Kenwood VZ-7000N User manual

VZ-7000P
VZ-7000N
7-Inch WIDE TELEVISION
INSTALLATION MANUAL
© PRINT IN JAPAN B54-4356-00 (M/H)(+)
03/12 11 10 9 8 7 6 5 4 3 2 1 02/12 11 10 9 8 7 6 5 4 3
INSTALLATION(M/H)-Cover_Eng 02.3.26 6:44 PM Page 1

Accessories
2
External view
......... Number of items
External view
......... Number of items
A........1
H........6
F
CARDIVERSITYANTENNA
WITHBOOSTERCX-A330
ON
OFF
BOOST
........2
G........1
E........2
B........4
C........2
1. To prevent short circuits, remove the key
from the ignition and disconnect the ·
terminal of the battery.
2. Make the proper input and output cable
connections for each unit.
3. Connect the wiring harness cables in the
following order: ground, battery, ignition.
4. Connect the wiring harness connector to the
unit.
5. Install the unit in your car.
6. Reconnect the ·terminal of the battery.
7. Press the reset button.
•If your car's ignition does not come with an
ACC position, connect the ignition cables to
a power source that can be turned on and
off with the ignition key. If you connect the
ignition wire to a power source that
receives a constant voltage supply, as with
battery cables, the battery may die.
•If the fuse blows, first make sure that the
cables have not caused a short circuit, then
replace the old fuse with one with the same
rating.
•Do not let unconnected cables or terminals
touch metal on the car or anything else
conducting electricity. To prevent short
circuits do not remove the caps from
unused terminals or from the ends of the
unconnected cables.
•After the unit is installed, check whether
the brake lamps, blinkers, wipers, etc. on
the car are working properly.
•Insulate unconnected wires with vinyl tape
or other similar material.
•Thoroughly wipe away oil and other dirt
from the installation surface.
Please avoid installation on uneven
surfaces.
•Mount the unit so that the mounting angle
is 30° or less.
2CAUTION
(M4 × 6mm)
Installation Procedure
D........1
VZ-7000_B54_Eng 02.3.26 6:43 PM Page 2

3
Installing the Main Unit
•When mounting the main unit after checking the operation, close the monitor first.
•During installation, do not use any screws except for those provided. The use of different
screws might result in damage to the main unit.
•Damage may occur if a screwdriver or similar tool is used with excessive force during the
installations.
Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction.
NOTE
2CAUTION
Metal mounting strap
(Commercially available)
Self-tapping screw
(Commercially available)
Firewall or metal support
Screw
(M4 x 8 mm)
(Commercially available) Bend the tabs of the
mounting sleeve with a
screwdriver or similar
utensil and attach it in
place.
Installing in Japanese-Made Cars-1
■
Audio Unit.etc
or
Accessory B
Accessory B
When the vehicle bracket is attached as in Toyota, Nissan,
Mitsubishi, and other vehicles that use a hole in the ●position in
the figure below. Not use the Hard
Rubber Frame
(Accessory D).
Screw (Provided with the
Audio Unit.etc)
Screw (Provided with the Audio Unit.etc)
Use the Hard Rubber
Frame (Accessory D).
VZ-7000_B54_Eng 02.3.26 6:43 PM Page 3

Installing the Main Unit
Installing in Japanese-Made Cars-2
■
or
Accessory B
Accessory B
Accessory C
Accessory C
When the vehicle bracket is attached as in Toyota vehicles that use
a hole in the ●position in the figure below.
Fasten Accessory Con both sides as shown in the figure below.
1
Fasten the vehicle bracket.
2
Bend the point of Accessory C, and fasten the bracket.
3
If this device can’t be fastened with screws in the 2 places on the right and left due to the vehicle
bracket shape, use the installation fastener (Accessory C) and fasten the bracket.
Using a screwdriver or pliers bend the right
and left of Accessory Cso that it can be
fastened to the vehicle bracket hole.
Not use the Hard
Rubber Frame
(Accessory D).
Audio Unit.etc
Screw (Provided with
the Audio Unit.etc)
Screw (Provided with
the Audio Unit.etc)
4
VZ-7000_B54_Eng 02.3.26 6:43 PM Page 4

5
Installing and Connecting the Antenna Units
•Attach the antenna to the inner glass surface of the rear window using double-sided tape. Carefully
check the installation location as the tape can only be stuck on once.
•If the surface temperature of the glass of the rear window is low, warm it by turning on the power of
the rear defogger.
A cold window glass surface will weaken the adhesive strength of the double-sided tape.
Also, if installation inside the cabin is performed on a day with high humidity or when it is raining, the
high humidity level will weaken the adhesive strength of the double-sided tape.
•Do not install the antenna in a location where it may obstruct the field of view during driving, such as on
the windshield.
Check the location where the antenna is to be
attached.Clean off any grease or dirt from the
installation location using the supplied glass
cleaner (Accessory G), clean the area with water
and allow to dry.
Clean the glass thoroughly as failure to clean the
glass can not only weaken the adhesive strength
of the double-sided tape, but may also cause it to
come loose.
Remove the protective strips from the antenna
parts and the back of the antenna unit.
Attach the double-sided tape of the antenna parts
and the antenna unit to the rear windshield glass.
Attach the double-sided tape by firmly pressing
down from the top. Secure cables using the
supplied clampers.
After attaching the antenna with the double-sided
tape, allow it to sit undisturbed for 24 hours. Take
care not to apply force to the antenna or allow it to
get wet during this time.
Wire the antenna cable to the main unit.
5
4
3
2
2CAUTION
1
Rear seat
Rear window
Bundle cables with the
clamper bar
(Accessory H)
Antenna parts
Antenna unit
–
+
To the main unit
Ignition cable (Red) ª12V Ignition key switch
Car fuse box
(Main fuse)
ACC
Ground cable (Black) ·(To car chassis)
Battery
Incar antennas have a lower reception sensitivity than antennas intended for outside mounting. The
picture may not appear or may be disturbed if the signal in your area is weak.
2CAUTION
Fuse(1A)
VZ-7000_B54_Eng 02.3.26 6:43 PM Page 5

FM-TX
–
+
AV IN
VIDEO 2 IN
AV OUT
Connection
6
Battery wire (Yellow) ª12V
Ignition wire (Red) ª12V
Parking sensor wire (Green)
Ground wire (Black) ·(To car chassis)
To parking brake detection switch
harness of car
For the sake of safety, be sure to
connect the parking sensor.
2CAUTION
Do not leave this unit in any position where the FM transmitter
antenna is bent or blocked off by metal parts.
2CAUTION
FM transmitter antenna (White)
Center unit
LX-BUS cable
Back view camera,etc
VCR,etc
Fuse(5A)
(Accessory A)
(Accessory F)
Ignition key switch
Car fuse box
(Main fuse)
ACC
Battery
•Visual (Yellow)
•Audio left (White)
•Audio right (Red)
•Acenter unit and KCA-S210A
are necessary to connect a
changer unit. Refer to the
instruction manual of KCA-
S210A for the connection
method. Connect this unit to
terminal “TO CHANGER 2”.
•To connect this unit to KCA-
S210A, extended cable CA-
C2EX or CA-C5EX is
necessary.
•This unit cannot be connected
to any system where two
KCA S210As are connected.
•If this unit and a DAB unit are
connected to a center unit, do
not use KCA-S210A, but
connect this unit to the disc
changer connection terminal
of the DAB unit.
NOTE
Do not connect an LX-BUS cable.
2WARNING
Other Monitor or
Aux input of the
audio unit
VZ-7000_B54_Eng 02.3.26 6:43 PM Page 6

Removing the Hard Rubber Frame
■
Catch
Lock
Accessory E
Catch facing up
Engage the catch pins on the removal
tool and remove the two locks on the
lower level.Lower the frame and pull it
forward as shown in the figure.
When the lower level is removed,
remove the upper two locations.
The frame can be removed from the top
side in the same manner.
NOTE
2
1
Refer to the section “Removing the Hard Rubber
Frame” and then remove the hard rubber frame.
Remove the screw (M4 × 8 ) on the back panel.
Insert the two removal tools deeply into the slots on
each side, as shown.
Lower the removal tool toward the bottom, and pull
out the unit halfway while pressing towards the
inside.
Be careful to avoid injury from the catch pins on the
removal tool.
Pull the unit all the way out with your hands, being
careful not to drop it.
5
2CAUTION
4
3
2
1
Removing the Unit
■
7
Removing the Unit
VZ-7000_B54_Eng 02.3.26 6:43 PM Page 7