KEYKING TA7002P-X User manual

User Manual
Thank you for selecting Keyking products. Please read this manual thoroughly before using.
TA7002P-X Time & Attendance Standalone
KEYKING GROUP LIMITED

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 2 of 28
Index
................................................................................................................................................................................
Chapter1 Introduction .......................................................................................................................................... 3
1.1 Summary ................................................................................................................................................ 3
1.2 Features .................................................................................................................................................. 4
1.3 Application Mode................................................................................................................................... 5
Chapter2 Wiring Diagram.................................................................................................................................... 7
2.1 TA7002P-X Appearance......................................................................................................................... 7
2.2 Wiring Diagram...................................................................................................................................... 8
2.3 Lock Wiring Diagram............................................................................................................................. 9
2.4 RS485 Net Bus..................................................................................................................................... 10
2.5 TCP/IP Network....................................................................................................................................11
Chapter3 Instructions ......................................................................................................................................... 13
3.1 Clock Configuration............................................................................................................................. 14
3.1.1 Edit Time................................................................................................................................... 14
3.1. 2 Edit Alarm................................................................................................................................ 14
3.2 Card Configuration............................................................................................................................... 15
3.2. 1Add Card .................................................................................................................................. 15
3.2. 2 Delete Card............................................................................................................................... 16
3.2.3 Del All Cards............................................................................................................................. 16
3.3 System Configuration........................................................................................................................... 17
3.3.1 Language Setting....................................................................................................................... 17
3.3.2 Menu Password ......................................................................................................................... 18
3.3.3 Reader Settings.......................................................................................................................... 18
3.3.4 System Info Configuration........................................................................................................ 19
3.4 Delete ................................................................................................................................................... 21
3.4.1 Clear Event................................................................................................................................ 21
3.4.2 Clear Card ................................................................................................................................. 21
3.4.3 Door Parameter Initialize .......................................................................................................... 22
3.4.4 Clear All .................................................................................................................................... 22
3.5 Door Open Mode.................................................................................................................................. 22
Chapter 4 Installation......................................................................................................................................... 24
4.1 In the Wall............................................................................................................................................ 24
4.2 On the Wall........................................................................................................................................... 25
4.3 Without USA Gang Box....................................................................................................................... 26
Chapter 5 FAQ ................................................................................................................................................... 27

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 3 of 28
Chapter1 Introduction
1.1 Summary
TA7002P-X & TA7003NT are belong to Standalone family, but TA7002P-X a new outstanding
T&A standalone controller with OLED screen and support POE. The OLED screen will display
time and staff ID info. This system greatly improved the T&A simplicity and offered cost
saving on traditional tags. When TA7002P-X works as an access controller, the traditional key
is no longer needed, employees can enter their special space by flashing authorized cards.
TA7002P-X can by itself control a door, both in and out, at least one reader is needed for one
side, and the other side can be controlled either by a reader or a Rex Button. This system
provides a more convenient and secured access environment, it also makes it possible for
managers to verify the attendance in time. TA7002P-X is compatible with a big range of
applications including, building management, enterprise management, government, military and
prison.
Model Definition:
TA7002P-P------Built in Proximity Reader (EM, HID, Awid, KKID)
TA7002P-U------Built in Mifare\CPU Card Reader；
X = P or U.
Supported Card Type:
E：EM Card；Exp EM4100，TK4100 Series.
H：HID Card；Exp: 1326、1386 Series.
U：FM1208 CPU Card，Philips S50，Mifare-1 Compatible
TA7002P-X (POE Standalone)
TA7002P-X Diagram

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 4 of 28
1.2 Features
1. TA7002P-X is a new generation product of high value which has integrated keypad, text
display, single door control and T&A. Its 3 flexible uses are as below.
T&A：TA7002P-X can directly communicate with host PC via RS485 or
TCP/IP which managed by software AccessWatch3000.
Single Door Controller：TA7002P-X can work as a access controller with
external readers for single door In/Out control.
Wiegand Reader With OLED Display：TA7002P-X can work as a reader
which outputs wiegand26 or wiegand34 signal while the OLED screen shows
time and card number.
2. 1 Rex Button output, 1 magnetic input, 1 Wiegand 26/34 input/output(both IC, ID card
compatible, IC card reads serial number), 2 auxiliary inputs, 2 relay outputs, 1 RS485
interface, 1 door bell interface.
3. Can connect with external Wiegand26/34 reader（keypad reader included）， Entrance/exit
can be controlled by “Card/PIN”or “Card + PIN”.
4. Customized OLED LOGO display, English menu with backlight. Showing the name and
card number when reading a card.
5. Network (127 for RS485, no limit for TCP/IP), offline mode available but customers
need to configure via the keypad before work offline.
6. The system can register 100 pcs Wiegand26/34 RFID cards and store 200000 events
when it's offline mode. When it comes to online mode, all data can be uploaded to host
PC and 30000 cards can be registered.
7. 8 sorts of alarm clock for 9 to 5.
8. System can assign different time groups for 124 user departments within 365 days. Each
door can be authorized with 31 time groups, 7 holiday groups. Any days of a year can be
the composition of a holiday group. Anyone who has no access authority of holiday
group will not be entrance allowed. The system will inform all controllers to adjust time
schedule if the date in the 2 temporary time group triggered. The system will
automatically sync the clock to ensure accurate event alert.
9. Remote door control available, multiple incidents alarm functions, exp as door open
timeout, door close timeout, intrusion alarm, duress alarm, tamper alarm and fire alarm.

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 5 of 28
10. Specifications
Work Mode：
Card Mode；
PIN Mode；
Card/PIN Mode；
Card + PIN(interval time 8 sec)
Supported User Number：30000 pcs
PIN User Number：10
Communicate Frequency：
125KHZ:
E: EM；
13.56MHZ:
M: Mifare；
U：CPU
Read Range：3-15CM
Outputs：NC/NO，30VDC，5A
Power Supply：12VDC+10% ，200MA
Dimension：117mm (H) x 86mm (W) x 22mm (D)
1.3 Application Mode
3 Application Modes：
Standalone
Outdoor external reader, indoor TA7002P-X

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 6 of 28
Indoor external reader, outdoor TA7002P-X
Indoor
TA7003N
T
Outdoor
reader
Indoor
Reader
Outdoor
TA7003NT

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 7 of 28
Chapter2 Wiring Diagram
2.1 TA7002P-X Appearance
Figure 2-1
LED:
Blue LED：Power indicator
Green LED：Sensor indicator（Relay turned on indicator）
Keypad:
NO.
Key
Description
NO.
Key
Description
1
1
Numeral 1
7
7
Numeral 7
2
2
Numeral 2
8
8
Numeral 8
3
3
Numeral 3
9
9
Numeral 9
4
4
Numeral 4
10
0
Numeral 0
5
5
Numeral 5
1
*
Cancel / Start
6
6
Numeral 6
12
#
Enter / Confirm
LED (Green&Blue)
Backlight
Keypad
Door bell
Clock
Company Logo

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 8 of 28
2.2 Wiring Diagram
Figure 2-2 Backside
J3：TCP/IP interface
J2：Reader_In & REX
J1：Power & RS485

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 9 of 28
Icon
Mark
Description
Feature
Remark
J1
+12V_In
Power Supply, In
Power supply
GND
Ground, GND
485+
RS485+
RS485 interface
485-
RS485-
+12V_Out
Power Out
Power Out during POE
≦500mA
J2-U
NO1
Normal Open
Lock Relay
COM1
Common
NC1
Normal Closed
NO2
Normal Open
Aux Relay
COM2
Common
NC2
Normal Closed
In1
Input 1
Aux Input
In2
Input 2
GND
Ground, GND
J2-D
BUZ
Buzzer Control
External reader interface
GND
GND, Ground
D1
Data 1
D0
Data 0
LED
LED Control
+12V
+12V, Power Supply
REX
Exit Button
Door Control
SEN
Door Sensor
GND
GND, Ground
J3
J3
TCP/IP, POE
Power Over Ethernet, up to
1000mA
2-1
2.3 Lock Wiring Diagram
J4: Relay Output（Lock Control）
As shown below.
Figure 2-4 Electronic Strike Lock

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 10 of 28
Figure 2-5 Magnetic Lock（Fail safe）
Figure 2-6 Cathode lock（Fail secure）
2.4 RS485 Net Bus
TA7002P-X can communicate via half-duplex RS485 bus, up to 1200m communication distance. Terminals
use series connection.
Please make sure power supply is in off state before do wiring. This helps to avoid any damage maybe caused
to the device.
Figure 2-7
Twisted-pair：Twisted-pair are used to connect controller to controller. No GND is needed.
Series connection：Terminals are connecting via series connection. A multi-bus RS485HUB is
needed if customer needs parallel connection.
RS485 Single Point Ground：If controller transmission line is with shielding or needs ground
line, then all controllers’transmission line can be grounded in either controller. Please
note do not gather all metal side to the GND of controller.
Terminal Resistance：Series connected at the end of the circuit.
120Ω

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 11 of 28
2.5 TCP/IP Network
TA7002P-X TCP/IP network
Figure 2-8
TCP/IP crystal head
Figure 2-9
Sheet 2-2
Normal net cable（to switch）
RJ45 NO.
Difination
1
TX+
2
TX-
3
RX+
6
RX-
8←1
8←1

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 12 of 28
图2-10
Crossed cable（to PC）
Figure 2-11
8←1
8←1
8←1

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 13 of 28
Chapter3 Instructions
User Management、PIN management、Work mode and Time set are configured in the manage menu. Menu
structure is shown below.
Press * 39 # to enter manage menu when idle. In the main menu, “*”works as “cancel”, “#”works as
“confirm”, “3”works as “Up”, ”9”works as “down”.

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 14 of 28
3.1 Clock Configuration
3.1.1 Edit Time
1．Press * 39 # to enter manage menu when idle. In the main menu, “*”works as “cancel”, “#”
works as “confirm”, “3”works as “Up”, ”9”works as “down”.
2．Press “#”to edit time.
3．Use keypad to set the current time, press “#”to confirm.
Time format：Year-Month-Day Hour：Minute
3.1. 2 EditAlarm
1．Press * 39 # to enter manage menu when idle.
2. Press # to enter Clock menu, press 9 to select edit alarm.
2. Press # to enter edit alarm.
Clock ◆
Cards
System
Delete
Edit time ◆
Edit alarm
◆
Edit time
**-**-** **：**
Edit time ◆
Edit alarm
Clock ◆
Cards
System
Delete

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 15 of 28
Press # to select a alarm to be edited. Use keypad to enter the alarm details.
3.2 Card Configuration
3.2. 1Add Card
1．Use button 3 or 9 to select Cards when enter the manage menu.
2. Use button 3 or 9 to selectAdd Card.
3. Press # to enter register interface.
4. Input a ten digits number or flash the card you want to register on TA7002P-X, the card number
will be read by TA7002P-X automatically and shows up on the screen.
5. Press # to enter the next menu.
Verify the card information and input the password if needed then select “Confirm?” and
press# to confirm. If customer wants to add another or more cards, please go back to step 3 and
repeat the process.
Input or Flash
0123456789
Clock
Cards ◆
System
Delete
Card 0000000000 ◆
Password 0000
Disp Mess 00
Confirm？
Input or Flash
0000000000
Add Card ◆
Del Card
Del All Card
Alarm1x ◆
Alarm2x
……
Alarm8x
闹钟 8x

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 16 of 28
3.2. 2 Delete Card
1. Use button 3 or 9 to select Cards when enter the manage menu.
2. Use button 3 or 9 to select Del Card.
3. Press # to enter delete card interface.
4. Input a ten digits number or flash the card you want to register on TA7002P-X, the card number
will be read by TA7002P-X automatically and shows up on the screen.
5. Press # to enter the next menu.
Note：When the screen shows Del Card OK, it means you have successfully deleted a registered card. If
customer wants to delete more cards, just continue flashing card and press # to confirm
deleting. There is no need to go back to step 2.
3.2.3 DelAll Cards
Use Del All Cards to clear all cards.
1. Use button 3 or 9 to select Cards when enter the manage menu.
Del Card？
Input or Flash
0123456789
Input or Flash
0000000000
Add Card
Del Card ◆
Del All Card
Clock
Cards ◆
System
Delete

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 17 of 28
2. Use button 3 or 9 to select Del All Card
3. Press # to enter Delete All Card interface.
4. Input a ten digits number or flash the card you want to register on TA7002P-X, the card number
will be read by TA7002P-X automatically and shows up on the screen.
5. Press # to enter the next menu.
3.3 System Configuration
3.3.1 Language Setting
TA7002P-X support two languages. (English and Chinese)
1. Use button 3 or 9 to select System when enter the manage menu.
2. Press # to enter System interface.
3. Press # to enter language setting interface.
Clock
Cards
System ◆
Delete
Input or Flash
0123456789
Input or Flash
0000000000
Add Card
Del Card
Del All Card ◆
Clock
Cards ◆
System
Delete
Language ◆
Menu Password
Reader Settings
System Info

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 18 of 28
Use button 3 or 9 to select the language customer wanted. Press # to confirm.
3.3.2 Menu Password
There is no defaulted password, customer can set favored password. Steps:
1．Use button 3 or 9 to select System when enter the manage menu.
2. Use button 3 or 9 to select Menu Password.
3. Press # to enter Menu Password setting interface
Use the keypad to input 6 digits password and press # to confirm. User will have to input the
password if he wants to enter manage menu.
3.3.3 Reader Settings
1. Use button 3 or 9 to select System when enter the manage menu.
2. Use button 3 or 9 to select Reader Settings.
Clock
Cards
System ◆
Delete
Language
Menu Password ◆
Reader Settings
System Info
Clock
Cards
System ◆
Delete
New Password
——————
English×◆
Chinese√

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 19 of 28
3. Press # to enter Reader setting interface
Use button 3 or 9 to select reader Input/output format。
3.3.4 System Info Configuration
3.3.4.1 Device ID
1. Use button 3 or 9 to select System when enter the manage menu.
2. Use button 3 or 9 to select System Info.
3. Press # to enter System Info setting interface
4. Use button 3 or 9 to select Device ID and press # to confirm.
Press # to confirm Device ID setting. Device ID must be set when using multiple TA7002P-X
while it’s not necessary for standalone.
Language
Menu Password
Reader Settings
System Info ◆
◆
Clock
Cards
System ◆
Delete
WG26 IN√◆
WG34 IN×
WG26 OUT×
WG26 OUT×
Language
Menu Password
Reader Settings ◆
System Info
Device ID
001
Device ID ◆
Network
Sleep Time
Board Info

KEYKING GROUP TA7002P-* User Manual（V1.0）
Page 20 of 28
3.3.4.2 Network Configuration
1. Use button 3 or 9 to select System when enter the manage menu.
2. Use button 3 or 9 to select System Info.
3. Press # to enter System Info setting interface
4. Use button 3 or 9 to select Network and press # to confirm.
Use button 3 or 9 to select network mode. The defaulted IP address is 10.1.1.10
3.3.4.3 Sleep Time
1. Use button 3 or 9 to select System when enter the manage menu.
2. Use button 3 or 9 to select System Info.
3. Press # to enter System Info setting interface.
Device ID
Network
Sleep Time ◆
Board Info
Language
Menu Password
Reader Settings
System Info ◆
Clock
Cards
System ◆
Delete
Device ID
Network ◆
Sleep Time
Board Info
Language
Menu Password
Reader Settings
System Info ◆
Clock
Cards
System ◆
Delete
Unlock√◆
Locked×
Special×