Kenwood SRC-702 User manual

&
STEREO SYSTEM RACK
SRC-702 ©
ASSEMBLY INSTRUCTIONS
IMPORTANT:
* Before operating your new KENWOOD product, read through this assem-
*bly manual carefully to get the most out of it.
® Save this assembly instructions.
Before Assembling
© Be sure to check that all parts are accounted for before disposing of the
packing case.
© A Phillips screwdriver and a mallet are required for assembling.
® Be carefull not to damage the floor and rack.
*
IMPPRTANT SAFEGUARDS
ACaution : Read this page carefully to keep your safety.
Please redf’ ~ of the safety and operating instructions before operating this
unit. For bs, esults, follow all warnings placed on the unit and adhere to the
operating and use instructions. These safety and operating instructions should
be retained for future reference.
1. Suffocation — After taking the unit out of the polyethylene bag, be sure
to dispose of the polyethylene bag out of the reach of children. Otherwise,
they may play with the bag, which could cause hazard of suffocation.
2. Water and moisture — Do not place a liquid container, such as a vase and
water basin, on the unit. Also avoid installing the unit in a place subject
to dampness.
3. Heat — Do not install the unit near a source of heat, such as a heater, or
under direct sunlight.
KENWOOD
KENWOOD CORPORATION
©PRINTED IN U.S.A B61-0518-00(K)(TCA)
R0264
t
--.-Notes on Assembling
* During assembling, be sure to verify the numbers stamped on the boards.
Mount the rear panel after assembling the side panel on the bottom shelf
at a right angle.
When mounting the top shelf and kick plate on the side panel, use glue
for adhesive. Be sure to remove any excess glue before it dries.
!f the amplifier wobbles when its key switches are pressed, insert a woo-
den dowel into the hole on the side panel and fix the rear of the amplifier.
Handling Precautions
¢ Tempered glass is used for the glass doors for providing sufficient strength.
However, pay attention not to apply excessive force or to scratch the doors.
Cracking or breaking of the glass may occur.
When moving the cabinet, remove all the components from the rack be-
fore carrying the cabinet. Also do not grasp the top shelf when carrying.
To allow head radiation from the components, leave a space of 4 inches
between the cabinet and wall.
Do not place the cabinet in a location subject to direct sunlight or near a
heater, an air-conditioner, or a place with high humidity.
4. Impact — Avoid placing the unit on an unstable surface
horizontal surface not subject to excessive dirt or vibrat.
rs
wa
a it ona
5. Modification — Do not attempt to open or modify the unit, for this could
cause fire hazard or malfunction.
o
. Cleaning — Do not use thinner, benzine or alcohol. When cleaning the unit,
wipe with a soft, dry cloth.
7. Abnormal smell — In the event the unit generates smoke or abnormal smell,
immediately switch the power OFF and unplug the power cord. After this,
please contact your dealer or nearest service station as soon as possible.
POWER OFF!

PARTS
LIST
MODEL
SRC-702
©
-
-
ASSEMBLY
INSTRUCITONS
Item
ASSEMBLED RACK
Dimensions
Unit : inch (mm)
Description
(3) So
Part No.
O
$0033
41” (1042)
Net
weight:
60.6
Ibs.
(27.5
kg)
WOODGRAIN UP
WOODGRAIN SURFACES
DOWN AND FORWARD
(X) Glass Door

STEP 3
BLACK SIDE FACING INWARD
I
|
aul
ion
STEP
4
"cence
STEP
5
AND FORWARD
BLACK SIDE
FACING INWARD
CONTINUED NEXT PAGE

fad
ASSEMBLY INSTRUCTIONS
Ilene
w
BLACK SURFACES UP AND FORWARD
|
| ITEM DESCRIPTION QTY. PART NO. ITEM DESCRIPTION QTY. PART NO. 2
| A LEFT SIDE PANEL 1 XWO0506 M MAGNET CATCH 1: POO11 |
B BOTTOM BOARD 1 XW0319 N SHELF PIN 4 P0053 |
| Cc RIGHT SIDE PANEL 1 XW0505 0 RUBBER SPACER 4 GO067 |
| D KICK PLATE 1 XW0497 P WOOD DOWEL 9 Wwo0092 |
| E TOP BOARD 1 XW0504 Q WOOD DOWEL 2: W0398 |
| F BACK BOARD 1 xw0491 R GLUE 1 GOO12 _ lfany parts are MISSING or DAMAGED in this |
| G SHELF A 1 XW0432 $s SHELF PIN 4 BOO15 package, circle the item (s) needed on the parts |
l H SHELF B 1 XW0318 T UPPER HINGE 1 M0026 Ns. Print your name, address, and phone num-
I CONFIRMAT SCREW 4 $0033 U LOWER HINGE 1 M0027 __ ber in the area to the left and mail to TOCABI |
| J SCREW 16 $0034 Vv CATCH PLATE 1 M0011 ~ AMERICA, 9375 Custom House Plaza Road, |
| K ALLEN WRENCH 1 M0018 W ~~ CATCH PLATE PAD 1 GO0047 Suite | San Ysidro, CA 92173, or call |
| L HINGE INSERT 2 POO54 X GLASS DOOR 1 GOO78 § (619)-661-6136. |
—