KESO KG-5 User manual

Hand Operated Electrostatic Eliminator
KG-5
High Frequency AC Ion Air Gun

Read carefully before using
■Thank your very much to buy the KG-5 ion air gun
■Please read the operation method carefully before operating it.
■Please put the product specification in a place where it can be seen
at any time.
■Please use it according to the method recorded in the specification
and operating manual; otherwise, the company assumes no
responsibility.
Please observe the following precautions for security
1. Make sure the connector is linked before use
2. Please use clean air without oil and water
3. Please stop using the gun if the air contains organic solvent, organic
phosphate engine oil, sulphurous acid air, chlorine and acid
4. Please do not use nozzle head from other source, and do not make
change of the head, otherwise it will cause functional problems
5. The life span of the emitter needle is depend on the environment,
dirty needle will cause function decease, need to clean in a certain
time
6. Make empty and clean inside of the tube if equip with air tube
7. Precise electronic parts are installed within the product. When
using the product, please don’t knock, fall down or hit against the
product, or impose too much impact force to the product; otherwise,
even the product appearance is not damaged, its internal may also be
damaged or the operation may be abnormal.
Brief Introduction of the Product
1. Hand held type, small size, light weight, flexible and safety for
handle, equip with HV normal and HV abnormal running function
2. Make sure the connector is linked before use
3. High frequency AC type, blow out the plus and minus ions by
compressed air, can destaticizing from point to wide scope, various
nozzle heads for optional
Product features
1. Built-in high voltage system, automatic ion balance 0±15V
2. Filter fixed inside, increase the clean rate of compressed air and

decrease the voice. Piston design of the air flue, huge volume enable
short decay time
3. Various nozzle heads optional for different application
4. Trigger Arc design in accordance with ergonomics, convenient for
operation
5. “Electric & air synchronous” and “Air inlet firstly, electric
secondly” shift by sliding the trigger
Note: The ion air fun has function of static eliminating and dust clean
Compressed air range: 0.05-0.5MPa
1) Adopt 0.1-0.3MPa for static eliminating purpose
2) Adopt 0.3-0.5MPa for dust clean purpose
Product structure diagram

Dimension
Product detailed diagram

1
Left housing ABS
12
C type latch
2
Right housing ABS
13
Trigger
3
Hanger
14
Electric & air control switch ABS
4
HV Box
15
Inching switch
5
L type air flue (Fireproof ABS)
16
Laser head
6
Spring
17
Inlet air base
7
Straight air flue (Fireproof ABS)
18
Spray head
8
Air flue stop valve
19
Body power board PCBA
9
Anechoic block
20
HV control board PCBA
10
Air terminal
21
Trigger fulcrum
11
Electric and air connecter
22
Functional indicator display
Electric & air control switch
Down: Air inlet firstly, electric secondly (Optional for flammable and
combustible industry)
Upper: Electric & air synchronous

Different nozzle head for option
Technical parameters:
Model:
KG-5
Input power
DC24V
High voltage output:
2200V
Current consumption
500mA
LED
indicator
Power normal
LED green light
HV normal
LED blue light
Clean reminder
LED yellow light
HV abnormal
LED red light
Ion generation mode
High Frequency AC Corona type
Ion Balance:
0±15V
Operation Temperature:
0oC-40oC
Diameter of the air pipe
φ6
Compressed air range
0.05-0.5MPa
Overall size /mm:
147*118.1*33.3mm
Weight:
175g

Ozone concentration:
Below 0.03ppm(distance 150mm)
Length of power adapter cable:
2m
Hose diameter:
Φ6 trachea
Filter precision:
0.2μm
Filter efficiency:
99%
Anti-static test condition
Operating voltage: DC 24V Test voltage:±1000V-±100V
Environment Temperature:0℃±40℃
Distance
150mm
300mm
Decay time
Positive
0.5s
0.8s
Negative
0.6s
0.9s
Residual
voltage
Positive
<0±15V
Negative
Power and air tube connect drawing
Connect is rotate type and disassemble, position in the accurate point and
fasten well for a fine performance
Maintenance
Screw down the nozzle head, take out the ceramic tube, clean the
tungsten needle with non-dust cloth dipped with ethanol.
O type ring is consumable parts, change with new one if damaged or air
leakage

After-sales Service
1. Service in the Warranty Period
The warranty period of the products sold by the company is one year.
Within one year since the product is sold, any fault caused due to its
component materials and process problems should be repaired by the
company freely (except quick-wear parts).
2. Service after Warranty Period
All products sold by the company will still be reparied free of labor
cost (only charging part cost) after warranty period to protect
customer’s interest.
The company maintains the right of modifying the above product
property parameters and technology at any time without further
notification.
Package Content Confirmation
The package contains the following components. Before using them,
please confirm whether all goods are complete.
1. Ion air gun………………………………………..…………….1 set
2. Power adapter…………………………………….…………….1 pc
3. Electric wire and air tube………………………….……...…...1 pc
4. O type ring..………………………..………………….………3 pcs
5. Warranty card……………………..………………….….……1 pc
6. Inspection report……………………..…………..….………..1 pc
7. Certificate of conformity…………..…………………..……..1 pc