Keysight E5867A User manual

Installation
Guide
Keysight E5867A
Removable Hard Drive
SSD for 16860-Series
Logic Analyzers

Notices
© Keysight Technologies 2016
No part of this manual may be reproduced
in any form or by any means (including
electronic storage and retrieval or transla-
tion into a foreign language) without prior
agreement and written consent from
Keysight Technologies as governed by
United States and international copyright
laws.
Manual Part Number
E5867-97001
Edition
First Edition, August 2016
Printed in Malaysia
Published By:
Keysight Technologies
Plot No. CP-11, Sector- 8,
IMT Manesar, Gurgaon - 122051, India
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED "AS IS," AND IS
SUBJECT TO BEING CHANGED, WITHOUT
NOTICE, IN FUTURE EDITIONS. FURTHER,
TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, KEYSIGHT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR
IMPLIED WITH REGARD TO THIS MANUAL
AND ANY INFORMATION CONTAINED
HEREIN, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. KEYSIGHT SHALL
NOT BE LIABLE FOR ERRORS OR FOR
INCIDENTAL OR CONSEQUENTIAL
DAMAGES IN CONNECTION WITH THE
FURNISHING, USE, OR PERFORMANCE OF
THIS DOCUMENT OR ANY INFORMATION
CONTAINED HEREIN. SHOULD KEYSIGHT
AND THE USER HAVE A SEPARATE
WRITTEN AGREEMENT WITH WARRANTY
TERMS COVERING THE MATERIAL IN THIS
DOCUMENT THAT CONFLICT WITH THESE
TERMS, THE WARRANTY TERMS IN THE
SEPARATE AGREEMENT WILL CONTROL.
Technology Licenses
The hardware and/or software described in
this document are furnished under a
license and may be used or copied only in
accordance with the terms of such license.
U.S. Government Rights
The Software is "commercial computer
software," as defined by Federal Acquisition
Regulation ("FAR") 2.101. Pursuant to FAR
12.212 and 27.405-3 and Department of
Defense FAR Supplement ("DFARS")
227.7202, the U.S. government acquires
commercial computer software under the
same terms by which the software is cus-
tomarily provided to the public. Accord-
ingly, Keysight provides the Software to
U.S. government customers under its stan-
dard commercial license, which is embod-
ied in its End User License Agreement
(EULA), a copy of which can be found at
http://www.key-
sight.com/find/sweula. The license set
forth in the EULA represents the exclusive
authority by which the U.S. government
may use, modify, distribute, or disclose the
Software. The EULA and the license set
forth therein, does not require or permit,
among other things, that Keysight: (1) Fur-
nish technical information related to com-
mercial computer software or commercial
computer software documentation that is
not customarily provided to the public; or
(2) Relinquish to, or otherwise provide, the
government rights in excess of these rights
customarily provided to the public to use,
modify, reproduce, release, perform, dis-
play, or disclose commercial computer
software or commercial computer software
documentation. No additional government
requirements beyond those set forth in the
EULA shall apply, except to the extent that
those terms, rights, or licenses are explic-
itly required from all providers of commer-
cial computer software pursuant to the FAR
and the DFARS and are set forth specifically
in writing elsewhere in the EULA. Keysight
shall be under no obligation to update,
revise or otherwise modify the Software.
With respect to any technical data as
defined by FAR 2.101, pursuant to FAR
12.211 and 27.404.2 and DFARS 227.7102,
the U.S. government acquires no greater
than Limited Rights as defined in FAR
27.401 or DFAR 227.7103-5 (c), as appli-
cable in any technical data. 52.227-14
(June 1987) or DFAR 252.227-7015 (b)(2)
(November 1995), as applicable in any
technical data.
Safety Notices
CAUTION
A CAUTION notice denotes a hazard.
It calls attention to an operating pro-
cedure, practice, or the like that, if
not correctly performed or adhered
to, could result in damage to the
product or loss of important data. Do
not proceed beyond a CAUTION
notice until the indicated conditions
are fully understood and met.
WARNING
A WARNING notice denotes a hazard.
It calls attention to an operating pro-
cedure, practice, or the like that, if
not correctly performed or adhered
to, could result in personal injury or
death. Do not proceed beyond a
WARNING notice until the indicated
conditions are fully understood and
met.
2 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 3
Safety Summary
The following general safety precautions must be observed during all phases of operation
of this instrument. Failure to comply with these precautions or with specific warnings or
operating instructions in the product manuals violates safety standards of design,
manufacture, and intended use of the instrument. Keysight Technologies assumes no
liability for the customer's failure to comply with these requirements. Product manuals
are provided with your instrument on CD-ROM and/or in printed form. Printed manuals
are an option for many products. Manuals may also be available on the Web. Go to
www.keysight.com and type in your product number in the Search field at the top of the
page.
General Do not use this product in any manner not specified by the manufacturer. The protective
features of this product may be impaired if it is used in a manner not specified in the
operation instructions.
Before Applying Power Verify that all safety precautions are taken. Make all connections to the unit before
applying power. Note the instrument's external markings described in “Safety Symbols”.
Ground the Instrument If your product is provided with a grounding type power plug, the instrument chassis and
cover must be connected to an electrical ground to minimize shock hazard. The ground
pin must be firmly connected to an electrical ground (safety ground) terminal at the
power outlet. Any interruption of the protective (grounding) conductor or disconnection
of the protective earth terminal will cause a potential shock hazard that could result in
personal injury.
Fuses See the user's guide or operator's manual for information about line-fuse replacement.
Some instruments contain an internal fuse, which is not user accessible.
Do Not Operate in an
Explosive Atmosphere
Do not operate the instrument in the presence of flammable gases or fumes.
Do Not Remove the
Instrument Cover
Only qualified, service-trained personnel who are aware of the hazards involved should
remove instrument covers. Always disconnect the power cable and any external circuits
before removing the instrument cover.
Cleaning Clean the outside of the instrument with a soft, lint-free, slightly dampened cloth. Do not
use detergent or chemical solvents.
Do Not Modify the
Instrument
Do not install substitute parts or perform any unauthorized modification to the product.
Return the product to an Keysight Sales and Service Office for service and repair to
ensure that safety features are maintained.
In Case of Damage Instruments that appear damaged or defective should be made inoperative and secured
against unintended operation until they can be repaired by qualified service personnel.

4 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
Safety Symbols
Table 1 Safety Symbol
CAUTION
A CAUTION notice denotes a hazard. It calls attention to an operating procedure,
practice, or the like that, if not correctly performed or adhered to, could result in
damage to the product or loss of important data. Do not proceed beyond a CAUTION
notice until the indicated conditions are fully understood and met.
WARNING
A WARNING notice denotes a hazard. It calls attention to an operating procedure,
practice, or the like that, if not correctly performed or adhered to, could result in
personal injury or death. Do not proceed beyond a WARNING notice until the
indicated cond itions are fully understood and met.
Symbol Description
Direct current
Alternating current
Both direct and alternating current
Three phase alternating current
Three phase alternating current
Earth ground terminal
Protective earth ground terminal
Frame or chassis ground terminal
Terminal is at earth potential

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 5
Equipotentiality
N Neutral conductor on permanently
installed equipment
L Line conductor on permanently installed
equipment
On (mains supply)
Off (mains supply)
Standby (mains supply). The instrument is
not completely disconnected from the
mains supply when the power switch is in
the standby position
In position of a bi-stable push switch
Out position of a bi-stable push switch
Equipment protected throughout by
DOUBLE INSULATION or REINFORCED
INSULATION
Caution, refer to accompanying
documentation
Caution, risk of electric shock
Do not apply around or remove from
HAZARDOUS LIVE conductors
Application around and removal from
HAZARDOUS LIVE conductors is
permitted
Caution, hot surface
Symbol Description

6 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
Ionizing radiation
CAT I IEC Measurement Category I
CAT II Measurement Category II
CAT III Measurement Category III
CAT IV Measurement Category IV
Symbol Description

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 7
Compliance and Environmental Information
Table 2 Compliance and Environmental Information
Safety Symbol Description
CSA is the Canadian certification mark to demonstrate compliance with the Safety
requirements.
The C-tick mark is a registered trademark of the Spectrum Management
Agency of Australia. This signifies compliance with the Australia EMC
Framework regulations under the terms of the Radio Communication Act
of 1992.
CE compliance marking to the EU Safety and EMC Directives.
ISM GRP-1A classification according to the international EMC standard.
ICES/NMB-001 compliance marking to the Canadian EMC standard.

8 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 9
Contents
1 Handling the Removable Hard Drive SSD
Protecting Against Electrostatic Discharge (ESD) 11
Protecting Against Contamination of the Edge Connector 11
Protecting Against Physical Shock 12
2 Installing the Hard Drive
Step 1. Back up data for transfer to new hard drive SSD 14
Step 2. Power OFF the 16860 logic analyzer 14
Using the Windows Shutdown 15
Using a Short Press of the Power Button 15
Using a Long Press of the Power Button 15
Unplugging the Power Cord or Power Loss 16
Step 3. Remove the current hard drive SSD 16
Step 4. Install the new hard drive 17
Step 5. Power on the 16860 logic analyzer 19
Step 6. Perform the first-time set up steps 19
Step 7. Perform the first-time set up procedures 19
Step 8. Restore data 19
Step 9. Install any additional application software 19

10 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
Contents

Keysight E5867A Removable Hard Drive SSD for
16860-Series Logic Analyzers
Installation Guide
1Handling the
Removable Hard Drive
SSD
For the integrity of the data on your hard disk drive, Keysight recommends
that you take the following precautions while handling and storing the
hard disk drives:
• Store unused hard disk drives in the shipping container.
• Protect the hard disk drive from electrostatic discharge (ESD).
• Protect the hard disk drive’s edge connectors from physical
contamination.
• Protect the hard disk drive from physical shock.
Protecting Against Electrostatic Discharge (ESD)
Protecting Against Contamination of the Edge Connector
CAUTION
Electrostatic discharge can damage electronic components. Use
grounded wrist straps and mats when handling electronic components.
CAUTION
The hard drive SSD edge connector is sensitive to ESD and mechanical
or material contamination. Take precautions to protect the edge
connector from contamination during handling and storage.

12 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
1 Handling the Removable Hard Drive SSD
Protecting Against Physical Shock
CAUTION
While operating, do not expose the hard disk drive to more than 5 to 500
Hz at 0.3 g rms.

Keysight E5867A Removable Hard Drive SSD for
16860-Series Logic Analyzers
Installation Guide
2Installing the Hard
Drive
Step 1. Back up data for transfer to new hard drive SSD / 14
Step 2. Power OFF the 16860 logic analyzer / 14
Step 3. Remove the current hard drive SSD / 16
Step 4. Install the new hard drive / 17
Step 5. Power on the 16860 logic analyzer / 19
Step 6. Perform the first-time set up steps / 19
Step 7. Perform the first-time set up procedures / 19
Step 8. Restore data / 19
Step 9. Install any additional application software / 19
CAUTION
Electrostatic discharge can damage electronic components. Use
grounded wrist straps and mats when handling electronic components.

14 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
2 Installing the Hard Drive
Step 1. Back up data for transfer to new hard drive SSD
1ClosetheKeysight Logic and Protocol Analyzer application software.
2 Back up any data and server license files you want to retain using LAN,
USB flash drive, writable CDs, etc.
Keysight recommends floating licenses for logic analyzers with
removable disks (such as the 16860-series logic analyzers).
If the license server is on the logic analyzer, back up the server license
files which are located in the “LicenseFiles” folder under the license
server’s installation directory. For example, the default location is: C:\
Program Files\Agilent Technologies\LicenseServer\LicenseFiles\
License files have the extension “.lic”.
You can also use node-locked licenses. However, because the logic
analyzer host ID changes with the hard disk drive, you must have
separate licenses on each disk. Node-locked license files are located in
the “License” folder under the Keysight Logic and Protocol Analyzer
application’s installation directory. For example, the default location is:
C:\Program Files\Agilent Technologies\Logic Analyzer\License\
Step 2. Power OFF the 16860 logic analyzer
1 Power off the system using one of the methods explained below.
2 Remove the power cord.
WARNING
Hazardous voltages exist on the power supply. To avoid electrical shock,
disconnect the power from the instrument before performing the
following procedures. After disconnecting the power, wait at least six
minutes for the capacitors on the power supply board to discharge
before servicing the instrument.
CAUTION
Damage can occur to electronic components if you remove or replace
assemblies when the instrument is on or when the power cable is
connected. Never attempt to remove or install any assembly with the
instrument on or with the power cable connected.

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 15
Installing the Hard Drive 2
Using the Windows Shutdown
On the logic analysis system desktop, click Start > Shut Down or if you are
running remote desktop, click Start > Settings > Windows Security > Shut
Down. This software power off does the following:
• Closes all programs that are running.
• Writes all data to the disk.
• Turns off the power supply.
• If the system is unplugged while it is off and then plugged back in, the
system will not power on until the power button is pressed.
Using a Short Press of the Power Button
Pressing the power button on a frame for a short time (less than 2
seconds):
• Closes all programs that are running.
• Writes all data to the disk.
• Turns off the power supply.
If the power button is depressed for a short time (less than 2 seconds or
so) while another instrument has an open Remote Desktop connection to
this instrument, a message on the logic analysis system screen (not on the
remote desktop) will pop up asking if you really want to power down.
Clicking the 'yes' button results in the above events. Clicking 'no' will
prevent the shutdown and not answering the dialog box (neither clicking
"Yes" or "No") will have no effect. Further short presses on the power
button will have no effect.
Using a Long Press of the Power Button
Pressing the power button for more than 4 seconds will power the system
down abruptly. Use this method only when other methods have not
responded:
• Programs that are running will not be shut down. Any data that has not
been written to the disk will be lost.
• Turns off the power supply.
• If the system is unplugged while it is off and then plugged back in, the
system will not power on until the power button is pressed.
• If the system does not boot, the hard disk drive will need to be
re-imaged.

16 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
2 Installing the Hard Drive
Unplugging the Power Cord or Power Loss
Unplugging power while the instrument is turned on or a power loss is
similar to the long press of the power button with one exception:
• When the system is plugged back in, it will power up and boot into
Windows.
Step 3. Remove the current hard drive SSD
The 16860 logic analyzer has a removable hard disk drive SSD. It can be
removed and replaced without disassembling the instrument.
1 Loosen both the thumb screws that hold the hard disk drive in place.
Thumb Screws
Removable Hard
Disk Drive SSD

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 17
Installing the Hard Drive 2
2 Pull the drive tray out to remove the disk drive.
Step 4. Install the new hard drive
1 Slide the new removable hard drive SSD into the drive bay.
2 Gently press the tray all the way in to seat the disk drive connectors.
3 Tighten both the thumb screws that hold the hard disk drive in place.
Removable Hard Disk
Drive SSD pulled out

18 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
2 Installing the Hard Drive

Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide 19
Installing the Hard Drive 2
Step 5. Power on the 16860 logic analyzer
Turn on the logic analyzer.
Step 6. Perform the first-time set up steps
If you are using the E5867A replacement hard disk as an additional
bootable drive, the replacement disk is pre-configured with the operating
system, frame drivers, and logic and protocol analysis application software
(just like the original 16860 disk as shipped from the factory). The next step
is to perform the first-time set up procedures described in the 16860
-Series Logic Analyzers Installation Guide shipped with the 16860 logic
analyzer.
Step 7. Perform the first-time set up procedures
The next step is to perform the first-time set up procedures described in
the 16860-Series Logic Analyzer Installation Guide shipped with the
16860 logic analyzer.
Step 8. Restore data
Restore the data and server license files you backed up in “Step 1. Back up
data for transfer to new hard drive SSD" on page 14.
Step 9. Install any additional application software
Install any additional application software.

20 Keysight E5867A Removable Hard Drive SSD for 16860-Series Logic Analyzers Installation Guide
2 Installing the Hard Drive