4Run two lots of water through the
machine (without coffee) to clean it
out. Fill the tank to the top cup
mark when you do this. See ‘to
make coffee’.
key
permanent filter
filter holder lifting tab
filter holder
anti-drip valve
coffee measuring spoon
hotplate
glass carafe and lid
on/off switch with power light
de-scale warning light
cord storage device
water tank
water tank lid
filter holder lid opening tab
de-scale reset button
to make coffee
1Lift the tank lid and fill with the
required amount of water. The
water level must be between the
top and bottom cup marks. Do not
fill above the MAX level.
●Use cold water. We recommend
using filtered water from a
Kenwood Water Filter as it
reduces limescale and prolongs
the life of your coffee maker.
Never use warm or fizzy water.
2Ensure the filter holder is
positioned correctly.
3Fit either the permanent filter
supplied or a paper filter into the
filter holder. Add the coffee, use
the spoon provided (approximately
1 level spoon per cup or to taste).
4Close the lid and put the carafe on
the hotplate.
NOTE: The lid must be fitted
to the carafe in order to
operate the anti-drip valve.
5Plug in and switch on – the neon
light will come on.
6Don’t remove the carafe until
brewing has finished.
●The separate element for the
hotplate ensure that the coffee is
maintained at the correct
temperature after brewing.
●The hotplate will keep your coffee
hot, but the sooner you drink it,
the better it will taste.
●Your coffee maker will keep the
coffee warm and then
automatically switch off after 2
hours.
●If you haven’t used the machine
for a while, run one lot of water
through it (without coffee) to clean
it out. Fill the water tank to the top
cup mark when you do this.
care & cleaning
●Always switch off, unplug and
allow to cool before cleaning.
●Never put the machine in water or
let the cord or plug get wet.
●Don’t wash parts in the
dishwasher.
●Wipe with a damp cloth, then dry.
Don’t use abrasives - they’ll
scratch the plastic and metal
surfaces.
removable parts
●Wash in hot soapy water, then dry.
descaling
After 90 brewing cycles the de-
scale warning light will come on
and flash to indicate that the coffee
maker requires descaling (see ‘to
descale’)
safety
●Watch out for steam and
never lift the filter holder lid
during the brewing cycle.
●Never touch the hotplate.
●Always lift the filter holder lid using
the opening tab .
●Never touch hot surfaces.
●Keep children away from the
machine. And never let the cord
hang down where a child could
grab it.
●Wind excess cord into the cord
storage device .
●Never use a damaged machine.
Get it checked or repaired: see
‘service and customer care’.
●Never put the machine in water or
let the cord or plug get wet - you
could get an electric shock.
●Switch off and unplug:
●●before filling with water
●●before cleaning
●●after use.
●Never leave the machine on
unattended.
●Don’t let the cord touch hot parts.
●Always make sure there is water in
the tank before switching on.
●This coffee maker is only suitable
for use with the type of carafe
supplied.
●Do not leave the machine
switched on with an empty carafe
on the hotplate.
●Never put the carafe in the
microwave.
●This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of
the appliance by a person
responsible for their safety.
●Children should be supervised to
ensure that they do not play with
the appliance.
●Only use the appliance for its
intended domestic use. Kenwood
will not accept any liability if the
appliance is subject to improper
use, or failure to comply with these
instructions.
before plugging in
Make sure your electricity supply is
the same as the one shown on the
underside of your machine.
Important (UK) only
●The wires in the cord are coloured
as follows:
Green and Yellow = Earth
Blue = Neutral
Brown = Live.
●The appliance must be protected
by a 13A approved (BS1362) fuse.
●WARNING: THIS APPLIANCE
MUST BE EARTHED.
Note:
●For non-rewireable plugs the fuse
cover MUST be refitted when
replacing the fuse. If the fuse
cover is lost then the plug must
not be used until a replacement
can be obtained. The correct fuse
cover is identified by colour and a
replacement may be obtained
from your Kenwood Authorised
Repairer (see Service).
●If a non-rewireable plug is cut off it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise if an unwanted
non-rewireable plug is
inadvertently inserted into a 13A
socket outlet.
●This appliance complies with
European Economic Community
Directive 89/336/EEC.
before using for the first
time
1Remove all packaging.
2Wash the parts: see ‘care and
cleaning’.
3Wind excess cord into the cord
storage device .