN REVERSE ORDER.
Figure 1 BLADE REMOVAL
!WARNING
!WARNING
!WARNING
!WARNING

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
SERVICE
1. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN PREVENTIVE MAINTENANCE PROGRAM.
2. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.
3. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS AND CUSTOMER SERVICE INFORMATION.
4. SAFETY DATA FOR LOCTITE CORPORATION PRODUCTS "LOCQUIC - PRIMER N" AND "LOCTITE - 272"
EYE IRRITANT, MAY IRRITATE SENSITIVE SKIN.CONTAINS METHACRYLATE
ESTER. IN CASE OF EYE CONTACT, FLUSH WITH WATER FOR FIFTEEN (15)
MINUTES; GET MEDICAL ATTENTION. WASH AFTER SKIN CONTACT. IN CASE OF
SKIN IRRITATION, DISCONTINUE CONTACT WITH PRODUCT. TO AVOID SKIN
CONTACT, USE THE APPLICATOR NOZZLE PROVIDED. OTHER APPLICATORS ARE
AVAILABLE FROM LOCTITE CORPORATION.
KEEP MATERIAL AWAY FROM CHILDREN.
!CAUTION

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
PARTS BOOK
MODEL TURBO-III-A DEHIDER
Figure 2 6303000: MODEL TURBO-III-A

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
LOCTITE CORP. PRODUCTS “LOCQUIC – PRIMER N” AND ADHESIVE “LOCTITE 242” MUST BE APPLIED TO ITEMS
14, 21, 28, 29 FIG.2, PRIOR TO ASSEMBLY.
FOR “PRIMER – N”:
A. CLEAN PARTS
B. SPRAY THREADS ON SCREWS AND MATING PARTS WITH “PRIMER – N”
C. ALLOW PRIMER TO DRY 3-5 MINUTES
FOR “LOCTITE 242”:
A. CLEAN AND DRY PARTS
B. APPLY 242 TO THREADS ON SCREWS AND MATING PARTS
C. ASSEMBLE AND LET STAND FOR 30 MINUTES
6303000: DEHIDER TURBO-III-A
ITEM PART # DESCRIPTION QTY
6300370 BLADE SET (110mm)(4.33") -includes two blades - STANDARD 1
1 6300390 BLADE SET (100mm)(3.98") -includes two blades - OPTIONAL 1
6302810 ASSEMBLY, ECCENTRIC SHAFT, 0.062" OFFSET - STANDARD 1
2 6303170 ASSEMBLY, ECCENTRIC SHAFT, 0.042" OFFSET - OPTIONAL 1
3 5001310 RETAINING RING 1
4 6300560 WASHER 1
5 6300580 BLADE SPACER 1
6 6300740 AIR SUPLY RING 1
7 6300840 MUFFLER 1
8 6302360 SPRING LOAD 1
9 6302430 LEVER 1
10 6302440 LABEL - KENTMASTER 1
11 6302450 NAME PLATE - TURBO III 1
12 6302610 AIR MOTOR ASSEMBLY 1
13 6302630 VALVE ASSEMBLY 1
14 6302740 HOUSING, FRAME 1
15 6302770 FLANGE COVER 1
16 6302780 FLANGE, FRAME 1
17 6302820 LOCK RING, VALVE 1
18 6302830 COVER 1
19 6302880 SCREW, COVER LOCK 1
20 6302910 INSERT 1
21 6302920 COVER, DRIVE SIDE (W/GREASE FITTING) 1
22 7034070 MALE PLUG 1
23 7680270 O-RING 1
24 8506590 WASHER 2
25 8640030 DRIVE SCREW 6
26 8653140 PIN 1
27 9208140 SCREW 2
28 9234020 SCREW 8
29 9238040 SCREW 3
Figure 3 BOM FOR MODEL TURBO-III-A

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
ECCENTRIC SHAFT ASSEMBLY
DISASSEMBLY AND ASSEMBLY:
REMOVE MOTOR AND PININ GEAR ASSEMBLY (ITEM 12, FIG 2.) PRIOR TO REMOVING SHAFT ASSEMBLY
(ITEM 2, FIG. 2). REMOVE VALVE ASSEMBLY (ITEM 13, FIG. 2) AND RETAINING RING (ITEM 3, FIG. 2).
MOTOR AND PINION ASSEMBLY WILL SLIDE OUT. REASSEMBLE IN REVERSE ORDER.
STEP 1:
PLACE SHAFT ASSEMBLY
IN DISASSEMBLY TOOL
(NO. 450157) AND PRESS
OUT SHAFT (ITEM 8, FIG 4.)
STEP 2:
TO REMOVE BEARING
(ITEM 4, FIG 4) AND LINKS,
PLACE SHAFT ASSEMBLY
IN DISASSEMBLY TOOL
(NO. 450157) AND PRESS
OUT SHAFT (ITEM 8, FIG 4.)
LOCTITE CORP. PRODUCTS
“LOCQUIC – PRIMER N” AND
ADHESIVE “LOCTITE 242” MUST BE
APPLIED TO ITEMS 14, 21, 28, 29
FIG.2, PRIOR TO ASSEMBLY.
FOR “PRIMER – N”:
D. CLEAN PARTS
E. SPRAY THREADS ON SCREWS
AND MATING PARTS WITH
“PRIMER – N”
F. ALLOW PRIMER TO DRY 3-5
MINUTES
FOR “LOCTITE 242”:
D. CLEAN AND DRY PARTS
E. APPLY 242 TO THREADS ON
SCREWS AND MATING PARTS
F. ASSEMBLE AND LET STAND
FOR 30 MINUTES
Figure 4 ECCENTRIC SHAFT ASSAMBLY
6302810: ECCENTRIC SHAFT SET, 0.062" OFFSET
6303170: ECCENTRIC SHAFT SET, 0.042" OFFSET
ITEM PART # DESCRIPTION QTY
1 3070370 BEARING 1
2 3071380 BEARING 1
3 6300650 SPACER 1
4 6300850 NEEDLE BEARING ASSEMBLY 1
5 6302540 DRIVE LINK, RIGHT 1
6 6302550 DRIVE LINK, LEFT 1
7 6302790 BEVEL GEAR 1
6303150 SHAFT, 0.062" OFFSET-STANDARD 1
8 6303160 SHAFT, 0.042" OFFSET-OPTIONAL 1
9 6302530 PIN, BLADE DRIVE – (PIN ONLY) 2

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
AIR MOTOR & PINION ASSEMBLY
MOTOR DISASSEMBLY
STEP 1:
REMOVE ENDCAP (ITEM 7) BY LOCKING IN LOWER
COUNTERBORE OF DISASSEMBLY TOOL (450157). DRIVE
END OF ROTOR (ITEM 8) THRU BEARING (ITEM 1) BY
USING PIN DRIVER (450153, SEE TOOL SECTION).
STEP 2:
REMOVE PINION (ITEM 9) BY SLIDING ROTOR INTO
KEYED HOLE AND USING SPANNER WRENCH (450155).
UNSCREW PINION (RIGHT HAND THREAD). PRESS
PINION OUT OF BEARING (ITEM 6) IN ADJACENT
HOLE.
Figure 5 AIR MOTOR & PINION ASSEMBLY
6302610: AIR MOTOR & PINION ASSEMBLY
ITEM PART # DESCRIPTION QTY
1 3072380 BEARING 1
2 6300570 SPACER RING 1
3 6300690 CYLINDER, AIR MOTOR 1
4 6300700 VANE 5
5 6300720 PLATE, MOTOR FRONT 1
6 6300890 BEARING 1
7 6302410 END CAP, MOTOR REAR 1
8 6302420 ROTOR, AIR MOTOR 1
9 6302480 PINION GEAR 1
10 8611600 PIN 1

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
VALVE ASSEMBLY
Figure 6 6302630: VALVE ASSEMBLY
6302630: VALVE ASSEMBLY
ITEM PART # DESCRIPTION QTY
1 6300770 VALVE PLUG 1
2 6300800 SPRING 1
3 6302570 VALVE STEM 1
4 6302640 BODY, VALVE 1
5 7680080 O-RING 1
6 7680100 O-RING 1
7 7680140 O-RING 1

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
MAINTENANCE TOOLS
PART NO. DESCRIPTION
450135 Pliers
450147 Grease Gun
450153 Pin Driver
450155 Spanner Wrench
450157 Disassembly Tool
450158 Tachometer (Supplied with 1 Conical Tip - No. 450166)
450159 Eccentric Driver
450166 Conical Tip
450171 Hex Wrench (2 mm)
450172 Hex Wrench (2.5 mm)
450173 Hex Wrench (4 mm)
450174 Hex Wrench (6 mm)
450175 Tools - Complete Set (Refer to Picture above for list of tools)
450177 Hex Wrench (10 mm)
630100 Bracket
703409 Socket
720014 Filter-Regulator-Lubricator
731062 Hose Assembly
790304 Air Oil Mist (1 Pint)
790305 Air Oil Mist (1 Gallon)
790306 Air Oil Mist (5 Gallon)
790307 Grease (White Food Grade)(14.5 oz)
Figure 7 MAINTENANCE TOOLS

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] OF 15
[ENGLISH]
GENERAL INFORMATION
MODELS
TURBO-III-A DEHIDER (6303000)
________________________________________________________________________________
SERVICE CENTERS
KENTMASTER LTD. (U.K) KENTMASTER MFG. CO., INC.
16 AVONBANK INDUSTRIAL CENTRE 1801 SOUTH MOUNTAIN AVE.
WEST TOWN ROAD MONROVIA, CALIFORNIA 91016
AVONMOUTH - BRISTOL BS11 9DE UNITED STATES OF AMERICA
UNITED KINGDOM
TELEPHONE: ++ 44- (0) 117- 9235035 TELEPHONE: [phone]
FAX: ++ 44- (0) 117- 9829010 FAX: [phone]

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] Page 12 of 15
NOTICE TO EMPLOYER AND PURCHASER OF TOOL
NOTICE TO SAFETY DIRECTOR
You have purchased a powerful tool that, if misused, can cause severe
injury and harm to your employees. You must instruct your employees in
the safe and proper use of this tool and to follow the safety procedures
and instructions that have been supplied by the manufacturer of this tool.
Please follow the following instructions.
1. Instruct tool operators to test the tool each day before using it to be sure it does not malfunction.
Remove and repair any tool that malfunctions.
2. Instruct tool operators to immediately stop using a tool that malfunctions or is defective.
3. Instruct personnel to immediately remove all tools that malfunction. Be sure to disconnect tool from
power supply.
4. Instruct all personnel to stay clear of tool, and not to stand or walk in front of, or next to tool when in
use.
5. Point out to all personnel the dangers related to the misuse of tool and the importance of following
safety procedures and instructions.
6. Do not make, or allow others to make, alterations or modifications to this tool.
Replace all lost or illegible labels.
7. Follow all safety, installation and maintenance instructions provided with this tool. Establish proper
safety procedures in accordance with local and national requirements to prevent accidental energizing
of tool that can cause injuries.
8. If this tool is sold or change in ownership takes place, you must provide the new owner all safety
instructions, notices and maintenance instructions you were originally provided. You can obtain
additional copies of the instructions from Kentmaster, free of charge upon request.
9. Give copies of instructions to: (A) Tool Operators
(B) Maintenance Supervisor
(C) Clean-up Supervisor

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] Page 13 of 15
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE -DECLARACION DE CONFORMIDAD- ERKLARUNG BEZUGLICH EINHALTUNG DER VORSCHRIFTEN
DICHIARAZIONE DI CONFORMITA . CONFORMITEITSVERKLARING
MANUFACTURED BY: KENTMASTER MFG CO., INC.
1801 SOUTH MOUNTAIN AVE.
MONROVIA, CALIFORNIA 91016
UNITED STATES OF AMERICA
TELEPHONE [phone] FAX [phone]
TYPE / SERIES: DEHIDER
TYPE / SERIE:
TIPO / SERIE:
TYP / SERIE:
TIPO / SERIE:
TYPE / SERIE:
MODEL: TURBO-III-A
MODELE:
MODELO:
MODELL:
MODELLO:
MODEL:
SERIAL NO. RANGE: XXXXX
N SERIE: •GAMA DE No. DE SERIE: •SERIEN-NR.-BEREICH: •NUMERI DI SERIE: •SERIENUMMERS:
This product complies with the following European Community Directives:
Ce produit est conforme aux directives de la Communaute europeenne suivantes:
Este producto cumple con las siguientes Directrices de la Comunidad Europea:
Dieses Produkt erfullt die folgenden Vorschriften der Europaischen Gemeinschaft:
Questo prodotto e conforme alle seguenti direttive CEE:
Dit produkt voldoet aan de volgende EG-richtlijnen:
89/392/EEC, 91/368/EEC, 93/44/EEC, 93/68/EEC
_______________________________________________________________________
The following Standards were used to verify compliance with the Directives:
Les normes suivantes ont ete utilisees pour verifier la conformite avec les Directives:
Las siguientes Normas se usaron para verificar el cumplimiento de las Directrices:
Folgende Normen wurden angewandt, um erfullung der vorschriften zu bestatigen:
Per verificare la conformita del prodotto alle direttive sono stati usati i seguenti standard:
De volgende normen zijn gebruikt om naleving van de richtlijnen te bevestigen:
EN 292
_______________________________________________________________________________________________________
Approved by: ________________________ Date: AUG - 1 - 1995
RALPH KARUBIAN MONROVIA, CA. U.S.A
(Engineering Manager) (Directeur technique) (gerente de ingenieria) (verantwortlicher Konstruktionsleiter) (Responsabile tecnico) (ondersteunend technisch mangar)
FABRIQUE PAR:
FABRICADA POR:
HERGESTELLTVON:
FABBRICATO DA:
VERVAARDIGD DOOR:

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] Page 14 of 15
Kentmaster Worldwide Location
Kentmaster Equipment (Aust) PTY.LTD.
Unit 2,24 Central Court
Browns Plains Qld. 4118
Australia
Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster do Brasil, Ltda.
Av. Dr. Joao Teodoro No. 805
Bairro De Vila Rezende
13405-240 Piracicaba, SP,
Brazil
Telephone #1: (019) 3 413 3113
Telephone #2: [phone]
Fax: [phone]
[email protected]
Kentmaster (IRL) LTD.
Benamore, Dublin Road.
Roscrea,
CO, Tipperary,
Ireland
Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster Equipment (NZ) LTD.
5 Cooper Street
Havelock North
New Zealand
Telephone #1: (64) 6 8777 857
Telephone #2: 0800 KENTMASTER
Fax: [phone]
[email protected]
Kentmaster South Africa (PTY) LTD.
Johannesburg - S. Africa
Unit 54 Sunnyrock Park
Sunrock Close, Germiston
South Africa
Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster (UK ) LTD.
Unit 16 Avonbank Ind. Centre
West Town Rd, Avonmouth-Bristol,
BS11 9DE
England
Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster Mfg. Co., Inc.
1801 South Mountain Ave.
Monrovia, CA, 91016
USA
Telephone #1: [phone]
Telephone #2: [phone]
Fax: [phone]
[email protected]
Kentmaster Omaha
4417 South 139th Street
Omaha, NE, 68137
USA
Telephone #1: [phone]
Telephone #2: [phone]
Fax: [phone]
[email protected]

TURBO-III-A - REV B: 10/27/03
KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA
TELEPHONE: [phone] FAX: [phone] Page 15 of 15
INDEX
OPERATING AND SAFETY INSTRUCTIONS.....................................................................................................................................2
OPERATING INSTRUCTIONS........................................................................................................................................................3
MAINTENANCE.................................................................................................................................................................................3
SERVICE..................................................................................................................................................................................................4
PARTS BOOK...........................................................................................................................................................................................5
MODEL TURBO-III-A DEHIDER ...................................................................................................................................................5
ECCENTRIC SHAFT ASSEMBLY..................................................................................................................................................7
AIR MOTOR & PINION ASSEMBLY.............................................................................................................................................8
VALVE ASSEMBLY ..........................................................................................................................................................................9
MAINTENANCE TOOLS................................................................................................................................................................10
DECLARATION OF CONFORMITY...................................................................................................................................................13
Kentmaster Worldwide Location............................................................................................................................................................14
INDEX.....................................................................................................................................................................................................15
FIGURES - INDEX................................................................................................................................................................................15
FIGURES - INDEX
Figure 1 BLADE REMOVAL...................................................................................................................................................................3
Figure 2 6303000: MODEL TURBO-III-A...............................................................................................................................................5
Figure 3 BOM FOR MODEL TURBO-III-A............................................................................................................................................6
Figure 4 ECCENTRIC SHAFT ASSAMBLY ..........................................................................................................................................7
Figure 5 AIR MOTOR & PINION ASSEMBLY......................................................................................................................................8
Figure 6 6302630: VALVE ASSEMBLY.................................................................................................................................................9
Figure 7 MAINTENANCE TOOLS........................................................................................................................................................10