KERUI KR-K7 User manual

KR-K7 User manual
23
System setup
11.1 Delay setting
Picture 11-1
Arm Delay
Gives the ability to use the arm key on the panel when leaving the guard area to delay the arming for
x seconds. You can set a delay of 0-255 seconds. In the delay arming status, the host beeps every
second till the delay is over and goes into arm status. The value zero means no delay on arming.
Alarm Delay
Gives the ability when entering the guard area to delay the alarm for x seconds. You can set a delay of
0-255 seconds. In the alarm delay status, the host beeps every second till the delay is over. The value
zero means no delay on alarm.

KR-K7 User manual
24
11.2 Auto Arm/Disarm
On the page of Auto Arm/Disarm, you can program the first 8 zones to automatically Arm/Disarm. The
setting supports “time”, “arm/disarm” and “day of week” choice.
Picture 11-2
Delete auto arm/disarm
To delete auto arm/disarm for a zone choose the zone that you want to delete. A dialog [edit/ delete]
will pop up. If you select [edit], you can edit the settings; if you choose [delete] it will delete the auto
arm/disarm.
Picture 11-3
To delete all groups auto arm/disarm click in the top right corner [delete all].

KR-K7 User manual
25
11.3 Volume adjustment
Picture 11-4
Voice volume: Ability to set the voice prompt volume (0-7) of the panel. 0 means voice prompt mute,
7 means the maximum volume. The default voice volume is 5.
Alarm volume: Ability to set the alarm volume (0-7) when the panel alarms. 0 means alarm mute, 7
means the maximum alarm volume. The default alarm volume is 5.
11.4 Siren/Ring time
Picture 11-5
Siren time: Ability to set the number of minutes the alarm sounds. Make sure you meet the
regulations in your area about duration of the alarm sound.
The maximum is 20 minutes, 0 indicates no siren, The factory default is one minute.
Ring times: When the host is remotely calling (during alarm) it will wait for an answer after the
specified number of ring tones. Can be set up to 20 times, entering 0 to disables the remote control
function. 20 indicates that the host waits 20 continuing rings to answer the call.
The factory default is 1.

KR-K7 User manual
26
11.5 Arm/Disarm SMS
Picture 11-6, in the disarming SMS notification page the user can select the desired SMS notification.
Make sure to set the alarm numbers when enabling this function.
Picture 11-6
11.6 Key Tone
Picture 11-7
When the key tone is on, pressing the host screen will trigger a "beep" a sound. The factory default is
On.

KR-K7 User manual
27
11.7 Screensaver
Picture 11-8
On the Screensaver settings page there are six options, "30 seconds", "1 minute", "2 minutes" "5
minutes", "10 Minutes", "never". The factory default is 30 seconds, indicating that without any
operation during 30 seconds, the host display will automatically turn off and be locked. Choosing
“never” means that the display never turns off or will be locked.
11.8 Language
On the ‘System setup’ page under ‘language’ (System > Language) you can choose two languages
（Chinese & English).
11.9 Security
Picture 11-9
As shown in Picture 11-9 users can set [User password], [administrator password] and [Keypad Lock]
User password: Is 4 digits to restrict the access of others. The factory default user password is 1234.
When Keypad lock is “on”, enter your user password can only for open / close / stay arming operation.

KR-K7 User manual
28
Administrator Password: Is 6 digits and used to enter the menu to program the host. This password
is also used for remote setting, telephone, SMS settings and query using the app. The factory default
administrator password is 123456.
Keypad Lock: Choosing Keypad lock ON, in the upper right corner a lock icon on the host displays.
The host automatically will be locked after 20 seconds of no use. When in locked state the screen can
only be operated for Arm / Home / SOS functions. To disarm and other operations the ‘Please enter
password’ screen appears (figure 11-10), and you must enter a password to unlock the keyboard.
Host keypad lock factory default is OFF.
Picture 11-10
Pin code: Used to enter the pin code of the installed SIM card.
11.10SMS Reply
In the page of SMS Reply, you can choose “YES” or “NO”. When enabling SMS notifications or using
the App by Phone connection, choose “YES” so the host can send feedback SMS to sender. The
default status is on “YES”
Picture 11-11

KR-K7 User manual
29
11.11Power Alarm
In the settings page of Power Alarm (Picture 11-12), there are 4 choices: Panel Power Off, Panel
Power On, Panel Low Battery, and Sensor Low Battery.
Picture 11-12
Panel Power OFF
When “Panel Power Off” is chosen, four choices pop up:
Voice: Panel will say that the power is Off
Siren: The siren will be activated
SMS:A SMS is send that the power is off
Call: The telephone numbers are called.
After setting the Panel Power Off function, the panel will warn you that the power is off, to avoid the
unnecessary loss of security functions.
Panel Power ON
The same as Panel power OFF, user can choose same choices according to their needs.
Panel Low battery
The same with above, user can choose same choices according to their needs.
Detector Low battery
The same with above, user can choose same choices according to their needs.

KR-K7 User manual
30
11.12Ready to Arm
This function checks if all door sensors are closed when arming. A door icon will be shown in the top
menu of the host (red color when open, white when closed). When function switched ‘ON’ and a door
is open, the system cannot arm and a voice alert sounds “XX zone on”. You can’t arm the system untill
all door sensors are closed. If you set this function ‘OFF’, no matter a door is open or close, the
system can be armed.
Picture 11-13
11.13Keypad arm/disarm
Enables the use of the keypad to arm or disarm. When off these functions can only be performed
using a remote controller or the app.
Picture 11-14

KR-K7 User manual
31
11.14Contact ID
CID No. is the account which is shown on the network center.
Picture 11-15
11.15Restore factory
Restores the K7 panel to the factory defaults using three options:
Delete Remotes：Delete all programmed remote controls.
Delete Sensors：Delete all programmed sensors.
Restore setting：Except the added remote controls, sensors, smart sockets, sirens and
language all other settings will be restored to factory setting.
Picture 11-16

KR-K7 User manual
32
11.16Phone Call
As Picture 11-17. In the Call Menu page user can dial any number, like a normal phone.
Picture 11-17
11.17Recording
When alarming, the recording message will sound first when a telephone number is dialed.
How to set the recording:
As Picture 11-18 shows，press button to record for a maximum of 10 seconds.
The voice alert should be clear and simple, for example: “this is ** home, intruder break into, please
help”. Message is saved automatically. You can press the recording button to overwrite the previous.
Picture 11-18
After the recording is over, press play button to hear if the recording is right or not.

KR-K7 User manual
33
11.18Alarm Log
All alarms, arms and disarms are logged for audit use.
Picture 11-19
Arm / Disarm Log
As shown in Picture 11-20. In this page the last 99 arm/disarm recordings are shown, for each
recording it shows the date, time and the device (Host, remote control, sms, wifi, gprs) used for
arm/disarm/home.
Picture 11-20

KR-K7 User manual
34
Alarm Log
As shown in Picture 11-21. This page shows the 15 most recent alarm events by the alarmed zone,
date, time, etc.
Picture 11-21
11.19About me
In the page ‘About Me’, the Version No, UI, IMei and MAC address are shown.
Picture 11-22

KR-K7 User manual
35
SMS Setting and Command Chart
In addition to change settings through host menu or the K7 app, SMS using a phone or other device
can be used to set panel settings using SMS codes. The syntax is as follows:
[System Password][Command No][parameter1][parameter 2][parameter 3][parameter 4][parameter 5]
All commands begins with system password, in below chart the system password is 123456. Make
sure you change the default system password, to prevent others from changing your alarm settings.
Also enable the SMS Reply function so you will receive a conformation reply SMS.
Setting name
Command
No
Parameter
1
Parameter
2
Parameter
3
Parameter
4
Parameter
5
Example code
(Setting changed)
Disarm
0
1234560
(Disarm)
Arm
1
1234561
(Arm)
Stay Arm
2
1234562
Call the panel or
monitor
3
1234563
(Call back the panel)
Wireless Socket On
4
1234564
(Ganged Socket On)
Ganged Socket Off
5
1234565
(Ganged Socket Off)
Query Status
6
1234566
(Inquiry arm/disarm，
power., linkage socket)
Set Phone
No.
10
01~08
no.01~08 phone
number
13899998888
123
Alarm Tel
Alarm SMS
CID
123456100113899998888,
12
(Sets the first phone
number for call/SMS)
Delete
Phone No.
11
00 or 01~08
Do not delete all
phone numbers!
1234561005
(Deletes the No.5 phone
number)
Check
Phone No.
11
No1~8
1234561108
(Checks No.8 phone
number)
Set the Zone Type
12
no.01~99 zone
1- Siren when
arming
2-Do not Siren
when arming
1-Normal zone
2-Stay zone
3-Smart zone
4-Emergency zone
5-Close zone
6-Doorbell zone
7-Elder Zone
1-Medicial
2-Fire
3-Robbery
4-Silence
5-Burglar
6-Perimeter
7-Gas
12345612511141
(Sets 51 zone, Siren，
common, silent)

KR-K7 User manual
36
Check Zone Type
12
01-99 Zone
1234561255
(Check No.55 zone type)
Set the Remote
Control sound
13
no. 01~99 remote
control
1-Sound on
0-Sound off
12345613200
(No 20 remote control
without sound)
Check the Remote
Control
13
No.01~99 remote
control
1234561333
(Check Sound of No. 33
Remote Control ON/OFF)
Control Appliances
14
No.01-20 smart
socket
1-Close
0-Off
12345614011
(No. 1 smart socket
Closed)
Check Appliances
14
No.01-20 smart
socket
1234561405
(Check no.5 smart socket)
Appliances timing
setting
15
No. 01-40 Timing
01-20 Smart
Sockets
1 - Timing close
0 - Timing open
08:00
Time
1234567
Week
123456150103108001234
5
(Set no.1 group Timing, at
8:00 on Day 1 No. 3 Smart
Socket Timing Close)
Delete
Scheduling
Appliance Setting
15
00 or 01-40
(00 deletes all
timing settings)
1234561502
(Delete second Group
Appliance Timing)
Check Scheduling
Appliance Setting
16
01-40 Scheduling
Group
1234561601
(Check the first Group
Appliances Timing Set)
Delay
Setting
17
1-Delay Alarm
2-Delay Arm
0~255
12345617136
(Sets Delay Alarm Period
as 36s)
Check Delay
Setting
17
1-Delay Alarm
2-Delay Arm
123456172
(Check Delay Arm Period)
Scheduling
Arm/Disarm Setting
18
01-08
Scheduling
Group
1-Timing Arm
0-Time Disarm
08:00
Time
1234567
Week
12345618011080012345
(Set the first group at 8:00
on day 12345)
Delete Scheduling
Arm/ Disarm Setting
18
00 or 01-08
Scheduling
Group
(00 deletes all
timings)
1234561802
(Delete the second Group
Timing
Arm/Disarm)
Check Scheduling
Arm/ Disarm Setting
19
01-08 Scheduling
Group
1234561901
(Check the first Group
Timing Arm/Disarm Set)
Time &Date Setting
20
20160127
203000
123456202016012720300
0
(Set Time as 20:30:00 on

KR-K7 User manual
37
27 Jan. 2016)
Check System
Time and Date
20
12345620
(Check System Time&
Date)
Set Volume
21
1-Voice
2-Volume
3-Alarm
4-Volume
1~7
(Level)
1234562125
(Set Alarm Volume Level
as 5)
Check Volume
21
1-VoiceVolume
2-AlarmVolume
123456211
(Check Voice Volume)
Set Alarm Siren
Period
22
0-20Mins
1234562205
(Set Alarm Siren Period as
5 minutes)
Check Alarm Siren
Period
22
12345622
(Check Alarm Siren
Period)
Set Ringing Times
23
00-20
1234562308
(Set Ringing 8 times)
Check Ringing
Times
23
12345623
(Check Ringing Times)
Set Password
24
1-UserPassord
(4digits)
2-System
password
（6digits)
1234 or
123456
123456242345612345678
(Set User Password as
345678345678)
Check Password
24
1-User Password
2-Admin
Password
123456241
(Check User Password)
Set CID Number
25
1234
(4digits CID No)
123456251234
(Set CID Number to 1234)
Check CID Number
25
12345625
(Check CID Number)
Set Arm/ Disarm
Upload Center
26
123/0
1-Arm upload
2-Disarm upload
3-Stay upload
0-No Upload
1234562613
(Set Arm, STAY Upload,
Disarm Not Upload)
123456260
(No Upload)
Check Arm/ Disarm
Upload Set
26
12345626
(Check Arm/ Disarm
Upload Set)
Set Zone SMS
Message Content
27
01-99
(1-99 Zone)
ABCDEFG
(SMS
Contents less
Than 25
1234562705ABCDEFG
(Set Zone 5 Alarm
Message)
(Content as ABCDEFG)

KR-K7 User manual
38
characters)
Check Zone SMS
Message Content
27
1-99 Zone
1234562705
(Check Zone 5 Message
Content)
Arm/Disarm SMS
28
123/0
1-Arming form
2-Disarm inform
3-Stay inform
0-No inform
1234562812
(Set Arm, Disarm Inform
STAY not Inform)
123456280
(No Inform to Arm/Disarm)
Check Arm/Disarm
SMS Inform Set
28
12345628
(Check Arm/Disarm SMS
Message Inform Set)
SMS reply set on/off
31
0-No Reply
1-Reply
123456310
(Set SMS Inform when
Read, Not Disarm)
Mobile Network
setting
32
0—Off
1—On
Access point
Server IP
COM port
Account No
（Six-digit）
123456321,CMNT,,,121.5
0.34.7,6501,000123
(When the mobile network
on，Access point is
CMNT,Server IP
121.50.34.7，COM
Port 6501，Account
000123)
Set Ready To Arm
33
0-Close
1-Open
123456331
(Open Ready To Arm)
Set Ganged Siren
Ganged Socket
34
1-Wireless Siren
2-Smart Socket
0-Ganged
1-Not Ganged
12345620
(Set Socket Not Ganged)
12345611
(Set Siren Ganged)

KR-K7 User manual
39
GPRS Management
A network alarm client management software is released by our company, which is low cost but
powerful and can be used by alarm centers, security service companies, police, military, financial
industry, museums and other environments.
13.1 Login Management Center
Management host is also called Management terminal, which is one important man-machine
communication platform. On this platform users can deal with alarm events, user management, event
operation, document management and so on.
Start the management terminal by double-click the icon of management terminal on desktop.
Input the code and password of operator, and IP address, click “Confirm”, the main menu of software
will appear after the data loaded.
13.2 Add new user
Click “Add new user” in “User management”, one “add new user” message pop up
Choose the type of device: KR-8218E, click it to show in the frame of device type. Choose the
partition number, input the account of device, click “Confirm”, one new user record will be built in user
data, and it will appear in the users window.
13.3 Alarm System Networking
Send one SMS to the alarm system, set the connecting point of network and IP address of data
service, port number and account. The SMS format is:
<password>+<32>+<0/1>+<,network access point,>+<IP Add>+<,port,>+<account>
For example: 123456321, CMNT,121.50.34.7,6501,000123
123456 default password
32 setup instruction
1, turn network
CMNT,,, network access point
121.50.34.7 IP Address
,6501, port
000123 the account.
Noted: 1. all “,” in the instruction must be input in English status.
2. The account for management terminal must be the same with the alarm system account.

KR-K7 User manual
40
APP K7
There is an app called K7 available for Android and iOS to remotely use
and configure the KR-K7 alarm panel. There are two ways to connect the
app, by phone (worldwide coverage) or by WIFI (Local). Within the app
you can switch between connection easily so you can use both at the
same time, so WIFI when at home and phone when away.
Connection using Phone: No need for a WIFI connection, but you need to have a 2G/3G sim card
installed in the KR-K7 panel, because the app sends actions towards the KR-K7 using SMS and the
panel receives and answers by sending SMS messages back to your phone. Besides SMS also the
phone connection can be used to contact the KR-K7 panel in order to ‘listen’ or see what is
happening. So make sure you have enough SMS credits on your sim for both phone and panel.
Connection using WIFI: You need he KR-K7 panel to be connected to the same WIFI network as
your phone. No additional costs
Scan the QR code to download the app or search"K7" in App Store.
After installation you need to register an account or connect your mobile phone during first use of the
app. For example: Android Version, there are two ways: Mobile Number and Email register
14.1 Phone Register
When register by phone select the ‘Switch to GSM’ option. Notice:
verification code will be sent to the phone in 60 seconds through
message. If not received, please re-access.

KR-K7 User manual
41
Host number: Enter the telephone number of your Sim card installed
in the KR-K7 panel.
User name: Set a user name
Password (confirm): Enter the password of your admin account on
the KR-K7 panel
Press the checkmark in the top right corner
14.2 Email Register
Email register is needed to make sure that your password can be
retrieved in the future.
Notice: There isn't need verification code in email register. Please
make sure use effective email address.

KR-K7 User manual
42
14.3 Binding equipment
Under App page, If the device shows under {on-line device page}, after clicked on the {unbound
device page}, it means successfully. Mobile phone can detect the other device automatically under the
LAN.
Online device: The device enters the network successes, and the
network well, the cell phone bind with network. When connected by
phone it will show as ‘remote online’, when connected by WIFI it will
show as ‘LAN online’.
Unbound device: The device enters the network successes, and the
cell phone connects with the network well, but the device didn’t bind
with the cell phone at before.
Off-line device: The device enters the network successes, and cell
phone had already bound with network, but the device didn’t enter the
network.
14.4 Password of Device
Clicked on any device under (On-line devices), input correct passwords (original password: 123456),
click OK, you will enter into the operation interface. You can operate the control panel in any place
which without network.