manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Kenwood
  6. •
  7. Amplifier
  8. •
  9. Kenwood KAC-7406 User manual

Kenwood KAC-7406 User manual

Safety precautions
WARNING
To prevent injury or fire, take the following
precautions:
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and
wiring work to professionals.
• When extending the ignition, battery, or ground wires,
make sure to use automotive-grade wires or other wires
with the range of 5 mm (AWG 10) or more to prevent
wire deterioration and damage to the wire coating.
• To prevent a short circuit, never put or leave any metallic
objects (such as coins or metal tools) inside the unit.
• If the unit starts to emit smoke or strange smells, turn
off the power immediately and consult your Kenwood
dealer.
• Do not touch the unit during use because the surface of
the unit becomes hot and may cause burns if touched.
CAUTION
To prevent damage to the machine, take the following
precautions:
• Be sure the unit is connected to a 12V DC power supply
with a negative ground connection.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid places
with too much dust or the possibility of water splashing.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, first
disconnect the wiring harness.
NOTE
• If you experience problems during installation, consult
your Kenwood dealer.
• If the unit does not seem to be working right, consult
your Kenwood dealer.
Cleaning the unit
If the front panel gets dirty, turn off the power and wipe
the panel with a dry silicon cloth or soft cloth.
CAUTION
Do not wipe the panel with a hard cloth or a cloth
dampened by volatile solvents such as paint thinner and
alcohol. They can scratch the surface of the panel and/or
cause the indicator letters to peel off.
To prevent battery rise
When the unit is used in the ACC ON position without
turning the engine ON, it depletes the battery. Use it after
starting the engine.
Protection function
The protection function is activated in the following
situations:
This unit is equipped with a protection function for
protecting this unit and your speakers from various
accidents or problems that can occur.
When the protection function is triggered, the power
indicator goes off and the amplifier stops operating.
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is sent to
the speaker output.
• When the internal temperature is high and unit won’t
operate.
7Wiring
• Take the battery wire for this unit directly from the
battery. If it's connected to the vehicle’s wiring harness,
it can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when the
engine is running, connect a line noise filter (optional) to
each of the battery wire.
• Do not allow the wire to directly contact the edge of the
iron plate by using Grommets.
• Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing
electricity to the battery‘s negative ·terminal. Do not
turn the power on if the ground wire is not connected.
• Be sure to install a protective fuse in the power cord
near the battery. The protective fuse should be the same
capacity as the unit’s fuse capacity or somewhat larger.
• For the power cord and ground, use a vehicle type
(fireproof) power wring cord. (Use a power wiring cord
with the range of 5 mm (AWG 10) or more.)
• When more than one power amplifier are going to be
used, use a power supply wiring wire and protective
fuse of greater current-handling capacity than the total
maximum current drawn by each amplifier.
7Speaker selection
• Using speakers with smaller input ratings than the
amplifier’s output power would result in smoke
generation or equipment failure.
• The impedance of the speakers that are going to
be connected should be 2 or greater (for stereo
connections), or 4 or greater (for bridged connections).
When more than one set of speakers are going to
be used, calculate the combined impedance of the
speakers and then connect suitable speakers to the
amplifier.
<Example>
Combined impedance
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new power
amplifier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided
below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KAC-7406/KAC-6406 Serial number
US Residence Only
B64-5158-08/00 (KH/EH)© 2013 JVC KENWOOD Corporation
KAC-7406
KAC-6406
4/3 CHANNEL POWER AMPLIFIER
INSTRUCTION MANUAL
Installation
7
Accessories / Accessoires / Accesorios
1ø 4 x 20 mm Self-tapping screws 4
2Speaker level input cable 1
Installation board, etc. (thickness : 15 mm or more)
1Parts included
7
Installation procedure
Since there are large variety of settings and
connections possible according to applications,
read the instruction manual well to select the
proper setting and connection.
1. Remove the ignition key and disconnect the
negative ·terminal of the battery to prevent
short circuits.
2. Set the unit according to the intended usage.
3. Connect the input and output wires of the
units.
4. Connect the speaker wires.
5. Connect the power wire, power control wire
and grounding wire following this order.
6. Install the installation fittings in the unit.
7. Attach the unit.
8. Connect the negative ·terminal of the
battery.
CAUTION
• Do not install in the below locations;
(Unstable location, In a location that interferes
with driving, In a location that gets wet, In a
dusty location, In a place that gets hot, In a place
that gets direct sunlight, In a location that gets
hit by hot air)
• Do not install the unit under the carpet.
Otherwise heat build-up occurs and the unit
may be damaged.
• Install this unit in a location which allows heat to
easily dissipate.
Once installed, do not place any object on top
of the unit.
• The surface temperature of the amplifier will
become hot during use. Install the amplifier in a
place where people, resins, and other substances
that are sensitive to heat will not come into
contact with it.
• When making a hole under a seat, inside the
trunk, or somewhere else in the vehicle, check
that there is nothing hazardous on the opposite
side such as a gasoline tank, brake pipe, or wiring
harness, and be careful not to cause scratches or
other damage.
• Do not install near the dashboard, rear tray, or air
bag safety parts.
• The installation to the vehicle should securely
fasten the unit to a place in which it will not
obstruct driving. If the unit comes off due to a
shock and hits a person or safety part, it may
cause injury or an accident.
• After installing the unit, check to make sure that
electrical equipment such as the brake lamps,
turn signal lamps and windshield wipers operate
normally.
315 mm
232 mm
ø 4.6
200 mm
187 mm
Connection
WARNING Remove the ignition key and disconnect the negative ·terminal of the
battery to prevent short circuits.
WARNING
Particular attention must be given to making good
electrical contact at the amplifier-output and speaker
terminals.
Poor or loose connections can cause sparking or
burning at the terminals because of the very high
power that the amplifier can deliver.
CAUTION
• If sound is not output normally, immediately turn power
off and check connections.
• Be sure to turn the power off before changing the setting
of any switch.
• If the fuse blows, check wires for shorts, then replace the
fuse with one of the same rating.
• Check that no unconnected wires or connectors are
touching the car body. Do not remove caps from
unconnected wires or connectors to prevent short
circuits.
• Connect the speaker wires to appropriate speaker
connectors separately. Sharing the negative wire of the
speaker or grounding speaker wires to the metal body of
the car can cause this unit to fail.
• After installation, check that the brake lamps, turn signal
lamps and windshield wipers work properly.
WARNING
To prevent fire caused by a short in the wiring,
connect a fusible link or breaker nearby the
battery’s positive terminal.
7
Power wire and speaker wire connection
Center unit (CD receiver, etc.)
Power control wire
Battery Ground wire
Battery wire
Protective fuse
Stereo
2-channel + Subwoofer system
Right
A.ch
Right
Left
A.ch
Left
Right
B.ch
Left
B.ch
Lead terminal
Subwoofer

This manual suits for next models

1

Other Kenwood Amplifier manuals

Kenwood R-A100 User manual

Kenwood

Kenwood R-A100 User manual

Kenwood KAC-M3001 User manual

Kenwood

Kenwood KAC-M3001 User manual

Kenwood kac-829 User manual

Kenwood

Kenwood kac-829 User manual

Kenwood KAC-646X User manual

Kenwood

Kenwood KAC-646X User manual

Kenwood L-07C User manual

Kenwood

Kenwood L-07C User manual

Kenwood TL-120 User manual

Kenwood

Kenwood TL-120 User manual

Kenwood KAC-887 User manual

Kenwood

Kenwood KAC-887 User manual

Kenwood KAC-PS150 User manual

Kenwood

Kenwood KAC-PS150 User manual

Kenwood KAC-6401 User manual

Kenwood

Kenwood KAC-6401 User manual

Kenwood KC-209 User manual

Kenwood

Kenwood KC-209 User manual

Kenwood KAC-644 User manual

Kenwood

Kenwood KAC-644 User manual

Kenwood KAC-8406 User manual

Kenwood

Kenwood KAC-8406 User manual

Kenwood KA-895 User manual

Kenwood

Kenwood KA-895 User manual

Kenwood XR1000-1 User manual

Kenwood

Kenwood XR1000-1 User manual

Kenwood KAC-848 User manual

Kenwood

Kenwood KAC-848 User manual

Kenwood MA-5100 User manual

Kenwood

Kenwood MA-5100 User manual

Kenwood KA-7090R User manual

Kenwood

Kenwood KA-7090R User manual

Kenwood R-A100 User manual

Kenwood

Kenwood R-A100 User manual

Kenwood KM-X1000 User manual

Kenwood

Kenwood KM-X1000 User manual

Kenwood KA-880SD User manual

Kenwood

Kenwood KA-880SD User manual

Kenwood KAC-719 User manual

Kenwood

Kenwood KAC-719 User manual

Kenwood KAC-728S User manual

Kenwood

Kenwood KAC-728S User manual

Kenwood GE-80 User manual

Kenwood

Kenwood GE-80 User manual

Kenwood KAC-714 User manual

Kenwood

Kenwood KAC-714 User manual

Popular Amplifier manuals by other brands

StetSom VENOM LINE V 800.4 user guide

StetSom

StetSom VENOM LINE V 800.4 user guide

Soundigital 1600.1 EVO5 owner's manual

Soundigital

Soundigital 1600.1 EVO5 owner's manual

Sony XM-1600GSD Marketing Specifications,... operating instructions

Sony

Sony XM-1600GSD Marketing Specifications,... operating instructions

Taiden HCS-5100Plus Installation and operating manual

Taiden

Taiden HCS-5100Plus Installation and operating manual

Crown Com-Tech CT-210 Reference manual

Crown

Crown Com-Tech CT-210 Reference manual

Mark Levinson 26 operating manual

Mark Levinson

Mark Levinson 26 operating manual

Behringer EUROPOWER EP2000 user manual

Behringer

Behringer EUROPOWER EP2000 user manual

Meridian 558 user guide

Meridian

Meridian 558 user guide

Heritage Audio ELITE Series user manual

Heritage Audio

Heritage Audio ELITE Series user manual

Phoenix Gold iAmp user manual

Phoenix Gold

Phoenix Gold iAmp user manual

Marantz SR8012 owner's manual

Marantz

Marantz SR8012 owner's manual

Pioneer M-LA21 Service manual

Pioneer

Pioneer M-LA21 Service manual

MBL Corona C31 owner's manual

MBL

MBL Corona C31 owner's manual

moon W-10 owner's manual

moon

moon W-10 owner's manual

SoundScope A12 Slim installation manual

SoundScope

SoundScope A12 Slim installation manual

Inter-m DPA-130DC Operation manual

Inter-m

Inter-m DPA-130DC Operation manual

Echo MegaLoop manual

Echo

Echo MegaLoop manual

Panasonic LS-400 Series instruction manual

Panasonic

Panasonic LS-400 Series instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.