Keysight M9099 User guide

Startup
Guide
Keysight M9099
Waveform Creator 3.2
Notice:This document contains references to Agilent. Please note that Agilent's Test
and Measurement business has become Keysight Technologies. For more information,
go to www.keysight.com.

Notices
Copyright Notice
© Keysight Technologies 2013 - 2016
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a foreign
language) without prior agreement and
written consent from Keysight
Technologies, Inc. as governed by
United States and international
copyright laws.
Manual Part Number
M9099-90002
Published By
Keysight Technologies
Ground Floor and Second Floor, CP-11
Sector-8, IMT Manesar – 122051
Gurgaon, Haryana, India
Edition
Edition 3.2, November, 2016
Regulatory Compliance
This product has been designed and
tested in accordance with accepted
industry standards, and has been
supplied in a safe condition. To review
the Declaration of Conformity, go to
http://www.keysight.com/go/conformity.
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED “AS IS,” AND
IS SUBJECT TO BEING CHANGED,
WITHOUT NOTICE, IN FUTURE
EDITIONS. FURTHER, TO THE
MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, KEYSIGHT
DISCLAIMS ALL WARRANTIES, EITHER
EXPRESS OR IMPLIED, WITH REGARD
TO THIS MANUAL AND ANY
INFORMATION CONTAINED HEREIN,
INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. KEYSIGHT
SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE
FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT
OR OF ANY INFORMATION CONTAINED
HEREIN. SHOULD KEYSIGHT AND THE
USER HAVE A SEPARATE WRITTEN
AGREEMENT WITH WARRANTY TERMS
COVERING THE MATERIAL IN THIS
DOCUMENT THAT CONFLICT WITH
THESE TERMS, THE WARRANTY
TERMS IN THE SEPARATE
AGREEMENT SHALL CONTROL.
KEYSIGHT TECHNOLOGIES DOES NOT
WARRANT THIRD-PARTY SYSTEM-
LEVEL (COMBINATION OF CHASSIS,
CONTROLLERS, MODULES, ETC.)
PERFORMANCE, SAFETY, OR
REGULATORY COMPLIANCE, UNLESS
SPECIFICALLY STATED.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance with
the terms of such license.
U.S. Government Rights
The Software is “commercial computer
software,” as defined by Federal
Acquisition Regulation (“FAR”) 2.101.
Pursuant to FAR 12.212 and 27.405-3
and Department of Defense FAR
Supplement (“DFARS”) 227.7202, the
U.S. government acquires commercial
computer software under the same
terms by which the software is
customarily provided to the public.
Accordingly, Keysight provides the
Software to U.S. government customers
under its standard commercial license,
which is embodied in its End User
License Agreement (EULA), a copy of
which can be found at
http://www.keysight.com/find/sweula. The
license set forth in the EULA represents
the exclusive authority by which the
U.S. government may use, modify,
distribute, or disclose the Software. The
EULA and the license set forth therein,
does not require or permit, among other
things, that Keysight: (1) Furnish
technical information related to
commercial computer software or
commercial computer software
documentation that is not customarily
provided to the public; or (2) Relinquish
to, or otherwise provide, the
government rights in excess of these
rights customarily provided to the
public to use, modify, reproduce,
release, perform, display, or disclose
commercial computer software or
commercial computer software
documentation. No additional
government requirements beyond
those set forth in the EULA shall apply,
except to the extent that those terms,
rights, or licenses are explicitly required
from all providers of commercial
computer software pursuant to the FAR
and the DFARS and are set forth
specifically in writing elsewhere in the
EULA. Keysight shall be under no
obligation to update, revise or otherwise
modify the Software. With respect to
any technical data as defined by FAR
2.101, pursuant to FAR 12.211 and
27.404.2 and DFARS 227.7102, the U.S.
government acquires no greater than
Limited Rights as defined in FAR 27.401
or DFAR 227.7103-5 (c), as applicable in
any technical data.
Safety Notices
A CAUTION notice denotes a hazard. It
calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in damage to the product
or loss of important data. Do not
proceed beyond a CAUTION notice until
the indicated conditions are fully
understood and met.
A WARNING notice denotes a hazard. It
calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in personal injury or death.
Do not proceed beyond a WARNING
notice until the indicated conditions are
fully understood and met.
The following safety precautions should
be observed before using this product
and any associated instrumentation.
This product is intended for use by
qualified personnel who recognize
shock hazards and are familiar with the
safety precautions required to avoid
possible injury. Read and follow all
iii

installation, operation, and
maintenance information carefully
before using the product.
If this product is not used as specified,
the protection provided by the
equipment could be impaired. This
product must be used in a normal
condition (in which all means for
protection are intact) only.
The types of product users are:
Responsible body is the individual or
group responsible for the use and main-
tenance of equipment, for ensuring that
the equipment is operated within its spe-
cifications and operating limits, and for
ensuring operators are adequately trained.
Operators use the product for its intended
function. They must be trained in electrical
safety procedures and proper use of the
instrument. They must be protected from
electric shock and contact with hazardous
live circuits.
Maintenance personnel perform routine
procedures on the product to keep it oper-
ating properly (for example, setting the line
voltage or replacing consumable mater-
ials). Maintenance procedures are
described in the user documentation. The
procedures explicitly state if the operator
may perform them. Otherwise, they should
be performed only by service personnel.
Service personnel are trained to work on
live circuits, perform safe installations, and
repair products. Only properly trained ser-
vice personnel may perform installation
and service procedures.
Operator is responsible to maintain safe
operating conditions. To ensure safe
operating conditions, modules should
not be operated beyond the full
temperature range specified in the
Environmental and physical
specification. Exceeding safe operating
conditions can result in shorter
lifespans, improper module
performance and user safety issues.
When the modules are in use and
operation within the specified full
temperature range is not maintained,
module surface temperatures may
exceed safe handling conditions which
can cause discomfort or burns if
touched. In the event of a module
exceeding the full temperature range,
always allow the module to cool before
touching or removing modules from
chassis.
Keysight products are designed for use
with electrical signals that are rated
Measurement Category I and
Measurement Category II, as described
in the International Electrotechnical
Commission (IEC) Standard IEC 60664.
Most measurement, control, and data
I/O signals are Measurement Category I
and must not be directly connected to
mains voltage or to voltage sources with
high transient over-voltages.
Measurement Category II connections
require protection for high transient
over-voltages often associated with
local AC mains connections. Assume all
measurement, control, and data I/O
connections are for connection to
Category I sources unless otherwise
marked or described in the user
documentation.
Exercise extreme caution when a shock
hazard is present. Lethal voltage may
be present on cable connector jacks or
test fixtures. The American National
Standards Institute (ANSI) states that a
shock hazard exists when voltage levels
greater than 30V RMS, 42.4V peak, or
60VDC are present. A good safety
practice is to expect that hazardous
voltage is present in any unknown
circuit before measuring.
Operators of this product must be
protected from electric shock at all
times. The responsible body must
ensure that operators are prevented
access and/or insulated from every
connection point. In some cases,
connections must be exposed to
potential human contact. Product
operators in these circumstances must
be trained to protect themselves from
the risk of electric shock. If the circuit is
capable of operating at or above 1000V,
no conductive part of the circuit may be
exposed.
Do not connect switching cards directly
to unlimited power circuits. They are
intended to be used with impedance-
limited sources. NEVER connect
switching cards directly to AC mains.
When connecting sources to switching
cards, install protective devices to limit
fault current and voltage to the card.
Before operating an instrument, ensure
that the line cord is connected to a
properly-grounded power receptacle.
Inspect the connecting cables, test
leads, and jumpers for possible wear,
cracks, or breaks before each use.
When installing equipment where
access to the main power cord is
restricted, such as rack mounting, a
separate main input power disconnect
device must be provided in close
proximity to the equipment and within
easy reach of the operator.
For maximum safety, do not touch the
product, test cables, or any other
instruments while power is applied to
the circuit under test. ALWAYS remove
power from the entire test system and
discharge any capacitors before:
connecting or disconnecting cables or
jumpers, installing or removing
switching cards, or making internal
changes, such as installing or removing
jumpers.
Do not touch any object that could
provide a current path to the common
side of the circuit under test or power
line (earth) ground. Always make
measurements with dry hands while
standing on a dry, insulated surface
capable of withstanding the voltage
being measured.
The instrument and accessories must
be used in accordance with its
specifications and operating
instructions, or the safety of the
equipment may be impaired.
Do not exceed the maximum signal
levels of the instruments and
accessories, as defined in the
specifications and operating
information, and as shown on the
instrument or test fixture panels, or
switching card.
When fuses are used in a product,
replace with the same type and rating
for continued protection against fire
hazard.
Chassis connections must only be used
as shield connections for measuring
iv

circuits, NOT as safety earth ground
connections.
If you are using a test fixture, keep the
lid closed while power is applied to the
device under test. Safe operation
requires the use of a lid interlock.
Instrumentation and accessories shall
not be connected to humans.
Before performing any maintenance,
disconnect the line cord and all test
cables.
To maintain protection from electric
shock and fire, replacement
components in mains circuits –
including the power transformer, test
leads, and input jacks – must be
purchased from Keysight. Standard
fuses with applicable national safety
approvals may be used if the rating and
type are the same. Other components
that are not safety-related may be
purchased from other suppliers as long
as they are equivalent to the original
component (note that selected parts
should be purchased only through
Keysight to maintain accuracy and
functionality of the product). If you are
unsure about the applicability of a
replacement component, call an
Keysight office for information.
No operator serviceable parts inside.
Refer servicing to qualified personnel.
To prevent electrical shock do not
remove covers. For continued
protection against fire hazard, replace
fuse with same type and rating.
PRODUCT MARKINGS:
The CE mark is a registered trademark
of the European Community.
Australian Communication and Media
Authority mark to indicate regulatory
compliance as a registered supplier.
This symbol indicates product
compliance with the Canadian
Interference-Causing Equipment
Standard (ICES-001). It also identifies
the product is an Industrial Scientific
and Medical Group 1 Class A product
(CISPR 11, Clause 4).
South Korean Class A EMC Declaration.
This equipment is Class A suitable for
professional use and is for use in
electromagnetic environments outside
of the home. A급기기( 업무용 방송통
신기자재 )이 기기는 업무용 (A 급)전 자
파적합기기로서 판 매자 또는 사용자는
이점을주의하시기바라며,가정외의
지역에서 사용하는 것을 목적으 로 합니
다.
This product complies with the WEEE
Directive marketing requirement. The
affixed product label (above) indicates
that you must not discard this
electrical/electronic product in
domestic household waste. Product
Category: With reference to the
equipment types in the WEEE directive
Annex 1, this product is classified as
“Monitoring and Control
instrumentation” product. Do not
dispose in domestic household waste.
To return unwanted products, contact
your local Keysight office, or for more
information see
http://about.keysight.com/en/companyinfo/e
nvironment/takeback.shtml.
This symbol indicates the instrument is
sensitive to electrostatic discharge
(ESD). ESD can damage the highly
sensitive components in your
instrument. ESD damage is most likely
to occur as the module is being
installed or when cables are connected
or disconnected. Protect the circuits
from ESD damage by wearing a
grounding strap that provides a high
resistance path to ground. Alternatively,
ground yourself to discharge any built-
up static charge by touching the outer
shell of any grounded instrument
chassis before touching the port
connectors.
This symbol on an instrument means
caution, risk of danger. You should refer
to the operating instructions located in
the user documentation in all cases
where the symbol is marked on the
instrument.
This symbol indicates the time period
during which no hazardous or toxic
substance elements are expected to
leak or deteriorate during normal use.
Forty years is the expected useful life of
the product.
v

vi

vii
Contents
Preface 8
Introduction 9
Related Documentation 11
System Requirements 13
Summary of Software/Hardware Compatibility with Waveform Creator 13
Installing Waveform Creator 15
Pre-requisites 15
Obtain Waveform Creator Executable 15
Installing Waveform Creator 15
Silent Installation of Waveform Creator 17
Setting Up Licenses 18
Keysight Software Licensing 18
Waveform Creator Licenses 19
Quick Start 21
Configure the System 21
Create a Simple Waveform 21
Download the Waveform 22
M9381A VSG 22
Connect the M9099 Waveform Creator to the M9381A Vector Signal Generator 22
Generate Output 23
Data File Write 23

Preface
Preface
The scope of the Startup Guide is to introduce you to Waveform Creator software and
describe the process of Installing and Licensing the product. It also encloses details
on how to quickly get started with the software.
To access M9099 Waveform Creator help, launch the Product and click Help >User's
Guide.
8 Keysight M9099 Waveform Creator 3.2 Startup Guide

Introduction
Keysight M9099 Waveform Creator 3.2 Startup Guide 9
Introduction
M9099 Waveform Creator provides a modular and flexible waveform creation
environment supporting analog and digital modulation formats for a series of Keysight
instruments for R&D, design validation, and test engineers who need to create and
manage custom waveforms for wireless and high speed wireline product design and
testing.
Waveform Creator provides a simple, easy, and modular SW framework for creating,
combining & managing custom, arbitrary waveforms, with support for corrected
waveform download to Keysight AWGs and Signal Generators. It accelerates design
validation and testing of chips, modules, and systems by streamlining development
and management of custom stimulus waveforms.
Waveform Creator provides various benefits out of the box:
Optional generation of DOCSIS 3.1 downstream and upstream signals.
Optional waveform creation plug-in for basic digital modulation.
Optional waveform creation plug-in for SystemVue simulation models.
Other Standard waveform plug-ins for general-purpose waveform creation.
Importing of waveform data from CSV, LabVIEW CSV, HDF, BIN, M8190A DUC
IQBINFile, or Signal Studio's WFM file type.
Flexible waveform creation and generation capability for the following Keysight
products:

Introduction
M9381A PXI VSG,
N5182A/B MXG, N5172B EXG, and E4438C ESG,
M933xA AWG, N824xA AWG, and
M8195A AWG, M8190A AWG and 81180A/B AWG
335xx and 336xx AWG
Output plug-in for writing unencrypted waveform files (CSV, MAT,BIN,M8190A
DUC IQBIN, M9381A native files, and WFM).
User extendable functionality such as creating your own waveform input plug-
ins.
SCPI remote control for test automation.
10 Keysight M9099 Waveform Creator 3.2 Startup Guide

RelatedDocumentation
Keysight M9099 Waveform Creator 3.2 Startup Guide 11
Related Documentation
To access documentation related to M9099 Waveform Creator, click the links below
to open the related document.
Document Description Help Link/Location Format
Startup
Guide
This guide includes
quick install and
license setup
instructions with
instructions to quickly
get started with
Waveform Creator
64-bit -C:\Program Files
(x86)\Keysight\M9099\Documentation\M9099_
StartupGuide.pdf
Web Link -
http://literature.cdn.keysight.com/litweb/pdf/M9099-
90002.pdf
PDF
M9099
Waveform
Creator
Help
This help includes
Waveform Creator
Core GUI and
supported Plug-ins'
documentation
32-bit -C:\Program Files
(x86)\Keysight\M9099\Documentation\wc.chm
(Microsoft
Help
Format)
CHM
SCPI
Reference
Manual
This manual includes
descriptions and
details of SCPI
commands supported
in Waveform Creator
32-bit -C:\Program Files
(x86)\Keysight\M9099\Documentation\SCPI Command
Reference.html
HTML
Keysight
License
Manager
Help
This help file provides
information on
Keysight Licensing
32-bit -C:\Program Files\Agilent\Agilent License
Manager\AgilentLicenseManager.chm
64-bit -C:\Program Files(x86)\Agilent\Agilent License
Manager\AgilentLicenseManager.chm
Alternatively, you can find help under:Start >All Programs >
Keysight License Manager >Keysight License Manager Help
(Microsoft
Help
Format)
CHM
Keysight
I/O
Libraries
Help
This help file provides
information on
Keysight I/O libraries
32-bit -C:\Program Files\Agilent\I/O Libraries
Suite\VisaCom.chm
64-bit -C:\Program Files(x86)\Agilent\I/O Libraries
Suite\VisaCom.chm
(Microsoft
Help
Format)
CHM
SystemVue
Help
This is online version
of SystemVue
software help
http://www.keysight.com/find/eesof-systemvue-
documentation
Web
For more details, visit:

RelatedDocumentation
Product Documentation on the web: http://www.keysight.com/find/modular-
m9099-docs .
KC for Waveform Creator: http://www.keysight.com/find/modular-wfc-
knowledge .
KC for Modular Solutions: http://www.keysight.com/find/modular-
knowledgecenter .
12 Keysight M9099 Waveform Creator 3.2 Startup Guide

System Requirements
Keysight M9099 Waveform Creator 3.2 Startup Guide 13
System Requirements
Following are Keysight recommended configurations:
CPU 2 GHz or faster 32-bit (x86) or 64-bit (x64) processor
RAM 2 GB recommended (32-bit) / 4 GB recommended (64-bit)
Video RAM 512 MB recommended
Hard Disk 1 GB available
Additional
Drives
DVD to load software; license transfer requires network access, USB Flash
drive, USB hard drive, or USB DVD drive
Operating
System
Microsoft Windows® 7 Professional, Enterprise, or Ultimate (64-bit/32-bit)
Summary of Software/Hardware Compatibility with
Waveform Creator
Microsoft .NET
Framework
Ensure that you have Microsoft .NET Framework version 4 or higher installed
on your system. The Microsoft .NET Framework 4 can be found at
http://www.microsoft.com/en-in/download/details.aspx?id=17851 .
Keysight IO
Libraries Suite
Ensure that you have IO Libraries Suite 16.3 or higher installed on your
system. The Keysight IO Libraries Suite can be found on the CD that is part of
shipment content or at http://www.keysight.com/find/iosuite .
VSA for pre-
corrections
filter
calibration
If you wish to use the optional pre-corrections filter calibration capability, you
also need Keysight 89601B VSA version 15 or higher installed on your
system. Support till version 18.5 is provided.
M9381A
VSG/CW
Source
Instrument
Drivers
Install M9381A VSG Drivers from http://www.keysight.com/find/M9381A
Install M9381A driver version 1.3.300.0 or higher.
M8190A AWG
Driver
If you wish to use the M8190A streaming capability, you also need Keysight
M8190A Driver. Install the M8190A driver from
http://www.keysight.com/main/software.jspx?ckey=sw385
Install version 3.0 or higher.
NI-IVI
Compliance
Package
The M933xA series AWG require that the NI IVI Compliance Package 4.1 or
greater be installed. To get the latest release of the NI IVI Compliance
Package, go to http://www.ni.com/drivers/

System Requirements
M933xA AWG
Source
Instrument
Drivers
Install M933xA Drivers from
http://www.keysight.com/main/software.jspx?ckey=2033326
Install M933xA driver version 2.01 or higher.
N824xA AWG
Source
Instrument
Drivers
If you want to use N824xA output plug-in, install N824xA AWG Source
Instrument Driver version 1.31.3 from
http://www.keysight.com/main/software.jspx?ckey=1670471 .
SystemVue
Software
To use SystemVue Model Plug-in, install SystemVue software 2013.08 or
2013.08 SP1 release.
14 Keysight M9099 Waveform Creator 3.2 Startup Guide

Installing WaveformCreator
Keysight M9099 Waveform Creator 3.2 Startup Guide 15
Installing Waveform Creator
Follow the given steps to get the executable and install Keysight M9099 Waveform
Creator software (core and plug-ins) on your system.
Pre-requisites
A host PC with Keysight IO Libraries Suite software correctly installed.
For more details, refer to Summary of Software/Hardware Compatibility with
Waveform Creator section under System Requirements .
Obtain Waveform Creator Executable
Obtain the Waveform Creator executable from the following sources:
www.keysight.com/find/M9099-SW
CD-ROM (Product ordered with -MED option)
Installing Waveform Creator
The installer for Waveform Creator supports smooth upgrade from
previous version. You don't need to uninstall previous version of
Waveform Creator (core and plug-ins) from your computer. This is
automatically done of by the Waveform Creator installer.
Perform the following steps to install Waveform Creator:
1. Double-click the executable (Keysight_M9099_3-2_Setup.exe) to run the
Waveform Creator setup. The following screen appears:

Installing WaveformCreator
2. Follow the guided tour.
3. Select the features (plug-ins) you want to install and click Next to install in the
default folder.
4. Follow the guided tour to complete the installation.
If you do not have the Keysight M938x Instrument Driver Version
1.1.199.3 or later or M933x Arbitrary Waveform Generator Instrument
Drivers installed on your system, download the same from
http://www.keysight.com/find/adnivicomdrivers .
Install the M8190A driver from
http://www.keysight.com/main/software.jspx?ckey=sw385 . Similarly,
locate the installers for the other drivers on Keysight website .
16 Keysight M9099 Waveform Creator 3.2 Startup Guide

Installing WaveformCreator
Keysight M9099 Waveform Creator 3.2 Startup Guide 17
Silent Installation of Waveform Creator
To install Waveform Creator silently, perform the following steps:
1. Copy the following file to a non read-only directory.
* Keysight_M9099_3-2_Setup.exe
2. Run the command prompt as an administrator.
3. Navigate to the directory in which the M9099 Setup file is located.
4. Run the following command:
Keysight_M9099_3-2_Setup.exe /s /v /qn

Setting Up Licenses
Setting Up Licenses
This section describes Keysight software licensing and the licenses required to run
the Keysight Waveform Creator software.
Keysight Software Licensing
The Waveform Creator software supports Node-Locked licensing type.
For more details on different license types and setup, launch Keysight
License Managerfrom Start >All Programs >Keysight License
Manager or by clicking
from the system tray.
When you purchase Waveform Creator, you are provided with a License Redemption
Entitlement Certificate that documents the options to which you are entitled. You can
redeem the certificate at http://www.keysight.com/find/softwaremanager using the
purchase order number, entitlement certificate number, and other details to run the
software.
The Keysight Software Licensing system issues a license file for each purchased
option, by e-mail, to an address you specify. Each license file is a plain text file
attachment with a file name in the form XXXXXX_YYYYYY.lic.
When you receive the e-mail, you should save the attached .lic file(s) to the Agilent
license directory, which is, by default, located at
C:\Program Files\Agilent\licensing.
You can check the status of your software licenses by running the
optional Keysight License Manager or by selectingHelp >About...from
the Waveform Creator menu and then selecting the Licenses tab in
the About dialog.
If a license is not available or not valid, the corresponding features will not be enabled
by the Keysight Waveform Creator.
18 Keysight M9099 Waveform Creator 3.2 Startup Guide

Setting Up Licenses
Keysight M9099 Waveform Creator 3.2 Startup Guide 19
Waveform Creator Licenses
Keysight Waveform Creator Software Options
Product-
Option Feature* Version* Description
M9099T Waveform Creator (Transportable Perpetual
License)
M9099T-
LIC
M9099_CS_
CoreSoftware
3.000 Core product w/ Basic & Multi-tone plug-in
licenses (Required)
M9099T-
AYA
M9099_Wp_
DigMod
3.000 Digital Modulation Library plug-in license
M9099T-
DCS
M9099_Wp_
Docsis
3.000 Docsis 3.1 Plug-in license
M9099T-
DFW
M9099_Dp_
DataFileWrite
3.000 Unencrypted Data File Write plug-in License
M9099T-
SVM
M9099_Wp_
SystemVue
3.000 SystemVue Model plug-in license (requires
SystemVue software)
Waveform Creator Trial licenses
Product- Option Feature Version Description
M9099T-LIC-
TRL
M9099_CS_
CoreSoftware
3.000 Waveform Creator core software
(Trial)
M9099T-AYA-
TRL
M9099_Wp_DigMod 3.000 Digital Modulation Plug-in (Trial)
M9099T-DCS-
TRL
M9099_Wp_Docsis 3.000 Waveform Creator Docsis 3.1 Plug-in
(Trial)
M9099T-SVM-
TRL
M9099_Wp_
SystemVue
3.000 SystemVue Model Plug-in (Trial)

Setting Up Licenses
Waveform Creator Support licenses
Product- Option Feature Version Description
M9099T-LIC-
12M
3.000 Waveform Creator, Core Software, Premium Support
Plan (1-year)
M9099T-AYA-
12M
3.000 Waveform Creator Digital Modulation, Premium
Support Plan (1-year)
M9099T-DCS-
12M
3.000 Waveform Creator Docsis 3.1 Plug-in, Premium
Support Plan (1-year)
M9099T-DFW-
12M
3.000 Waveform Creator Data File Write, Premium Support
Plan (1-year)
M9099T-SVM-
12M
3.000 Waveform Creator SystemVue Model, Premium
Support Plan (1-year)
20 Keysight M9099 Waveform Creator 3.2 Startup Guide