Keysight N9010AK-MTU Installation and operation manual

Option MTU, MultiTouch User Interface Upgrade Kit
Option MTP, MultiTouch User Interface Upgrade Kit
with PC7 CPU
Keysight Technologies
N9010A EXA Signal Analyzer
Installation Note

Notices
© Copyright 2016 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9010-90072
Edition
Edition 1, June 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403

Installation Note N9010-90072 3
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
Introduction
This installation note explains how to install the hardware and licenses to add the MultiTouch user
interface to N9010A EXA signal analyzers.
This installation note supports two kits:
N9010AK-MTU - MultiTouch User Interface Upgrade
N9010AK-MTP - MultiTouch User Interface Upgrade with PC7 CPU
The N9010AK-MTU should only be installed on N9010As that already have the PC6 or PC7 CPU.
This kit includes a new SSD, to ensure that when a disk drive recovery is performed, the software
version recovered will be new enough to recognize the MultiTouch front panel assembly.
The N9010AK-MTP should be installed on N9010As that do not have a PC6 or PC7 CPU. A PC7
CPU is included in this kit, along with a new SSD.
Part of the upgrade process is the license transformation process, which creates new licenses to
replace those of the existing measurement applications. This is because older measurement
application licenses whose model numbers end in the letters "A" or "B" (for example, N9071A or
N9082B) will not work with the new MultiTouch user interface. The license transformation process
will replace "A" and "B" licenses with their equivalent "C" license. For example, N9071A-2FP will be
replaced with N9071C-2FP and N9082B-1FP will be replaced with N9082C-1FP.
Products Affected: N9010A EXA Signal Analyzer
Serial Numbers: All
To Be Performed By: (X) Keysight Service Center
( ) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
2.5 Hours
3.0 Hours
4.0 Hours

4Installation Note N9010-90072
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
IMPORTANT Once this upgrade is performed, the analyzer will only recognize
measurement applications whose model number ends in a "C". For example,
the N9068C, Phase Noise measurement application or the N9071C
GSM/EDGE measurement application.
If the current version of instrument software does not support one of the
transformed licenses, the description as displayed in the Show System
screen will include the phrase "Dormant License UI Conversion". For example,
"N9064A Dormant License UI Conversion, VXA app".
The hardware included in the kit may come in several boxes inside the shipping container

Installation Note N9010-90072 5
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
N9010AK-MTU, MultiTouch User Interface Upgrade Kit Parts List
Quantity Description Keysight Part Number
1 Front Frame Assembly, MultiTouch, Light Color N9020-60261
1 Trim Strip, Top, Benchtop, Light Color N9020-40017
1 Trim Strip, Top, Opt PRC, Light Color N9020-40019
1Vibration Mounta
a. These items will not be needed when upgrading an N9010A.
0460-2725
2 Trim, Side, 177.0 H 5041-9172
1 Plug, Dome, 0.312 in. diameter, black 6960-0076
1Core Bracket, TopaN9020-00071
1Core Bracket, BottomaN9020-00072
1 Knob, RPG, Large W1312-40017
1 Solid State Drive Replacement, WES7 ------------
3Screws, M3 x 0.5 (8 mm long) pan heada0515-0372
9 Screws, M3 x 0.5 (8 mm long) flat head 0515-2032
1 Nameplate, 3.6 GHz, MultiTouch, N9010A N9010-80030
1 Nameplate, 7 GHz, MultiTouch, N9010A N9010-80031
1 Nameplate, 13.6 GHz, MultiTouch, N9010A N9010-80032
1 Nameplate, 26.5 GHz, MultiTouch, N9010A N9010-80033
1 Nameplate, 32 GHz, MultiTouch, N9010A N9010-80034
1 Nameplate, 44 GHz, MultiTouch, N9010A N9010-80035
1 Overlay, Connector, Blank, quartz gray N9020-80140
1 Overlay, Keypad, quartz gray N9020-80165
1 Overlay, Keypad, no EXM port, quartz gray N9020-80167
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
1 Installation Note This note

6Installation Note N9010-90072
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
N9010AK-MTP, MultiTouch User Interface with PC7 CPU Upgrade Kit Parts List
Quantity Description Keysight Part Number
1 Front Frame Assembly, MultiTouch, Light Color N9020-60261
1 Trim Strip, Top, Benchtop, Light Color N9020-40017
1 Trim Strip, Top, Opt PRC, Light Color N9020-40019
2 Trim, Side, 177.0 H 5041-9172
1 Plug, Dome, 0.312 in. diameter, black 6960-0076
1 Knob, RPG, Large W1312-40017
1 CPU Module 2.2 GHz Dual Core Celeron, 8 GB RAM W1312-60210
1 Tray Assembly, solid state drive, 160 GB W1312-60302
9 Screws, M3 x 0.5 (8 mm long) flat head 0515-2032
1 Nameplate, 3.6 GHz, MultiTouch, N9010A N9010-80030
1 Nameplate, 7 GHz, MultiTouch, N9010A N9010-80031
1 Nameplate, 13.6 GHz, MultiTouch, N9010A N9010-80032
1 Nameplate, 26.5 GHz, MultiTouch, N9010A N9010-80033
1 Nameplate, 32 GHz, MultiTouch, N9010A N9010-80034
1 Nameplate, 44 GHz, MultiTouch, N9010A N9010-80035
1 Overlay, Connector, Blank, quartz gray N9020-80140
1 Overlay, Keypad, quartz gray N9020-80165
1 Overlay, Keypad, no EXM port, quartz gray N9020-80167
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
1 Installation Note This note

Installation Note N9010-90072 7
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
Tools Required
— T-10 TORX Driver
— T-20 TORX Driver
— 5/16-inch torque wrench
— Deep 5/16-inch socket wrench
— ¼-inch open-end wrench
— Scissors or knife
—Diagonalcutters
— Microsoft Windows based personal computer with internet access and USB port
— USB storage device with > 2 GB free memory
Initial Instrument Functionality Check
Power on the instrument and allow the instrument to boot up. Run an alignment and display the
measurement screen. (The instrument will probably display a spectrum analyzer screen and you will
see the instrument sweeping.)
There should be no alignment failures. If there are failures, investigate and fix the problem before
continuing.
Before you disassemble the instrument, turn the power switch to Standby. After the instrument
has completely shut down, unplug the instrument. Failure to unplug the instrument can result in
personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.

8Installation Note N9010-90072
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
Installation Procedure
Analyzer Information
1. Connect a power cord to the analyzer and turn on the analyzer.
2. After the analyzer has completed turning on, press System, Show, System. Make note of the
following information from the Show System screen:
Product Number: _____________
Serial Number: ______________
Instrument S/W Revision: ______________
3. Check for the presence of one of the following options listed below in the Show System
screen. Put a check mark or “X” after the option listed below that appears in the Show System
screen.
N9010A-PC1_____
N9010A-PC2_____
N9010A-PC3_____
N9010A-PC4_____
N9010A-PC5_____
N9010A-PC6_____
N9010A-PC7_____
N9010A-532_____
N9010A-544_____
N9010A-EXM_____
4. Refer to the data in step 2 above. If the Product Number is not N9010A, do not proceed with
the installation of this kit. This kit is to be installed only on N9010A signal analyzers.
5. Refer to the data in step 3 above. If upgrade product N9010A-MTU is being installed and the
currently installed CPU is either N9010A-PC1, N9010A-PC2, N9010A-PC3, N9010A-PC4, or
N9010A-PC5, do not proceed with the installation of this kit. This kit is to be installed only on
N9010A signal analyzers with N9010A-PC6 or N9010A-PC7 CPUs.
6. Refer to the data in step 3 above. If the upgrade product N9010A-MTP is being installed and
the currently installed CPU is N9010A-PC6 or N9010A-PC7, do not proceed with the
installation of this kit. This kit is to be installed only on N9010A signal analyzers with
N9010A-PC1, N9010A-PC2, N9010A-PC3, N9010A-PC4, or N9010A-PC5 CPUs.
7. Refer to the data in step 3 above. If Option N9010A-EXM is installed, there will be additional
steps required to remove and replace the front panel assembly.

Installation Note N9010-90072 9
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
License Key Backup
In order for the instrument being upgraded to keep the same option configuration that it had prior
to the upgrade, it is mandatory that the licenses be transferred from the original disk drive to the
new disk drive. In most cases, these licenses will be automatically copied from the Midplane board
assembly. However, there may be instances where the automatic copying process will not work.
Therefore, the license keys will also be backed up for later restoration on the new disk drive.
1. Connect a mouse and external keyboard to the analyzer using the rear panel USB ports.
2. Locate a USB storage device. Perform a virus scan on this device before use.
3. Create a folder on the USB storage device with the folder name "Licenses" followed by the
model number and serial number of the analyzer being upgraded. For example,
"Licenses_N9010A_MY50060101"
4. Insert the USB storage device into one of the analyzer's USB ports.
5. Using the mouse, navigate to the folder C:\Program Files\Agilent\licensing.
6. Change the folder's properties so that hidden files can be viewed.
a. If the operating system is WinXP, click on Tools and select Folder Options. Select the View
tab. In the Advanced Settings window, under Hidden files and folders, select "Show hidden
files and folders".
b. If the operating system is Windows Embedded Standard 7 (WES7), click on Organize and
select Folder and search options. Select the View tab. In the Advanced Settings window,
under Hidden files and folders, select "Show hidden files and folders".
7. Copy the contents of the C:\Program Files\Agilent\licensing folder to the Licenses… folder
created on the USB storage device.
a. To select all of the licenses in the folder, click on any of the licenses and then press Ctrl-A
on the external keyboard.
b. To copy the selected files, press Ctrl-C.
c. Navigate to the "Licenses_..." folder on the USB storage device for the instrument being
upgraded and press Ctrl-V to paste all the licenses into the folder.

10 Installation Note N9010-90072
Option MTU and MTP, MultiTouch User Interface Upgrade Kits
Backup Calibration Data
There are three different backup procedures that might need to be followed. Which backup
procedure to be run will depend on the software version that currently exists in the instrument
being upgraded.
To determine which calibration data backup procedure needs to be run compare the current
instrument software version that was recorded in the Analyzer Information section step 2 of this
document and follow the steps outlined below for that version.
S/W Revision Less Than A.01.55
Instruments with a software version older than A.01.55 will first need to have the software updated
to the latest version prior to being able to backup the instrument calibration data. See the Software
Updates section of this document for instructions on updating the instrument software.
Once the software has been updated, use the calibration data backup procedure under the heading
"S/W Revision Greater Than A.02.00".